Shurt 2011 Catalog 3rg5o

Contents Section 1

Grooved Mechanical Couplings, Flange Adapters & Mechanical Tees Section 2

Cast & Wrought Grooved Fittings

Section 3

Stainless Steel Series

Section 4

Valves & Flow Control Components

Section 5

Threaded Fittings & Welding Outlets

Section 6

Ring t, Shouldered & Plain-end Couplings

Section 7

HDPE Series

Section 8

Copper Series

Section 9

AWWA Ductile Iron Series Connect with the Best! Section 10

Catalog 2011

www.shurt.com

Technical Information

General Information Foreword......................................................................................................3 Ductile Iron...................................................................................................4 Bolts and Nuts..............................................................................................5 Gaskets........................................................................................................6 Pressure -Temperature Ratings, Service Temperatures and Vacuum Service............................................................................................8 Standards and Codes.................................................................................10

General Notes 1. Always read and understand all Shurt installation instructions before installing any Shurt product.

2. Always depressurize and drain the piping system before attempting disassembly, adjustment or removal of any piping components. 3. Designers must know and understand all relevant building and or piping standards, codes and specifications. It is the responsibility of the designer to select and or specify the appropriate product for the intended use and service. 4. Always refer to the maximum pressure rating and service temperature range allowed for Shurt products and ensure that they are used within these parameters.

5. Special attention is required for selection of suitable gasket grades for the intended service application.

6. All information and data contained herein supersede all previous published data. Shurt reserves the right to change product designs and or specifications without notice and or obligation. Please refer to the Shurt web site for the latest information.

Connect with the Best!

Catalog 2011

© Copyright 2011 Shurt

www.shurt.com

Catalog 2011


Shurt A World Leader in Mechanical Piping Components

Mechanical couplings were first developed in the 1920's and evolved into Grooved Mechanical Couplings during the 1950's & 60's. This revolution was further spurred in the latter half of the 20th century by advanced engineering and innovative materials such as Ductile Iron and EPDM elastomers.

Typical Applications

Past to Present The history of

Shurt dates back to 1974, when the founders produced their first grooved couplings. These first couplings were produced from malleable iron, the casting material of choice at this time. Before long foundry production was converted to ductile iron. Ductile iron was the ideal material, providing for precision castings and superior strength, without the need for further heat treatment. EPDM (ethylene propylene diene monomer) provided a great advancement in synthetic rubber elastomer compounds. This new compound offered a service life equal to or in some cases longer than that of carbon steel pipe. EPDM was an ideal gasket material for grooved piping systems.

A World Leader With nearly four decades of experience, Shurt is recognized as a world leader in the design and manufacture of mechanical piping components. Shurt has developed and currently offers over 3000 individual piping components in sizes from ½” to 96”, for use with a variety of piping materials including carbon steel, stainless steel, ductile iron, PVC, HDPE, VC and copper tubing.

The Shurt Mission Our

mission is to supply the highest quality products to customers worldwide with an unmatched level of customer service at a superior value. In addition to these hallmarks, Shurt continuously invests in research, engineering and development, resulting in innovative products and new solutions for the changing needs of industry.

The Shurt Cata this 2011 catalog we are incorporating the ASME/ANSI pressure & temperature rating method. Thus allowing you to select, specify and procure Shurt piping components in the same manner and method that you do with other fittings, flanges, valves, pumps and other components. Shurt encourages engineers and designers to use this classic and practical pressure rating system when using grooved mechanical components in place of or in conjunction with traditional pipe ing methods.


HVAC

Reverse Osmosis

Fire Protection

Desalination

Water Supply & Treatment

Mining & Tunnel Boring

Plumbing

Marine

Municipal

Gas

Food Processing

Chemical

Pulp & Paper

Oil

Agriculture

Air

Taipei 101, 509.2M, the world tallest building 2004 - 2010

www.shurt.com

3 ©Copyright 2011 Shurt

Catalog 2011

Ductile Iron – Housing Material

ASTM A536, Grade 65-45-12 (UNS F33100)

Chemical Requirements* Minimum Carbon, % 3.0 Silicon, % 2.5 Manganese, % 0.1 Phosphorus, % Sulfur, % Magnesium, % 0.03 Chromium, % Physical Properties

Tensile strength, psi (MPa) 65,000 (448) Yield strength, psi (MPa) 45,000 (310) Elongation, % 12

Maximum 3.9 3.0 0.4 0.07 0.02 0.05 0.1

Ductile iron is an ideal material for grooved mechanical components, as it provides similar or greater strength to that of wrought or cast steel piping materials such as; forged steel flanges - ASTM A105, carbon steel valves - ASTM A216 WCB, wrought carbon steel pipe - ASTM A53 Gr. B, etc. Most Shurt components are made of ductile iron conforming to ASTM A536 Gr. 65-45-12 and or ASTM A395 Gr. 65-45-15.

*Reference only as chemical requirements are not specified in ASTM A536.

Ductile iron was first invented in the U.S.A. and U.K. in the late

ASTM A395, Grade 65-45-15 (UNS F33100)

1940's. Superior strength was achieved by crystallizing graphite in

Chemical Requirements Minimum Carbon, % 3.0 Silicon, % Manganese, % Not specified Phosphorus, % Sulfur, % Not specified Magnesium, % Not specified Chromium, % Not specified Physical Properties

Tensile strength, psi (MPa) Yield strength, psi (MPa) Elongation, %

the shape of nodules. The result was ductile iron that had tensile and yield strength properties that were equal to or greater than some steel castings. This superior strength combined with ductile irons excellent castability helped to reduce the weight and cost of many components. Because of these advantages and benefits, many components have been converted from gray iron, malleable iron and steel castings to ductile iron over the past 60 years. Please visit the Ductile Iron Society website; www.ductile.org, for further information.

Sand supply unit

-------

Maximum 2.5 0.08

65,000 (448) 45,000 (310) 15

-------

Disamatic Molding Line Max. 360 molds per hour

Pattern plate change unit Ductile Iron Superior tensile strength with good castability

Gray Iron Excellent castability but ‘brittle’ – less strength

Malleable Iron Stronger than gray iron but poor castability Precision mold conveyor

Automatic core Setter

Disamatic molding operation

Microstructure check

International ductile iron specifications equivalent to

Molten metal pour

ASTM A536 Gr. 65-45-12 and or ASTM A395 Gr. 65-45-15 are; SAE J434: D4512 EN1563: EN-GJS-450-10 or EN-GJS-450-15 JIS G5502: FCD450-10 SABS 936/937: SG42 Physical strength of materials comparative ASTM Designation Ductile iron castings A536: Gr. 65-45-12 Ductile iron castings A395: Gr. 65-45-15 Forged carbon steel A105 Cast carbon steel A216: WCB Carbon steel pipe A53: Gr. B Malleable iron castings A47: Gr. 32510 Gray iron castings A126: Gr. B


Tensile Strength, min. psi (MPa) 65,000 (448) 65,000 (448) 70,000 (485) 70,000 (485) 60,000 (415) 51,000 (345) 31,000 (214)

Yield Strength, Elongation min. psi (MPa) in 2”, % 45,000 (310) 12 45,000 (310) 15 40,000 (250) 20 36,000 (205) 22 35,000 (240) (29.5) 32,000 (224) 10 Not specified Not specified


www.shurt.com

Catalog 2011

Bolts & Nuts Carbon steel bolts and nuts

Shurt products utilize oval neck track bolts conforming to ASTM A449 and ASTM A183 Gr. 2 and heavy duty nuts to ASTM A563 Gr. B, available with UNC threads or ISO metric threads. The UNC track bolts and nuts are supplied electro zinc plated in a silver chromate color and ISO metric bolts and nuts in a gold chromate color. Hot-dip galvanized bolts and nuts are also available upon request.

A stainless steel bolt fastened with a silicon bronze nut

ASTM A193, Grade B8M (Type 316) Stainless Steel Bolts

ASTM A449, Quenched and Tempered Steel Bolts*

Chemical Requirements Minimum Carbon, % 0.28 Manganese, % 0.60 Phosphorus, % Sulfur, % Physical Properties

Maximum 0.55 0.040 0.050

Tensile strength, psi (MPa)

120,000 (825)

-

Yield strength, psi (MPa)

92,000 (635)

-

Elongation, %

14

-

*Equivalent to property class 8.8 bolts per ISO 898.

ASTM A183, Grade 2 Carbon Steel Track Bolts

Chemical Requirements Minimum Carbon, % 0.30 Phosphorus, % Sulfur, % Physical Properties


110,000 (760) 80,000 (550) 12

Maximum 0.05 0.06 -------

ASTM A563, Grade B Carbon and Alloy Steel Heavy Hex Nuts

Chemical Requirements (bolts) Minimum Carbon, % Phosphorus, % Sulfur, % Physical Properties

Hardness, Rockwell

B69

Maximum 0.55 0.12 0.15 C32

Chemical Requirements Minimum Carbon, % Manganese, % Phosphorus, % Sulfur, % Silicon Chromium, % 16.00 Nickel, % 10.00 Molybdenum 2.00 Physical Properties


75,000 (515) 30,000 (205) 30

Maximum 0.08 2.00 0.045 0.030 1.00 18.00 14.00 3.00 -

Silicon Bronze Nuts ASTM B98 Alloy B Copper-Silicon Alloy (UNS No. C65100)

Chemical Requirements Minimum Copper, % 96.0 Lead, % Iron, % Zinc, % Magnesium, % Silicon, % 0.8 Physical Properties


55,000 (380) 20,000 (140) 11

Maximum 0.05 0.8 1.5 0.7 2.0

12

Recommended Bolt Torque

Always use factory supplied bolts and nuts for assembly of Shurt

Stainless steel bolts and nuts

Stainless steel track bolts and nuts, type 304 or type 316, are supplied with Shurt stainless steel couplings. Track bolts and

nuts are molybdenum disulfide (MoS2) coated to inhibit galling. As an option, silicon bronze nuts are also available to further reduce the chance of galling.

couplings. Shown below are the general recommended torque ranges for common sizes of carbon steel bolts. Never exceed the recommended torque range by more than 25% as excessive torque can lead to t failure, personal injury and or property damage. Always depressurize and drain the piping system before attempting disassembly, adjustment or removal of any piping component. Follow installation instructions for proper assembly of all Shurt

ASTM A193, Grade B8 (Type 304) Stainless Steel Bolts

Chemical Requirements Minimum Carbon, % Manganese, % Phosphorus, % Sulfur, % Silicon Chromium, % 18.00 Nickel, % 8.00 Physical Properties


75,000 (515) 30,000 (205) 30


Maximum 0.08 2.00 0.045 0.030 1.00 20.00 10.50 -------

components. For questions Shurt.

mm M8 M10 M12 M16 M20

Bolt Size

in 5/16” - 18 ⅜” - 16 ½” – 13 ⅝” - 11 ¾” - 10

Proper Torque Range N-m Lbs-Ft 9 - 18 7 – 14 20 - 30 15 – 22 40 - 68 30 – 50 81 - 122 60 – 90 129 - 237 96 - 175

For stainless steel bolts, reduce by 20%

www.shurt.com


Catalog 2011

Rubber Gasket Compounds The 20th century was the era of innovation in plastic and rubber materials. Among the new synthetic rubber compounds that most impacted our industry were EPDM (ethylene propylene diene monomer) and Nitrile rubbers.

EPDM is recognized as the most water resistant

NBR, Buna-N, and Nitrile

rubber available today. Good for cold & hot water,

represent the same copolymer of butadiene and

steam up to 250ºF (121ºC), waste water, water

acrylonitrile (ACN), which is inherently resistant to

with acid, deionized water and seawater. EPDM is

hydraulic fluids, lubricating oils, transmission fluids

not recommended for use with petroleum based oils and fuels, hydrocarbon solvents and aromatic

all

Green Stripe

hydrocarbons.

and other non-polar petroleum based products

Orange Stripe

and water less than 150º F (65º C). The higher the ACN content,

Shurt Grade "E" EPDM is compounded per ASTM D2000 designation 2CA615A25B24F17Z. Peroxide curing and post curing give a higher crosslink density, which provides a higher aging

the higher the resistance to oils and heat, but the lower elastic characteristics and compression set. NBR displays poor resistance to hot water and steam.

resistance than required in AWWA C606. Shurt grade “T” NBR rubber is compounded based on ASTM AWWA C606 2CA 615A25B24F17Z Basic Requirements Hardness, Durometer A, point 65±7 Tensile strength, psi, min. 1500 psi (10.34 MPa) Elongation, %, min. 300 % Heat Aging Properties After aged at 212°F (100°C) for 70 hours Change in Durometer hardness, max. +10 point Change in tensile strength, max. -25% Change in ultimate elongation, max. -25% Compression Set, Method B, max. 25%

Shurt Standard 60±5 1500 psi (10.34 MPa) 300 % After aged at 257°F (125°C) for 70 hours +5 points -10% -20% 20%

Use Shurt Grade "E-pw" for potable water and food processing services. The Grade "E-pw" is UL classified per ANSI/NSF 61 for cold +86°F (30°C) and hot +180°F (82°C) potable water services. EPDM seals are recommended for use in breweries as they have the least impact on the characteristics of beer or wort.

Double Green Stripe

Note: EPDM materials used in domestic water applications with high levels of chlorine and or chloramines should be subjected to resistance testing, as not all materials will be suitable. EPDM materials with higher saturated ethylene content and lower carbon black content are recommended for chloramine and chlorine resistance. Shurt for further information.

D2000 designation 5BG615A14B24Z and exceeds the requirements of AWWA C606. Grade “T” is a general purpose compound with a medium ACN level. For fuels, especially those with a low aniline point, such as or unleaded gasoline, ASTM referenced fuels B & C and naphtha, use Shurt grade “M2” Epichloro-Hydrin or grade “O” Flurocarbon. AWWA C606 Shurt 5BG615A14B24Z Standard Basic Requirements Hardness, Durometer A, point 60±7 60±5 Tensile strength, psi, min. 1500 psi (10.34 MPa) 1500 psi (10.34 MPa) Elongation, %, min. 300 % 300 % When heat aged at 212°F (100°C) for 70 hours Change in Durometer hardness, max. +10 point ±10 points Change in tensile strength, max. -25% -20% Change in ultimate elongation, max. -30% -30% Compression Set, Method B, max. 25% 25%

Use Shurt Grade "A" white Nitrile gaskets for oily and greasy food products and processing, as well as pharmaceutical and cosmetics manufacturing. The Grade "A" is compounded from FDA approved ingredients (CFR Title 21 Part 177.2600).

White Gasket

Use Shurt Grade "S" Nitrile gaskets for ts with AWWA ductile iron pipe. Good for mineral oils, vegetable oils, air with oil vapors and water less than 150°F (65°C).

Red Stripe

Laboratory high temperature oven testing



www.shurt.com

Catalog 2011

Silicone (VMQ)

Epichloro-Hydrin (ECO)

Shurt Grade "L"

Shurt Grade "M2" compound offers good to

Silicone compound features high temperature

excellent resistance to aliphatic hydrocarbon and

range stability and low temperature flexibility.

aromatic hydrocarbon fuels at low temperatures, LP

Recommended for dry heat and air without hydrocarbons up to 350º F (177º C). Silicone compounds are used in many food and medical

gases & fuels, mineral oils and many solvents. ECO Red Gasket

offers limited resistance to many organic chemicals.

White Stripe

applications as they do not impart odor or taste. Not recommended for hot water or steam services.

Halogenated Butyl (CIIR) Shurt Grade "M" CIIR is specially compounded

Chloroprene (CR, Neoprene)

for use with AWWA ductile iron pipe for water

a general purpose elastomer that demonstrates

chemicals. The compound is UL classified for

services, mild dilute acids, oil-free air and many

Shurt Grade "V" chloroprene rubber is

potable water use per ANSI/NSF 61.

good resistance to lubricating oils, animal & vegetable fats and greases. Chloroprene is not

Brown Stripe

Yellow Stripe

effective in aromatic and oxygenated solvent environments and is not recommended for hot water and steam services.

Fluorocarbon (FKM) FKM is a highly

fluorinated carbon backboned compound, which

is also known by the commercial name of Viton®. Shurt Grade "O" fluorocarbon compound offers excellent resistance to harsh chemical and ozone attack with a thermal stability to 300°F (149°C).

Blue Stripe

The Grade "O" gasket is recommended for use with oils, gasoline, hydraulic fluids, hydrocarbon solvents and extended fuels that fall outside the service parameters of grade T / NBR compounds. Not

Laboratory hot water & steam testing

recommended for steam services. (Viton® is a ed trademark of DuPont.)

Service temperatures

The following chart can

serve as a general guide for temperature and media compatibility for

Shurt gaskets. The range shown below is only a guide and s should always test the gasket materials for the specific operating and service application, as conditions can vary. Air Hot Water Steam (continuous)* Steam (intermittent)*

EPDM NBR VMQ CR Grade E Grade T Grade L Grade V -30 to +260°F -20 to +180°F -30 to +350°F -30 to +180°F -34 to +127°C -29 to +82°C -34 to +177°C -34 to +82°C 212°F 150°F 150°F 150°F 100°C 65°C 65°C 65°C 230°F 110°C NR NR NR 250°F 121°C

FKM Grade O -20 to +300°F -29 to +149°C 212°F 100°C

ECO Grade M2 -20 to + 160°F -29 to + 71°C 150°F 65°C

CIIR Grade M -20 to + 200°F -29 to + 93°C 180°F 82°C

NR NR NR

*Some codes do not allow the use of EPDM for steam services.


www.shurt.com


PLAIN-END PIPING SYSTEM

Catalog 2011

Pressure-Temperature Ratings

Service temperatures

Shurt has incorporated the ASME/ANSI nominal pressure-temperature rating method, to identify and describe working pressures of grooved mechanical components, so that engineers and designers can select Shurt components in the same manner and method that they do when selecting other fittings, flanges, valves, pumps and other piping components.

Service temperatures are limited by the flow media and gasket grade.

Refer to the chart of Pressure-Temperature Ratings for Class 125, 150, 250, 300 and 400 shown on the next page. Maximum working pressures shown in this catalog are rounded numbers rather than those specified in ASME/ANSI standards. All pressure ratings shown in this catalog are based on use of cut or roll-grooved standard weight (STD) carbon steel pipe within a temperature range of -20°F to +100°F (-29°C to +38°C).

For example Grade "E" EPDM and Grade "T" Nitrile gaskets can be used in the temperature ranges listed below. Temperature Limitations Rubber Compound EPDM (Grade E) Nitrile (Grade T)

Air -30°F to +260°F (-34°C to +127°C) -20°F to +180°F (-29°C to +82°C)

Water 212°F (100°C) 150°F (65°C)

Steam Continuous: 230°F (110°C) Not recommended

Temperature limitations are guidelines when compounds are used as a sealing gasket of grooved mechanical components. For high temperature services, Grooved mechanical components should be installed at accessible locations for replacement of gaskets if required.

Vacuum Service

Standard Shurt gaskets are designed to seal well under vacuum conditions up to 10 inHg (absolute)/254 mmHg (absolute) which may occur when a system is drained.

Maximum Working Pressure at +100°F (+38°C)

Nominal Rating Class 125 Class 150 Class 250 Class 300 Class 400

ASME/ANSI B16.1, B16.5, B16.34 175 psi 285 psi 400 psi 740 psi 990 psi

Shurt 2011 Catalog 175 psi (12 Bar) 300 psi (20 Bar) 400 psi (28 Bar) 750 psi (52 Bar) 1000 psi (70 Bar)

Pressures are shown in psi (pounds per square inches) and temperatures in Fahrenheit (°F) with converted pressures in Bar (MPa x 10) and temperatures in Celsius (°C).

Vacuum testing

The performance parameters of grooved mechanical components will vary depending on the pipe wall thickness, material, diameter and the type of grooves processed. For example the pressure rating of a Class 150 coupling used on schedule 7 pipe would be lower than that of the same coupling used on standard wall pipe.

Refer to the Performance Data Sheet, shown on page 39, for actual working pressures at ambient temperatures (or CWP - cold working pressures) for each pipe schedule or wall thickness of carbon steel and stainless steel pipes. Proof test pressures are 1.5 times the maximum working pressures (non-shock cold water). Burst test pressures are minimum 3 times the maximum working pressures for sizes up to 12” and minimum 2 times for sizes 14” and above.

