Manual Iomega Screenplay Pro Hd 3s4i3x

Page 1 of 62

™

ScreenPlay Pro HD Multimedia Player

The Iomega ScreenPlay Pro HD Multimedia Drive is a high definition multimedia player that connects to your home theatre and your home network to store and access your videos, music, and photo collections. Easily browse your home network to select stored videos to view on your home theatre, or transfer multimedia files onto the ScreenPlay Pro HD via the network or by connecting directly to USB on your computer. You can also record video directly to the ScreenPlay Pro HD from cameras, cable, or your VCR. NOTE: It may be a criminal offense under applicable copyright laws to make unauthorized copies of copyright protected material, including videos, films, broadcasts, and nonoriginal sound and video recordings. This equipment should not be used for these purposes.

Iomega, the stylized "i" logo, and ScreenPlay are either ed trademarks or trademarks of Iomega Corporation in the United States and/or other countries. Microsoft and Windows are either ed trademarks or trademarks of Microsoft Corporation in the United States and/or other countries. Certain other product names, brand names, and company names may be trademarks or designations of their respective owners.

€

http://www.iomega.com//manuals/hdd2008/scrnplyprohd/en/printall.html

07/04/2009

Page 2 of 62

€ €

About the ScreenPlay Pro HD Multimedia Drive

ed Media Formats

Front Controls and Indicators

ed AV Connections

Rear Components

System Requirements

Safety Guidelines

Package Contents

ed Media Formats The ScreenPlay Pro HD s the following types of multimedia files: Audio

€

Video*

€

Photos €

€

AAC AC3 (Dolby Digital Encoding) € € AIFF DTS € € MP3 M4A € € OGG Vorbis PCM € € WAV WMA € € MPEG-1 € MPEG-2 — AVI, VOB € MPEG-4 — AVI, DivX 3.11, 4.x, 5.x, XviD € DivX HD € DVD € BMP € JPG € JPEG €

*ed file extensions for videos and associated audio/ files include avi, dat, divx, mov, mp2, mp4, mpe, mpeg, mpg, m4a, m4v, vob, xvid, ifo, iso (DVD ISO), MKV, DMF, TS

NOTE: Although the ScreenPlay Pro HD s the listed file types, it might not be able to every codec used to create the files. Check the area on www.iomega.com for the latest information on ed file types.

| top of page |

ed AV Connections


07/04/2009

Page 3 of 62

The ScreenPlay provides high quality audio/video output through the following TV connections:

HDMI (High-Definition Multimedia Interface) — s 480p, 576p, 720p 50/60 Hz, and 1080i 50/60 Hz € Composite video and audio R/L € Component video: Y, Pb, Pr — s 480i/480p, 576p, 720p, and 1080i € Coaxial S/PDIF output €

CAUTION! The ScreenPlay Pro HD is not intended for in-car entertainment use. Unstable power or vibration may damage the ScreenPlay hard drive.

| top of page |

System Requirements When the ScreenPlay Pro HD is connected directly to a computer, the system must meet these minimum requirements:

350 MHz Pentium class processor or higher

Microsoft Windows 2000 Professional / XP Home / XP Professional /

®

®

™

XP Professional 64x / Windows Vista (all versions)

Available USB connection

1

NOTE: Transfer speed to the ScreenPlay Pro HD will be slower if is it connected to a USB 1.1 port.

| top of page |

Package Contents


07/04/2009

Page 4 of 62

Iomega ScreenPlay

Remote Control

Power Supply and Cord

USB 2.0 Cable

Composite AV Cable

HDMI Cable

NOTE: Package contents may vary. For maximum transfer rate and reliability, use the cables provided.

| top of page |

Front Controls and Indicators


07/04/2009

Page 5 of 62

1. Remote receiver—When using the remote control, always point it toward the receiver. receiver 2. Remote indicator LED—Blinks orange once to indicate receiving a signal from the remote LED control. NOTE: Media player functions controlled by the remote are available only when the ScreenPlay Pro HD is connected to a TV. Some functions are not ed by all playable file types. 3. Up—Press Up to navigate up through folders or menus. 4. Down—Press to navigate down through folders or menus. Down 5. Left—In browser mode, press to move left through menu options. When a photo is Left displayed, press to rotate the image counterclockwise. During video playback, press for fast rewind. 6. Right—In browser mode, press to move right through menu options. When a photo is Right displayed, press to rotate the image clockwise. During video playback, press for fast foward. to play the current selected file or enter a folder. Press again to pause 7. Play/Pause—Press Play/Pause playback.


07/04/2009

Page 6 of 62

8. Stop—Press to stop current playback. In browser mode, press to return to previous Stop folder or menu. 9. NTSC/PAL—Press to change video output mode as follows: NTSC/PAL NTSC→ PAL→ 480p→ 576p→ 720p€50Hz→ 720p€60Hz→ 1080i€50Hz→ 1080i€60Hz 10. Power and access LED—Glows blue when the ScreenPlay Pro HD is connected to power; LED blinks when the ScreenPlay Pro HD is loading or accessing files. 11. Standby button—Press to activate the ScreenPlay Pro HD for playback. To return to button standby mode, press and hold for three seconds, then release.

| top of page |

Rear Components

1. Fan vent—Do not block! vent 2. Security Lock— Lock—Connect a security cable to prevent theft.


07/04/2009

Page 7 of 62

3. Composite video output connector—Use for composite connection to a TV; connect to connector yellow video input jack on the TV. 4. RCA stereo audio output connectors—Use for composite audio connection; connect to connectors red/white audio input jacks on the TV. 5. Composite video input connector—Use to connect VCR, DVD player, or other video input connector to the ScreenPlay Pro HD for either recording or -through playback. 6. RCA audio input connectors—Use connectors to connect VCR, DVD player, or other audio input to the ScreenPlay Pro HD for either recording or -through playback. 7. USB 2.0 host port—Use to connect a WiFi adapter or external USB drive to the ScreenPlay port Pro HD. NOTE: External USB device must be formatted NTFS or FAT32. 8. Component video output connectors—Connect to green, blue, and red video jacks on connectors the TV (component cable not included). NOTE: Not all TV sets component video. 9. Ethernet connector—Use for wired network connection (Ethernet cable not included). connector 10. HDMI connector—Use to connect the ScreenPlay Pro HD to an HDTV or high definition connector Home Theater System. Outputs standard, enhanced, or high-definition video, plus multi-channel audio (surround sound). 11. Coaxial digital audio connector—Outputs digital audio signal. Connect to a receiver connector using an RCA cable (not included). 12. USB 2.0 device connector—Use when connecting the ScreenPlay Pro HD directly to a connector computer. 13. Power connector—Always connect the included power supply when using the ScreenPlay connector Pro HD.

| top of page |

Safety Guidelines

Do not operate the ScreenPlay Pro HD with wet hands or near water.

Do not bend cables in a sharp angle.

Keep the ScreenPlay Pro HD and cables out of reach of children.


07/04/2009

Page 8 of 62

Keep the ScreenPlay Pro HD and its accessories away from heat sources.

| top of page |

€


07/04/2009

Page 9 of 62

€ €

About the Remote Control

Remote Control Functions

First Time Use of the Remote Control

Replacing the Battery in the Remote Control

Remote Control Functions When the Iomega ScreenPlay Pro HD is connected to the TV, you can use the remote control to navigate menus and play content. STANDBY €€ TV SYS

Activate the ScreenPlay Pro HD / Return to Standby Toggle video output mode (NTSC→ PAL→ 480p→ 576p→ 720p€50Hz→ 720p€60Hz→ 1080i€50Hz→ 1080i€60Hz)

SETUP

Jump to the Setup menu to configure device options

SOURCE

Select video input source

AUDIO

Select an audio track when playing movie

SUBTITLE

Switch DVD / DivX subtitles

ANGLE

Select angle when playing movie

ZOOM

Zoom 2x / 3x / 4x / 8x

RETURN

Go to parent directory

SLOW

Slow motion (1x, 3/4x, 1/2x, 1/4x, 1/8x, 1/16x)

REC

Press once to record / repeat press for record length setup

DELETE

Delete files (only in browser mode)

UP/DOWN

Navigate up or down through menus in browser mode

LEFT/RIGHT Navigate menus in browser


07/04/2009

Page 10 of 62

mode / rotate photo image

€

ENTER

Select option / play file /

€ HOME

pause playback €

MENU

Display menu

Display the ScreenPlay Pro HD main menu

€ STOP

Stop playback

€

Fast forward

when playing DVD movie* €

Fast rewind (1.5x / 2x / 4x / 8x / 16x / 32x)

€

Previous page in browser

(1.5x / 2x / 4x / 8x / 16x / 32x)

€

preview mode €

DISPLAY Display file properties /

Next page in browser preview mode

€ GOTO

information

Press to jump to a specific point on a title

(specify title,

chapter, and time)

€

A→B

Set A and B points for

€ REPEAT

repeat €

Press to change the repeat mode (repeat 1 / all / off)**

Increase volume

€

Decrease volume

€

€ €

€

€

€

€

*Press the MENU key in browser mode to display a menu that enables you to copy, paste, or delete files. **The default mode is repeat off. Repeat 1 is available only for music files.

NOTES:

The ScreenPlay Pro HD must be activated before it will respond to commands from the remote control.

Always point the remote control towards the receiver on the front of the ScreenPlay Pro HD.

