Wind Load Ns 2010 Sample 4n3y37

An example problem on wind load calculation according to NS 2010 ;) A 20-meter-high square-plan five-storey building with flat roof and 4m-high floors, located in Makati CBD, has sides of 10 meters length each, and a large open front door on the first floor that is 2m x 2m in dimension. Assuming that G = 0.85 and that torsion is negligible, 1. Show how this maybe is an open, partially enclosed, or enclosed building. 2. Determine the internal pressure coefficients. 3. Determine the external pressure coefficients for the design of main girders and shear walls. 4. Determine the base reactions due to along-wind loads acting on the front wall of the building. 1. The building satisfies all definitions of a partially enclosed building (NS 2010 Section 207.2). 2. The internal pressure coefficients for a partially enclosed building (Gi) are +/- 0.55 (NS Figure 207-5). 3. The external pressure coefficients on MWFRS (from NS 2010 Figure 207-6) are as follows: - windward wall, = 0.8 - leeward wall, = -0.5 since L = 10m, B = 10m, and L/B = 1 - side walls, = -0.7 - whole roof, = -1.04 or -0.18 since h = 20m, h/L = 2, L <= h/2 = 10m, and Roof Area = 100 sq.m > 93 sq.m 4. The base reactions can be calculated after we calculate the design wind force at each level. However, taking x = alongwind direction, y = across-wind direction, z = vertical direction, we already can deduce that Vy = 0, and Mx = 0. Additionally, Mz is given as zero. We only need to estimate Vx, Vz, and My. To calculate the design wind force at each level, we need to multiply net design wind pressures at each level with tributary areas. To get net design wind pressures, we calculate pressures on both windward and leeward faces. On each face, we need to calculate the net of external and internal pressures. To get external and internal pressures, we need first to calculate the velocity pressures at each level. To calculate by hand, it is easiest to do this in table form but with a computer, a spreadsheet makes it much easier:

Assume: Exposure Terrain Category B Case 2, Iw = 1.0, Kd = 0.85, Kzt = 1.0, V = 200 kph Windward wall pz (kPa) Leeward wall pz (kPa) z (m) Kz qz (kPa) with +Gi with -Gi with +Gi with -Gi 20 0.88 1.42 0.18 1.75 -1.38 0.18 16 0.82 1.32 0.12 1.68 -1.38 0.18 12 0.76 1.22 0.05 1.61 -1.38 0.18 8 0.67 1.08 -0.05 1.52 -1.38 0.18 4 0.57 0.92 -0.16 1.41 -1.38 0.18 0 0.57 0.92 -0.16 1.41 -1.38 0.18 Net along wind pressures Net along wind loads Fz pz (kPa) (kN) Afz (sqm) with +Gi with -Gi with +Gi with -Gi 1.56 1.57 20 31 31 1.5 1.5 40 60 60 1.43 1.43 40 57 57 1.33 1.34 40 53 54 1.22 1.23 40 49 49

Base bending moment contribution My,z (kNm) with +Gi with -Gi 620 620 960 960 684 684 424 432 196 196

1.22

Af,roof (sqm) 100

1.23

20 Vx (kN) =

24 274

25 276 My (kNm) =

0

0

2884

2892

Roof loads 1, p Roof loads 2, p Vz = Roof Vz = Roof (kPa) (kPa) loads 1 (kN) loads 2 (kN) with with with with with with with with +Gi -Gi +Gi -Gi +Gi -Gi +Gi -Gi -2.04 -0.47 -1 0.56 -204 -47 -100 56 Vz (kN) = -204 56

strife ronjiedotcom

•

4 months ago

thank you sir..so, how about if its a truss analysis? where should i start my computation sir? with reference to the Ns..im at a lost in wind load computations.  ronjiedotcom

Mod

strife • 4 months ago

For vertical truss structures, wind forces are always applied horizontally. For roof trusses, they are applied perpendicular to the surface receiving the wind pressures.  •



in reference with NS sir,wat is the equation to use for the wind load acting on a truss alone? And also In staad, Can i consider a single truss only considering loads(dead,live,wind) in tributary area?! 

The answer to your first question is in the NS. For any structural analysis whether using STAAD or another software, of course you can consider a single truss considering only the tributary area but make sure to use the appropriate loads for that area. What did you need this for? A homework or a project? strife ronjiedotcom

•

4 months ago

or formula (207-15): Qh=.0000473*Kz*Kzt*Kd*Iw*V^2?  strife ronjiedotcom

•

4 months ago

for a project sir. im considering loads acting on a truss alone and not on d whole structure..in what part of the ns will i refer to directly? if wimd velocity is 350kph. can i use ds formula (207-22): p=Qh[(G) - (Gi)] to directly act normally to the roof? 