CWP (Cold working pressure) Pressure ratings of grooved components that do not conform to the applicable ASME/ANSI pressure-temperature ratings are shown in CWP. Grooved components used for fire protection systems shall be listed by UL and or approved by FM and or other approval bodies such as VdS, LPCB, etc., as may be required by local authorities and or codes. Refer to the Approved Pressure Ratings by UL and FM which are shown at the end of this catalog. Pressure ratings of some valves that are designed to MSS standards are also shown in CWP.



Hydrostatic testing - 72" R-88 coupling

www.shurt.com

Catalog 2011

Pressure-Temperature Ratings Fittings, Flanges & Valves ANSI B16.4, B16.5, B16.34 & BS EN 1092-1

Psig

Bar 70

60

ASTM A216 Gr. WCB ASTM A351 Gr. CF8M ASTM A126 Class A ASME SA105

Class 400

1000

900

800

700

600 (PN40)

EPDM

500

Class 250

400

Line

30

eam

40

Class 300

Class 150

300

rate

20

d St

(PN25)

Satu

Pressure

50

(PN16)

200

Class 125

10 100

0

0

0 -50

EPDM NITRILE (NBR)

100 0

50

200

300

100

AIR WATER


200

500 250

600 300

700 °F

650 350

°C

Temperature

AIR WATER

150

400

STEAM

Shurt Gr. E (EPDM) and Gr. T (NBR, Nitrile) gaskets are compatible with air, water and steam within the referenced temperature ranges. As a general rule, all rubber materials lose elasticity as temperature increases. For elevated temperature services, GMC should be installed at accessible locations for replacement of gaskets if required.

www.shurt.com


Catalog 2011

Standards and Codes Shurt production facilities are certified to ISO 9001. Products are

various approval bodies and registration authorities. Shurt is also

designed to conform and meet or exceed all applicable domestic and

active in industry and environmental organizations.

international standards and are listed, approved and or certified by

American Standards ASME/ANSI

B1.1: Unified Inch Screw Threads (UNC) B1.20.1: Pipe Threads (NPT) B16.3: Malleable Iron Threaded Fittings B16.5: Steel Flanges & Flanged Fittings B16.9: Wrought Steel Butt-Welding Fittings B16.14: Plugs, Bushings & Locknuts B16.34: Valves – Flanged & Butt-welding Ends B16.39: Malleable Iron Threaded Unions B16.42: Ductile Iron Flanges & Flanged Fittings B31.1: Power Piping B31.3: Process Piping B31.9: Building Services Piping B36.10: Wrought Steel Pipe B36.19: Stainless Steel Pipe

ASTM

A53: Steel Pipe A106: Seamless Carbon Steel Pipe A135: Electric-Resistance-Welded Steel Pipe A795: Steel Pipe for Fire Protection Use B75: Seamless Copper Tube B88: Seamless Copper Water Tube B306: Copper Drainage Tube (DWV) A395: Ferritic Ductile Iron A536: Ductile Iron Castings A351: Austenitic Stainless Steel Castings A743: Iron-Chromium-Nickel Castings for General Application A744: Iron-Chromium-Nickel Castings for Severe Service A890: Duplex (Austenitic / Ferritic) Stainless Steel A985: Steel Investment Castings B584: Copper Alloy Castings A183: Carbon Steel Track Bolts and Nuts A193: Alloy & Stainless Steel Bolting Materials A194: Carbon & Alloy Steel Nuts A307: Carbon Steel Standard Fasteners A449: Quenched and Tempered Steel Bolts A105: Steel Forgings for Piping Components A234: Wrought Carbon Steel Fittings


A153: Hot-Dip Zinc Coatings A633: Electro-Zinc Coatings D1784: PVC and VC Compounds D1785: PVC Pipe (Sch. 40, 80 & 120) D2000: Classification System of Rubber Products D2513: PE Gas Pressure Pipe and Fittings D3350: PE Plastic Pipe & Fittings Materials F1476: Grooved Mechanical Couplings F1548: Fittings for Grooved Couplings

API

API 5L: Line Pipe API 594: Check Valves API 598: Valve Inspection and Testing

ANSI/AWWA

C606: Grooved and Shouldered ts C151/A21.51: Ductile-Iron Pipe C153/A21.53: Ductile-Iron Compact Fittings C901: PE Pressure Pipe and Tubing

MSS

SP-25: Standard Marking System for Valves & Fittings SP-67: Butterfly Valves SP-72 Ball Valves SP-110: Ball Valves (Grooved) SP-136 Ductile Iron Check Valves

NFPA

NFPA 13: Installation of Sprinkler Systems

SAE

SAE J403: Chemical Compositions of SAE Carbon Steels SAE J1199: Mechanical and Material Requirements for Metric Externally Threaded Steel Fasteners

ABS

IACS UR P2.11: Type Approval of Mechanical t

Canadian Standards

CSA B242: Grooved & Shouldered Couplings

Japanese Standards

MP006 Housing Type ts

Approval Bodies

UL 213: Rubber Gasketed Fittings for Fire Protection Service


ULC/ORD-C213: Rubber Gasketed Fittings for Fire Protection Service FM Class 1920: Pipe Couplings and Fittings for Aboveground Fire Protection Systems VdS 2100-06en: Pipe ts, Requirements and Test Methods LPCB LPS-1219: Requirements for Testing Pipe Couplings FESC: Japan Fire Equipment Safety Center CNBOP: Scientific and Research Centre for Fire Protection TSUS: Technický a Skúšobný Ústav Stavebný, n. o.

Registrations

Lloyd’s: Lloyd’s Quality Assurance NYC-MEA: New York City Department of Buildings, Materials and Equipment Acceptance NYPA: New York Power Authority CRN: Canadian Boiler Branch Registration DLEG: State of Michigan Board of Mechanical Rules CE PED: Pressure Equipment Directory 97/23/EC

Associations

NFPA: National Fire Protection Association NFSA: National Fire Sprinkler Association, Inc. CASA: Canadian Automatic Sprinkler Association IFSA: International Fire Sprinkler Association MCAA: Mechanical Contractors Association of America ASHRAE: American Society of Heating, Refrigerating and Air Conditioning Engineering

Environment

ANSI/NSF 61: Standard 61 for potable water service USGBC: US Green Building Council WEF: Water Environment Federation AMTA: American Membrane Technology Association USGBC: US Green Building Council WRAS: Water Regulatory Advisory Scheme

www.shurt.com

Section 1

Grooved Mechanical Couplings, Flange Adapters & Mechanical Tees

Grooved Mechanical Couplings................................................... 12 Rigid & Flexible Couplings. ........................................................... 13 M-7 Installation-Ready Rigid Coupling................................................ 14 Z05 Rigid Coupling.............................................................................. 15 Z07 Heavy Duty Rigid Coupling.......................................................... 16 XH-1000 Extra Heavy Rigid Coupling............................................... 17 7705 Flexible Coupling....................................................................... 18 7707 Heavy Duty Flexible Coupling.................................................... 19 7707N Flexible Coupling, 14” – 24”.................................................... 20 7707L Large Diameter Coupling........................................................ 21 7706 Reducing Coupling.................................................................... 22 G-28 Hinged Lever Coupling.............................................................. 23 C-7 Outlet Coupling............................................................................. 24 7706-T & 7771-T Transition Couplings........................................... 25 XH-70EP Extra Heavy Rigid Coupling w/EP Gasket......................... 26 Flange Adapters. ................................................................................ 27 7041 Flange Adapter, ANSI Class 125/150........................................ 28 7041 Flange Adapters, PN10/16 & BS 10 Table E............................. 29 7043 Flange Adapter, ANSI Class 300............................................... 30 49 Sandwich Plate............................................................................... 30 7180 & 7181 Universal Flange Adapters......................................... 31 7170 Solid Flange Adapters, ANSI Class 125/150............................. 32 Mechanical Tees................................................................................. 33 M21 & 7721 Mechanical Tee, Female Threaded Outlet................... 34 M22 & 7722 Mechanical Tee, Grooved-end Outlet.......................... 36 723 Saddle-Let (Small Mechanical Tee)............................................. 38 Performance Data Sheet................................................................. 39


Catalog 2011

www.shurt.com

Catalog 2011

Shurt Grooved Mechanical Couplings The Shurt grooved piping system is one of the most advanced, versatile, economical and reliable systems available today. After the pipe ends are grooved a gasket is mounted over the pipe ends. The coupling segments are then placed over the gasket and the bolts and nuts are fastened resulting in a secure and leak free t. A coupling can be installed 3 – 4 times faster than a comparable welded or brazed t and there is no need for a flame or welding torch on the job site. A grooved mechanical coupling can be installed by fastening a pair of bolts and nuts while using only a wrench or spanner, whereas a comparable flanged t requires the fastening of many bolts and nuts with a pair of wrenches. The grooved system allows for easy material take-offs and unlike a threaded system, there

Helpful Information to Ensure Proper Assembly

Some couplings and components require the housing bolt pads to make metal-to-metal for proper assembly, while others require a specific bolt torque while maintaining equal bolt pad gaps. The icons and information below will help to identify those items to ensure proper assembly. Read and follow all installation instructions for the component being installed. Metal-to-metal : Tighten bolts and nuts until bolt pads make metal-to-metal . After metal-to-metal is achieved, tighten nuts by another one quarter or one half turn to make sure the bolts and nuts are snug and secure. No torque wrench is required. Excessive torque may lead to bolt or t failure.

is no need to allow for added pipe length for thread engagement. With removal of just a few bolts one can easily access the system for cleaning, maintenance, changes and or system expansion.

No Gap

Metal-to-metal

After metal-to-metal, further tighten one quarter or half turn

Torque required! Bolts and nuts must always be tightened to the required torque by using a torque wrench. Normally there will be some gaps seen between the bolt pads after the bolts and nuts are fully tightened. Models that require torque tightening include 2” through 4” of model XH-1000, all sizes of models XH-70EP, SS-7X and 79 couplings. Always use a torque wrench

Installation-Ready Coupling

The development of the Shurt installation-ready coupling has continued the advancement of grooved systems, making it possible to further speed installation and performance. The factory supplied couplings are installation ready with no loose parts and no disassembly required.

#SS-7X 10” ~ 24”

Installation-Ready Coupling



www.shurt.com

#79 2” ~ 20”

Catalog 2011

Rigid & Flexible Couplings

Definition Grooved couplings are subjected

to internal pressures and exterior bending forces during service. ASTM F1476-07

Grooved mechanical couplings (GMC) are available in both rigid and flexible models. A rigid coupling is used in applications where a rigid t is desired, similar to that of a traditional flanged, welded, and or threaded connection. To be considered rigid, a coupling would allow less than one degree of deflection or angular movement. Flexible couplings are designed to

defines a rigid coupling as a t where there is essentially no available free angular

Bending Moment Test bending moments are calculated by the equation M = F (L),

and L is hanger spacing x 1/2 (feet). The table below shows test bending moments calculated using sch. 40 pipe with NFPA 13 hanger spacing.

θ shall be calculated as follows: θ° = 60’

Hanger Spacing

Water filled pipe

(minutes) – [2’ (minutes) x (nominal pipe size in inches)]. In other words, when θ is

F

less than 1 degree (60 minutes), the grooved mechanical coupling is verified as a rigid

to outside forces beyond normal static

L

conditions, such as seismic events or where

Bolt / Nut

coupling and when θ is more than 1 degree

L

(60 minutes), the GMC is regarded as a

M = F(L)

flexible coupling. The maximum angles θ for

Test Bending Moment (ASTM F1476)

Nom. Size (inches) 1½ 2 2½ 3 4 5 6 8 10 12 14 16

Moment N-m 549 780 1200 1645 2471 3551 4803 7663 11379 15558 18609 24299

Moment Lb-Ft 405 575 885 1213 1823 2619 3543 5652 8393 11475 13725 17922

Flexibility Proof Test Flexibility proof

Coupling Key

testing is conducted by applying a small

#7705 Flexible Coupling

Grooved couplings become less flexible as the pipe size increases. For sizes in excess of 18” (450 mm) couplings are very limited in

The rigid coupling shall the test when the angle has not changed more than angle θ.

layouts and or when systems are exposed

Coupling Housing Segment

Pressurized to rated pressure

where F is weight of water filled pipe (Lbs)

applications that call for curved or deflected

Gasket

M= 25% listed moment

limited angular and axial pipe movement.

movement. Flexible couplings are used in

Groove

internally pressurized to the rated pressure.

coupling as a t wherein there is available

and a minimum one degree of angular

vibration and or noise attenuation are a

moment to the test assembly which is

or axial pipe movement and a flexible

accommodate axial displacement, rotation

concern.

Rigidity Proof Test Rigidity proof testing

is conducted by applying 25% of the listed

bending moment, 10% of the listed moment, to the test assembly with no internal pressure. A 4” model 7705 or 7707 flexible coupling deflects 3 – 4 degrees depending on the type of groove processed.

their angular movement. Please refer to the following definition and test methods.

M = 10% listed moment

No internal pressure


rigid couplings are shown in the table below:

Rigid Coupling - Max. Deflection

Nom. Size (inches) 1½ 2 2½ 3 4 5 6 8 10 12 14 16

θ, max (minutes) 57 56 55 54 52 50 48 44 40 36 32 28

θ, max. (degrees) 0.95 0.93 0.92 0.90 0.87 0.83 0.80 0.73 0.67 0.60 0.53 0.47

Bending Moment Proof Test The

coupling shall resist a 100% listed bending moment while the assembly is internally pressurized to the rated pressure.

M = 100% listed moment

Pressurized to rated pressure

www.shurt.com


Catalog 2011

MODEL

M-7 INSTALLATION READY RIGID COUPLING Patented and Patents Pending

The Shurt Model M-7 is designed for

required. The advanced housing and

general service applications. The advanced

Fast-Fit gasket designs result in superior

design and features make this coupling

compression and sealing dynamics while

the right choice to speed installation and

reducing the possibility of gasket pinching.

performance. The M-7 is supplied installation

Hanging requirements correspond to NFPA

ready with no loose parts and no disassembly

13, ASME B31.1 and B31.9.

Pressure-Temperature Rating Nom. Rating

Working Pressure (STD, Roll-grooved)

Max. Service Temperature

750 psi @100°F 52 Bar @38°C

EPDM: 230°F / 110°C Nitrile: 180°F / 82°C

Class 300

B

*Working pressure is based on roll- or cut-grooved standard wall carbon steel pipe. *Proof test pressure: 1.5 times the working pressure, non-shock cold water. *Burst pressure is engineered minimum 3 times the working pressure.

Features • Installation ready • Enhanced t rigidity • Reduced chance of gasket pinching • Superior compression & sealing capability

C

Housing Segment

Compression Pad

A

Nominal Pipe Max. Working Size O.D. Pressure mm / in mm / in Bar / PSI 50 60.3 52 2 2.375 750 65 73.0 52 2½ 2.875 750 80 88.9 52 3 3.500 750 100 114.3 52 4 4.500 750 125 141.3 52 5 6.500 750 150 168.3 52 6 6.625 750

Max End Load kN / Lbs 14.8 3320 21.8 4870 32.3 7210 53.3 11920 81.5 18220 115.6 25840

Axial Dimension Displacement A B C mm / in mm / in mm / in mm / in 0 – 1.6 90 126 48.5 0 – 0.06 3.54 4.96 1.90 0 – 1.6 105 140 48.5 0 – 0.06 4.13 5.51 1.90 0 – 1.6 112 158 48.5 0 – 0.06 4.40 6.22 1.90 0 – 3.2 147 219 51.0 0 – 0.13 5.78 7.00 2.00 0 – 1.6 175 228 51.0 0 – 0.06 6.89 8.98 2.00 0 – 1.6 203 255 51.0 0 – 0.06 8.00 10.04 2.00

Bolt Size mm / in M10 x 55 ⅜ x 2⅛ M10 x 55 ⅜ x 2⅛ M10 x 70 ⅜ x 2¾ M10 x 70 ⅜ x 2¾ M12 x 75 ½ x 3 M12 x 75 ½ x 3

Weight Kgs / Lbs 0.9 2.1 1.1 2.5 1.6 3.6 2.3 5.0 3.0 6.6 3.7 8.1

Step 1

Step 2

Step 3

• Place the coupling over one pipe end. The center gasket leg serves as your indication to stop.

• Insert the second pipe end or component into the coupling, butting it up to the center leg of the gasket.

• Tighten bolts and nuts until the housing segments and compression pads make metal-to-metal *.

The Model M-7 is supplied factory assembled. Do not disassemble the coupling prior to installation. Gaskets and housing parts are not interchangeable with other style couplings.

* Read and familiarize yourself with the complete Shurt installation instruction prior to installing, disassembling or adjusting any component.



www.shurt.com

Catalog 2011

MODEL

Z05 RIGID COUPLING Angle-Pad Design

The Shurt Model Z05 is an angle-pad

With the removal of only one bolt you

design rigid coupling for moderate pressure

can make a fast and easy ‘swing-over’

piping services including fire mains, long

installation.

straight runs and valve connections. The angle-pad design allows the coupling housings to slide along the bolt pads when tightened. The result is an offset clamping action which provides a rigid t which resists so-called ‘snaking’ of a long straight run. and hanging requirements correspond to ANSI B31.1, B31.9 and NFPA 13.

Pressure-Temperature Rating Nom. Rating Class 150

The angle pad design allows for fast



300 psi @100°F 20 Bar @38°C


and easy swing-over installation with the removal of a single bolt.


B

C

A

Nominal Size mm / in 32 1¼ 40 1½ 50 2 65 2½ 76.1 mm 80 3 100 4 108.0 mm 133.0 mm 139.7 mm 125 5 159.0 mm 165.1 mm 150 6 200 8 200 JIS

Pipe O. D. mm / in 42.2 1.660 48.3 1.900 60.3 2.375 73.0 2.875 76.1 3.000 88.9 3.500 108.0 4.250 114.3 4.500 133.0 5.250 139.7 5.500 141.3 5.563 159.0 6.250 165.1 6.500 168.3 6.625 219.1 8.625 216.3 8.516

Max. Working Pressure Bar/PSI 20 300 20 300 20 300 20 300 20 300 20 300 20 300 20 300 20 300 20 300 20 300 20 300 20 300 20 300 20 300 20 300

Max. End Load kN / Lbs 2.80 649 3.66 850 5.71 1330 8.37 1950 9.09 2120 12.41 2885 18.31 4250 20.51 4770 27.77 6456 30.64 7125 31.35 7290 39.69 9199 42.80 9950 44.47 10340 75.37 17525 73.45 17079


Axial Displacement A mm / in mm / in 0 ~ 1.2 66 0 ~ 0.05 2.60 0 ~ 1.2 72 0 ~ 0.05 2.83 0 ~ 1.7 85 0 ~ 0.07 3.35 0 ~ 1.7 98 0 ~ 0.07 3.86 0 ~ 1.7 100 0 ~ 0.07 3.94 0 ~ 1.7 113 0 ~ 0.07 4.45 0 ~ 4.1 142 0 ~ 0.16 5.59 0 ~ 4.1 146 0 ~ 0.16 5.75 0 ~ 4.1 170 0 ~ 0.16 6.69 0 ~ 4.1 173 0 ~ 0.16 6.81 0 ~ 4.1 175 0 ~ 0.16 6.89 0 ~ 4.1 198 0 ~ 0.16 7.80 0 ~ 4.1 200 0 ~ 0.16 7.87 0 ~ 4.1 203 0 ~ 0.16 8.00 0 ~ 4.8 264 0 ~ 0.19 10.40 0 ~ 4.8 260 0 ~ 0.19 10.24

Dimensions B mm / in 102 4.00 109 4.29 117 4.61 132 5.20 136 5.35 148 5.83 176 6.93 182 7.17 224 8.82 227 8.94 229 9.02 250 9.84 246 9.69 249 9.80 330 12.99 340 13.39

Bolts Size C mm / in No. mm / in 46 M10 x 55 2 1.81 ⅜ x 2⅛ 46 M10 x 55 2 1.81 ⅜ x 2⅛ 47 M10 x 70 2 1.85 ⅜ x 2¾ 47 M10 x 70 2 1.85 ⅜ x 2¾ 47 M10 x 70 2 1.85 ⅜ x 2¾ 48 M10 x 70 2 1.88 ⅜ x 2¾ 54 M10 x 70 2 2.13 ⅜ x 2¾ 53 M10 x 70 2 2.09 ⅜ x 2¾ 54 M12 x 75 2 213 ½ x 3 53 M12 x 75 2 2.09 ½ x 3 53 M12 x 75 2 2.09 ½ x 3 54 M12 x 75 2 2.13 ½ x 3 54 M12 x 75 2 2.13 ½ x 3 54 M12 x 75 2 2.13 ½ x 3 64 M16 x 135 2 2.52 ⅝ x 55/16 64 M20 x 120 2 2.50 ¾ x 4¾

www.shurt.com

Weight Kgs / Lbs 0.64 1.41 0.66 1.46 0.79 1.74 0.93 2.05 0.98 2.16 1.20 2.60 1.64 3.62 1.87 4.12 2.33 5.14 2.57 5.67 2.58 5.69 2.75 6.06 3.05 6.72 3.07 6.77 6.07 13.38 7.00 15.43


Catalog 2011

MODEL

Z07 HEAVY DUTY RIGID COUPLING The Shurt Model Z07 is an angle-pad

action which provides a rigid t that resists

design rigid coupling for general piping

flexural and torsional loads. and

applications where rigidity is required

hanging requirements correspond to ANSI

including, mechanical rooms, valve

B31.1, B31.9 and NFPA 13.

connections fire mains and long straight runs.