Some functions on the remote control are not ed by all media types. If you select a function that is not ed, the ScreenPlay will display an icon indicating that it cannot respond to the selected command.

| top of page |

First Time Use of the Remote Control Before using the remote control for the first time, enable battery power by pulling out the plastic tab.

| top of page |


07/04/2009

Page 11 of 62

Replacing the Battery in the Remote Control When the battery is depleted, replace it with a new CR2025 3 volt battery. Follow the instructions below. 1. Turn the remote control so the back side is up. 2. Press the tab on the bottom edge with your fingernail to release the battery holder. 3. Hold the battery holder at the indentation and pull out the battery unit. 4. Remove the old battery from the holder and replace it with a new CR2025 battery. IMPORTANT! Insert the new battery with the positive (+) side facing up. 5. Insert the battery holder into the remote control. Make sure it is seated securely.

| top of page |

€


07/04/2009

Page 12 of 62

€ €

Connecting the ScreenPlay Pro HD

Connecting to a Computer

Connecting to a Network

Connecting to a TV

Connecting to a Computer via USB

Formatting the ScreenPlay Pro HD Hard Drive

Transferring Files on a Computer Connection

Disconnecting from USB

USB Guidelines

Connecting to a Computer via USB Use the following instructions to connect the ScreenPlay Pro HD directly to a computer via USB. Note that the computer must meet minimum system requirements to the ScreenPlay Pro HD. 1. Connect the USB cable to the back of the ScreenPlay Pro HD and to a USB port on the computer. Look for "USB" or the USB symbol, which usually identifies the USB connection. Some USB 2.0 cards do not have USB notations. If you cannot locate the USB connection on your computer, refer to your computer documentation or the USB 2.0 card documentation. NOTE: Drive performance will be slower if connected to USB 1.1. 2. Connect the included power supply to the drive. Place the drive on a stable surface and connect the power supply to an uninterruptible power supply (UPS) or power outlet. CAUTION! Do not move the drive while it is powered up to avoid drive damage or data loss. Use only the power supply included with the drive. 3. Press the power button on the front of the ScreenPlay Pro HD to turn it on. NOTE: The blue LED on the ScreenPlay Pro HD glows when the drive is powered up.


07/04/2009

Page 13 of 62

The LED blinks when the ScreenPlay Pro HD is loading or accessing files. 4. The Iomega ScreenPlay Pro HD drive icon should appear in My Computer or Windows Explorer. If the drive does not appear on your computer, refer to Troubleshooting. 5. OPTIONAL: After the drive is recognized by the operating system, insert the Solutions CD and install the Playlist Manager and Transcode utilities. If the CD menu does not open automatically, launch the Start program on the CD.

| top of page |

Formatting the ScreenPlay Pro HD Hard Drive The ScreenPlay Pro HD hard drive ships pre-formatted with an NTFS file system, which ™

optimizes performance with Windows 2000, Windows XP, and Windows Vista . If you reformat the drive, it is recommended that you use the Windows format utility to reformat with NTFS. NOTES:

The ScreenPlay Pro HD must be formatted either NTFS or FAT32 in order to play back media files on a TV.

Do not partition the ScreenPlay Pro HD hard drive - leave it as a single large volume. Only media files stored on the primary partition can be viewed or played on a TV.

CAUTION! Formatting the drive will erase all existing data! If you have files on the drive you want to save, move them to another drive before reformatting.

| top of page |

Transferring Files on a Computer Connection When the ScreenPlay Pro HD is connected directly to a computer, you can use the standard methods for your operating system to create folders on the drive, then save or drag and drop files, just as you would to any other drive attached to your computer. You can also media files directly to the ScreenPlay Pro HD. See Organizing Your Multimedia Files for suggestions on using folders to store and organize your files. NOTE: You can also transfer files to the ScreenPlay Pro HD via a network connection.


07/04/2009

Page 14 of 62

| top of page |

Disconnecting from USB Disconnect the ScreenPlay Pro HD from the computer before connecting to a TV. Before disconnecting, make sure you save files and close all files and folders on the drive to avoid losing data. Always use the safe removal procedure for your operating system to avoid corrupting the file system on the ScreenPlay Pro HD.

Disconnecting using Windows Vista/XP/2000 Use the Safely Remove Hardware utility before you disconnect power or the USB cable from the ScreenPlay Pro HD. 1. Ensure all files or programs on the drive are closed. 2. Double click the Safely Remove Hardware icon on the taskbar.

3. Select the ScreenPlay Pro HD USB drive and click Stop; Stop a new window will open. 4. Select the drive again and click OK. OK 5. You can then safely disconnect the drive.

| top of page |

USB Guidelines Read and follow these guidelines to ensure optimal and reliable performance of your Iomega ScreenPlay Pro HD drive. You can...

You can connect or disconnect the drive while the computer is on. NOTE: Always use the safe removal procedure for your operating system when disconnecting the drive.

You can optimize drive performance by disconnecting other USB devices when using your ScreenPlay Pro HD. The performance of all USB devices decreases as additional USB devices are connected.


07/04/2009

Page 15 of 62

You can avoid some system lockups by waiting at least 30 seconds after connecting or disconnecting any USB device to allow the system to re-enumerate the USB bus. Do not connect, disconnect, or use any other USB device during this time.

Do not...

Do not connect or disconnect any USB device while the drive is transferring information. Data loss will result!

Never use USB extension cables with your Iomega ScreenPlay Pro HD drive. Data loss might result.

Do not connect the drive to a hub; connect only to the computer.

| top of page |

€


07/04/2009

Page 16 of 62

€ €




Connecting to a TV

Connecting to a Wired Network

Connecting to a Wireless Network

Connecting to the ScreenPlay Pro HD from a Networked Computer

Transferring Files via the Network

Connecting to a Wired Network You can connect the ScreenPlay Pro HD to a TV and your network at the same time. This allows you to either view media files directly from your network (streaming), or transfer files to and from the ScreenPlay Pro HD while it is connected to a TV. 1. Use a standard ethernet cable to connect the ScreenPlay Pro HD to a network router, hub, or switch. — or — Connect the ScreenPlay Pro HD to the Ethernet port on a networked computer.

NOTE: The package does not include an ethernet cable. 2. Connect the included power supply to the drive. Place the drive on a stable surface


07/04/2009

Page 17 of 62

and connect the power supply to an uninterruptible power supply (UPS) or power outlet. CAUTION! Do not move the drive while it is powered up to avoid drive damage or data loss. Use only the power supply included with the drive. 3. The ScreenPlay Pro HD is automatically configured so you can browse and play back files stored on your network volumes. If you want to copy files from your network volumes to the ScreenPlay Pro HD, you need to connect to the ScreenPlay Pro HD using a computer on the network.

| top of page |

Connecting to a Wireless Network The ScreenPlay Pro HD is WiFi-ready and can connect to a wireless network using a ed WiFi adapter. NOTE: The package does not include a WiFi adapter. Check the area on www.iomega.com for the latest information on ed WiFi adapters. Follow the instructions below to set up the wireless connection for your ScreenPlay Pro HD. 1. Connect the WiFi adapter to the USB host port on the back of the ScreenPlay Pro HD drive. 2. If you have not already done so, connect the ScreenPlay Pro HD to your TV. 3. Turn on your TV and change the input setting as needed to receive input from the ScreenPlay Pro HD. Refer to the manual that came with the TV if you are uncertain how to do this. 4. Activate the ScreenPlay Pro HD by pressing the STANDBY button on either the remote control or the front of the ScreenPlay drive. NOTE: When using the remote control, always point it towards the receiver on the front of the ScreenPlay Pro HD. 5. When the main ScreenPlay menu displays on the TV, select Setup and press the ENTER key. 6. Select Network and press the ENTER key. 7. Select Wireless Setup and press the ENTER key. 8. Select Modify and press the ENTER key.


07/04/2009

Page 18 of 62

9. The ScreenPlay Pro HD will list available wireless networks. Select your network and press the Enter key. NOTE: To enter a name and to to a network volume, press the ENTER key on the remote control. This will bring up a virtual keyboard on the ScreenPlay Pro HD TV display. Use the remote control cursor keys and the ENTER key to select the necessary characters. The can use any combination of numbers and letters (lower case or caps). It can also use periods. It cannot use extended punctuation characters (such as !, @, #, $, %, &, etc.) 10. Configure the settings for connection mode, wireless SSID, and wireless security. 11. When the configuration is complete, the ScreenPlay Pro HD will automatically connect to the wireless network. If it connects successfully, you will see a message indicating "Test complete", and the Nework Setup menu will display showing the IP address used by the ScreenPlay Pro HD. 12. Press the HOME key to return to the ScreenPlay Pro HD main menu.

| top of page |

Connecting to the ScreenPlay Pro HD from a Networked Computer You can run the ScreenPlay Discovery utility to automatically map a drive letter to the ScreenPlay Pro HD on a PC connected to the network, or you can manually map a drive letter. NOTE: The network computer must be on the same subnet or network segment as the ScreenPlay Pro HD.

Automatically mapping a drive letter with ScreenPlay Discovery 1. Insert the the Solutions CD and install the ScreenPlay Discovery utility. 2. Run ScreenPlay Discovery to automatically connect to the ScreenPlay Pro HD: a. Click Start€→ Iomega€→ ScreenPlay Pro HD Start Iomega b. Double click the icon for ScreenPlay Discovery. Discovery

Manually mapping a drive letter from a Windows PC 1. If you have not already done so, connect the ScreenPlay Pro HD to your TV.