•

guest ronjiedotcom • 4 months ago for a project sir. can i use fig. 207-1 in the computation of wind load and apply it to the truss considering only the tributary area? ce_1

•

5 months ago

Good day sir! Im a bit confused. Can you show me how the wind pressure o

ronjiedotcom

Mod

ce_1 • 5 months ago

Hi, can I show you how the wind pressure.....? ferds

•

a year ago

Good day sir. do you have a sample problem like above to get the roof wind load for sawtooth type of buildings? ronjiedotcom

o

Mod

ferds • a year ago

I don't have one, but I think the NS's figures for sawtooth roofed buildings is prettystraightforward. Thanks for commenting! Engineer1

•

a year ago

Hi ronjie, do you know where Table 207-11 is located in NS 2010? •  ronjiedotcom

Mod

Engineer1 • a year ago

Thanks, I think I do. How about you?  Engineer1 ronjiedotcom

•

a year ago

I have trouble finding it yesterday, it seems that the code has some typo graphical errors in sec. 207.7.1 which directs you to table 207-11. Table 207-11 does not exist but the intended content of table 207-11 is available in table 207-5. Additional info. Eqn 207-38 & 207-39 is equal to 0.016/h and 0.23/h respectively. however Eqn 207-40 is equal to 0.007/n, in which h = ht of structure, and n = natural freq of structure. are Eqns 207-38 & 207-39 correct? or h should be replaced by n? 1 ronjiedotcom

Mod

Engineer1 • a year ago

Yeah, thanks for pointing that out. I've started to use the latest NS only recently and I've also spotted a lot of typographical errors already. You are right, Table 207-11 should be Table 207-5, and note also that alpha-overbar and a small letter "L" in Times New Roman are mentioned in 207.7.1 but in Table 207-5, it's actually A-overbar and a small letter "L" in script font in there. There are also a number of instances where h or h <= 18 m or h >= 18 m appears to have been omitted. As to your question on Equations 207-38, -39, and -40, note that 207-38 and -39 are formulas for one thing (Beta_s), while 207-40 is a formula for another thing (Beta_a). I think that is quite clear, so my answer to your question is: no, h should not be replaced by n. 

jelliepish

•

a year ago

Sir, pare-pareho lang po ba talaga ung values ng Leeward wall pz sa kahit anong elevation? Thank you po in advance. :) ronjiedotcom

Mod

jelliepish • a year ago

NS 2010 Figure 207-6 answers your question. :)  •

a year ago

Oh. Thank you so much Sir! :D 

Good Day Sir! We're currently deg a building for a project and I hope it's okay to ask some concerns regarding the NS code. The one that would be designed here is the MWFRS part of the bldg. The building is a low rise type and the calculations will be done using the Method 1 based from NS 2010. It is said that Method 1 is applicable to both gable type and flat roof type buildings. The one indicated on Figure 2 of NS is a gable type building where there are loads A,B,C,D,E,F,G,and H applied. a.) What will happen to the loads B and D for flat roof type of buildings? According to the table provided by NS there are negative horizontal pressures on these zones but since the eave height is equal to the height of the structure, i think B and D should be zero. | b.) Will there be no pressure applied on the rear side of the building? ronjiedotcom

Mod

Guest • a year ago

Adolfo, thanks for asking. I can't help but notice two things... 1. "WE... deg a building"? You have a license already? ;) 2. "NS code"... National Structural Code of the Philippines Code? :D As to your two questions, reading the NS, I think it's quite clear what the answers are. As I have emphasized in class, just make sure to consider at least 4 wind directions. Good luck! Engineer1

•

2 years ago

Hi, Ronjie. How would you evaluate the pressure coeff. for structures with irregular polygon shapes, say a structure with a plan shape of the letter "W" or "k". Most of the pressure coefficients in the code are for uniform section such as Circle, rectangle, square, etc. I have my own approach on this (mostly based on engineering judgement), but I would like to hear first on a wind load aficionado, such as yourself. ronjiedotcom

Mod

Engineer1 • 2 years ago

John, thanks for your question. You are right, codes usually do not provide for such rather uncommonly used building shapes. You can of course use engineering judgment based on the coefficients for shapes given in the code, which are based on wind tunnel tests on those specific "regular" shapes. That said, the more accurate and most rational method is to use the wind tunnel approach (i.e. Method 3 in NS 2010, or ASCE7). Unless it is a shape that has been tested before and is published in literature, you might not be ing for unexpected wind flow patterns that could increase wind pressures at specific locations, or you might not be realizing cost savings by using a more accurate approach. If you are dealing with tall buildings, it is easy to justify the relative low cost of doing a wind tunnel test. John Philip Cabañero

•

2 years ago

Sir, diba yung roof pressure coefficient value must be multiplied by 0.80 to for its area? So -0.18 should be -0.144? :) o ronjiedotcom

Mod

John Philip Cabañero • 2 years ago

The NS 2010 appears to say that the 0.8 reduction factor for area should be applied only to -1.3 and not to -0.18. The NS 2001 did not specify a -0.18 coefficient but it did say that the reduction factor applies only to the -1.3 coefficient. John Philip Cabañero ronjiedotcom

Thanks, sir!

•

2 years ago