Note: Model Z07N two-segment couplings are now available in sizes 14” - 24”. Model Z07 multi-segment couplings in sizes 14” - 24” are also available. Shurt for the Z07 multisegment data sheet. Please specify the model required when ordering.

The angle-pad design allows the coupling housings to slide along the bolt pads when tightened. The result is an offset clamping Pressure-Temperature Rating Working Pressure Size Nom. Rating (STD, Roll-grooved) 1¼” – 6” Class 300 32 - 150 8” – 12” Class 250 200 - 300 14” – 24” Class 150 350 - 600

750 psi @100°F 52 Bar @38°C 400 psi @100°F 28 Bar @38°C 300 psi @100°F 20 Bar @38°C


B


A


Nominal Size Pipe O. D. mm / in mm / in 32 42.2 1¼ 1.660 40 48.3 1½ 1.900 50 60.3 2 2.375 65 73.0 2½ 2.875 76.1 76.1 mm 3.000 80 88.9 3 3.500 100 114.3 4 4.500 139.7 139.7 mm 5.500 125 141.3 5 5.563 165.1 165.1 mm 6.500 150 168.3 6 6.625 200 219.1 8 8.625 250 273.0 10 10.750 300 323.9 12 12.750 216.3 200 JIS 8.516 267.4 250 JIS 10.528 318.5 300 JIS 12.539 350 (Z07N) 355.6 14 14.000 400 (Z07N) 406.4 16 16.000 450 (Z07N) 457.2 18 18.000 500 (Z07N) 508.0 20 20.000 600 (Z07N) 609.6 24 24.000

Max. Working Pressure Bar/PSI 52 750 52 750 52 750 52 750 52 750 52 750 52 750 52 750 52 750 52 750 52 750 28 400 28 400 28 400 28 400 28 400 28 400 20 300 20 300 20 300 20 300 20 300

Max. End Load kN / Lbs 7.27 1620 9.52 2130 14.84 3320 21.75 4875 23.64 5300 32.26 7210 53.33 11920 79.66 17810 81.50 18220 111.27 24870 115.62 25840 105.51 23360 163.81 36290 230.59 51040 102.83 22770 157.16 34800 222.97 49370 199.53 46160 259.30 60290 328.18 76300 405.16 94200 583.43 13650

1-1/4" ~ 24"

Axial Displacement A mm / in mm / in 0~1.2 68 0 ~ 0.05 2.68 0~1.2 74 0 ~ 0.05 2.91 0~1.7 86 0 ~ 0.07 3.39 0~1.7 100 0 ~ 0.07 3.94 0~1.7 102 0 ~ 0.07 4.00 0~1.7 115 0 ~ 0.07 4.53 0~4.1 147 0 ~ 0.16 5.78 0~4.1 175 0 ~ 0.16 6.88 0~4.1 177 0 ~ 0.16 6.97 0~4.1 200 0 ~ 0.16 7.87 0~4.1 203 0 ~ 0.16 8.00 0~4.8 268 0 ~ 0.19 10.55 0~3.2 327 0 ~ 0.13 12.86 0~3.2 377 0 ~ 0.13 14.86 0~3.2 264 0 ~ 0.13 10.39 0~3.2 321 0 ~ 0.13 12.63 0~3.2 372 0 ~ 0.13 14.65 0~3.2 408 0 ~ 0.13 16.06 0~3.2 467 0 ~ 0.13 18.39 0~3.2 525 0 ~ 0.13 20.68 0~3.2 582 0 ~ 0.13 22.93 0~3.2 687 0 ~ 0.13 27.05

Dimensions B mm / in 105 4.13 115 4.53 120 4.72 140 5.50 146 5.75 157 6.18 199 7.83 235 9.25 235 9.25 259 10.20 263 10.35 342 13.46 431 16.98 480 18.88 340 13.39 397 15.63 452 17.80 505 19.89 554 21.84 607 23.89 698 27.47 803 31.61

Bolts Size C mm / in No. mm / in 47 M10 x 55 2 1.85 ⅜ x 2⅛ 47 M10 x 55 2 1.85 ⅜ x 2⅛ 48 M10 x 70 2 1.88 ⅜ x 2¾ 48 M10 x 70 2 1.88 ⅜ x 2¾ 48 M10 x 70 2 1.88 ⅜ x 2¾ 48 M12 x 75 2 1.88 ½ x 3 54 M12 x 75 2 2.13 ½ x 3 54 M16 x 90 2 2.13 ⅝ x 3½ 54 M16 x 90 2 2.13 ⅝ x 3½ 54 M16 x 90 2 2.13 ⅝ x 3½ 54 M16 x 90 2 2.13 ⅝ x 3½ 64 M20 x 120 2 2.52 ¾ x 4¾ 65 --- 2 2.56 ⅞ x 6½ 65 --- 2 2.56 ⅞ x 6½ 64 M20 x 120 2 2.50 ¾ x 4¾ 65 --- 2 2.56 ⅞ x 6½ 65 --- 2 2.56 ⅞ x 6½ 75 --- 2 2.95 ⅞ x 5½ 75 --- 2 2.95 ⅞ x 5½ 79 --- 2 3.11 ⅞ x 5½ 76 --- 2 3.00 1 x 5½ 78 --- 2 3.06 1 x 5½

Shurt for the data sheet of multi-segment type Z07 14” through 24”



C

www.shurt.com

Weight Kgs / Lbs 0.7 1.6 0.9 2.0 1.1 2.4 1.1 2.4 1.2 2.6 1.4 3.1 2.0 4.4 3.0 6.6 3.0 6.6 3.4 7.5 3.2 7.1 7.1 15.7 10.4 27.4 11.8 26.0 7.4 16.3 10.5 23.1 12.4 27.4 16.0 35.3 17.9 30.5 22.3 40.1 26.2 57.8 32.1 70.8

Catalog 2011

MODEL

XH-1000 EXTRA HEAVY RIGID COUPLING The Shurt Model XH-1000 is an extra

cut grooved pipes or components. Sizes 2”

heavy rigid coupling designed for high

through 4” require a bolt torque of 60 - 70

pressure services up to 1000 psi (70 bar).

Ft-Lbs. with some bolt gaps. For sizes 6”

This coupling is painted green and is

and above, the bolt pads will make metal to

supplied with a standard C-shaped gasket

metal when properly installed with

and heavy duty bolts and nuts. The Model

no torque wrench required.

XH-1000 can be installed on standard roll or




2" - 6" Class 400

1000 psi @100°F 70 Bar @38°C

EPDM: 230°F / 110°C

8" - 12" Class 300

750 psi @100°F 52 Bar @38°C

C

B

A

Nitrile: 180°F / 82°C

*Working pressure is based on connection with cut or roll-grooved standard wall steel pipe. *Proof test pressure: 1.5 times the working pressure, non-shock cold water. *Burst pressure is engineered minimum 3 times the working pressure.

Nominal Size Pipe O. D. mm / in mm / in 50 60.3 2 2.375 65 73.0 2½ 2.875 80 88.9 3 3.500 100 114.3 4 4.500 150 168.3 6 6.625 200 219.1 8 8.625 250 273.0 10 10.750 300 323.9 12 12.750

Max. Working Pressure Bar/PSI 70 1000 70 1000 70 1000 70 1000 70 1000 52 750 52 750 52 750

Max. End Load kN / Lbs 20.0 4430 29.3 6490 43.4 9620 71.8 15900 155.6 34450 196.0 43800 304.2 68040 428.2 95710

Axial Displacement A mm / in mm / in 0 ~ 3.6 90 0 ~ 0.14 3.50 0 ~ 3.6 102 0 ~ 0.14 4.02 0 ~ 3.6 123 0 ~ 0.14 4.86 0 ~ 6.4 155 0 ~ 0.25 6.09 0 ~ 6.4 218 0 ~ 0.25 8.58 0 ~ 6.4 275 0 ~ 0.25 10.83 0 ~ 6.4 334 0 ~ 0.25 13.15 0 ~ 6.4 390 0 ~ 0.25 15.35

Dimensions B mm / in 150 5.90 168 6.62 188 7.38 222 8.74 295 11.61 364 14.33 424 16.70 480 18.90

Bolts C Size mm / in No. in 49 2 ⅝ X 2¾ 1.92 49 2 ⅝ X 2¾ 1.92 49 2 ⅝ X 2¾ 1.92 53 2 ¾ x 4¾ 2.10 57 2 ⅞ x 5½ 2.25 70 2 1 x 5½ 2.75 75 2 1 x 5½ 2.95 75 2 1 x 5½ 2.95

Weight Kgs / Lbs 1.6 3.4 1.7 3.8 2.2 4.8 3.8 8.4 8.0 17.6 10.9 24.0 14.2 31.2 16.7 36.7

Sizes 2” through 4” require a bolt torque of 60 – 70 Ft-Lbs (80 – 95 N-m). Normally you can see some gaps between the bolt pads.

Sizes 6” through 12” are designed to make a metal-to-metal when properly installed.


www.shurt.com


Catalog 2011

MODEL

7705 FLEXIBLE COUPLING The Shurt Model 7705 is a standard flexible coupling designed for use in a variety of moderate pressure general piping

vibration, noise and seismic tremors. The Model 7705 can even accommodate an

arced or curved piping layout. See Typical

applications. The Model 7705 coupling

Applications - Flexible Couplings on page

features flexibility that can accommodate

142.

misalignment, distortion, thermal stress, Pressure-Temperature Rating Nom. Rating



300 psi @100°F 20 Bar @38°C


Class 150


Nominal Actual Size O.D. mm / in mm / in 25 33.7 1 1.315 32 42.4 1¼ 1.660 40 48.3 1½ 1.900 50 60.3 2 2.375 65 73.0 2½ 2.875 76.1 76.1mm 3.000 80 88.9 3 3.500 101.6 101.6 mm 4.000 108.0 108.0 mm 4.250 100 114.3 4 4.500 133.0 133.0 mm 5.250 139.7 139.7 mm 5.500 125 141.3 5 5.563 159.0 159.0 mm 6.250 165.1 165.1 mm 6.500 150 168.3 6 6.625 200 219.1 8 8.625 200 (7705H) 219.1 8 8.625 250 273.0 10 10.750 300 323.9 12 12.750 216.3 200 JIS 8.516 267.4 250 JIS 10.528 318.5 300 JIS 12.539

B

A

Max. Angular Movement Dimensions Working Max. End Axial Per Coupling Pressure Load Displacement Degree Per Pipe A B C Bar / PSI kN / Lbs mm / in (°) mm / m in / ft mm / in mm / in mm / in 20 1.75 1.6 96 57 100 46 5° - 30’ 300 410 0.0625 1.16 2.24 3.94 1.81 20 2.80 1.6 76 66 103 46 4° - 20’ 300 650 0.0625 0.91 2.60 4.06 1.81 20 3.66 1.6 66 72 108 46 3° - 48’ 300 850 0.0625 0.80 2.83 4.25 1.81 20 5.71 1.6 53 84 129 48 3° - 01’ 300 1330 0.0625 0.63 3.31 5.08 1.89 20 8.37 1.6 44 99 142 48 2° - 30’ 300 1950 0.0625 0.52 3.90 5.59 1.89 20 9.09 1.6 42 102 147 48 2° - 24’ 300 2120 0.0625 0.50 4.02 5.79 1.89 20 12.41 1.6 36 116 169 48 2° - 04’ 300 2880 0.0625 0.43 4.57 6.65 1.89 20 16.21 1.6 31 129 200 52 1° - 48’ 300 3770 0.0625 0.38 5.07 7.90 2.05 20 18.31 3.2 59 138 192 52 3° - 24’ 300 4250 0.125 0.71 5.43 7.56 2.05 20 20.51 3.2 55 145 197 52 3° - 12’ 300 4770 0.125 0.67 5.71 7.76 2.05 20 27.77 3.2 48 165 231 52 2° - 46’ 300 6460 0.125 0.58 6.50 9.09 2.05 20 30.64 3.2 46 170 233 52 2° - 37’ 300 7120 0.125 0.55 6.69 9.17 2.05 20 31.35 3.2 45 172 234 52 2° - 36’ 300 7290 0.125 0.54 6.77 9.21 2.05 20 39.69 3.2 40 190 253 54 2° - 18’ 300 9200 0.125 0.48 7.48 9.96 2.13 20 42.80 3.2 39 196 261 54 2° - 14’ 300 9950 0.125 0.47 7.72 10.28 2.13 20 44.47 3.2 38 200 268 62 2° - 10’ 300 10340 0.125 0.45 7.87 10.55 2.44 20 75.37 3.2 28 260 350 64 1° - 40’ 300 17520 0.125 0.35 10.24 13.78 2.52 20 75.37 3.2 29 266 343 63 1° - 40’ 300 17520 0.125 0.35 10.47 13.50 2.48 20 117.01 3.2 23 343 425 64 1° - 20’ 300 27210 0.125 0.28 13.50 16.73 2.52 20 164.71 3.2 20 390 467 64 1° - 08’ 300 38280 0.125 0.24 15.35 18.39 2.52 20 73.45 3.2 30 254 348 62 1° - 42’ 300 17080 0.125 0.36 10.00 13.70 2.44 20 112.26 3.2 24 337 420 64 1° - 22’ 300 26100 0.125 0.29 13.27 16.54 2.52 20 159.26 3.2 20 389 478 64 1° - 10’ 300 37030 0.125 0.25 15.31 18.81 2.52

Deflection or angular movement is the maximum value that a coupling allows with no internal pressure. All DIN size 7705 couplings up to DN150 size and the DN200 7705H coupling are VdS approved in addition to cULus and FM approvals.



C

www.shurt.com

Bolt Size Weight mm / in Kgs / Lbs M10 x 45 0.6 ⅜ x 1¾ 1.3 M10 x 55 0.7 ⅜ x 2⅛ 1.5 M10 x 55 0.7 ⅜ x 2⅛ 1.6 M10 x 55 0.8 ⅜ x 2⅛ 1.8 M10 x 55 0.9 ⅜ x 2⅛ 2.0 M10 x 55 1.0 ⅜ x 2⅛ 2.1 M12 x 75 1.3 ½ x 3 2.8 M12 x 75 1.6 ½ x 3 3.6 M12 x 75 1.9 ½ x 3 4.1 M12 x 75 1.9 ½ x 3 4.1 M16 x 90 2.3 5/8 x 3½ 5.1 M16 x 90 2.7 ⅝ x 3½ 5.9 M16 x 90 2.7 ⅝ x 3½ 5.9 M16 x 90 3.0 ⅝ x 3½ 6.6 M16 x 90 3.1 ⅝ x 3½ 6.8 M16 x 90 3.2 ⅝ x 3½ 7.0 M16 x 90 5.8 ⅝ x 3½ 12.8 M20 x 120 7.1 ¾ x 4¾ 15.7 M20 x 120 8.2 ¾ x 4¾ 18.0 --- 10.8 ⅞ x 6½ 23.8 M20 x 120 5.8 ¾ x 4¾ 12.8 M20 x 120 8.0 ¾ x 4¾ 17.6 --- 10.3 ⅞ x 6½ 22.6

Catalog 2011

MODEL

7707 HEAVY DUTY FLEXIBLE COUPLING The Shurt Model 7707 heavy duty

that can accommodate misalignment,

flexible coupling is designed for use in a

distortion, thermal stress, vibration, noise

variety of general piping applications of

and seismic tremors. The Model 7707 can

moderate or high pressure services. Working

even accommodate an arced or curved

pressure is usually dictated by the wall thickness and rating of the pipe being used.

piping layout. See Typical Applications -

Flexible Couplings on page 142.

The Model 7707 couplings feature flexibility Pressure-Temperature Rating Working Pressure Size Nom. Rating (STD, Roll-grooved) 3/4” – 6” Class 300 20 - 150 8” – 12” Class 250 200 - 300

750 psi @100°F 52 Bar @38°C 400 psi @100°F 28 Bar @38°C

B

Max. Service Temperature EPDM: 230°F / 110°C Nitrile: 180°F / 82°C

C

A


3/4"~12" Nominal Size mm / in 20 ¾ 25 1 32 1¼ 40 1½ 50 2 65 2½ 76.1mm 80 3 100 4 139.7mm 125 5 165.1mm 150 6 200 8 250 10 300 12 200 JIS 250 JIS 300 JIS

Actual O.D. mm / in 26.7 1.050 33.4 1.315 42.2 1.660 48.3 1.900 60.3 2.375 73.0 2.875 76.1 3.000 88.9 3.500 114.3 4.500 139.7 5.500 141.3 5.563 165.1 6.500 168.3 6.625 219.1 8.625 273.0 10.750 323.9 12.750 216.3 8.516 267.4 10.528 318.5 12.539

Max. Working Pressure Bar / PSI 52 750 52 750 52 750 52 750 52 750 52 750 52 750 52 750 52 750 52 750 52 750 52 750 52 750 28 400 28 400 28 400 28 400 28 400 28 400

Max. End Axial Angular Movement Load Displacement Per Coupling Per Pipe A kN / Lbs mm / in (°) mm / m in / ft mm / in 2.91 1.6 116 54 6° – 46’ 650 0.0625 1.42 2.13 4.55 1.6 96 61 5° – 30’ 1020 0.0625 1.16 2.40 7.27 1.6 76 70 4° – 20’ 1620 0.0625 0.91 2.76 9.52 1.6 66 76 3° – 48’ 2130 0.0625 0.80 3.0 14.84 1.6 53 90 3° – 01’ 3320 0.0625 0.63 3.50 21.75 1.6 44 102 2° – 30’ 4870 0.0625 0.52 4.00 23.64 1.6 42 103 2° – 24’ 5300 0.0625 0.50 4.06 32.25 1.6 36 124 2° – 04’ 7210 0.0625 0.43 4.88 53.33 3.2 55 157 3° – 12’ 11920 0.125 0.67 6.18 79.66 3.2 46 186 2° – 37’ 17810 0.125 0.55 7.32 81.50 3.2 45 186 2° – 36’ 18220 0.125 0.54 7.32 111.27 3.2 39 211 2° – 14’ 24870 0.125 0.47 8.11 115.62 3.2 38 214 2° – 10’ 25840 0.125 0.45 8.24 105.51 3.2 29 276 1° – 40’ 233.60 0.125 0.35 10.86 163.81 3.2 23 343 1° – 20’ 36290 0.125 0.28 13.50 230.59 3.2 20 390 1° – 08’ 51045 0.125 0.25 15.35 102.83 3.2 30 276 1° – 42’ 22770 0.125 0.36 10.86 157.16 3.2 24 337 1° – 22’ 34800 0.125 0.29 13.27 222.97 3.2 20 389 1° – 10’ 49370 0.125 0.25 15.31

Dimensions Bolts B C Size Weight mm / in mm / in No. mm / in Kgs / Lbs 95 46 M10 x 45 0.6 2 3.74 1.81 ⅜ x 1¾ 1.3 99 46 M10 x 55 0.8 2 3.90 1.81 ⅜ x 2⅛ 1.7 108 46 M10 x 55 1.0 2 4.25 1.81 ⅜ x 2⅛ 2.1 124 45 M12 x 60 1.0 2 4.88 1.81 ½ x 2⅜ 2.1 133 46 M12 x 75 1.2 2 5.24 1.81 ½ x 3 2.6 150 46 M12 x 75 1.3 2 5.90 1.81 ½ x 3 2.9 150 46 M12 x 75 1.3 2 5.90 1.81 ½ x 3 2.9 171 48 M12 x 75 1.5 2 6.73 1.89 ½ x 3 3.3 213 54 M16 x 90 2.1 2 8.38 2.13 ⅝ x 3½ 4.6 241 54 M16 x 90 3.1 2 9.50 2.13 ⅝ x 3½ 6.8 241 54 M16 x 90 3.3 2 9.50 2.13 ⅝ x 3½ 7.2 286 54 M20 x 120 3.6 2 11.26 2.13 ¾ x 4¾ 7.9 289 54 M20 x 120 3.7 2 11.38 2.13 ¾ x 4¾ 8.1 356 62 --- 6.6 2 14.00 2.44 ⅞ x 5½ 14.5 425 64 --- 10.6 2 16.73 2.52 ⅞ x 6½ 23.3 467 64 --- 12.0 2 18.39 2.52 ⅞ x 6½ 26.4 356 62 M20 x 120 6.6 2 14.00 2.44 ¾ x 4¾ 14.5 420 64 --- 10.2 2 16.54 2.52 ⅞ x 6½ 22.4 478 64 --- 11.6 2 18.81 2.52 ⅞ x 6½ 25.5

Deflection or angular movement is the maximum value that a coupling allows with no internal pressure.


www.shurt.com


Catalog 2011

MODEL

7707N FLEXIBLE COUPLING The Shurt Model 7707N is a twosegment, flexible coupling for use with standard pipe, roll or cut grooved to AWWA C606 specifications. For 26", see page 21 for groove dimensions.