07/04/2009

Page 19 of 62

2. Turn on your TV and change the input setting as needed to receive input from the ScreenPlay Pro HD. Refer to the manual that came with the TV if you are uncertain how to do this. 3. Activate the ScreenPlay Pro HD by pressing the STANDBY button on either the remote control or the front of the ScreenPlay drive. NOTE: When using the remote control, always point it towards the receiver on the front of the ScreenPlay Pro HD. 4. When the main ScreenPlay menu displays on the TV, select Setup and press the ENTER key. 5. Select Network and press the ENTER key. The display will show the IP address assigned to the ScreenPlay Pro HD on your network. 6. Using a PC connected to the Network, right click on the Computer (Vista) or My Computer (XP/2000) icon and select Map Network Drive. Drive 7. Select the drive letter you want to use for the ScreenPlay Pro HD, then enter the IP address for the ScreenPlay Pro HD in the field next to Folder (for example, \\192.168.1.151). \\192.168.1.151 8. You can now use My Computer or Windows Explorer to browse the ScreenPlay Pro HD and copy files from your network volumes onto the ScreenPlay Pro HD.

NOTE: If you need to enter a name and to to a network volume, press the ENTER key on the remote control. This will bring up a virtual keyboard on the ScreenPlay Pro HD TV display. Use the remote control cursor keys and the ENTER key to select the necessary characters. The can use any combination of numbers and letters (lower case or caps). It can also use periods. It cannot use extended punctuation characters (such as !, @, #, $, %, &, etc.)

| top of page |

Transfering Files to the ScreenPlay Pro HD via the Network After mapping a drive letter to the ScreenPlay Pro HD, you can use the standard methods for your operating system to create folders on the drive, then save or drag and drop files, just as you would to any other drive attached to your computer. By using a network connection, you can transfer files to and from the ScreenPlay Pro HD while it’s connected to a TV. You can also view files directly from the network. See Using the ScreenPlay Pro HD for more information on playing media files. See Organizing Your Multimedia Files for suggestions on using folders to store and


07/04/2009

Page 20 of 62

organize your files.

| top of page |

€


07/04/2009

Page 21 of 62

€ €




Connecting to a TV

Connecting to an HD TV via HDMI

Connecting Coaxial Audio

Connecting Composite Video

Activating the ScreenPlay for

Connecting Component Video

Playback

Disconnecting from TV

Connecting to an HD TV via HDMI HDMI (high-definition multimedia interface) s standard, enhanced, or highdefinition video, plus multi-channel digital audio, on a single cable connection. This connection option is ed only on high-definition (HD) TVs. 1. Connect the HDMI cable to the back of the ScreenPlay Pro HD drive. 2. Connect the other end of the HDMI cable to the HDMI input connection on the TV set.

| top of page |

Connecting Composite Video with RCA Audio Composite video is compatible with most TV sets. The following instructions use the composite video connector on the ScreenPlay Pro HD and the RCA audio connectors. 1. Connect the composite AV cable to the composite video output connector (top yellow) and the RCA audio output connectors (top red and white) on the back of the ScreenPlay Pro HD drive, matching the colors. 2. Connect the yellow (video) connector on the other end of the cable to the composite VIDEO input connection on the TV set. 3. Connect the white connector to the Left (L) audio input connection on the TV set.


07/04/2009

Page 22 of 62

4. Connect the red connector to the Right (R) audio input connection on the TV set.

| top of page |

Connecting Component Video with RCA Audio NOTE: You will need to obtain a component video cable to use this connection option. If your TV s component video, you can use this connection for better video quality. With a component video connection, you can configure configure display ratio, progressive scan, and resolution up to 1080i using the Setup menu > Video setup. For the audio connection with component video, you can use the red and white audio connectors on the composite AV cable to connect RCA audio. For better audio quality, you can use a coaxial audio cable (not included). 1. Connect the component video cable to the component output connectors (red, blue, green) on the back of the ScreenPlay Pro HD drive, matching the colors. 2. Connect the other end of the cable to the component video input connections on the TV set, matching colors of the jacks. 3. Using the composite AV cable, connect red and white connectors to the RCA audio output connectors on the back of the ScreenPlay Pro HD drive, matching the colors. 4. Connect the white connector on the composite AV cable to the Left (L) audio input connection on the TV set. 5. Connect the red connector on the composite AV to the Right (R) audio input connection on the TV set. NOTE: Some TV sets are equipped with separate composite and component audio inputs. Be sure that you have connected the correct one.

| top of page |

Connecting Coaxial Audio The ScreenPlay Pro HD drive includes a coaxial audio connector for high quality digital audio output. You will need to obtain a coaxial cable to connect the ScreenPlay Pro HD to an AV amplifier (receiver) with a digital audio decoder. NOTE: You will get multi-channel sound effect only if the audio source file carries it.


07/04/2009

Page 23 of 62

| top of page |

Activating the ScreenPlay Pro HD for Playback After completing the video and audio connections you want to use, connect the ScreenPlay Pro HD to power. Press the STANDBY button on the remote control or front of the drive to power on (activate) the ScreenPlay Pro HD. During activation, the blue LED will blink brightly for several seconds. When the blue LED glows brightly and steadily, the ScreenPlay Pro HD is ready to use for playback. NOTE: Pressing the STANDBY button again will return the ScreenPlay Pro HD to Standby mode. While in Standby mode, the ScreenPlay Pro HD will not respond to other navigation or command buttons.

| top of page |

Disconnecting from TV Always put the ScreenPlay Pro HD in Standby mode before disconnecting cables or moving the drive. Press the STANDBY button on the remote control or front of the drive, then wait until the ScreenPlay display turns off and the blue LED stops blinking. It is then safe to disconnect cables and move the drive.

| top of page |

€


07/04/2009

Page 24 of 62

€ €

Using the ScreenPlay Pro HD Multimedia Player

Using the Front Controls

Listening to Music

Organizing your Multimedia Files

Viewing Photo Images

Navigating Menus on the TV

Using Playlist Manager

Viewing Files from a Network

Recording TV or Video

Playing Video Files

Viewing Recorded TV or Video

Using the Front Controls When the ScreenPlay Pro HD is connected to a TV and activated for playback, you can use the controls on the front to navigate through folders and play back multimedia files. If you need to change the regional standard used by the ScreenPlay Pro HD, press the NTSC/PAL button. See Front Controls and Indicators for information on the functions of the other buttons.

| top of page |

Organizing your Multimedia Files The main folder on the ScreenPlay Pro HD is called "ROOT". It is recommended that you create folders at the ROOT level for organizing and storing your multimedia files. You might find it helpful to create a folder for each type of media you place on the drive (for example, "Photos" for image files, "Music" for music files, and "Videos" for video files). Within these folders, you can create additional subfolders to organize your files. For example, within the "Videos" folder, you could create a separate folder for each movie or video you want to store on the ScreenPlay Pro HD. You can also create subfolders to organize your media files into categories that will make it easy for you to find the files you want to play. For example, within the "Videos" folder, you could create subfolders for "Classics", "Family Favorites", "Action and Suspense", etc. NOTE: It is not necessary to place your media files in folders or subfolders; however, this is recommended for easiest navigation. If you copy all of your media files directly to the ROOT level without using folders, it will be more difficult to find and play back specific files.

| top of page |


07/04/2009

Page 25 of 62

Navigating Menus on the TV When the ScreenPlay Pro HD is connected to a TV and activated for playback, the main menu (Home menu) will display on the TV screen. You can also jump to the main menu during playback or while browsing other menus by pressing the HOME key on the remote control.

The options on the right hand side of the main menu allow you to select a location to browse for media files or select menus for configuring the ScreenPlay Pro HD.

ScreenPlay Pro

Browse folders and files located on the ScreenPlay Pro HD hard drive.

External USB

Browse folders and files located on an external USB device connected to the USB 2.0 host port on the ScreenPlay Pro HD. NOTE: The USB device must be formatted NTFS or FAT32 to playback on the TV. If the USB drive is partitioned, the ScreenPlay Pro HD will read only the first partition.

Network

Browse shared network volumes when the ScreenPlay Pro HD is connected to a network.

AV Input

Switch the display to view the TV input or an AV input source connected to the ScreenPlay Pro HD.

Schedule

Set up a schedule to record TV programs onto the ScreenPlay Pro HD. NOTE: Set the time clock on the ScreenPlay Pro HD before setting up a recording schedule. See Setup > System > Time.


07/04/2009

Page 26 of 62

Setup

Set up configuration options for the ScreenPlay Pro HD. See Setup Options for detailed information.