300 psi @100°F 20 Bar @38°C


Class 150


Size: 26" 14" ~ 24" B

C

A

Nominal Size mm / in 350 14 400 16 450 18 500 20 550 22 600 24 650 26

Actual Max. Working Pressure O.D. XS (0.500”)* STD (0.375”) LW (0.312”) mm / in Bar / PSI Bar / PSI Bar / PSI 355.6 20 20 17 14.000 300 300 250 406.4 20 20 17 16.000 300 300 250 457.2 20 20 17 18.000 300 300 250 508.0 20 20 17 20.000 300 300 250 558.8 20 20 17 22.000 300 300 250 609.6 20 20 17 24.000 300 300 250 660.4 20 20 17 26.0 300 300 250

Axial Angular Movement Dimensions Bolts Displacement Degree Per Per Pipe A B C Size Weight mm / in Coupling (°) mm / m in / ft mm / in mm / in mm / in No. in Kgs / Lbs 6.4 9.0 412 479 75 15.7 1° – 02’ 2 ⅞ x 6½ 0.250 0.11 16.23 18.85 2.95 34.5 6.4 8.0 463 547 75 18.4 0° – 54’ 2 1 x 6½ 0.250 0.10 18.23 21.53 2.95 40.5 6.4 7.0 520 605 79 22.3 0° – 48’ 2 1 x 6½ 0.250 0.08 20.45 23.81 3.11 47.1 6.4 6.0 571 656 79 24.5 0° – 44’ 2 1 x 6½ 0.250 0.08 22.48 25.82 3.11 54.0 6.4 6.0 621.4 724.6 79 28.6 0° – 39’ 2 ⅛ x 6½ 0.250 0.07 24.46 28.52 3.11 63.0 6.4 5.0 674 780 79 29.5 0° – 36’ 2 ⅛ x 6½ 0.250 0.06 26.55 30.70 3.11 65.1 6.4 5.0 754 842 125.6 68.3 0° – 34’ 4 ⅞ x 9⅝ 0.250 0.06 29.68 33.15 4.94 150.5

Deflection or angular movement is the maximum value that a coupling allows under no internal pressure. * Pressure ratings are based on cut-grooved XS carbon steel pipe.

30" 7707L couplings on a chill water system



www.shurt.com

Catalog 2011

MODEL

7707L LARGE DIAMETER

COUPLING

The Shurt Model 7707L large diameter couplings in sizes 28” - 42” (700mm - 1050 mm) are designed for ing large diameter IPS pipe that can be roll grooved. All couplings feature a six to eight segment design, incorporating two bolts at each segment t to ensure a positive connection and seal.

B




175 psi @100°F 12 Bar @38°C


A

A


40"~ 42"

28"~ 36"

Nominal Size mm / in 700 28 750 30 800 32 900 36 1000 40 1050 42

Pipe Max. Working Pressure O. D. XS (.500”)* STD (.375”) LW (.312”) mm / in Bar / PSI Bar / PSI Bar / PSI 711.2 17 12 9 28.0 250 175 125 762.0 17 12 9 30.0 250 175 125 812.8 17 12 9 32.0 250 175 125 914.4 17 12 9 36.0 250 175 125 1016.0 17 12 9 40.0 250 175 125 1066.8 17 12 9 42.0 250 175 125

Axial Displacement A mm / in mm / in 6.4 813 0.250 32.0 6.4 864 0.250 34.0 6.4 914 0.250 36.0 6.4 1016 0.250 40.0 6.4 1105 0.250 43.5 6.4 1156 0.250 45.5

C

B

C

Dimensions Bolts B C No Size mm / in mm / in in 920 127 12 ⅞x4 36.3 5.0 972 127 12 ⅞x4 38.3 5.0 1022 127 12 ⅞x4 40.3 5.0 1124 127 12 ⅞x4 44.3 5.0 1245 146 16 1 x 3½ 49.0 5.8 1295 146 16 1 x 3½ 51.5 5.8

Weight Kgs / Lbs 82 180 95 209 94 207 96 212 123 271 140 308

* Pressure ratings are based on cut-grooved XS carbon steel pipe.

Standard Roll Groove for Large Diameter IPS Pipe t

A

O.D.

B C

1. Square cut: Max. allowable tolerances from square cut are 1.6mm (0.060”). 2. The gasket seating surface ‘A’ shall be free from deep scores, marks, or ridges that would prevent a positive seal. 3. The ‘C’ dimensions are average values. The groove must be of uniform depth around the entire circumference. Use a Shurt groove or rule to check the groove diameter. 4. The ‘t’ is the minimum allowable wall thickness that may be roll-grooved. 5. The ‘d’ is for reference use only. The groove depth shall be determined by the groove diameter ‘C’. 6. Flare Diameter: The pipe end that may flare when the groove is rolled shall be within this limit when measured at the extreme end of the pipe.

d Pipe Outside Diameter Nominal Size Basic Tolerance mm / in mm / in mm / in mm / in 650 660.4 +2.36 -0.79 26 OD 26.0 -0.093 -0.031 700 711.2 +2.36 -0.79 28 OD 28.0 -0.093 -0.031 750 762.0 +2.36 -0.79 30 OD 30.0 -0.093 -0.031 800 812.8 +2.36 -0.79 32 OD 32.0 -0.093 -0.031 900 914.4 +2.36 -0.79 36 OD 36.0 -0.093 -0.031 1000 1016.0 +2.36 -0.79 40 OD 40.0 -0.093 -0.031 1050 1066.8 +2.36 -0.79 42 OD 42.0 -0.093 -0.031


A +0.8, -1.6 +0.03, -0.06 mm / in 44.5 1.75 44.5 1.75 44.5 1.75 44.5 1.75 44.5 1.75 50.8 2.00 50.8 2.00

B ±0.8 ±0.03 mm / in 15.9 0.625 15.9 0.625 15.9 0.625 15.9 0.625 15.9 0.625 15.9 0.625 15.9 0.625

C +0, -1.6 +0, -0.063 mm / in 647.7 25.5 698.5 27.5 749.3 29.5 800.1 31.5 901.7 35.5 1003.3 39.5 1054.1 41.5

d Groove Depth (ref) mm / in 6.4 0.25 6.4 0.25 6.4 0.25 6.4 0.25 6.4 0.25 6.4 0.25 6.4 0.25

www.shurt.com

t Min. Allow Wall thick mm / in 6.4 0.25 6.4 0.25 6.4 0.25 6.4 0.25 6.4 0.25 6.4 0.25 6.4 0.25

Max Allowed Flare Dia. mm / in 665.5 26.2 716.3 28.2 767.1 30.2 817.9 32.2 919.5 36.2 1026.2 40.4 1071.9 42.2


Catalog 2011

MODEL

7706 REDUCING COUPLING The Shurt Model 7706 reducing coupling allows for direct reduction on a piping run and eliminates the need for a concentric reducer and additional couplings. The specially designed rubber gasket helps prevent small pipe from telescoping into

The Model 7706 coupling should not be used with an end cap, as the end cap could be sucked into the pipe by the vacuum created when a system is being drained.

larger pipe during vertical assembly.




300 psi @100°F 20 Bar @38°C


Class 150

B


Nominal Size mm / in 40 x 32 1½ x 1¼ 50 x 40 2 x 1½ 65 x 50 2½ x 2 76.1mm x 50 80 x 50 3 x 2 80 x 65 3 x 2½ 80 x 76.1mm 100 x 50 4 x 2 100 x 65 4 x 2½ 100 x 76.1mm 100 x 80 4 x 3 139.7mm x 100 125 x 100 5 x 4 165.1mm x 80 150 x 80 6 x 3 165.1mm x 100 150 x 100 6 x 4 200 x 150 8 x 6 200 x 165.1mm

Pipe O. D. mm / in 48.3 x 42.2 1.900 x 1.660 60.3 x 48.3 2.375 x 1.900 73.0 x 60.3 2.875 x 2.375 76.1 x 60.3 3.000 x 2.375 88.9 x 60.3 3.500 x 2.375 88.9 x 73.0 3.500 x 2.875 88.9 x 76.1 3.500 x 3.000 114.3 x 60.3 4.500 x 2.375 114.3 x 73.0 4.500 x 2.875 114.3 x 76.1 4.500 x 3.000 114.3 x 88.9 4.500 x 3.500 139.7 x 114.3 5.500 x 4.500 141.3 x 114.3 5.563 x 4.500 165.1 x 88.9 6.500 x 3.500 168.3 x 88.9 6.625 x 3.500 165.1 x 114.3 6.500 x 4.500 168.3 x114.3 6.625 x 4.500 219.1 x 168.3 8.625 x 6.625 219.1 x 165.1 8.625 x 6.500

Max. Working Pressure Bar/PSI 20 300 20 300 20 300 20 300 20 300 20 300 20 300 20 300 20 300 20 300 20 300 20 300 20 300 20 300 20 300 20 300 20 300 20 300 20 300

C

A

Max. End Load kN / Lbs 2.89 650 3.79 850 5.90 1330 5.90 1330 5.90 1330 8.66 1950 9.41 2115 5.90 1330 8.66 1950 9.41 2115 12.84 2890 21.23 4770 21.23 4770 12.84 2890 12.84 2890 18.95 4260 18.95 4260 46.03 10350 44.29 9960

Axial Angular Movement Dimensions Displacement Per Coupling Per Pipe A B C mm / in Degree (°) mm / m in / ft mm / in mm / in mm / in 0 ~ 3.2 33.0 72 108 46 3° - 48’ 0 ~ 0.13 0.40 2.83 4.25 1.81 0 ~ 3.2 26.0 85 122 48 3° - 02’ 0 ~ 0.13 0.31 3.35 4.80 1.89 0 ~ 3.2 22.0 96 144 48 2° - 30’ 0 ~ 0.13 0.26 3.78 5.67 1.89 0 ~ 3.2 21.0 102 138 48 2° - 24’ 0~0.13 0.25 4.02 5.43 1.89 0 ~ 3.2 18.0 116 168 48 2° – 04’’ 0~0.13 0.22 4.57 6.61 1.89 0 ~ 3.2 18.0 116 168 48 2° - 04’ 0 ~ 0.13 0.22 4.57 6.61 1.89 0 ~ 3.2 18.0 116 168 48 2° - 04’ 0 ~ 0.13 0.22 4.57 6.61 1.89 0 ~ 4.8 21.0 146 198 52 2° - 24’ 0 ~ 0.19 0.25 5.75 7.80 2.05 0 ~ 4.8 21.0 146 198 52 2° - 24’ 0 ~ 0.19 0.25 5.75 7.80 2.05 0 ~ 4.8 21.0 146 198 52 2° - 24’ 0 ~ 0.19 0.25 5.75 7.80 2.05 0 ~ 4.8 21.0 146 198 52 2° - 24’ 0 ~ 0.19 0.25 5.75 7.80 2.05 0 ~ 6.4 23.0 160 242 52 2° - 36’ 0 ~ 0.25 0.27 6.30 9.84 2.05 0 ~ 6.4 23.0 160 242 52 2° - 36’ 0 ~ 0.25 0.27 6.30 9.84 2.05 0 ~ 6.4 20.0 202 269 52 2° - 14’ 0 ~ 0.25 0.23 7.95 10.59 2.05 0 ~ 6.4 19.0 208 275 52 2° - 12’ 0 ~ 0.25 0.23 8.19 10.83 2.05 0 ~ 6.4 20.0 202 269 52 2° - 14’ 0 ~ 0.25 0.23 7.95 10.59 2.05 0 ~ 6.4 19.0 208 275 52 2° - 12’ 0 ~ 0.25 0.23 8.19 10.83 2.05 0 ~ 6.4 15.0 260 334 57 1° - 40’ 0 ~ 0.25 0.18 10.24 13.15 2.24 0 ~ 6.4 15.0 260 334 57 1° - 40’ 0 ~ 0.25 0.18 10.24 13.15 2.24

Deflection or angular movement is the maximum value that a coupling allows with no internal pressure.



www.shurt.com

Bolts Size mm / in M10 x 55 ⅜ x 2⅛ M10 x 55 ⅜ x 2⅛ M10 x 55 ⅜ x 2⅛ M10 x 55 ⅜ x 2⅛ M12 x 75 ½ x 3 M12 x 75 ½ x 3 M12 x 75 ½ x 3 M12 x 75 ½ x 3 M12 x 75 ½ x 3 M12 x 75 ½ x 3 M12 x 75 ½ x 3 M16 x 90 ⅝ x 3½ M16 x 90 ⅝ x 3½ M16 x 90 ⅝ x 3½ M16 x 90 ⅝ x 3½ M16 x 90 ⅝ x 3½ M16 x 90 ⅝ x 3½ M20 x 120 ¾ x 4¾ M20 x 120 ¾ x 4¾

Weight Kgs / Lbs 0.8 1.8 0.9 2.0 1.2 2.6 1.2 2.6 1.5 3.3 1.7 3.7 1.7 3.7 2.4 5.3 2.6 5.7 2.6 5.7 2.4 5.3 3.8 8.4 3.6 7.9 4.6 10.1 4.6 10.1 4.5 9.9 4.5 9.9 6.5 14.3 6.5 14.3

Catalog 2011

MODEL

g-28 hinged lever coupling The Model G-28 Hinged Lever Coupling is designed for quick connect and disconnect services. The housing segments are hinged with a locking lever handle for easy assembly. The use of the split pin can secure and prevent the accidental opening of the coupling. Pressure-Temperature Rating Nom. Rating



300 psi @100°F 20 Bar @38°C


Class 150

B

Split pin


Nominal Size mm / in 40 1½ 50 2 65 2½ 76.1 mm 80 3 100 4 139.7 mm 125 5 165.1 mm 150 6 200 8 250 10

Pipe O. D. mm / in 48.3 1.900 60.3 2.375 73.0 2.875 76.1 3.000 88.9 3.500 114.3 4.500 139.7 5.500 141.3 5.563 165.1 6.500 168.3 6.625 219.1 8.625 273.0 10.750

Max. Working Pressure Bar / PSI 20 300 20 300 20 300 20 300 20 300 20 300 20 300 20 300 20 300 20 300 20 300 20 300

C

A

Axial Displacement A mm / in mm / in 0 – 1.6 75 0 – 0.06 2.95 0 – 1.6 86 0 – 0.06 3.39 0 – 1.6 92 0 – 0.06 3.62 0 – 1.6 92 0 – 0.06 3.62 0 – 1.6 119 0 – 0.06 4.69 0 – 3.2 165 0 – 0.13 6.50 0 – 3.2 189 0 – 0.13 7.44 0 – 3.2 189 0 – 0.13 7.44 0 – 3.2 213 0 – 0.13 8.39 0 – 3.2 216 0 – 0.13 8.50 0 – 3.2 278 0 – 0.13 10.95 0 – 3.2 343 0 – 0.13 13.50

Dimensions Deflection B C Degree Weight mm / in mm / in (°) Kgs / Lbs 118 47 1.0 3° - 48' 4.65 1.85 2.2 121 48 1.1 3° - 01' 4.76 1.89 2.4 150 48 1.4 2° - 30' 5.91 1.89 3.1 150 48 1.4 2° - 24' 5.91 1.89 3.1 163 48 1.8 2° - 14' 6.42 1.89 4.0 205 52 2.7 3° - 12' 8.07 2.05 5.9 253 52 4.9 2° - 37' 9.96 2.05 10.8 253 52 4.9 2° - 36' 9.96 2.05 10.8 278 52 6.0 2° - 14' 10.94 2.05 13.2 281 52 6.0 2° - 10' 11.06 2.05 13.2 356 62 9.7 1° - 40' 14.02 2.44 21.4 452 64 16.4 1° - 20' 17.80 2.52 36.1

Deflection or angular movement is the maximum value that a coupling allows under no internal pressure.

Expansion Pipe

Lever handles are factory assembled tight for safety. The use of an expansion pipe will aid the easy opening and closing. Expansion pipes are available upon request.


www.shurt.com


Catalog 2011

MODEL

C-7 OUTLET COUPLING The Model C-7 Outlet Coupling combines the

recommended for fire sprinkler and other

features of a coupling and a reducing outlet.

pipelines of moderate pressure. The C-7

The C-7 facilitates an easy reducing branch

Outlet Coupling can be used for dry pipe

outlet without the need of a mechanical

systems or vacuum services up to 10 inHg

tee or reducing tee and couplings. The C-7

or 254 mmHg, which may occur when the

is available with grooved, male threaded

system is drained.

or female threaded outlets. This fitting is

A

B Grooved Outlet

C




300 psi @100°F 20 Bar @38°C


Class 150


Run pipe mm / in 40 1½ 50 2 65 2½ 80 3 100 4 150 6

Nominal Size Outlet FPT Gr / MPT mm / in mm / in 15 --- ½ --- 20 --- ¾ --- 25 --- 1 --- 15 --- ½ --- 20 --- ¾ --- 25 33.4 1 1 15 --- ½ --- 20 --- ¾ --- 25 --- 1 --- 32 42.2 1¼ 1¼ 40 48.3 1½ 1½ 20 --- ¾ --- 25 33.4 1 1 32 ---- 1¼ --- 48.3 48.3 1½ 1½ 20 --- ¾ --- 25 33.4 1 1 40 48.3 1½ 1½ 50 60.3 2 2 20 --- ¾ --- 25 --- 1 --- 40 48.3 1½ 1½ 50 60.3 2 2

T

Threaded Outlet

Max. Max. Dimensions Working Axial End Bolt Pressure Displacement Load T* A B C Size Weight Bar / PSI mm / in kN / Lbs mm / in mm / in mm / in mm / in mm / in Kgs / Lbs 20 20~22 52 --- 114 70 1.2 300 0.81~0.88 2.06 --- 4.50 2.75 2.6 20 20~22 3.7 52 --- 114 70 M10 x 55 1.2 300 0.81~0.88 850 2.06 --- 4.50 2.75 ⅜ x 2⅛ 2.6 20 20~22 49 --- 114 70 1.3 300 0.81~0.88 1.94 --- 4.50 2.75 2.9 20 20~22 59 --- 127 70 1.4 300 0.81~0.88 2.32 --- 5.00 2.75 3.1 20 20~22 5.7 59 --- 127 70 M10 X 55 1.4 300 0.81~0.88 1330 2.32 --- 5.00 2.75 ⅜ x 2⅛ 3.1 20 20~22 56 89 127 70 1.5 300 0.81~0.88 2.20 3.50 5.00 2.75 3.3 20 32~38 56 --- 161 83 2.2 300 1.25~1.50 2.20 --- 6.33 3.25 4.8 20 32~38 65 --- 161 83 2.1 300 1.25~1.50 2.56 --- 6.33 3.25 4.6 20 32~38 8.4 62 --- 161 83 M12 X 60 2.0 300 1.25~1.50 2120 2.44 --- 6.33 3.25 ½ x 2⅜ 4.4 20 32~38 64 94 161 83 2.3 300 1.25~1.50 2.52 3.70 6.33 3.25 5.1 20 32~38 --- 94 161 83 2.4 300 1.25~1.50 --- 3.70 6.33 3.25 5.9 20 32~38 72 --- 175 83 2.7 300 1.25~1.50 2.83 --- 6.87 3.25 5.9 20 32~38 70 102 175 83 2.8 300 1.25~1.50 12.4 2.75 4.00 6.87 3.25 M12 X 75 6.2 20 32~38 2890 70.0 102.0 175.0 83.0 ½ x 3 2.8 300 1.25~1.50 2.75 4.00 6.87 3.25 6.2 20 32~38 70.0 102 175 83 2.9 300 1.25~1.50 2.75 4.00 6.87 3.25 6.4 20 41~46 94 --- 211 93 4.2 300 1.63~1.81 3.70 --- 8.31 3.66 9.2 20 41~46 20.5 91 --- 211 93 4.3 300 1.63~1.81 4770 3.58 --- 8.31 3.66 M16 X 90 9.5 20 41~46 84 124 211 93 ⅝ x 3½ 4.3 300 1.63~1.81 3.31 4.88 8.31 3.66 9.5 20 41~46 89.0 124 211 93 4.5 300 1.63~1.81 3.50 4.88 8.31 3.66 9.9 20 41~46 121 --- 276 94 6.0 300 1.63~1.81 4.76 --- 10.86 3.70 13.2 20 41~46 121 --- 276 94 6.0 300 1.63~1.81 44.5 4.76 --- 10.86 3.70 M16 X 90 13.2 20 41~46 9950 121 154 276 94 ⅝ x 3½ 6.2 300 1.63~1.81 4.76 6.06 10.86 3.70 13.6 20 41~46 111.0 154 276 94 6.5 300 1.63~1.81 4.4 6.06 10.86 3.70 14.3

FPT : Female threaded outlet Gr: Grooved outlet MPT: Male threaded outlet *T : Center of run pipe to end of outlet pipe (dimensions approximate). Female threaded outlet only.