To navigate the menus, use the Up/Down arrow keys on the remote control or front to move the highlight bar through menus, options, or files. Press the ENTER key or Play/Pause button to open a folder, select an option, or play a file. Press the RETURN key to return to a previous page or menu.

| top of page |

Viewing Media Files from Your Network You can use the ScreenPlay Pro HD to play media files from your network on your TV. 1. Connect the ScreenPlay Pro HD to your TV. 2. Connect the ScreenPlay Pro HD to your home network. 3. Turn on your TV and change the input setting as needed to receive input from the ScreenPlay Pro HD. Refer to the manual that came with the TV if you are uncertain how to do this. 4. Activate the ScreenPlay Pro HD by pressing the STANDBY button on either the remote control or the front . NOTE: When using the remote control, always point it towards the receiver on the front of the ScreenPlay Pro HD. 5. From the ScreenPlay Pro HD Home menu, select Network and press the ENTER key. 6. The Network menu will show volumes available on your network. Use the cursor keys on the remote control or front of the drive to browse to and select media files you want to play. NOTE: If you need to enter a name and to to a network volume, press the ENTER key on the remote control. This will bring up a virtual keyboard on the ScreenPlay Pro HD TV display. Use the remote control cursor keys and the ENTER key to select the necessary characters. The can use any combination of numbers and letters (lower case or caps). It can also use periods. It cannot use extended punctuation characters (such as !, @, #, $, %, &, etc.)

| top of page |


07/04/2009

Page 27 of 62

Playing Video Files Use the following steps to play video files on your TV. 1. Connect the ScreenPlay Pro HD to your computer and copy all files needed for the video onto the ScreenPlay Pro HD. You can also copy video files to the ScreenPlay Pro HD using a network connection or play video files directly from your home network or a USB device connected to the ScreenPlay Pro HD. 2. Connect the ScreenPlay Pro HD to your TV. 3. Turn on your TV and change the input setting as needed to receive input from the ScreenPlay Pro HD. Refer to the manual that came with the TV if you are uncertain how to do this. 4. Activate the ScreenPlay Pro HD by pressing the STANDBY button on either the remote control or the front . NOTE: When using the remote control, always point it towards the receiver on the front of the ScreenPlay Pro HD. 5. Select a location to browse for the video file you want to play. Select ScreenPlay Pro if the file is saved on the ScreenPlay Pro HD hard drive, Network if the file is stored on a network volume, or External USB if the file is located on an external USB device connected to the ScreenPlay Pro HD. 6. Browse to the folder containing the video you want to play (use the Up/Down buttons on either the remote control or the front to navigate through listed folders; press the ENTER key to open a folder or subfolder). 7. Select a video file and press the ENTER key or Play/Pause button to start playback.

Playable Video Files You can use the ScreenPlay Pro HD to play back videos formatted MPEG-1, MPEG-2, or MPEG-4, including DivX, DivX HD, XviD, and DVD movies. See ed Media Formats for a complete list of ed video types and file formats. The table below provides additional information on MPEG video formats, icons, and filenames. NOTE: Although the ScreenPlay Pro HD s the following file extensions, it might not be able to every codec used to create the files. Check the area on www.iomega.com for the latest information on ed file types.

Video Format MPEG-1 (VCD)

Icons

Notes This icon indicates an MPEG-1 video file. The filename extension can be .dat, .mpg, .mpe, or .mpeg.


07/04/2009

Page 28 of 62

MPEG-2 (AVI, VOB)

This icon indicates the IFO file for a DVD movie. Select this file to play the entire DVD movie with DVD menu. This icon indicates an MPEG-2 VOB file. The filename extension can be .mpg, .vob, or .m2p. Playing a single VOB file directly will cause some DVD functions to be lost. See DVD Folder below for more information.

MPEG-4 (AVI, DivX,

This icon indicates a DivX / Xvid movie file. The

XviD)

filename extension can be .avi, .divx, or .xvid. This icon indicates a DivX / Xvid subtitle file. The filename extension can be .srt, .sub, .idx, .ssa, or .smi. The subtitle filename must match the video file except for the extension.

NOTE: For DivX subtitle text files encoded in ANSI code, the Subtitle Language must be set to match the language of the subtitle text file. Subtitle files encoded with Unicode (UTF-8) will display properly regardless of the language setting. If needed, use Setup > Language > Subtitle to adjust the language setting.

| top of page |

DVD Folder A DVD folder contains complete files for a DVD movie. The ScreenPlay Pro HD can play back a movie from a DVD folder just like playing back a DVD disc. To create a DVD folder, connect the ScreenPlay Pro HD to your computer, insert the DVD disc into the computer's optical drive, and use My Computer or Windows Explorer to browse the disc. Copy the entire "VIDEO_TS" folder from the DVD to the ScreenPlay Pro HD. To play the DVD movie, navigate to the VIDEO_TS folder, select the VIDEO_TS IFO file and press the ENTER key on the remote control or the Play button on the front . NOTE: If the DVD folder is incomplete, you can still play back the VOB files directly. Functions controlled by the IFO file, such as the selection of subtitles, chapters, and angles, will be lost. IMPORTANT! Some DVD discs cannot be copied because they have been protected with CSS protection. Always obey copyright and intellectual property rights. Do not copy DVDs with copyright and do not distribute them to others.

| top of page |

Listening to Music


07/04/2009

Page 29 of 62

The ScreenPlay Pro HD enables you to listen to music files in MP3, WAV, WMA, OGG, or M4A format. The ScreenPlay Pro HD also s DVD soundtracks in AC3 format (Dolby Digital Encoding), AAC, AIFF, and DTS. You can play music files through a TV set or connected amplifier/receiver. Follow the steps below to play music files. 1. Connect the ScreenPlay Pro HD to your computer and copy your music files onto the ScreenPlay Pro HD. You can also copy music files to the ScreenPlay Pro HD using a network connection or play music files directly from your home network or a USB device connected to the ScreenPlay Pro HD. NOTE: It is recommended that you create a folder for your music files rather than place them at the ROOT level. See Organizing your Multimedia Files for additional information. 2. Connect the ScreenPlay Pro HD to your TV. 3. Turn on your TV and change the input setting as needed to receive input from the ScreenPlay Pro HD. Refer to the manual that came with the TV if you are uncertain how to do this. 4. Activate the ScreenPlay Pro HD by pressing the STANDBY button on either the remote control or the front . NOTE: When using the remote control, always point it towards the receiver on the front of the ScreenPlay Pro HD. 5. Browse to the folder containing the music files you want to play (use the Up/Down buttons on either the remote control or the front to navigate through listed folders; press the ENTER key to open a folder or subfolder). 6. Select a music file and press the ENTER key or Play/Pause button to start playback. NOTE: While the music is playing, the playback seek slider will display on the TV screen. The title, performer, and the album information from the ID3 tag of an MP3 file will also display. 7. If you want to set music playback to repeat one file or all files in the folder, press the REPEAT key on the remote control sequentially to change to the desired mode:

Repeat 1—Repeats the current track 1 € Repeat all—Repeats all files in the folder in consecutive order all € Off—Playback stops automatically at the end of the selected track (default Off setting) €

Playlists


07/04/2009

Page 30 of 62

You can create playlists for your music and other media files using the Playlist Manager utility. To play back a Playlist, select it and press the Play button. A total of 2,048 files can be managed in a single Playlist.

| top of page |

Viewing Photo Images You can use the ScreenPlay Pro HD to create and view photo image slideshows. If desired, you can also add music to your slideshows. Follow the steps below. NOTE: The photo images must be in BMP or JPEG format, which is the format used by most digital cameras. The filename extension can be .bmp, .jpg, .jpe, or .jpeg. 1. Connect the ScreenPlay Pro HD to your computer and copy your photo images onto the ScreenPlay Pro HD. You can also copy photo images to the ScreenPlay Pro HD using a network connection or view photos directly from your home network or a USB device connected to the ScreenPlay Pro HD. NOTE: It is recommended that you create a separate folder or subfolder for each slideshow. Using the default settings, the ScreenPlay Pro HD will automatically display all of the images in a selected folder in alphanumeric order (for example, image01, image02, image03, etc.). See Organizing your Multimedia Files for additional information on creating folders and subfolders. 2. If you want to play music with your slideshow, copy the music tracks to the same folder or subfolder as the image files. Name the music tracks in the order you would like them to play, for example, track01, track02, track03, etc. NOTE: The filenames for the music tracks must list after all of the image files. When playing the slideshow, the ScreenPlay Pro HD will automatically start playing the first music track and continue to play each music track in alphanumeric order. You can use a maximum of 100 music files with each slideshow. 3. When you have finished copying the files you want to display, disconnect the ScreenPlay Pro HD from the computer. 4. Connect the ScreenPlay Pro HD to your TV. 5. Turn on your TV and change the input setting as needed to receive input from the ScreenPlay Pro HD. Refer to the manual that came with the TV if you are uncertain how to do this. 6. Activate the ScreenPlay Pro HD by pressing the STANDBY button on either the remote control or the front .


07/04/2009

Page 31 of 62

NOTE: When using the remote control, always point it towards the receiver on the front of the ScreenPlay Pro HD. 7. To set the display interval for your slideshow, press the SETUP key on the remote control to access the Setup menu. Select MISC > Slide Show Time, Time and select the time you want each photo to display. 8. Browse to the folder containing the photo images you want to view (use the Up/Down buttons on either the remote control or the front to navigate through listed folders; press the ENTER key to open a folder or subfolder). 9. Select the image file you want to start the slideshow, then press the ENTER key or Play/Pause button on the front . The ScreenPlay Pro HD will display all photo images in the folder consecutively with the selected display interval. NOTE: If you do not want to display the photos in slideshow mode, press the Play/Pause key on the remote control or front of the ScreenPlay Pro HD. You can then navigate through the photos manually by pressing the arrow keys. To return to slideshow mode, press the Play/Pause button again.

| top of page |

Using Playlist Manager A playlist is a collection of media files which can be played in series. The Playlist Manager utility included with the ScreenPlay Pro HD allows you to create playlists for your media files. Each playlist can contain only one media type (music, photos, or videos). Once you have created a playlist, you can play it back by selecting it and pressing the Play button on the front or remote control. A total of 2,048 files can be added to a single playlist. NOTE: A playlist is an .m3u file. In addition to playlists created using the Playlist Manager utility, the ScreenPlay Pro HD can use playlist files from other software players, such a Windows Media Play or Winamp. Follow the instructions below to create and manage playlists. 1. Connect the ScreenPlay Pro HD to your computer. 2. To launch the utility, Click Start€→ Iomega ScreenPlay Utility€→ Playlist Manager. Start Utility Manager 3. To create a new playlist, click the File menu and select New Playlist. Playlist The new playlist will appear in the lower window frame. Name the playlist as you wish. 4. To add files to your playlist, use the upper window to browse the media files stored on your ScreenPlay Pro HD. Select the files you want to use in your playlist and press the Add button.


07/04/2009

Page 32 of 62

5. To remove files from your playlist, use the lower window to browse and select files from the playlist, then press the Delete button. 6. To adjust the playlist sequence, select the files you want to manage and use the Up or Down button to move them a step forward or backward in the playlist. 7. Select the play mode you want to use with your playlist. There are three modes available:

Repeat One (1)—Play the first file repeatedly; press Next to repeat the next (1)

fiie. This mode is especially useful for presentations. € Repeat All—Play all files in normal mode and repeat the entire list after the last All

file has played. € Off—Playback stops automatically at the end of the selected track. Off €

Troubleshooting Tip: If a playlist does not appear on the TV when navigating the ScreenPlay Pro HD, open it on your PC using the Playlist Manager and save it again.

| top of page |

Recording TV Programs or Other Video Input You can record an audio/video signal from the TV or any other AV device connected to the composite input connectors on the ScreenPlay Pro HD. You can start recording immediately using the REC key on the remote control (one-touch recording), or you can schedule a recording to take place at another time. NOTES:

The AV source device must composite output in order to connect to the audio/video input connectors on the ScreenPlay Pro HD.

If the power supply is disconnected from the ScreenPlay Pro HD or there is a complete power outage, it will erase the recording schedule and you will need to reset the recording schedule when power is restored.

OneOne-touch Video Recording One-touch recording enables you to easily record TV programs without setting up a recording schedule. You can also use one-touch recording to record video from cameras, cable, or VCRs. Follow the instructions below. 1. Use the yellow connectors on the composite cable to connect video output from the TV set or other AV source device to the composite video input connector on the back


07/04/2009

Page 33 of 62

of the ScreenPlay Pro HD. 2. Use the red and white connectors on the composite cable to connect audio output from the TV or other AV source device to the RCA audio input connectors on the back of the ScreenPlay Pro HD, matching the colors of the jacks. 3. Turn on the TV or other AV input device. 4. Activate the ScreenPlay Pro HD by pressing the STANDBY key on the remote control. NOTE: When using the remote control, always point it towards the receiver on the front of the ScreenPlay Pro HD. 5. If you are recording a TV program, switch to the appropriate channel on the TV set. If you are recording from a camera or VCR, start video playback on the AV source. 6. Press the REC key on the ScreenPlay Pro HD remote control to start recording the AV input. 7. Press the REC key again to set up the recording length. NOTE: It is not necessary to set a recording length. In this case, manually stop the recording by pressing the STOP key on the remote control.

Recording TV Programs on a Schedule You can set up the ScreenPlay Pro HD to record your favorite TV programs or to record a special program you would otherwise not be able to watch. Follow the instructions below. NOTE: To display the ScreenPlay Pro HD menus on the TV screen, you need to connect the ScreenPlay Pro HD to video input on the TV. You will also need to connect video/audio output from the TV to the ScreenPlay Pro HD to provide the signal to record. 1. Connect video output from the ScreenPlay Pro HD to video input on the TV (see Connecting to a TV if you need instructions). 2. Use a composite cable to connect audio/video output from the TV to the audio/video input connectors on the back of the ScreenPlay Pro HD, matching the colors of the jacks. 3. Turn on your TV and change the input setting as needed to receive input from the ScreenPlay Pro HD. Refer to the manual that came with the TV if you are uncertain how to do this. 4. Activate the ScreenPlay Pro HD by pressing the STANDBY key on the remote control. NOTE: When using the remote control, always point it towards the receiver on the


07/04/2009

Page 34 of 62

front of the ScreenPlay Pro HD. 5. If you have not already done so, set the time clock on the ScreenPlay Pro HD. a. Press the SETUP key on the remote control or go to the ScreenPlay Pro HD Home menu and select Setup. Setup b. From the Setup menu, enter System > Time. Time c. Use the number keys on the remote control to enter the year (4-digit format), month (1-2 digits as needed), and day (1-2 digits). d. Enter the time in hours, minutes, and seconds on a 24 hour clock. NOTE: The time set on the ScreenPlay Pro HD must match that on the TV or set top box you want to record. e. Press the ENTER key on the remote control and confirm the time setting. 6. Return to the Setup menu and select REC. REC 7. Select Add a new schedule and press the ENTER key on the remote control. 8. Use the up and down arrow keys on the remote control to set the date and time you want recording to start. 9. Use the up and down arrow keys on the remote control to set the recording length in hours and minutes. 10. If you want to record this program more than once, set the Repeat option you want to use. 11. When you have finished setting up the record schedule, press the ENTER key on the remote control and confirm the schedule. 12. Before the record schedule runs, turn on the TV and switch to the channel you want to record. The ScreenPlay Pro HD will record the input AV signal as scheduled whether it is in Standby mode or activated for playback.

| top of page |

Viewing Recorded TV or Video The ScreenPlay Pro HD saves recorded TV programs or videos in a folder named REC. REC It automatically names the recorded video files according to the date and time at the beginning of the recording. The standard filename convention uses 8-digits to identify the


07/04/2009

Page 35 of 62

year, month, and day, followed by an underscore and 4-digits for the time on a 24-hour clock. For example, if you recorded a TV program that started at 7:00 p.m. on July 24, 2008, the filename for the recording would be 20080724_1900.mpg. 20080724_1900.mpg The ScreenPlay Pro HD uses MPEG-2 as the file format for all AV recordings. Use the following instructions to view an AV recording. 1. Connect audio/video out from the ScreenPlay Pro HD to the appropriate input connections on your TV. See Connecting to a TV if you need detailed instructions. 2. Turn on your TV and change the input setting as needed to receive input from the ScreenPlay Pro HD. Refer to the manual that came with the TV if you are uncertain how to do this. 3. Activate the ScreenPlay Pro HD by pressing the STANDBY button on either the remote control or the front . NOTE: When using the remote control, always point it towards the receiver on the front of the ScreenPlay Pro HD. 4. When the ScreenPlay Pro HD main menu loads, select ScreenPlay Pro and press the ENTER key on the remote control. 5. Select the REC folder and press the ENTER key. 6. Select the mpg file you want to view and press the ENTER key or Play/Pause button. Use the filenames to identify the program by the date and time it was recorded.

| top of page |

€


07/04/2009

Page 36 of 62

€ €

Setup Options

Using the Setup Menu

REC (Record)

Language

Network

Audio

System

Video

MISC

Using the Setup Menu The default configuration on the ScreenPlay Pro HD is compatible with most TV sets, so you might not need to use the Setup menu. If you need to change the ScreenPlay Pro HD configuration, refer to the information below on the setup menus, functions, and options. To access the Setup menu, press the SETUP key on the remote control, or select Setup from the ScreenPlay Pro HD HOME menu. To navigate through the Setup menu, use the up and down cursor keys to select a submenu or function and press the Enter key to display available options. To set the configuration for a function, use the up and down cursor keys to highlight the option you want to use, then press the Enter key to confirm the setting. To return to the list of functions, press the RETURN key on the remote control. You can also press the HOME key to jump to the ScreenPlay Pro HD main menu.

| top of page |

Language Menu Language Select the language used to display the ScreenPlay Pro HD menus. Text Encoding Use Unicode for all languages except Chinese. When viewing a video with Chinese subtitles, the text encoding must be set to match that used in the subtitle file. Audio Select the language for the default audio when playing a DVD movie. If the selected language is not ed by the DVD movie, the audio will default to English.


07/04/2009

Page 37 of 62

Subtitle Select the language for the default subtitle when playing a DVD movie. If OFF is selected, subtitles will not display during playback of DVD movies. NOTE: Some DVD movies do not subtitles and always default to off. Disc Language Select the language for DVD menus.

| top of page |

Audio Setup NOTE: You must stop playback to set options on this submenu. Speaker €

2 CH

Outputs stereo audio

€

5.1 CH

Select for use with Dolby Digital

Night Mode € €

€

OFF

Turns off night mode or the comfort option

ON

Decreases audio output through the ScreenPlay Pro HD to a soft level for nighttime listening

Comfort

Softens audio output only for sudden loud portions of an audio track

S/PDIF

€

€

€

€

€

HDMI LPCM*

Use with an HDMI connection. Outputs audio signal with multi-channel simulation whenever possible.

HDMI RAW

Use with an HDMI connection. Outputs digital audio without decoding.

SPDIF LPCM*

Use with a coaxial audio connection. Outputs audio signal with multi-channel simulation whenever possible.

SPDIF RAW

Use with a coaxial audio connection. Outputs audio signal with multi-channel simulation whenever possible.

*LPCM stands for Linear Pulse Code Modulation, Modulation which is a common method for encoding audio signal in CD and DVD.


07/04/2009

Page 38 of 62

| top of page |

Video Setup NOTE: You must stop playback to set options on this submenu. You must exit the Setup menu for settings on this submenu to take effect. Aspect Ratio

€

€ €

Pan Scan 4:3

Displays 16：9 images in “Pan and Scan” with a 4:3 ratio TV connected.

Letter Box 4:3

Displays 16：9 images in “Letter Box” with a 4:3 ratio TV connected.