C


www.shurt.com

Catalog 2011

MODEL

7706-T TRANSITION COUPLING Model 7706-T Transition Couplings allows for a direct transition from IPS pipe sizes to ISO pipe sizes. Pressure-Temperature Rating Nom. Rating



300 psi @100°F 20 Bar @38°C


Class 150

B


Nominal Size mm / in 2½ x 76.1mm 6 x 165.1mm

Pipe O. D. mm / in 73.0 x 76.1 2.875 x 3.000 168.3 x 165.1 6.625 x 6.500

Max. Working Pressure Bar/PSI 20 300 20 300

C

ISO PIPE

A

Max. End Load kN / Lbs 5.90 1330 44.29 9960

Axial Angular Movement Dimensions Displacement Per Coupling Per Pipe A B C mm / in Degree (°) mm / m in / ft mm / in mm / in mm / in 0 ~ 3.2 21.0 102 138 48 2° - 24’ 0 ~ 0.13 0.25 4.02 5.43 1.89 0 ~ 6.4 19.0 200 270 53 1° - 06’ 0 ~ 0.25 0.23 7.87 10.63 2.09

IPS PIPE

Bolts Size mm / in M10 x 55 ⅜ x 2⅛ M16 x 90 ⅝ x 3½

Weight Kgs / Lbs 1.2 2.6 3.5 7.7

*Deflection or angular movement is the maximum value that a coupling allows with no internal pressure.

MODEL

7771-T Transition coupling The Shurt Model 7771-T Transition Coupling allows for a direct transition from IPS pipe sizes to JIS pipe sizes. Available in nominal pipe sizes from 8” through 12” this coupling can accommodate a combination of pipes, valves and or fittings with a single coupling. Bolt pads are designed to make metal to metal to provide for a secure and rigid t. The stepped exterior design of the housings

Stepped Design

help to ensure the correct positioning of IPS and JIS sides.

B

C




300 psi @100°F 20 Bar @38°C


A

IPS PIPE

JIS PIPE


Nominal Size mm / in 200 8 250 10 300 12

Actual Pipe O.D. IPS JIS mm / in mm / in 219.1 216.3 8.625 8.515 273.0 267.4 10.750 10.528 323.9 318.5 12.750 12.539

Max. Working Pressure Bar / PSI 20 300 20 300 20 300


Max. End Load kN / Lbs 75.37 17520 117.01 27190 164.71 38280

Total Axial Displacement A mm / in mm / in 3.2 259 0.13 10.20 3.2 316 0.13 12.46 3.2 367 0.13 14.45

Dimensions Bolts B C Size mm / in mm / in mm 335 63 M16 x 135 13.19 2.50 386 63 M20 x 120 15.20 2.50 448 63 M22 x 165 17.64 2.50

www.shurt.com

Weight Kgs / Lbs 7.0 15.4 9.0 19.8 11.0 24.2


Catalog 2011

MODEL

XH-70EP EXTRA HEAVY RIGID COUPLING

With End Protection (EP) Gasket

The Model XH-70EP is designed for use

corrosion. This coupling is rated up to 2500

with plastic coated or cement lined pipe.

psi (175 bar) when used in conjunction with

The EP (end protection) gasket serves to

machined EP cut grooves and the applicable

form a continuous lined surface at the t

pipe.

CAUTION: Always fasten the bolts to the required torque.

and also helps protect the pipe ends from C

B

A EP Gasket

Nominal Size Pipe O. D. mm / in mm / in 50 60.3 2 2.375 65 73.0 2½ 2.875 80 88.9 3 3.500 100 114.3 4 4.500 150 168.3 6 6.625 200 219.1 8 8.625 250 273.0 10 10.750 300 323.9 12 12.750

Max. Working Pressure Bar / PSI 175 2500 175 2500 175 2500 175 2500 140 2000 140 2000 88 1250 88 1250

Max. End Load A kN / Lbs mm / in 50 90 11070 3.54 73.2 103 16220 4.06 108.6 122 24040 4.80 179.5 157 39740 6.18 311.3 218 68910 8.58 527.6 275 116790 10.83 514.8 334 113400 13.15 724.7 390 159510 15.35

Dimensions B mm / in 150 5.90 168 6.61 188 7.40 222 8.74 295 11.61 364 14.33 424 16.70 480 18.93

Bolt / Nut C Size Torque mm / in No. in N-m / Lbs - Ft 49 80 - 120 2 ⅝ x 2¾ 1.92 60 - 90 49 80 - 120 2 ⅝ x 2¾ 1.92 60 - 90 51 80 - 120 2 ⅝ x 2¾ 2.00 60 - 90 55 100 - 135 2 ¾ x 4¾ 2.17 74 - 170 57 170 - 275 2 ⅞ x 5½ 2.25 125 - 200 70 275 - 400 2 1 x 5½ 2.75 200 - 300 75 275 - 400 2 1 x 5½ 2.95 200 - 300 75 275 - 400 2 1 x 5½ 2.95 200 - 300

Bolt Weight Kgs / Lbs 1.6 3.4 1.7 3.8 2.2 4.8 3.8 8.4 8.0 17.6 10.9 24.0 14.2 31.2 16.7 36.7

*Pressures quoted are based on EP cut grooved XS (Sch. 80) pipe.

EP Cut-Groove specification 1. EP cut-grooves are for plastic coated or

A

O.D.

B

T

the coating or lining and or create flared

Nominal Size Basic mm / in mm / in 50 60.3 2 2.375 65 73.0 2½ 2.875 80 88.9 3 3.500 100 114.3 4 4.500 150 168.3 6 6.625 200 219.1 8 8.625 250 273.0 10 10.750 300 323.9 12 12.750


Shurt XH-70EP couplings only. Do

not roll groove pipe, which can damage

C

pipe ends.

d

cement lined pipe to be connected with

2. Always use plain-end square cut pipe. Do not use beveled end pipe. 3. Always use an EP gasket with a XH-70EP coupling. Do not use a standard gasket. 4. The gasket seating area shall be free from deep scores, marks, or ridges that could prevent a positive seal.

Pipe O. D. Tolerance mm / in mm / in +0.61 -0.61 +0.024 -0.024 +0.74 -0.74 +0.029 -0.29 +0.89 -0.79 +0.035 -0.031 +1.14 -0.79 +0.045 -0.031 +1.60 -0.79 +0.063 -0.031 +1.60 -0.79 +0.063 -0.031 +1.60 -0.79 +0.063 -0.031 +1.60 -0.79 +0.063 -0.031


Gasket Seat A Basic Tol. mm / in ± 14.27 ±0.25 0.562 ±0.010 14.27 ±0.25 0.562 ±0.010 14.27 ±0.25 0.562 ±0.010 15.37 ±0.38 0.605 ±0.015 15.37 ±0.38 0.605 ±0.015 18.14 ±0.38 0.714 ±0.015 18.14 ±0.38 0.714 ±0.015 18.14 ±0.38 0.714 ±0.015

Groove Width B Basic Tol. mm / in +0.25/+0.010 6.48 -0.13 0.255 -0.005 6.48 -0.13 0.255 -0.005 6.48 -0.13 0.255 -0.005 7.75 -0.13 0.305 -0.005 7.75 -0.13 0.305 -0.005 10.16 -0.25 0.400 -0.010 10.16 -0.25 0.400 -0.010 10.16 -0.25 0.400 -0.010

Groove Dia. C Basic Tol. mm / in +0/+0 57.15 -0.38 2.250 -0.015 69.09 -0.46 27.20 -0.018 84.94 -0.46 3.344 -0.018 110.08 -0.51 4.334 -0.020 163.96 -0.56 6.455 -0.022 214.4 -0.64 8.441 -0.025 268.28 -0.69 10.562 -0.027 318.29 -0.76 12.531 -0.030

www.shurt.com

Grv. Depth d (ref.) 1.60 0.063 1.98 0.078 1.98 0.078 2.11 0.083 2.16 0.085 2.34 0.092 2.39 0.094 2.77 0.109

Min. Wall thickness T mm / in 3.91 0.154 4.78 0.188 4.78 0.188 5.16 0.203 5.56 0.219 6.05 0.238 6.35 0.250 7.09 0.279

Catalog 2011

Flange Adapters Shurt offers a variety of flange adapters 2” through 24” (50mm – 600mm) to transition

Flange Segment

Flange Segment

from a flanged system to a grooved system.

Gasket

Flange drillings available include ANSI Class 125/150, Class 300, PN 10/16 and BS 10 Table E.

Hinged

Gasket

Factory Supplied Bolts & Nuts

Factory Supplied Bolt & Nut

Flange adapters 2” through 12” are supplied hinged as a single assembly while 14” through 24” (7041N) are supplied with two independent segments and a draw kit. Always use factory-supplied bolts and nuts

7041N 14" ~ 24" (With a draw kit)

7041 2" ~ 12"

to assemble flange segments. The use of other bolts may cause t failure.

14” – 24”: Supplied with a draw kit

Important Notes 1. Models 7041 and 7043 flange adapters

2. The Model 7041 flange adapter has small

interfere with the valve actuator or the

require a hard flat face for effective sealing.

triangular teeth inside the key shoulder to

mounting pad of the actuator.

When the mating surface is not adequate

prevent the pipe from rotating. The teeth

as with the serrated faces of some valves or

should be ground off when mating to a

5. Bolt tightening sequence: Like a regular

rubber-faced wafer valves, a sandwich plate

rubber-lined flange, plastic pipe and or light

flange t, it is important to make flange

(Model 49, see page 30) must be used.

wall pipe.

faces parallel. Tighten nuts alternately in the sequence of diagonally

#7041 Flange

Flange to mate (Rubber surface)

3. Models 7041 and 7043 flange adapters

opposite pairs as shown below until the

shall not be used as anchor points for tie-

flange faces meet and make a metal-to-

rods across non-restrained ts.

metal . 1

4. When assembling a Model 7041 or 7043 flange adapter against a butterfly valve or ball valve, make sure that the outside Sandwich Plate

6

Interfere #7041 Flange

1

4

Regular Flange Gasket

Butterfly Valve 6 Hinged


7 2

1

Hinged 5

8 3

6

2

12

5

4 10

7

Hinged

Flange to mate (Serrated face) 8

Sandwich Plate

3

Rubber faced or lined

9

4

3

10

7 6

Hinged

www.shurt.com

2

5

8

4

diameter of the flange adapters do not

1

12

5

8

11


2

11

Catalog 2011

MODEL

7041 FLANGE ADAPTER - ANSI Class 125/150 The Shurt Model 7041 flange adapters 2” through 12” are supplied hinged as a single assembly, while 14” - 24” (7041N) are and a draw kit.

E



300 psi @100°F 20 Bar @38°C


Class 150

DE

Nominal Size mm / in 50 2 65 2½ 80 3 100 4 125 5 150 6 200 8 250 10 300 12 350 14 400 16 450 18 500 20 550 22 600 24

Pipe O. D. mm / in 60.3 2.375 73.0 2.875 88.9 3.500 114.3 4.500 141.3 5.563 168.3 6.625 219.1 8.625 273.0 10.750 323.9 12.750 355.6 14.000 406.4 16.000 457.2 18.000 508.0 20.000 558.8 22.000 609.6 24.000

Max. Working Pressure Bar / PSI 20 300 20 300 20 300 20 300 20 300 20 300 20 300 20 300 20 300 20 300 20 300 20 300 20 300 20 300 20 300

The tables show standard torque

values for proper assembly of Shurt flange adapters. Use a torque wrench so that all the nuts are tightened equally with a same torque value. Shurt flange

adapters are sealed with elastic (rubber) gaskets, which require much lower torques than those that utilize metallic gaskets.

2” - 12” (hinged)

Max. End Load A kN / Lbs mm / in 5.71 152 1330 6.00 8.37 178 1950 7.00 12.41 190 2880 7.50 20.51 229 4770 9.00 31.35 254 7290 10.00 44.47 279 10340 11.00 75.37 343 17520 13.50 117.01 406 27210 16.00 164.71 482 38280 19.00 198.53 533 46160 21.00 259.3 597 60290 23.50 328.18 635 76300 25.80 405.18 699 94200 27.50 490.24 749 113980 29.50 583.43 813 135650 32.00

Required bolt torque

©Copyright 2011 Shurt

Dimensions B C mm / in mm / in 121 19 4.75 0.75 140 22 5.50 0.87 152 24 6.00 0.94 191 24 7.50 0.94 216 24 8.50 0.94 241 25 9.50 1.00 298 28 11.75 1.12 362 30 14.25 1.18 432 32 17.00 1.25 476 37 18.75 1.44 540 37 21.25 1.44 578 40 22.75 1.56 635 43 25.00 1.69 692 48 27.25 1.90 749 49 29.50 1.94

7041N 14” - 24” (supplied with a draw kit)

Sealing Surface Bolts D E Size mm / in mm / in No. in 60 87 4 ⅝ 2.36 3.42 73 102 4 ⅝ 2.87 4.00 89 116 4 ⅝ 3.50 4.56 114 141 8 ⅝ 4.50 5.56 141 171 8 ¾ 5.56 6.73 168 198 8 ¾ 6.62 7.79 219 254 8 ¾ 8.62 10.00 273 308 12 ⅞ 10.75 12.12 324 359 12 ⅞ 12.75 14.13 356 416 12 1 14.0 16.40 406 467 16 1 16.0 18.40 457 508 16 1⅛ 18.0 20.00 508 572 20 1⅛ 20.0 22.50 551 588 20 1¼ 21.70 23.15 602 635 20 1¼ 23.70 25.0

Weight Kgs / Lbs 1.8 4.0 2.3 5.1 2.8 6.2 3.8 8.3 4.7 10.3 5.0 11.1 7.8 17.2 11.7 25.7 17.1 37.6 28.0 61.7 35.0 77.1 39.0 86.0 49.5 109.1 60.4 133.1 71.5 157.6

Required Torque for Model 7041 Flange Adapters (ANSI Class 125/150)

Required Torque for Model 7041 Flange Adapters (PN 10/16)

Nom. Size inch 2" 2½" 3" 4" 5" 6" 8" 10" 12" 14" 16" 18" 20" 24"

Nom. Size mm 50 65 80 100 125 150 200 250 300 350 400 450 500 600

( ): No. of bolts

28

B

D

B

Tooth

*Working pressure is based on roll- or cut-grooved standard wall carbon steel pipe. *Hydrostatic Shell Test: 450 psi (30 bar) per ANSI B16.5.

C

A


C

A

supplied with two independent segments


Bolt Size inch ⅝ (4) ⅝ (4) ⅝ (4) ⅝ (8) ¾ (8) ¾ (8) ¾ (8) ⅞ (12) ⅞ (12) 1 (12) 1 (16) 1⅛(16) 1⅛ (20) 1¼ (20)

Required Torque N-m Lbs-Ft 30 - 50 22 - 37 30 - 50 22 - 37 40 - 68 30 - 50 40 - 68 30 - 50 40 - 68 30 - 50 40 - 68 30 - 50 68 - 90 50 - 66 80 - 120 59 - 89 80 - 120 59 - 89 100 - 135 74 - 100 100 - 135 74 - 100 110 - 160 81 - 118 110 - 160 81 - 118 135 - 190 100 - 140

Bolt Size mm M16 (4) M16 (4) M16 (8) M16 (8) M20 (8 ) M20 (8) M20 (12) M24 ( 12) M24 (12) M24 (16) M27 (16) M27 (20) M30 (20) M33 (20)

( ): No. of bolts

www.shurt.com

Required Torque N-m Lbs-Ft 30 - 50 22 - 37 30 - 50 22 - 37 40 - 68 30 - 50 40 - 68 30 - 50 40 - 68 30 - 50 40 - 68 30 - 50 68 - 90 50 - 66 80 - 120 59 - 89 80 - 120 59 - 89 100 - 135 74 - 100 100 - 135 74 - 100 110 - 160 81 - 118 110 - 160 81 - 118 135 - 190 100 - 140

Catalog 2011

MODEL

7041 FLANGE ADAPTER - PN 10 / PN 16 The Shurt Model 7041 flange adapter

flange adapters are supplied hinged as a

allows for a direct connection with PN 10/16

single assembly, while 14” - 24” (7041N) are

flanges. The two-segment design provides

supplied with two independent segments

an easy and fast installation. 2” through 12”

and a draw kit.

Pressure-Temperature Rating Nom. Rating PN 16



225 psi @100°F 16 Bar @38°C


A

E D E

*Working pressure is based on roll- or cut-grooved standard wall carbon steel pipe. *Hydrostatic Shell Test: 1.5 times the working pressure, nonshock cold water.

Nominal Size mm 50 65 80 100 150 150 200 250 300 350 400 450 500 600

Pipe O. D. mm 60.3 76.1 88.9 114.3 165.1 168.3 219.1 273.0 323.9 355.6 406.4 457.2 508.0 609.6

Max. Working Pressure Bar 16 16 16 16 16 16 16 16 16 16 16 16 16 16

B

D

B

Tooth 2” - 12” (hinged)

C

A

C

Max. End Load A kN mm 4.6 165 7.3 185 9.9 200 16.4 220 34.2 285 35.6 285 60.3 340 93.6 405 131.8 460 158.8 520 207.4 580 262.5 640 324.0 715 466.7 840

7041N 14” - 24” (supplied with a draw kit)

Dimensions B C mm mm 125 22 145 22 160 24 180 24 240 24 240 24 295 24 355 26 410 28 470 30 525 32 585 36 650 36 770 40

Sealing Surface Bolts D E Size mm mm mm No. 60 87 M16 4 76 105 M16 4 89 116 M16 8 114 141 M16 8 165 195 M20 8 168 198 M20 8 219 254 M20 12 273 308 M24 12 324 359 M24 12 356 416 M24 16 406 467 M27 16 457 508 M27 20 508 572 M30 20 610 706 M33 20

Weight Kgs 2.3 2.6 3.2 3.4 5.1 4.6 7.8 11.4 13.7 23.0 28.0 42.5 47.0 73.0

Note: 2" - 6" flange drilling to PN10 / PN16 and 8" and above to PN16. See page 28 for required bolt torque.