16:9

Displays 16:9 images on a wide screen TV.

Brightness / Contrast

€

Adjust brightness and contrast settings for video output from the ScreenPlay Pro HD to the TV.

Video Output

€

€

Component

Outputs video signal via both composite and component connectors.

SCART

Outputs SCART RGB video signal via the composite output connector.

TV System €

NTSC

Outputs standard NTSC video signal

€

PAL

Outputs standard PAL video signal

€

480p

Use the 480p or 576p output

€

576p

resolution with a 4:3 ratio TV.

€

720p€50Hz

The 720p and 1080i options output

€

720p€60Hz

€

1080i€50Hz

€

1080i€60Hz

a 16:9 up-scaling video format for high definition wide-screen displays. Select the output option that optimizes display on the TV.


07/04/2009

Page 39 of 62

| top of page |

REC (Record) Setup Quality

Select desired recording quality: HQ, SP, LP, EP, or SLP

Auto Chapter

Set time for automatic chapter marker (15, 20, or 30 minutes) or turn off auto chapter markers.

| top of page |

Network Setup When the ScreenPlay Pro HD is connected to a network, the Network setup menu will display the IP address for either wired network with DH or wireless network. Wired LAN Setup

€

DH IP

IP address for the ScreenPlay Pro HD will be automatically assigned by the Network

Static IP €

Use to manually assign the IP Address, Subnet Mask, and Default Gateway used by the ScreenPlay Pro HD. Use number keys on the remote control to enter the desired addresses.

Wireless Setup Connect €

After setting up the wireless access point, use this option to automatically connect or reconnect the ScreenPlay Pro HD to the wireless network

Modify

Select to set up the wireless access point for the ScreenPlay Pro HD. Modify will automatically scan for available wireless

€

networks and allow you to set the and for the network you select. You can then configure settings for connection mode, wireless SSID, and wireless security.

| top of page |

System Setup Time

Set time clock used by ScreenPlay Pro HD

Restore Default

Select to restore all setup options to factory default settings


07/04/2009

Page 40 of 62

| top of page |

MISC (Miscellaneous) Setup Slide Show Timing

Set time to display each photo during slideshow

Transition Effect

Set fade or transition options for slideshow display

Background Music

Select playlist or folder containing music to play during slideshow

DIVX

Displays DivX registration number for use with DivX VOD

| top of page |

€


07/04/2009

Page 41 of 62

€ €

Troubleshooting

Problems on a TV Connection

Problems Playing Media Files

Problems on a Computer Connection

Problems on a Network Connection

Click the links below to expand or close the troubleshooting information. For help with problems that are not covered in this manual, please visit the area on www.iomega.com

Problems on a TV Connection TV screen does not display normally Press the TV SYS key on the remote control repeatedly until the screen displays normally. This toggles the video output on the ScreenPlay. See Setup Options > Video Setup > TV System for more information on video output settings.

| top of page |

TV screen rolls vertically This problem is probably due to an incorrect video output setting for your region. The selected setting must match your regional television standard (PAL or NTSC). To fix the problem, press the NTSC/PAL button on front of the ScreenPlay Pro HD to toggle the regional setting. NOTE: The default setting on the ScreenPlay matches the region where the device is purchased. You might see this problem if you travel and use your ScreenPlay in different parts of the world.

| top of page |


07/04/2009

Page 42 of 62

ScreenPlay Pro HD does not respond to the remote control

Make sure you are pointing the remote control directly at the receiver on the front . The orange LED on the ScreenPlay will flash when it receives a signal from the remote control. If the orange LED does not flash, make sure the ScreenPlay is receiving power (see ScreenPlay LEDs do not light), then check the following suggestions.

Make sure you have activated the ScreenPlay by pressing the STANDBY key on the remote control or front . When the ScreenPlay is activated, the blue LED on the front should blink for several seconds, then glow steadily.

If you are using the remote control for the first time, pull out the plastic tab to enable battery power.

Check the orientation of the battery in the remote control. The "+" side of the battery should be up.

If you have used the remote control for some time, the battery could be depleted. Refer to Replacing the Battery.

NOTE: If you select a function on the remote control that is not ed by the current menu or media file, the ScreenPlay will display a hand icon on the TV screen.

| top of page |

Blank or blue screen when the ScreenPlay Pro HD is connected to a TV

Confirm that the ScreenPlay Pro HD is correctly connected to the video input on your TV set. Refer to Connecting to a TV for detailed instructions.

Make sure the ScreenPlay Pro HD is connected to power, turned on, and activated.

Make sure you have selected the correct video input on your TV to display output from the ScreenPlay Pro HD.

The video output setting on the ScreenPlay might not be correct for your TV. Press the TV SYS key on the remote control repeatedly until the screen displays normally.

| top of page |

No audio output


07/04/2009

Page 43 of 62

Check the audio cable connection between the ScreenPlay Pro HD and the TV. The ScreenPlay Pro HD can be connected to RCA connectors on the TV using the red and white connectors on the included composite cable. You can also connect the ScreenPlay Pro HD to an AV amplifier (receiver) using a coaxial audio cable (not included). If you are using a composite RCA connection, be sure you have connected audio output from the ScreenPlay Pro HD to audio input on the TV set. NOTE: Some TV sets are equipped with separate composite and component audio inputs. Be sure that you have connected the correct one. See Connecting to a TV for instructions.

Check the Audio options on the Setup menu. If the ScreenPlay is connected to an AV amplifier using a coaxial cable, select the appropriate S/PDIF Output option for your equipment.

Check the volume setting on the TV or AV amplifier. You will not be able to hear audio if the volume is too low. Try pressing the volume increase key on the ScreenPlay Pro HD remote control.

The ScreenPlay Pro HD might be using the wrong audio channel. Press the AUDIO key on the remote control to select the correct audio channel.

| top of page |

TV does not have RCA jacks Try connecting your ScreenPlay Pro HD through a VCR or RF Modulator (the VCR needs to be in VCR mode rather than TV mode). You can also use the coaxial audio connector on the ScreenPlay Pro HD to connect to an AV amplifier (receiver) with a digital audio decoder (coaxial cable not included).

| top of page |

ScreenPlay LEDs do not light The blue LED glows whenever the ScreenPlay Pro HD is powered up (activated) and blinks when the ScreenPlay Pro HD is loading or accessing files. If the blue LED does not light, try the following troubleshooting suggestions.

Confirm that the power supply that shipped with the ScreenPlay Pro HD is corectly connected to the back of the drive. Try disconnecting and reconnecting the power supply cable.


07/04/2009

Page 44 of 62

Confirm that the power supply is connected to a working power outlet or uninterruptible power supply (UPS).

Check the connection of the power cord to the power supply.

The orange LED flashes to indicate receiving a signal from the remote control. If the blue LED is on but the orange LED does not flash, try the suggestions under ScreenPlay Pro HD does not respond to the remote control.

| top of page |

The Setup menu appears in the wrong language From the Setup menu, select Language > Menu Language and choose the language option you want to use. See Using the Setup Menu for instructions on how to navigate and select options on the Setup menu.

| top of page |

Problems Playing Media Files Media files are listed when connected to a computer but not on the TV

This happens if the media file format is not ed on the ScreenPlay. Refer to ed Media Formats for information on ed file types and filename extensions.

Make sure the folder containing the files is not compressed, encrypted, or hidden. You can check the folder attributes on a computer by right clicking on the folder icon and selecting Properties. Properties Make sure the box next to Hidden is not checked. Click the Advanced button to check whether or not the folder is compressed or encrypted.

| top of page |

Some media files will not play

Confirm that the file format is ed on the ScreenPlay. Refer to ed Media Formats for information on ed file types and filename extensions.

Make sure the file is not compressed.


07/04/2009

Page 45 of 62

Make sure the media file is not damaged. If available, try replacing the file with a known-good copy.

| top of page |

Movie audio or subtitle language does not change If the audio or subtitle language of a movie does not change when you press the SUBTITLE key on the remote control, it's likely that the movie has only one available language. Check the package specifications for the movie. If the movie includes different language options, make sure you are pointing the remote control directly at the receiver on the front of the ScreenPlay Pro HD and press the SUBTITLE key again. NOTE: If the hand icon appears on the TV screen when you press the SUBTITLE key, this function is not ed by the movie you are viewing.

| top of page |

Unrecognizable subtitle occurs when playing some DivX movies If the subtitle file is ANSI encoded text, you need to manually set the subtitle language option to match the language used by the subtitle file. Press the SETUP key on the remote control and select Language > Subtitle, Subtitle then choose the language you need.

| top of page |

Audio or subtitle is not in the selected language If the audio or subtitle on a movie does not come up in the language you have selected on the Setup menu, the movie probably does not include that language. Press the AUDIO or SUBTITLE keys on the remote control to select another language.

| top of page |

DVD menu behaves incorrectly - blank screen or repeated segments This happens if the DVD folder lacks some files needed for the menu function. To work around this issue, press the stop key on the ScreenPlay remote control to stop


07/04/2009

Page 46 of 62

playback, then select the VIDEO_TS file. Press the ENTER key to play the Main Title directly.

| top of page |

Problems on a Computer Connection ScreenPlay Pro HD does not appear or is not assigned a drive letter in My Computer or Windows Explorer

Try rebooting your computer.

Check all connections.