MODEL

7041 FLANGE ADAPTER - BS 10-E The Shurt Model 7041 flange adapter

through 12” flange adapters are supplied

allows for a direct connection with BS 10

hinged as a single assembly, while 14” - 24”

Table E flanges. The two-segment design

(7041N) are supplied with two independent

provides an easy and fast installation. 2”

segments and a draw kit. A

Pressure-Temperature Rating Nom. Rating PN 14



200 psi @100°F 14 Bar @38°C


*Working pressure is based on roll- or cut-grooved standard wall carbon steel pipe. *Hydrostatic Shell Test: 1.5 times the working pressure, nonshock cold water.

E

Nominal Size mm 65 80 100 125 150 200 250 300 350 400 450 500 600

Pipe O. D. mm 76.1 88.9 114.3 139.7 165.1 219.1 273.0 323.9 355.6 406.4 457.2 508.0 609.6

Max. Working Pressure Bar 14 14 14 14 14 14 14 14 14 14 14 14 14

Max. End Load A kN mm 6.36 165 8.69 184 14.36 216 21.45 254 29.96 279 52.76 337 81.91 406 115.30 457 138.97 527 181.51 578 229.73 641 283.61 705 408.4 826


B

D

B

Tooth

2” - 12” (hinged)

C

A

DE

C

Dimensions B C mm mm 127 22 146 24 178 24 210 24 235 24 292 29 356 30 406 32 470 32 521 32 584 36 641 38 756 42

7041N 14” - 24” (supplied with a draw kit) Sealing Surface Bolts D E Size mm mm No. in 76 105 4 ⅝ 89 116 4 ⅝ 114 141 8 ⅝ 140 170 8 ⅝ 165 195 8 ¾ 219 254 8 ¾ 273 308 12 ¾ 324 359 12 ⅞ 356 416 12 ⅞ 406 467 12 ⅞ 457 508 16 ⅞ 508 572 16 ⅞ 610 706 16 1⅛

www.shurt.com

Weight Kgs 2.5 3.4 4.0 4.5 5.0 8.4 10.8 12.0 20.8 21.0 28.9 38.1 54.6


Catalog 2011

MODEL

7043 FLANGE ADAPTER - ANSI CLASS 300 The Shurt Model 7043 flange adapter

flange adapters are supplied hinged as

allows for direct connection of a grooved

a single assembly, while large sizes are

system to ANSI Class 300 flanged

supplied with separate segments.

components. 2" through 8" Model 7043 X




750 psi @100°F 52 Bar @38°C


Class 300

DE

Z

Y

*Working pressure is based on roll- or cut-grooved standard wall carbon steel pipe. *Hydrostatic Shell Test: 1125 psi (77 bar) per ANSI B16.5.

Nominal Size mm / in 50 2 65 2½ 80 3 100 4 125 5 150 6 200 8 250 10 300 12

Pipe O. D. mm / in 60.3 2.375 73.0 2.875 88.9 3.500 114.3 4.500 141.3 5.563 168.3 6.625 219.1 8.625 273.0 10.750 323.9 12.750

Max. Working Pressure Bar / PSI 52 750 52 750 52 750 52 750 52 750 52 750 52 750 52 750 52 750

Max. End Load X kN / Lbs mm / in 14.84 165 3320 6.50 21.75 191 4870 7.50 32.28 210 7210 8.25 53.33 254 11920 10.00 81.50 279 18220 11.00 115.62 318 25840 12.50 195.96 381 43800 15.00 304.23 445 68040 17.50 428.25 521 95710 20.50

Dimensions Y Z mm / in mm / in 127 24 5.00 0.94 149 27 5.88 1.06 168 30 6.63 1.19 202 33 7.95 1.31 235 37 9.25 1.44 270 38 10.63 1.50 330 43 13.00 1.69 387 49 15.25 1.94 451 51 17.75 2.00

Sealing Surface Bolts D E Size mm / in mm / in No. in 60 87 8 ⅝ 2.36 3.41 73 99 8 ¾ 2.88 3.91 89 115 8 ¾ 3.50 4.53 114 140 8 ¾ 4.50 5.53 141 171 8 ¾ 5.56 6.72 168 198 12 ¾ 6.63 7.78 219 252 12 ⅞ 8.63 9.94 273 313 16 1 10.75 12.31 324 364 16 1⅛ 12.75 14.31

Weight Kgs / Lbs 2.4 5.3 3.6 7.9 4.6 10.0 7.8 17.3 9.6 21.2 12.5 27.6 16.4 36.2 25.8 56.9 35.2 77.7

MODEL

49 SANDWICH PLATE The Model 7041 and 7043 flange adapters

Material: Mild-steel, electro-zinc plated.

require a hard flat surface for effective

Stainless steel, type 304 or 316 is available

gasket sealing. A sandwich plate is required

on request.

and should always be used when the mating surface is not adequate as with the serrated faces of some valves or the rubber-faced or rubber-lined flange adapters of a wafer valve. E D

Sandwich plate



Nominal Size mm / in 50 2 65 2½ 80 3 100 4 125 5 150 6 200 8 250 10 300 12 350 14 400 16 450 18 500 20 600 24

www.shurt.com

E mm / in 95 3.74 118 4.65 130 5.12 158 6.22 188 7.40 216 8.50 271 10.67 326 12.83 381 15.00 414 16.30 470 18.50 533 21.00 584 23.00 692 27.25

D mm / in 54 2.13 67 2.64 81 3.19 105 4.13 128 5.00 155 6.10 205 8.07 258 10.15 305 12.00 337 13.25 387 15.25 438 17.25 489 19.25 590 23.25

Catalog 2011

MODEL

7180 UNIVERSAL FLANGE ADAPTER The Model 7180 Universal Flange Adapter

Pressure-Temperature Rating

provides a rigid transition from a flanged

Nom. Rating

component to a grooved system. The single unit is compatible for a range of flange types including ANSI Class 125/150, PN10, PN16, and JIS 10K.

Class 150



300 psi @100°F 20 Bar @38°C



Z

XY

D

L Nominal Pipe ANSI Size O.D. L X 125 / 150 mm / in mm / in mm / in mm / in mm / in 50 60.3 64 165 121 2 2.375 2.50 6.50 4.75 65 73.0 70 185 140 2½ 2.875 2.75 7.28 5.50 76.1 70 185 140 76.1mm 3.000 2.75 7.28 5.50 80 88.9 70 200 152 3 3.500 2.75 7.87 6.00 100 114.3 76 229 191 4 4.500 3.00 9.00 7.50 139.7 76 250 216 139.7mm 5.500 3.00 9.84 8.50 125 141.3 76 250 216 5 5.563 3.00 9.84 8.50 165.1 76 291 241 165.1mm 6.500 3.00 11.46 9.50 150 168.3 89 291 241 6 6.625 3.50 11.46 9.50 200 219.1 102 343 298 8 8.625 4.00 13.50 11.75 216.3 102 343 298 200 JIS 8.516 4.00 13.50 11.75

Y : Flange Drilling Bolts Size PN JIS BS 10,16 10K 10E Z Dia No. Weight mm / in mm / in mm / in mm / in mm / in Kgs / Lbs 125 120 114 16 M16 4 2.30 4.92 4.72 4.49 0.63 ⅝ 4 5.10 145 140 127 16 M16 4 2.96 5.70 5.50 5.00 0.63 ⅝ 4 6.53 145 140 127 16 M16 4 2.90 5.70 5.50 5.00 0.63 ⅝ 4 6.40 160 150 146 16 M16 8 3.39 6.30 5.90 5.75 0.63 ⅝ 4 7.47 180 175 178 16 M16 8 3.85 7.09 6.89 7.00 0.63 ⅝ 8 8.49 210 210 210 22 M16 / M20 8 6.50 8.27 8.27 8.27 0.87 ⅝ / ¾ 8 14.33 210 210 --- 22 M16 / M20 8 6.50 8.27 8.27 --- 0.87 ⅝ / ¾ 8 14.33 240 240 235 24 M20 8 6.30 9.45 9.45 9.30 0.94 ¾ 8 13.86 240 240 --- 24 M20 8 5.72 9.45 9.45 --- 0.94 ¾ 8 12.58 295 290 292 29 M20 8 / 12 13.65 11.61 11.42 11.50 1.14 ¾ 8 / 12 30.09 295 290 --- 29 M20 8 / 12 13.65 11.61 11.42 --- 1.14 ¾ 8 / 12 30.09

MODEL

7181 UNIVERSAL REDUCING FLANGE ADAPTER The Model 7181 Universal Reducing Flange


Adapter provides a rigid transition between a

Nom. Rating

flanged piping system and a one or two-size reduced grooved system without the need of a concentric reducer. The flange drilling is compatible to ANSI 125/150, PN10/16, BS-10E and JIS 10K.

Class 150



300 psi @100°F 20 Bar @38°C


Z


XY

D

L Nominal Pipe Size OD L X Z mm / in mm / in mm / in mm / in mm / in 80 x 50 88.9 x 60.3 75.0 208.0 16.0 3 x 2 3.500 x 2.375 2.95 8.19 0.63 100 x 65 114.3 x 73.0 76.0 225.5 16.0 4 x 2½ 4.500 x 2.875 3.00 8.88 6.30 114.3 x 76.1 76.0 225.5 16.0 100 x 76.1mm 4.500 x 3.000 3.00 8.88 6.30 100 x 80 114.3 x 88.9 75.0 225.5 16.0 4 x 3 4.500 x 3.500 2.95 8.88 0.63 150 x 100 168.3 x 114.3 75.0 291.0 24.0 6 x 4 6.625 x 4.500 2.95 11.46 0.95


Y: Flange Drilling ANSI PN JIS 125 / 150 10, 16 10K D mm / in mm / in mm / in mm / in 152 160 150 60.3 8.00 6.30 5.90 2 191 180 175 73.0 7.52 7.09 6.89 2.875 191 180 175 76.1 7.52 7.09 6.89 3.000 191 180 175 88.9 7.50 7.09 6.89 3 241 240 240 114.3 9.50 9.45 9.45 4

Bolts Dia. No. mm / in M16 8 ⅝ M16 8 ⅝ M16 8 ⅝ M16 8 ⅝ M20 8 ¾

www.shurt.com

Weight Kgs / Lb 2.70 5.95 4.00 8.80 4.00 8.80 3.45 7.61 7.08 15.61


Catalog 2011

MODEL

7170 FLANGE ADAPTeR - ANSI CLASS 125/150 The Model 7170 Flange Adaptor provides a rigid transition between ANSI class 125/150 flanged components and a grooved system. Z



300 psi @100°F 20 Bar @38°C


Class 150


Bolt Hole

D

Nom. Rating

X Y


L

Nominal Pipe Bolt Bolt Hole Size X Y Z Size Dia. No. mm / in mm / in mm / in mm / in in in 250 406.4 362.0 30.0 ⅞ 1 12 10 16.00 14.25 1.18 300 483.0 432.0 32.0 ⅞ 1 12 12 19.00 17.00 1.25 350 533.0 476.3 35.0 1 1⅛ 12 14 21.00 18.75 1.38 400 597.0 539.7 37.0 1 1⅛ 16 16 23.50 21.25 1.46 450 635.0 577.8 40.0 1⅛ 1¼ 16 18 25.00 22.75 1.57 500 699.0 635.0 43.0 1⅛ 1¼ 20 20 27.50 25.00 1.69 600 813.6 749.3 48.0 1¼ 1⅜ 20 24 32.00 29.50 1.89



D mm / in 273.0 10.75 323.9 12.75 355.6 14.00 406.4 16.00 457.2 18.00 508.0 20.00 609.6 24.00

www.shurt.com

L mm / in 127.0 5.00 127.0 5.00 127.0 5.00 127.0 5.00 140.0 5.50 152.0 6.00 152.0 6.00

Weight Kgs / Lbs 22.0 48.4 28.0 61.6 49.5 108.9 50.0 110 62.5 137.5 72.0 158.4 99.5 218.9

Catalog 2011

Mechanical Tees

Hole-cutting

Shurt mechanical tees provide a fast

The hole-cut method of pipe preparation

and easy mid-point branch outlet, eliminating

is required when using mechanical tees,

the need for welding or the use of multiple

mechanical crosses, and saddle-lets. The

fittings. The Model M21 features a female

method of pipe preparation requires the

threaded outlet and M22 features a grooved

cutting or drilling of a specified hole size on

end outlet. Model 7721 (female threaded

the centerline of the pipe. Always use the

outlet) and 7722 (grooved end outlet) are

correct hole saw size as shown in Table 1

available in 8” sizes. The Model 723 Saddlelet features a compact-design for making

A

direct connections to sprinkler heads, drop nipples and or gauges.

Ridgid Model No. HC-300 Hole Cutting Tool 16mm ( ⅝" )

and Table 1-b and never use a torch for cutting a hole. After the hole has been cut all rough edges must be removed and the area within 5/8” (16mm) of the hole Upper Housing

Gasket

Locating Collar

Alignment Tab

smooth surface, free of any indentations or projections that could affect proper gasket sealing. The area within the “A” dimension should also be inspected and must be free of dirt, scale or any imperfection that could

Nut Bolt

Bolt Pad

should be inspected to ensure a clean

affect proper seating or assembly of the fitting. Hole Size: The hole sizes are dictated by the branch size of the mechanical tee.

Lower Housing

Table 1 Hole Sizes for Mechanical Tees When bolts are tightened with a proper torque, the outlet housing makes metal to metal with the outer surface of the pipe. Metal-to-metal

Gap It is normal to see bolt pad gaps

unit: mm/in

Branch Size 15, 20, 25 ½, ¾, 1 32, 40 1¼, 1½ 50 2 65 2½ 80 3 100 4

Hole Dimensions Surface Hole Saw Max dia. Preparation Size Allowed “A” 38 41 89 1½ 1⅝ 3½ 51* 54* 102 2 2⅛ 4 64 67 114 2½ 2⅝ 4½ 70 73 121 2¾ 2⅞ 4¾ 89 92 140 3½ 3⅝ 5½ 114 118 165 4½ 4⅝ 6½

*See Table 1-b for exception.`

Table 1-b Exception The hole must be cleanly cut using the correct size hole-saw and shall have a smooth edge. Never use a torch for cutting a hole.

Hole Dimensions Surface Run x Branch Hole Saw Max dia. Preparation Size Allowed “A” 50 x 32 / 50 x 40 45 47 102 2 x1¼ / 2 x 1½ 1¾ 1⅞ 4


www.shurt.com


Catalog 2011

MODEL

M21 MECHANICAL TEE

FEMALE THREADED OUTLET Threads are NPT per ANSI B1.20.1 or BSPT per ISO 7. UL/FM working pressure is 20 bar (300 psi). The Model 7721 is available in 8" sizes. Pressure-Temperature Rating Nom. Rating



300 psi @100°F 20 Bar @38°C


Class 150

*Working pressure is based on standard wall carbon steel pipe. *Proof test pressure: 1.5 times the working pressure, non-shock cold water. *Burst pressure is engineered minimum 3 times the working pressure.

Nominal Size Run x Branch mm / in 50 x 15 2 x ½ 50 x 20 2 x ¾ 50 x 25 2 x 1 50 x 32 2 x 1¼ 50 x 40 2 x 1½ 65 x 15 2.5 x ½ 65 x 20 2.5 x ¾ 65 x 25 2.5 x 1 65 x 32 2.5 x 1¼ 65 x 40 2.5 x 1½ 76.1 x 15 76.1 x 20 76.1 x 25 76.1 x 32 76.1 x 40 80 x 15 3 x ½ 80 x 20 3 x ¾ 80 x 25 3 x 1 80 x 32 3 x 1¼ 80 x 40 3 x 1½ 80 x 50 3 x 2 100 x 15 4 x ½ 100 x 20 4 x ¾ 100 x 25 4 x 1 100 x 32 4 x 1¼ 100 x 40 4 x 1½

Pipe O. D. mm / in 60.3 x 21.3 2.375 x 0.840 60.3 x 26.7 2.375 x 1.050 60.3 x 33.4 2.375 x 1.315 60.3 x 42.2 2.375 x 1.660 60.3 x 48.3 2.375 x 1.900 73.0 x 21.3 2.875 x 0.840 73.0 x 26.7 2.875 x 1.050 73.0 x 33.4 2.875 x 1.315 73.0 x 42.2 2.875 x 1.660 73.0 x 48.3 2.875 x 1.900 76.1 x 21.3 3.000 x 0.840 76.1 x 26.7 3.000 x 1.050 76.1 x 33.4 3.000 x 1.315 76.1 x 42.2 3.000 x 1.660 76.1 x 48.3 3.000 x 1.900 88.9 x 21.3 3.500 x 0.840 88.9 x 26.7 3.500 x 1.050 88.9 x 33.4 3.500 x 1.315 88.9 x 42.2 3.500 x 1.660 88.9 x 48.3 3.500 x 1.900 88.9 x 60.3 3.500 x 2.375 114.3 x 21.3 3.500 x 0.840 114.3 x 26.7 4.500 x 1.050 114.3 x 33.4 4.500 x 1.315 114.3 x 42.2 4.500 x 1.660 114.3 x 48.3 4.500 x 1.900

Hole Dia. +3.2, -0 / +0.13, -0 mm / in 38 1.50 38 1.50 38 1.50 [45] [1.75] [45] [1.75] 38 1.50 38 1.50 38 1.50 51 2.00 51 2.00 38 1.50 38 1.50 38 1.50 51 2.00 51 2.00 38 1.50 38 1.50 38 1.50 51 2.00 51 2.00 64 2.50 38 1.50 38 1.50 38 1.50 51 2.00 51 2.00

C A

D T

B

T* A mm / in mm / in 50 63.5 1.97 2.50 50 63.5 1.97 2.50 47 63.5 1.85 2.50 52 73.0 2.05 2.87 52 76.2 2.08 3.00 56 69.9 2.20 2.75 56 69.9 2.20 2.75 53 69.9 2.09 2.75 58 76.2 2.28 3.00 58 76.2 2.28 3.00 56 69.9 2.20 2.75 56 69.9 2.20 2.75 53 69.9 2.09 2.75 58 76.2 2.28 3.00 58 76.2 2.28 3.00 60 77.8 2.36 3.06 59 77.8 2.32 3.06 61 77.8 2.40 3.06 65 82.6 2.56 3.25 71 88.9 2.80 3.50 70 88.9 2.76 3.50 72 93.7 2.83 3.69 71 93.7 2.79 3.69 73 93.7 2.87 3.69 78 92.1 3.07 3.63 84 92.1 3.31 3.63

Dimensions B C D mm / in mm / in mm / in 38.1 115.9 81 1.50 4.56 3.19 38.1 115.9 81 1.50 4.56 3.19 38.1 115.9 81 1.50 4.56 3.19 38.1 115.9 84 1.50 4.56 3.31 38.1 115.9 84 1.50 4.56 3.31 44.5 141.3 81 1.75 5.56 3.19 44.5 141.3 81 1.75 5.56 3.19 44.5 141.3 81 1.75 5.56 3.19 44.5 141.3 94 1.75 5.56 3.70 44.5 141.3 94 1.75 5.56 3.70 46.1 144.5 81 1.81 5.69 3.19 46.1 144.5 81 1.81 5.69 3.19 46.1 144.5 81 1.81 5.69 3.19 46.1 144.5 94 1.81 5.69 3.70 46.1 144.5 94 1.81 5.69 3.70 53.2 157.2 81 2.09 6.19 3.19 53.2 157.2 81 2.09 6.19 3.19 53.2 157.2 81 2.09 6.19 3.19 53.2 157.2 94 2.09 6.19 3.70 53.2 157.2 94 2.09 6.19 3.70 53.2 157.2 108 2.09 6.19 4.25 66.7 182.6 79.4 2.63 7.19 3.13 66.7 182.6 79.4 2.63 7.19 3.13 66.7 182.6 79.4 2.63 7.19 3.13 66.7 182.6 101.6 2.63 7.19 4.00 66.7 182.6 101.6 2.63 7.19 4.00

1. Hole diameters listed are suggested hole saw diameters. 2. *T: Take-out (Center of run to end of pipe to be engaged) 3. Special caution is required to some exceptional hole sizes shown in [ ].



Bolt Size mm / in M10 x 55 ⅜ x 2⅛ M10 x 55 ⅜ x 2⅛ M10 x 55 ⅜ x 2⅛ M10 x 55 ⅜ x 2⅛ M10 x 55 ⅜ x 2⅛ M12 x 60 ½ x 2⅜ M12 x 60 ½ x 2⅜ M12 x 60 ½ x 2⅜ M12 x 60 ½ x 2⅜ M12 x 60 ½ x 2⅜ M12 x 60 ½ x 2⅜ M12 x 60 1/2 x 2-3/8 M12 x 60 ½ x 2⅜ M12 x 60 ½ x 2⅜ M12 x 60 ½ x 2⅜ M12 x 75 ½ x 3 M12 x 75 ½ x 3 M12 x 75 ½ x 3 M12 x 75 ½ x 3 M12 x 75 ½ x 3 M12 x 75 ½ x 3 M12 x 75 ½ x 3 M12 x 75 ½ x 3 M12 x 75 ½ x 3 M12 x 75 ½ x 3 M12 x 75 ½ x 3

Weight Kgs / Lbs 0.99 2.18 1.01 2.22 1.09 2.40 1.26 2.77 1.37 3.01 1.20 2.60 1.20 2.70 1.30 2.86 1.46 3.21 1.56 3.43 1.20 2.64 1.20 2.64 1.30 2.86 1.46 3.21 1.56 3.43 1.44 3.17 1.46 3.21 1.53 3.37 1.81 3.98 1.88 4.14 2.07 4.55 1.63 3.59 1.64 3.61 1.70 3.74 1.90 4.18 2.04 4.49

Continued on next page

www.shurt.com

Catalog 2011

MODEL

M21 & 7721 MECHANICAL TEES FEMALE THREADED OUTLET The Shurt Model M21 & 7721 mechanical

C

tees provides a fast and easy mid-pipe threaded branch outlet. Threads are NPT per ANSI B1.20.1 or BSPT per ISO 7. UL/FM working pressure is 20 bar (300 psi).

A

D T

B

Continued from previous page

Nominal Size Run x Branch mm / in 100 x 50 4 x 2 100 x 65 4 x 2½ 100 x 76.1 100 x 80 4 x 3 139.7 x 50 139.7 x 76.1 139.7 x 80 125 x 50 5 x 2 125 x 65 5 x 2½ 125 x 80 5 x 3 165.1 x 32 165.1 x 40 165.1 x 50 165.1 x 65 165.1 x 76.1 165.1 x 80 165.1 x 100 150 x 32 6 x 1¼ 150 x 40 6 x 1½ 150 x 50 6 x 2 150 x 65 6 x 2½ 150 x 76.1 150 x 80 6 x 3 150 x 100 6 x 4

Pipe O. D. mm / in 114.3 x 60.3 4.500 x 2.375 114.3 x 73.0 4.500 x 2.875 114.3 x 76.1 4.500 x 3.000 114.3 x 88.9 4.500 x 3.500 139.7 x 60.3 5.500 x 2.375 139.7 x 76.1 5.500 x 3.000 139.7 x 88.9 5.500 x 3.500 141.3 x 60.3 5.563 x 2.375 141.3 x 73.0 5.563 x 2.875 141.3 x 88.9 5.563 x 3.500 165.1 x 42.2 6.500 x 1.660 165.1 x 48.3 6.500 x 1.900 165.1 x 60.3 6.500 x 2.375 165.1 x 73.0 6.500 x 2.875 165.1 x 76.1 6.500 x 2.875 165.1 x 88.9 6.500 x 3.500 165.1 x 114.3 6.500 x 4.500 168.3 x 42.2 6.625 x 1.660 168.3 x 48.3 6.625 x 1.900 168.3 x 60.3 6.625 x 2.375 168.3 x 73.0 6.625 x 2.875 168.3 x 76.1 6.625 x 2.875 168.3 x 88.9 6.625 x 3.500 168.3 x 114.3 6.625 x 4.500

Hole Dia. +3.2, -0 / +0.13, -0 mm / in 64 2.50 70 2.75 70 2.75 89 3.50 64 2.50 70 2.75 89 3.50 64 2.50 70 2.75 89 3.50 51 2.00 51 2.00 64 2.50 70 2.75 70 2.75 89 3.50 114 4.50 51 2.00 51 2.00 64 2.50 70 2.75 70 2.75 89 3.50 114 4.50

T* A mm / in mm / in 83 101.6 3.27 4.00 73 101.6 2.87 4.00 73 101.6 2.87 4.00 84 104.8 3.31 4.13 83 120.7 3.27 4.75 93 120.7 3.67 4.75 97 127.0 3.82 4.75 83 120.7 3.27 4.75 93 120.7 3.67 4.75 97 127.0 3.82 4.75 112 130.2 4.41 5.13 112 130.2 4.41 5.13 111 130.2 4.37 5.13 101 130.2 3.98 5.13 101 130.2 3.98 5.13 110 139.7 4.33 5.50 113 146.1 4.45 5.75 112 130.2 4.41 5.13 112 130.2 4.41 5.13 111 130.2 4.37 5.13 101 130.2 3.98 5.13 101 130.2 3.98 5.13 110 139.7 4.33 5.50 113 146.1 4.45 5.75

Dimensions B C D mm / in mm / in mm / in 66.7 182.6 101.6 2.63 7.19 4.00 66.7 182.6 112.7 2.63 7.19 4.44 66.7 182.6 112.7 2.63 7.19 4.44 66.7 182.6 128.6 2.63 7.19 5.06 81.0 223.8 106.4 3.19 8.81 4.19 81.0 223.8 115.9 3.19 8.81 4.57 81.0 223.8 131.8 3.19 8.81 5.19 81.0 223.8 106.4 3.19 8.81 4.19 81.0 223.8 112.7 3.19 8.81 4.44 81.0 223.8 131.8 3.19 8.81 5.19 94.5 250.8 92.1 3.72 9.87 3.63 94.5 250.8 92.1 3.72 9.87 3.63 94.5 250.8 106.4 3.72 9.87 4.19 94.5 250.8 112.7 3.72 9.87 4.44 94.5 250.8 115.9 3.72 9.87 4.56 94.5 250.8 131.8 3.72 9.87 5.19 94.5 250.8 158.8 3.72 9.87 6.25 94.5 250.8 92.1 3.72 9.87 3.63 94.5 250.8 92.1 3.72 9.87 3.63 94.5 250.8 106.4 3.72 9.87 4.19 94.5 250.8 112.7 3.72 9.87 4.44 94.5 250.8 115.9 3.72 9.87 4.56 94.5 250.8 131.8 3.72 9.87 5.19 94.5 250.8 158.8 3.72 9.87 6.25

Bolt Size mm / in M12 x 75 ½ x 3 M12 x 75 ½ x 3 M12 x 75 ½ x 3 M12 x 75 ½ x 3 M16 x 90 ⅝ x 3½ M16 x 90 ⅝ x 3½ M16 x 90 ⅝ x 3½ M16 x 90 ⅝ x 3½ M16 x 90 ⅝ x 3½ M16 x 90 ⅝ x 3½ M16 x 90 ⅝ x 3½ M16 x 90 ⅝ x 3½ M16 x 90 ⅝ x 3½ M16 x 90 ⅝ x 3½ M16 x 90 ⅝ x 3½ M16 x 90 5/8 x 3-1/2 M16 x 90 ⅝ x 3½ M16 x 90 ⅝ x 3½ M16 x 90 ⅝ x 3½ M16 x 90 ⅝ x 3½ M16 x 90 ⅝ x 3½ M16 x 90 ⅝ x 3½ M16 x 90 ⅝ x 3½ M16 x 90 ⅝ x 3½

Weight Kgs / Lbs 2.27 5.00 2.47 5.43 2.57 5.65 2.91 6.41 2.90 6.38 3.40 7.40 3.82 8.41 2.90 6.38 3.39 7.46 3.82 8.40 2.53 5.57 3.00 6.60 3.17 6.97 3.58 7.88 3.75 8.25 4.13 9.09 4.77 10.50 2.91 6.41 2.99 6.58 3.18 7.00 3.58 7.88 3.58 7.88 4.10 9.02 4.76 10.47

Pipe O. D. mm / in 219.1 x 60.3 8.625 x 2.375 219.1 x 73.0 8.625 x 2.875 219.1 x 76.1 8.625 x 3.000 219.1 x 114.3 8.625 x 4.500

Hole Dia. +3.2, -0 / +0.13, -0 mm / in [70] [2.75] 70 2.75 89 3.50 114 4.50

T* A mm / in mm / in 135 166 5.31 6.54 137 166 5.39 6.54 136 166 5.35 6.54 133 166 5.24 6.54

Dimensions B C D mm / in mm / in mm / in 120 327 101 4.72 12.87 3.98 120 327 104 4.72 12.87 4.09 120 327 128 4.72 12.87 5.04 120 327 164 4.72 12.87 6.46

Bolt Size mm / in M20 x 120 ¾ x 4¾ M20 x 120 ¾ x 4¾ M20 x 120 ¾ x 4¾ M20 x 120 ¾ x 4¾

Weight Kgs / Lbs 6.2 13.6 6.2 13.7 7.1 15.6 8.0 17.6

MODEL 7721

Nominal Size Run x Branch mm / in 200 x 50 8 x 2 200 x 65 8 x 2.5 200 x 80 8 x 3 200 x 100 8 x 4

1. Hole diameters listed are suggested hole saw diameters. 2. *T: Take-out (Center of run to end of pipe to be engaged) 3. Special caution is required to some exceptional hole sizes shown in [ ].


www.shurt.com


Catalog 2011

MODEL

M22 MECHANICAL TEE

GROOVED-END OUTLET

The groove dimensions conform to AWWA C606. UL/FM working pressure is 20 bar (300 psi). The Model 7722 is available in

C

8" sizes. A




300 psi @100°F 20 Bar @38°C


Class 150

D

B


Nominal Size Run x Branch mm / in 50 x 25 2 x 1 50 x 32 2 x 1¼ 50 x 40 2 x 1½ 65 x 25 2½ x 1 65 x 32 2½ x 1¼ 65 x 40 2½ x 1½ 76.1 x 25 76.1 x 32 76.1 x 40 80 x 25 3 x 1 80 x 32 3 x 1¼ 80 x 40 3 x 1½ 80 x 50 3 x 2 100 x 25 4 x 1 100 x 32 4 x 1¼ 100 x 40 4 x 1½ 100 x 50 4 x 2 100 x 65 4 x 2½ 100 x 76.1 100 x 80 4 x 3 139.7 x 50 139.7 x 76.1 139.7 x 80 125 x 50 5 x 2 125 x 65 5 x 2½ 125 x 76.1 125 x 80 5 x 3

Pipe O. D. mm / in 60.3 x 33.4 2.375 x 1.315 60.3 x 42.2 2.375 x 1.660 60.3 x 48.3 2.375 x 1.900 73.0 x 33.4 2.875 x 1.315 73.0 x 42.2 2.875 x 1.660 73.0 x 48.3 2.875 x 1.900 76.1 x 33.4 3.000 x 1.315 76.1 x 42.2 3.000 x 1.660 76.1 x 48.3 3.000 x 1.900 88.9 x 33.4 3.500 x 1.315 88.9 x 42.2 3.500 x 1.660 88.9 x 48.3 3.500 x 1.900 88.9 x 60.3 3.500 x 2.375 114.3 x 33.4 4.500 x 1.315 114.3 x 42.2 4.500 x 1,660 114.3 x 48.3 4.500 x 1.900 114.3 x 60.3 4.500 x 2.375 114.3 x 73.0 4.500 x 2.875 114.3 x 76.1 4.500 x 3.000 114.3 x 88.9 4.500 x 3.500 139.7 x 60.3 5.500 x 2.375 139.7 x 76.1 5.500 x 3.000 139.7 x 88.9 5.500 x 3.500 141.3 x 60.3 5.563 x2.375 141.3 x 73.0 5.563x 2.875 141.3 x 76.1 5.563x 3.000 141.3 x 88.9 5.563 x 3.500

Hole Dia. +3.2, -0 / +0.13, -0 mm / in 38 1.50 [45] [1.75] [45] [1.75] 38 1.50 51 2.00 51 2.00 38 1.50 51 2.00 51 2.00 38 1.50 51 2.00 51 2.00 64 2.50 38 1.50 51 2.00 51 2.00 64 2.50 70 2.75 70 2.75 89 3.50 64 2.50 70 2.75 70 2.75 64 2.50 70 2.75 70 2.75 70 2.75

A mm / in 73.0 2.87 76.2 3.00 76.2 3.00 79.4 3.13 82.6 3.25 82.6 3.25 79.4 3.13 82.6 3.25 82.6 3.25 85.7 3.37 90.5 3.56 90.5 3.56 90.5 3.56 93.7 3.69 92.1 3.63 92.1 3.63 101.6 4.00 101.6 4.00 101.6 4.00 104.8 4.13 120.7 4.75 120.7 4.75 117.5 4.63 120.7 4.75 120.7 4.75 120.7 4.75 117.5 4.63

B mm / in 38.1 1.50 38.1 1.50 38.1 1.50 44.5 1.75 44.5 1.75 44.5 1.75 46.1 1.81 46.1 1.81 46.1 1.81 53.2 2.09 53.2 2.09 53.2 2.09 53.2 2.09 66.7 2.63 66.7 2.63 66.7 2.63 66.7 2.63 66.7 2.63 66.7 2.63 66.7 2.63 81.0 3.19 81.0 3.19 81.0 3.19 81.0 3.19 81.0 3.19 81.0 3.19 81.0 3.19

Dimensions C D mm / in mm / in 115.9 81.0 4.57 3.19 115.9 84.0 4.57 3.31 115.9 84.0 4.57 3.31 141.3 81.0 5.56 3.19 141.3 94.0 5.56 3.70 141.3 94.0 5.56 3.70 144.5 81.0 5.69 3.19 144.5 94.0 5.69 3.70 144.5 94.0 5.69 3.70 157.2 81.0 6.19 3.19 157.2 94.0 6.19 3.70 157.2 94.0 6.19 3.70 157.2 108.0 6.19 4.25 182.6 79.4 7.19 3.13 182.6 101.6 7.19 4.00 182.6 101.6 7.19 4.00 182.6 101.6 7.19 4.00 182.6 112.7 7.19 4.44 182.6 112.7 7.19 4.44 182.6 128.6 7.19 5.06 223.8 106.4 8.81 4.19 223.8 112.7 8.81 4.44 223.8 131.8 8.81 5.19 223.8 106.4 8.81 4.19 223.8 112.7 8.81 4.44 223.8 112.7 8.81 4.44 223.8 131.8 8.81 5.19

Bolt Size mm / in M10 x 55 ⅜ x 2⅛ M10 x 55 ⅜ x 2⅛ M10 x 55 ⅜ x 2⅛ M12 x 60 ⅜ x 2⅜ M12 x 60 ⅜ x 2⅜ M12 x 60 ⅜ x 2⅜ M12 x 60 ½ x 2⅜ M12 x 60 ½ x 2⅜ M12 x 60 ½ x 2⅜ M12 x 75 ½ x 3 M12 x 75 ½ x 3 M12 x 75 ½ x 3 M12 x 75 ½ x 3 M12 x 75 ½ x 3 M12 x 75 ½ x 3 M12 x 75 ½ x 3 M12 x 75 ½ x 3 M12 x 75 ½ x 3 M12 x 75 ½ x 3 M12 x 75 ½ x 3 M16 x 90 ⅝ x 3½ M16 x 90 ⅝ x 3½ M16 x 90 ⅝ x 3½ M16 x 90 ⅝ x 3½ M16 x 90 ⅝ x 3½ M16 x 90 ⅝ x 3½ M16 x 90 ⅝ x 3½

1. Hole diameters listed are suggested hole saw diameters. 2. Special caution is required to some exceptional hole sizes shown in [ ].



www.shurt.com

Weight Kgs / Lbs 1.03 2.27 1.11 2.44 1.18 2.60 1.23 2.71 1.39 3.06 1.42 3.12 1.23 2.71 1.39 3.06 1.42 3.12 1.45 3.19 1.68 3.70 1.70 3.74 1.83 4.03 1.65 3.63 1.80 3.96 1.81 3.98 1.93 4.25 2.66 5.85 2.17 4.78 2.41 5.30 2.63 5.79 2.95 6.50 3.08 6.78 2.63 5.79 2.88 6.34 2.95 6.49 3.08 6.78

Continued on next page

Catalog 2011

MODEL

M22 & 7722 MECHANICAL TEE

GROOVED-END OUTLET

The groove dimensions conform to AWWA C606. UL/FM working pressure is 20 bar (300 psi). The Model 7722 is available in 8" sizes. C

D

A B

Continued from previous page (Model M22)

Nominal Size Run x Branch mm / in 165.1 x 32 165.1 x 40 165.1 x 50 165.1 x 76.1 165.1 x 80 165.1 x 100 150 x 32 6 x 1¼ 150 x 40 6 x 1½ 150 x 50 6 x 2 150 x 65 6 x 2½ 150 x 80 6 x 3 150 x 100 6 x 4

Pipe O. D. mm / in 165.1 x 42.2 6.500 x 1.660 165.1 x 48.3 6.500 x 1.900 165.1 x 60.3 6.500 x 2.375 165.1 x 76.1 6.500 x 3.000 165.1 x 88.9 6.500 x 3.500 165.1 x 114.3 6.500 x 4.500 168.3 x 42.2 6.625 x 1.660 168.3 x 48.3 6.625 x 1.900 168.3 x 60.3 6.625 x 2.375 168.3 x 73.0 6.625 x 2.875 168.3 x 88.9 6.625 x 3.500 168.3 x 114.3 6.625 x 4.500

Hole Dia. +3.2, -0 / +0.13, -0 mm / in 51 2.00 51 2.00 64 2.50 70 2.75 89 3.50 114 4.50 51 2.00 51 2.00 64 2.50 70 2.75 89 3.50 114 4.50

A mm / in 130.2 5.13 130.2 5.13 130.2 5.13 130.2 5.13 130.2 5.13 137.1 5.40 130.2 5.13 130.2 5.13 130.2 5.13 130.2 5.13 130.2 5.13 137.1 5.40

B mm / in 94.5 3.72 94.5 3.72 94.5 3.72 94.5 3.72 94.5 3.72 94.5 3.72 94.5 3.72 94.5 3.72 94.5 3.72 94.5 3.72 94.5 3.72 94.5 3.72

Dimensions C D mm / in mm / in 250.8 92.1 9.87 3.63 250.8 92.1 9.87 3.63 250.8 106.4 9.87 4.19 250.8 115.9 9.87 4.56 250.8 131.8 9.87 5.19 250.8 158.8 9.87 6.25 250.8 92.1 9.87 3.63 250.8 92.1 9.87 3.63 250.8 106.4 9.87 4.19 250.8 112.7 9.87 4.44 250.8 131.8 9.87 5.19 250.8 158.8 9.87 6.25

Bolt Size mm / in M16 x 90 ⅝ x 3½ M16 x 90 ⅝ x 3½ M16 x 90 ⅝ x 3½ M16 x 90 ⅝ x 3½ M16 x 90 ⅝ x 3½ M16 x 90 ⅝ x 3½ M16 x 90 5/8 x 3½ M16 x 90 ⅝ x 3½ M16 x 90 ⅝ x 3½ M16 x 90 ⅝ x 3½ M16 x 90 ⅝ x 3½ M16 x 90 ⅝ x 3½

Weight Kgs / Lbs 2.74 6.03 2.78 6.12 2.91 6.40 3.38 7.44 3.64 8.01 4.05 8.91 2.75 6.05 2.78 6.12 2.92 6.42 3.22 7.08 3.68 8.10 4.05 8.91

Pipe O. D. mm / in 219.1 x 60.3 8.625 x 2.375 219.1 x 73.0 8.625 x 2.875 219.1 x 76.1 8.625 x 3.000 219.1 x 88.9 8.625 x 3.500 219.1 x 114.3 8.625 x 4.500

Hole Dia. +3.2, -0 / +0.13, -0 mm / in [70] [2.75] 70 2.75 70 2.75 89 3.50 114 4.50

A mm / in 166 6.54 166 6.54 166 6.54 166 6.54 166 6.54

B mm / in 120 4.72 120 4.72 120 4.72 120 4.72 120 4.72

Dimensions C D mm / in mm / in 327 104 12.87 3.89 327 104 12.87 4.09 327 104 12.87 4.09 327 128 12.87 5.04 327 164 12.87 6.46

Bolt Size mm / in M20 x 120 ¾ x 4¾ M20 x 120 ¾ x 4¾ M20 x 120 ¾ x 4¾ M20 x 120 ¾ x 4¾ M20 x 120 ¾ x 4¾

Weight Kgs / Lbs 5.8 12.8 6.0 13.2 6.0 13.2 7.2 15.8 7.5 16.5

MODEL 7722

Nominal Size Run x Branch mm / in 200 x 50 8 x 2 200 x 65 8 x 2½ 200 x 76.1 200 x 80 8 x 3 200 x 100 8 x 4

1. Hole diameters listed are suggested hole saw diameters. 2. Special caution is required to some exceptional hole sizes shown in [ ].


www.shurt.com


Catalog 2011

MODEL

723 SADDLE-LET Small Mechanical Tee

The Model 723 Saddle-Let is the ideal outlet fitting for making direct connections to sprinkler heads, drop nipples and or gauges. No need for welding, just cut or drill a hole at

C

the desired outlet location.