Make sure the ScreenPlay Pro HD is connected to power and turned on. The blue LED glows when the ScreenPlay Pro HD is powered up. If the LED is off, press the Standby button on the front of the ScreenPlay Pro HD to turn it on. The blue power/access LED will blink while the ScreenPlay Pro HD powers up, then glow steadily. If the blue LED does not light, see ScreenPlay LEDs do not light.

Make sure you are using the USB cable that came with the drive. If you are using a different cable, make sure it meets interface specifications.

Connect the USB cable directly to the port on the computer or on the USB card. Do not plug the drive's USB cable into a hub or keyboard.

If you are using a USB 2.0 host adapter, make sure that the correct drivers for the adapter have been installed and the operating system recognizes it.

Check your BIOS to ensure USB is enabled. Please refer to your computer's 's guide or manual for instructions.

If the drive is still not assigned a drive letter, please visit the area on www.iomega.com.

| top of page |

ScreenPlay Pro HD performance seems slow connected to USB

To help avoid this problem, make sure other USB devices are not being used at the same time as the ScreenPlay Pro HD. Other devices that can affect performance include digital cameras, scanners, and other high-speed peripherals that process large amounts of data.


07/04/2009

Page 47 of 62

Connect the data cable directly to the port on the computer or on the USB card. Do not plug the drive's data cable into a hub or keyboard. NOTE: The ScreenPlay Pro HD will perform slower when connected to a standard USB 1.1 port. The drive will not reach the maximum transfer rate unless it is connected to a USB 2.0 port. For additional information B 1.1 and 2.0 and how to determine which version is installed on your computer, please visit the area of www.iomega.com.

If drive performance still seems slow, please visit the area of www.iomega.com for additional troubleshooting.

| top of page |

Large files will not copy to the ScreenPlay Pro HD If the ScreenPlay Pro HD is formatted FAT32, an individual file that is 4GB or larger cannot be copied due to limitations in the FAT32 file system. If you have a file that is 4 GB or larger, try using a compression utility to make the file smaller. If you can compress it to less than 4GB, you will be able to copy it to a FAT32 volume. NOTE: The ScreenPlay Pro HD must be formatted either NTFS or FAT32 in order to play back media files on a TV.

| top of page |

ScreenPlay Pro HD locks up, freezes, or information gets lost or corrupted The problem is probably due to a non-compliant USB controller chip or other devices on your computer system. Try the following suggestions:

Carefully follow the USB guidelines. They are designed to help you avoid some of the problems caused by non-compliant USB devices.

If the problem persists, you may want to upgrade the USB controller in your computer system to one that complies with the latest USB specification. In this case, your computer manufacturer for help.

Do not disconnect the Iomega drive while it is transferring information. Data loss will result!

Do not connect or disconnect other USB devices while the Iomega drive is transferring information. Data loss will result!


07/04/2009

Page 48 of 62

If the computer still locks up, freezes, or information gets lost or corrupted, please visit the area of www.iomega.com for additional troubleshooting. CAUTION! USB devices (including cards, mice, joysticks, and peripherals) that do not comply with the USB specification may cause system lockups or possible data loss when used with the Iomega drive. If you are not sure that a USB device complies with the latest USB specification, the manufacturer of the device.

| top of page |

Windows stops responding when you disconnect the ScreenPlay Pro HD This may occur because Windows is trying to access a file that is on the ScreenPlay Pro hard drive. Make sure that none of the files on the disk are open when you unplug the drive. Be sure to stop the drive before disconnecting the data cable or power cable from the drive to prevent any data loss.

| top of page |

Problems on a Network Connection ScreenPlay Pro HD is not recognized on the network

Make sure the ScreenPlay Pro HD is connected to power and turned on. The blue LED glows when the ScreenPlay Pro HD is powered up. If the LED is off, press the Standby button on the front of the ScreenPlay Pro HD to turn it on. The blue power/access LED will blink while the ScreenPlay Pro HD powers up, then glow steadily. If the blue LED does not light, see ScreenPlay LEDs do not light.

If you are using a wired network connection, check the following:

Make sure you are using a functional Ethernet cable. that the LED on the Ethernet (LAN) connector is lit.

Make sure the Ethernet cable is connected to a 10/100Base-T switch, hub, or router, or directly to a computer on the network.

Check all connections (power and network).

If you are using a wireless network connection, check the following:

Make sure you are using a ed WiFi adapter. Check the area on www.iomega.com for the latest information on ed WiFi


07/04/2009

Page 49 of 62

adapters.

Make sure the WiFi adapter is securely connected to the USB host port on the back of the ScreenPlay Pro HD drive. You should see a message on the ScreenPlay Pro HD TV display indicating Wifi plug-in.

Make sure you have set up the wireless access point for the ScreenPlay Pro HD. See Connecting to a Wireless Network for instructions.

Wait a few minutes and then try connecting to the ScreenPlay Pro HD again. See Connecting to the ScreenPlay Pro HD from a Networked Computer for detailed instructions.

Try rebooting your computer and connecting to the ScreenPlay Pro HD again.

Make sure the computer you are using to connect to the ScreenPlay Pro HD is on the same subnet or network segment as the ScreenPlay Pro HD.

| top of page |

Where is the IP address for the ScreenPlay Pro HD? The ScreenPlay Pro HD uses DH by default and will be automatically assigned an IP address by the network. To view the IP address, go to the ScreenPlay Pro HD Home menu on the TV display, select Setup > Network. Network The IP address will appear next to the network connection you are using (wired LAN or wireless). If the IP address does not appear, make sure the ScreenPlay Pro HD is correctly connected to the network (see ScreenPlay Pro HD is not recognized on the network).

| top of page |

Unable to enter network on the ScreenPlay TV display If you need to enter a name and to to a network volume, press the ENTER key on the remote control. This will bring up a virtual keyboard on the ScreenPlay Pro HD TV display. Use the remote control cursor keys and the ENTER key to select the necessary characters. The ScreenPlay Pro HD virtual keyboard s any combination of numbers, lower case letters, upper case letters (caps), periods, and slashes. It does not extended punctuation characters (such as !, @, #, $, %, &, etc.). If you need to logon to a network volume that uses a strong , change the to use only characters ed by the ScreenPlay Pro HD virtual keyboard.


07/04/2009

Page 50 of 62

| top of page |

€


07/04/2009

Page 51 of 62

€ €

How to Get Help Iomega is committed to providing excellent customer . To meet this goal, Iomega offers a variety of options designed to meet the needs of a wide range of s. For complete information on the options available for your Iomega product, check our website at www.iomega.com. Please select your region carefully. Here's just some of what is available on Iomega's award-winning web site 24 hours a day, 7 days a week:

Answers to frequently asked questions (FAQs)

Online help pages with troubleshooting or basic "how to" information

Up-to-date Iomega software and drivers

Advanced online options, such as 1-on-1 live chat and email

Electronic copies of Iomega product manuals

Information on telephone options

Information on advanced technical service options, such as data recovery

Warranty information and product return instructions

options available may vary depending on your region and language of choice. NOTE: Iomega's specific customer policies (including fees for services) and procedures change as technology and market conditions dictate. To obtain information about Iomega's current policies, please visit our website or write to: Iomega Customer Service, 4059 South 1900 West, Roy, UT 84067, USA.

| top of page |

€


07/04/2009

Page 52 of 62

€ €

Limited Warranty — U.S. and other nations (Drives and Media)

Coverage

Excluded Products and Problems

Remedies

Obtaining Warranty Service

Limitations

Coverage Iomega warrants this hardware product to be free from defects in materials and workmanship for the warranty period. This non-transferable, limited warranty is only to you, the first end- purchaser. The warranty begins on the date of purchase and lasts for the period specified below: ®

REV, REV Pro, and Zip drives: one (1) year

REV, REV Pro, and Zip disks: five (5) years

Desktop Hard Drives: one (1) year

Portable Hard Drives: one (1) year

ScreenPlay Multimedia Players and ScreenPlay TV Link: one (1) year

Home Network Drives: one (1) year

StorCenter Network Drives: one (1) year

Iomega CD-RW and DVD drives: one (1) year

All Iomega reconditioned products: ninety (90) days

Any other Iomega hardware product unless otherwise stated: one (1) year

®

| top of page |

Excluded Products and Problems This warranty does not apply to: (a) Iomega software products; (b) expendable components such as fuses or bulbs; or (c) third party products, hardware or software, supplied with the warranted product. Iomega makes no warranty of any kind on such products which, if included, are provided "AS IS." This warranty also excludes damage caused by accident, misuse, abuse, use of non-Iomega approved media, exposure of media to excessive magnetic fields, or external environmental causes. Remedies


07/04/2009

Page 53 of 62

Your sole and exclusive remedy for a covered defect is repair or replacement of the defective product, at Iomega's sole option and expense (shipping may be charged), and Iomega may use new or refurbished parts or products to do so. If Iomega is unable to repair or replace a defective product, your alternate exclusive remedy shall be a refund of the original purchase price. The above is Iomega's entire obligation to you under this warranty. IN NO EVENT SHALL IOMEGA BE LIABLE FOR INDIRECT, INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES OR LOSSES, INCLUDING LOSS OF DATA, USE, OR PROFITS EVEN IF IOMEGA HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. In no event shall Iomega's liability exceed the original purchase price of the drive or the media disk. Some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.

| top of page |

Obtaining Warranty Service You must notify Iomega within the warranty period to receive warranty service. Just as technology and market conditions vary, Iomega’s specific customer policies (including fees for services) and procedures change over time. To obtain information about Iomega's current policies or warranty service, please visit our website at www.iomega.com/policy.html or write to: Iomega Customer Service, 4059 South 1900 West, Roy, UT 84067, USA. Limitations THE ABOVE WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED. To the extent permitted by applicable law, IOMEGA SPECIFICALLY DISCLAIMS ANY IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Any implied warranty required by applicable law shall be limited in duration to the express warranty term. Some jurisdictions do not allow disclaimers of implied warranties or limitations on how long an implied warranty lasts, so the above limitation may not apply to you. This warranty gives you specific legal rights and you may also have other rights that vary from jurisdiction to jurisdiction. Any suit for breach of any warranty on your product must be filed within one (1) year of the first date the suit could have been brought.

| top of page |

€


07/04/2009

Page 54 of 62

€ €

Limited Warranty — Europe, the Middle East, and Africa (Drives and Media)

Coverage

Excluded Products and Problems

Additional Excluded Problems for NAS (Network Attached Storage) Products

Remedies

Obtaining Warranty Service

Limitations

Coverage Iomega warrants this hardware product to be free from defects in materials and workmanship for the warranty period. This non-transferable, limited warranty is only to you, the first end- purchaser. The warranty begins on the date of purchase and lasts for the period specified below: ®

REV, REV Pro, and Zip drives: two (2) years

REV, REV Pro, and Zip disks: five (5) years

Desktop Hard Drives: two (2) years

Portable Hard Drives: two (2) years

ScreenPlay Multimedia Players and ScreenPlay TV Link: two (2) years

Home Network Drives: two (2) years

StorCenter Network Drives: two (2) years

Iomega CD-RW and DVD drives: two (2) years

Any other Iomega hardware product unless otherwise stated: two (2) years

®

Excluded Products and Problems This warranty does not apply to: (a) Iomega software products; (b) expendable components such as fuses or bulbs; or (c) third party products, hardware or software, supplied with the warranted product. Iomega makes no warranty of any kind on such products which, if included, are provided "AS IS." This warranty also excludes damage caused by accident, misuse, abuse, use of non-Iomega supplied or approved media, exposure of media to excess magnetic fields, or external environmental causes. Additional Excluded Problems for NAS (Network Attached Storage) Products With respect to NAS products, this warranty also does not apply to: (a) any improper use and/or application of the NAS product, including any non-observance of instructions given


07/04/2009

Page 55 of 62

in the owner's manual and/or service manual by any person—including, without limitation, application of abnormal shock, improper supply voltage, exposure to abnormal temperature or improper handling of the NAS product; or (b) any alteration, change, modification or repair made on the NAS product by any party other than Iomega or its authorized service centers. Remedies Your sole and exclusive remedy for a covered defect is repair or replacement of the defective product, at Iomega's sole option and expense (shipping may be charged), and Iomega may use new or refurbished parts or products to do so. The replaced part/product will be warranted for the remainder of the original warranty or three (3) months from the date of shipment of such parts/products, whichever is longer. If Iomega is unable to repair or replace a defective product, your alternate exclusive remedy shall be a refund of the original purchase price. The above is Iomega's entire obligation to you under this warranty. IN NO EVENT SHALL IOMEGA BE LIABLE FOR INDIRECT, INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES OR LOSSES, INCLUDING LOSS OF DATA, USE, OR PROFITS EVEN IF IOMEGA HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. In no event shall Iomega's liability exceed the original purchase price of the drive or the media disk. Some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.

| top of page |

Obtaining Warranty Service You must notify Iomega within the warranty period to receive warranty service. Information for Iomega Customer Service can be obtained on our website at www.iomega.com/europe/. If the Iomega representative determines your product is eligible for warranty service, you will be required to return it to Iomega, along with proper identification, a return authorization number provided by the representative, and proof of purchase. Iomega will not protect, recover, or return data during warranty service so you should duplicate your data before shipment. Just as technology and market conditions vary, Iomega’s specific customer policies (including fees for services) and procedures change over time. To obtain information about Iomega's current policies or warranty service, please visit our website at www.iomega.com/policy.html or write to: Iomega Customer Service, 4059 South 1900 West, Roy, UT 84067, USA. Limitations THE ABOVE WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED. To the extent permitted by applicable law, IOMEGA SPECIFICALLY DISCLAIMS ANY IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Any implied warranty required by applicable law shall be limited in duration to the express warranty term. Some jurisdictions do not allow disclaimers of implied warranties or limitations on how long an implied warranty lasts, so


07/04/2009

Page 56 of 62

the above limitation may not apply to you. This warranty gives you specific legal rights and you may also have other rights that vary from jurisdiction to jurisdiction. Any suit for breach of any warranty on your Product must be filed within 1 year of the first date the suit could have been brought. This warranty contains information on the options available at the time it was prepared. For up-to-date information, please the Iomega website at www.iomega.com/europe/.

| top of page |

€


07/04/2009

Page 57 of 62

€ €

Regulatory Information FCC (United States) The computer equipment described in this manual generates and uses radio frequency (RF) energy. If the equipment is not installed and operated in strict accordance with the manufacturer's instructions, interference to radio and television reception might result.

This equipment complies with Part 15 of the FCC Rules. Operation is subject to the following conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Part 15, Class B, of the FCC Rules, is designed to provide reasonable protection against radio and television interference in a residential installation. Although the equipment has been tested and found to comply with the allowed RF emission limits, as specified in the above cited Rules, there is no guarantee that interference will not occur in a particular installation. Interference can be determined by turning the equipment off and on while monitoring radio or television reception. The may be able to eliminate any interference by implementing one or more of the following measures:

Reorient the affected device and/or its receiving antenna.

Increase the distance between the affected device and the computer equipment.

Plug the computer and its peripherals into a different branch circuit from that used by the affected device.

If necessary, consult an experienced radio/television technician for additional suggestions.

NOTE: Changes or modifications to the electronics or enclosure of this product must be expressly approved by Iomega; otherwise, the 's authority to operate this product might be voided by the FCC.

For USA – California Only This product contains a CR Coin Cell Lithium Battery which contains Perchlorate material – special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate. | top of page |


07/04/2009

Page 58 of 62

Canadian Verification This Class B digital apparatus meets all requirements of the Canadian InterferenceCausing Equipment Regulations (ICES-003, Class B).

| top of page |

CE (European Community) This Iomega product conforms to the following European Directive(s)and Standard(s): Application of Council Directives: 73/23/EEC, 89/336/EEC. Standards to which Conformity is declared: EN60950, EN55022, EN55024, EN61000-3-2, EN61000-3-3. Importer's Name: Iomega International, S.A. Type of Equipment: Information Technology Equipment.

| top of page |

Waste Electrical and Electronic Equipment (WEEE)

In accordance with European Directive 2002/96/EC on Waste Electrical and Electronic Equipment (WEEE), the presence of the above symbol on the product or on its packaging indicates that this item must not be disposed of in the normal unsorted municipal waste stream. Instead, it is the ’s responsibility to dispose of this product by returning it to a collection point designated for the recycling of electrical and electronic equipment waste. Separate collection of this waste helps to optimize the recovery and recycling of any reclaimable materials and also reduces the impact on human health and the environment. For more information concerning the correct disposal of this product, please your local authority or the retailer where this product was purchased.

Manufacturer/Responsible Party Iomega Corporation 4059 South 1900 West Roy, UT 84067 USA


07/04/2009

Page 59 of 62

| top of page |

€


07/04/2009

Page 60 of 62

€ €

Using This Manual Expanding Submenu Topics In the left hand menu, click a plus sign€€ €€to reveal the submenu topic links. If there is no plus sign next to the title, there are no submenu links. Click the minus sign to hide the submenu.

Expanding Page Topics Some pages show a list of topics in blue text. Click a topic to show the information. Click the topic again to collapse the topic.

Using the Search Feature

Type a word or subject in the search box at the top of the page

,

then click the magnifying glass icon to quickly locate specific information. You must type three or more letters for the search function to work. If you type two words in the search box, such as "Windows format", the search will locate topics that contain either "Windows" or "format". Advanced Search To search for a specific phrase or group of words, enter a "+" (plus) sign followed by the word or phrase you want to locate. When using the plus sign, do not leave any space between it and the query string. The search will then bring up topics that have all the words in the search query. Example: "+Windows format" will search for topics that contain both "format" and "Windows".

Printing Click the Print icon

at the bottom of the menu to print the current page.

Click the Print Manual icon

(Internet Explorer for Windows and Apple Safari only) at the

bottom of the menu to print the entire manual.


07/04/2009

Page 61 of 62

Mac s: Click the Print or Print Manual button to open the page in a new window (without the banner and navigation bar), then select Print from your browser menu.

| top of page |

€


07/04/2009

Page 62 of 62

€ €


07/04/2009

Manual Iomega Screenplay Pro Hd 3s4i3x

Overview 5o1f4z

More details 6z3438

Related Documents c2h70

Manual Iomega Screenplay Pro Hd 3s4i3x

Ishowu Hd Pro Manual 6n5d3e

Iomega Screenplay Tv Link Hd Media Player - Inmac 3h2t4

Iomega Storcenter Pro Nas 150d 1q64j

Toshiba Camileo Pro Hd Manual 544d2g

Iomega s Manual j3m1p

More Documents from "Miguel Angel Luque Nieto" 6c83f

Manual Iomega Screenplay Pro Hd 3s4i3x

Torno Vertical Y Cnc 3p125g

1-operaciones Metalurgicas 6p4ix

6g3p1u

Paper1.pdf 4166g

Amplificador Diferencial Con Transistores Bjt 6o4m3i