A




300 psi @100°F 20 Bar @38°C


Class 150

B

T


Nominal Size mm / in 32 x 15 1¼ x ½ 32 x 20 1¼ x ¾ 32 x 25 1¼ x 1 40 x 15 1½ x ½ 40 x 20 1½ x ¾ 40 x 25 1½ x 1 50 x 15 2 x ½ 50 x 20 2 x ¾ 50 x 25 2 x 1 65 x 15 2½ x ½ 65 x 20 2½ x ¾ 65 x 25 2½ x 1

Hole Dia. +1.6, -0 / +0.063, -0 A mm / in mm / in 30 53.0 1.18 2.08 30 53.0 1.18 2.08 30 56.0 1.18 2.20 30 55.0 1.18 2.16 30 55.0 1.18 2.16 30 58.0 1.18 2.28 30 64.0 1.18 2.51 30 64.0 1.18 2.51 30 67.0 1.18 2.63 30 69.0 1.18 2.71 30 69.0 1.18 2.71 30 72.0 1.18 2.83

Dimensions B C mm / in mm / in 89.0 56.0 3.50 2.20 89.0 56.0 3.50 2.20 89.0 56.0 3.50 2.20 89.0 56.0 3.50 2.20 89.0 56.0 3.50 2.20 89.0 56.0 3.50 2.20 98.0 56.0 3.85 2.20 98.0 56.0 3.85 2.20 98.0 56.0 3.85 2.20 111.0 56.0 4.37 2.20 111.0 56.0 4.37 2.20 111.0 56.0 4.37 2.20

Take-Out, T mm / in 35.0 1.38 35.0 1.38 38.0 1.50 35.0 1.38 35.0 1.38 38.0 1.50 42.0 1.65 42.0 1.65 45.0 1.77 51.0 2.00 51.0 2.00 54.0 2.13

Bolt Size in 3/8Ø U-Bolt 3/8Ø U-Bolt 3/8Ø U-Bolt 3/8Ø U-Bolt 3/8Ø U-Bolt 3/8Ø U-Bolt 3/8Ø U-Bolt 3/8Ø U-Bolt 3/8Ø U-Bolt 3/8Ø U-Bolt 3/8Ø U-Bolt 3/8Ø U-Bolt

Bolt Torque N-m / Lb-Ft 20-30 15-22 20-30 15-22 20-30 15-22 20-30 15-22 20-30 15-22 20-30 15-22 20-30 15-22 20-30 15-22 20-30 15-22 20-30 15-22 20-30 15-22 20-30 15-22

1. Hole diameters listed are suggested hole saw diameters. 2. *T: Take-out (Center of run to end of pipe to be engaged)

Hole Cutting

The method of pipe preparation requires the cutting or drilling of a specified hole size on the centerline of the pipe. Always use the correct hole saw size as shown in the table and never use a torch for cutting a hole.

Hole Sizes for 723 Saddle-let Saddle- Let Branch Size 15, 20, 25 ½, ¾, 1

Hole Dimensions Hole Saw Max dia. Size Allowed 30 32 113/16 1¼

unit: mm/in Surface Preparation “A” 89 3½

After the hole has been cut all rough edges must be removed and the area within 5/8” (16mm) of the hole should be inspected to ensure a clean smooth surface, free of any indentations or projections that could affect proper gasket sealing.



16mm ( ⅝" )

www.shurt.com

Weight Kgs / Lbs 0.4 0.9 0.4 0.9 0.4 0.9 0.4 0.9 0.4 0.9 0.4 0.9 0.4 0.9 0.4 0.9 0.4 0.9 0.4 0.9 0.4 0.9 0.5 1.1

Catalog 2011

Performance Data Sheet - Ductile Iron Couplings on Carbon Steel & Stainless Steel Pipe The following tables show maximum working pressures (CWP) of Shurt ductile iron couplings and flange adapters used on

both carbon steel and stainless steel pipes. Shurt ductile iron

couplings can be used in conjunction with stainless steel pipe in non-corrosive environment as the flow media does not come in direct with the coupling housings but rather only the gasket.

unit: psi

Size in 1¼ 1½ 2 2½ 3 4 5 6 8

Model Z05 on Carbon Steel Pipe Cut-Grooved Roll-Grooved XS STD STD Sch. 10 600 600 500 400 600 600 500 400 600 600 500 400 600 600 500 400 600 600 500 400 600 600 500 400 450 450 350 300 450 450 350 300 450 450 350 300

Size in 1¼ 1½ 2 2½ 3 4 5 6 8 10 12

Model Z07 on Carbon Steel Pipe Cut-Grooved Roll-Grooved XS STD STD Sch. 10 750 750 750 600 750 750 750 600 750 750 750 600 750 750 750 600 750 750 750 600 750 750 750 600 750 750 750 500 700 700 700 400 600 600 600 350 500 500 500 300 400 400 400 250

Size in 2 2½ 3 4 6 8 10 12

Model XH-1000 on Carbon Steel Pipe Cut-Grooved Roll-Grooved XS STD STD Sch. 10 1500 1000 1000 750 1500 1000 1000 600 1500 1000 1000 600 1500 1000 1000 600 1500 1000 1000 450 900 800 800 300 900 800 800 300 900 800 800 200

Size in 1 1¼ 1½ 2 2½ 3 4 5 6 8 10 12

Model 7705 on Carbon Steel Pipe Cut-Grooved Roll-Grooved XS STD STD Sch. 10 600 600 500 400 600 600 500 400 600 600 500 400 600 600 500 400 600 600 500 400 600 600 500 400 600 600 500 400 450 450 450 350 450 450 450 350 450 450 300 250 350 350 300 200 350 350 300 200

Size in ¾ 1 1¼ 1½ 2 2½ 3 4 5 6 8 10 12

Model 7707 on Carbon Steel Pipe Cut-Grooved Roll-Grooved XS STD STD Sch. 10 1000 1000 750 600 1000 1000 750 600 1000 1000 750 600 1000 1000 750 600 1000 1000 750 600 1000 1000 750 600 1000 1000 750 600 1000 1000 750 600 1000 1000 750 500 1000 1000 700 450 800 800 600 350 800 800 550 300 800 800 500 300


unit: psi

Sch. 7 250 250 250 250 250 200 175 175 150

Size in 1¼ 1½ 2 2½ 3 4 5 6 8

Model Z05 on Stainless Steel Pipe Cut-Grooved Roll-Grooved Sch. 80S Sch. 40S Sch. 40S Sch. 10S 600 600 450 300 600 600 450 300 600 600 450 300 600 600 450 300 600 600 450 300 600 600 450 300 450 450 300 200 450 450 300 125 450 450 300 100

Sch. 5S 250 250 250 250 250 200 NR NR NR

Sch. 7 400 400 400 400 400 400 350 300 250 200 150

Size in 1¼ 1½ 2 2½ 3 4 5 6 8 10 12

Model Z07 on Stainless Steel Pipe Cut-Grooved Roll-Grooved Sch. 80S Sch. 40S Sch. 40S Sch. 10S 750 750 700 500 750 750 700 500 750 750 700 500 750 750 700 500 750 750 700 500 750 750 700 400 750 750 600 300 700 700 500 200 600 600 400 150 500 500 300 100 400 400 250 100

Sch. 5S 300 300 300 300 300 250 NR NR NR NR NR

Sch. 7 NR NR NR NR NR NR NR NR

Size in 2 2½ 3 4 6 8 10 12

Model XH-1000 on Stainless Steel Pipe Cut-Grooved Roll-Grooved Sch. 80S Sch. 40S Sch. 40S Sch. 10S 1500 1000 750 500 1500 1000 750 500 1500 1000 750 500 1500 1000 750 400 1500 1000 500 200 900 800 400 125 900 800 400 125 900 800 400 125

Sch. 5S NR NR NR NR NR NR NR NR

Sch. 7 300 300 300 300 300 300 300 250 250 200 175 175

Size in 1 1¼ 1½ 2 2½ 3 4 5 6 8 10 12

Model 7705 on Stainless Steel Pipe Cut-Grooved Roll-Grooved Sch. 80S Sch. 40S Sch. 40S Sch. 10S 600 600 450 300 600 600 450 300 600 600 450 300 600 600 450 300 600 600 450 300 600 600 450 300 600 600 450 300 450 450 300 200 450 450 300 125 450 450 300 100 350 350 200 NR 350 350 200 NR

Sch. 5S 250 250 250 250 250 250 200 NR NR NR NR NR

Sch. 7 500 500 500 500 500 500 500 400 350 300 250 200 200

Size in ¾ 1 1¼ 1½ 2 2½ 3 4 5 6 8 10 12

Model 7707 on Stainless Steel Pipe Cut-Grooved Roll-Grooved Sch. 80S Sch. 40S Sch. 40S Sch. 10S 750 750 700 450 750 750 700 450 750 750 700 450 750 750 700 450 750 750 700 450 750 750 700 450 750 750 700 450 750 750 700 400 750 750 600 300 750 750 500 200 600 600 450 150 600 600 400 125 600 600 400 125

Sch. 5S 325 325 325 325 325 325 325 250 NR NR NR NR NR

www.shurt.com


Catalog 2011

unit: psi

Size in 2 2½ 3 4 5 6

Model M-7 on Carbon Steel Pipe Cut-Grooved Roll-Grooved XS STD STD Sch. 10 500 500 500 350 500 500 500 350 500 500 500 350 500 500 500 350 400 400 400 350 400 400 400 350

Size in 1½ x 1¼ 2 x '1½ 2½ x 2 3 x 2 3 x '2½ 4 x 2 4 x '2½ 4 x 3 5 x 4 6 x 3 6 x 4 8 x 6

Model 7706 on Carbon Steel Pipe Cut-Grooved Roll-Grooved XS STD STD Sch. 10 500 500 500 350 500 500 500 350 500 500 500 350 500 500 500 350 500 500 500 350 500 500 500 350 500 500 500 350 500 500 500 300 400 400 400 300 400 400 400 300 400 400 400 300 400 400 400 300

Size in 1½ 2 2½ 3 4 5 6 8 10 12

Model G28 on Carbon Steel Pipe Cut-Grooved Roll-Grooved XS STD STD Sch. 10 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 250 300 300 300 250 300 300 300 250

Size in 1½ x * 2 x * 2½ x * 3 x * 4 x * 6 x *

Model C-7 on Carbon Steel Pipe Cut-Grooved Roll-Grooved XS STD STD Sch. 10 500 500 500 350 500 500 500 350 500 500 500 350 500 500 500 350 500 500 500 350 400 400 400 350

unit: psi

Sch. 7 300 300 300 300 250 250

Size in 2 2½ 3 4 5 6

Model M-7 on Stainless Steel Pipe Cut-Grooved Roll-Grooved Sch. 80S Sch. 40S Sch. 40S Sch. 10S 500 500 450 300 500 500 450 300 500 500 450 300 500 500 450 300 400 400 300 200 400 400 300 125

Sch. 5S 250 250 250 200 NR NR

Sch. 7 300 300 300 300 300 300 300 250 250 200 175 175

Size in 1½ x 1¼ 2 x '1½ 2½ x 2 3 x 2 3 x '2½ 4 x 2 4 x '2½ 4 x 3 5 x 4 6 x 3 6 x 4 8 x 6

Model 7706 on Stainless Steel Pipe Cut-Grooved Roll-Grooved Sch. 80S Sch. 40S Sch. 40S Sch. 10S 500 500 350 300 500 500 350 300 500 500 350 300 500 500 350 300 500 500 350 300 500 500 350 300 500 500 350 300 500 500 300 250 400 400 300 250 400 400 300 200 400 400 300 175 400 400 300 175

Sch. 5S 250 250 250 250 250 250 200 200 NR NR NR NR

Sch. 7 NR NR NR NR NR NR NR NR NR NR

Size in '1½ 2 2.5 3 4 5 6 8 10 12

Model G28 on Stainless Steel Pipe Cut-Grooved Roll-Grooved Sch. 80S Sch. 40S Sch. 40S Sch. 10S 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 175 300 300 250 150 300 300 250 150 300 300 200 NR 300 300 200 NR 300 300 200 NR

Sch. 5S NR NR NR NR NR NR NR NR NR NR

Sch. 7 300 300 300 300 300 300

Size in 1½ x * 2 x * 2½ x * 3 x * 4 x * 6 x *

Model C-7 on Stainless Steel Pipe Cut-Grooved Roll-Grooved Sch. 80S Sch. 40S Sch. 40S Sch. 10S 500 500 350 300 500 500 350 300 500 500 350 300 500 500 350 300 500 500 350 300 400 400 300 300

Sch. 5S 250 250 250 250 250 250

* = all branch sizes, threaded and grooved

* = all branch sizes, threaded and grooved

Sch. 7 NR NR NR NR NR NR NR NR NR NR NR NR NR NR

Size in 2 2½ 3 4 5 6 8 10 12 14 16 18 20 24

Model 7041 on Stainless Steel Pipe Cut-Grooved Roll-Grooved Sch. 80S Sch. 40S Sch. 40S Sch. 10S 300 300 275 275 300 300 275 275 300 300 275 275 300 300 275 275 300 300 275 200 300 300 250 200 300 300 200 NR 300 300 200 NR 300 300 200 NR 250 250 125 NR 250 250 125 NR 250 250 125 NR 250 250 100 NR 250 250 100 NR

Sch. 5S 175 175 175 175 175 125 NR NR NR NR NR NR NR NR

Sch. 7 NR NR NR NR NR NR NR NR NR

Size in 2 2½ 3 4 5 6 8 10 12

Model 7043 on Stainless Steel Pipe Cut-Grooved Roll-Grooved Sch. 80S Sch. 40S Sch. 40S Sch. 10S 400 400 400 NR 400 400 400 NR 400 400 400 NR 300 300 300 NR 300 300 250 NR 300 300 200 NR 250 250 150 NR 250 250 150 NR 250 250 150 NR

Sch. 5S NR NR NR NR NR NR NR NR NR

Size in 2 2½ 3 4 5 6 8 10 12 14 16 18 20 24

Model 7041 on Carbon Steel Pipe Cut-Grooved Roll-Grooved XS STD STD Sch. 10 300 300 300 250 300 300 300 250 300 300 300 250 300 300 300 250 300 300 300 250 300 300 300 250 300 300 300 200 300 300 300 200 300 300 300 200 300 300 300 200 300 300 300 175 300 300 300 175 300 300 300 150 300 300 300 150

Hydrostatic shell test: 450 psi (30 Bar) per ANSI B16.5

Size in 2 2½ 3 4 5 6 8 10 12

Model 7043 on Carbon Steel Pipe Cut-Grooved Roll-Grooved XS STD STD Sch. 10 750 750 750 500 750 750 750 500 750 750 750 500 750 750 750 500 750 750 750 450 750 750 750 450 750 750 750 300 750 750 750 300 750 750 750 250

Hydrostatic shell test: 1125 psi (77 Bar) per ANSI B16.5



www.shurt.com

Section 2 Cast & Wrought Grooved Fittings Shurt Grooved Fittings. ........................................................... 42 Flow Data / Friction Resistance. .................................................. 42 Ductile Iron Grooved Fittings 7110 / 7111 / 7112 / 7113 Elbows................................................... 43 7120 / 7135 / 7130 Tee, Cross, Lateral........................................... 44 7121 Reducing Tee............................................................................. 45 7150 / 7151 Concentric & Eccentric Reducers................................. 46 7160 / 7160T / 7160H / 7160P Caps............................................ 47 7110LR / 7111LR / 7137 / 7112G / 7110-B Elbows & True-Y... 48 901 / 903 / 7110DR / 7127 Elbows & Tee..................................... 49 7125 / 7150F / 7150M Bullhead Tee & Reducers.......................... 50 899 / 55 / 56 End-All & Nipples......................................................... 51 850 / 851 / 853 Sprinkler Hubs........................................................ 52 7114 / 7122 / 7133 Hydrant Elbow & Tees..................................... 53 Wrought Grooved Fittings W110 / W110LR / W111LR / W120 / W160 / W121 Elbows & Tee...54 W150 / W151 / 57 / 58 / 59 Concentric & Eccentric Reducers, Nipples... 55 L90-3D / L60-3D / L45-3D / L30-3D / L22-3D / L11-3D Elbows..... 56 L90-5D / L60-5D / L45-5D / L30-5D / L22-5D / L11-5D Elbows..... 57 L90-6D / L60-6D / L45-6D / L30-6D / L22-6D / L11-6D Elbows..... 57 Extra Heavy Grooved Fittings 10EP / 11EP / 20EP / 35EP / 22EP Elbows, Tees & Cross....... 58


Catalog 2011

www.shurt.com

Catalog 2011

Shurt Grooved Fittings Shurt offers a wide range of grooved-end fittings in sizes through 24” (600mm). Fittings are available in a number of styles and configurations to a variety of applications. Shurt grooved-end fittings are manufactured and designed to meet ASTM F1548 and ANSI/AWWA C606 requirements for use with grooved mechanical couplings conforming to ASTM F1476. For sizes not specified in these standards, please refer to applicable groove specifications shown in this catalog. Pressure-Temperature Rating Size

Nom. Rating

1” – 6” Class 300 (25 – 150) 8” – 12” Class 250 (200 – 300) 14” – 24” Class 150 (250 – 600)

welded steel of the same or equivalent

Working Pressure Max. Service (STD, Roll-grooved) Temperature 750 psi @100°F 52 Bar @38°C 400 psi @100°F 28 Bar @38°C 300 psi @100°F 20 Bar @38°C


grade. Fittings are painted orange or red, or as an option can be supplied hot-dip galvanized or epoxy coated.


Rubber Lined Fittings

Shurt ductile iron grooved end fittings are also available with rubber lining for abrasive services. Shurt for further information.

For abrasive services

For abrasive and corrosive services

Most fittings are provided in ductile iron conforming to ASTM A536 Gr. 65-45-12 and or ASTM A395 Gr. 65-45-15. Some styles and sizes larger than 14” (350mm) are fabricated from carbon steel pipe to ASTM A53 Gr. B or fabricated of segmentally

Flow Data / Frictional Resistance

Expressed as equivalent length of straight pipe Nominal Pipe Pipe Wall #7110 90° #901 90° Size O.D. Thickness Std. Radius Short. Radius mm / in mm / in mm / in meters / feet meters / feet 25 33.4 3.4 0.5 --- 1 1.315 0.133 1.7 --- 32 42.2 3.6 0.8 0.8 1¼ 1.660 0.140 2.5 2.5 40 48.3 40 1.1 1.1 1½ 1.900 0.154 3.5 3.5 50 60.3 5.2 1.2 1.2 2 2.375 0.203 4.0 4.0 65 73.0 5.0 1.4 1.4 2½ 2.875 0.197 4.5 4.5 80 88.9 6.3 1.5 1.5 3 3.500 0.237 5.0 5.0 100 114.3 5.6 2.0 2.0 4 4.500 0.220 6.7 6.7 125 141.3 6.6 2.3 2.3 5 5.563 0.258 7.5 7.5 150 168.3 7.1 2.7 2.7 6 6.625 0.280 9.0 9.0 200 219.1 8.2 4.0 4.0 8 8.625 0.322 13.0 13.0 250 273.0 8.8 5.2 --- 10 10.750 0.365 17.0 --- 300 323.9 9.5 6.1 --- 12 12.750 0.375 20.0 ---

Elbows #7110LR 90° #7111 45° #7111LR 45° 1½ D. LR Std. Radius 1½ D. LR meters / feet meters / feet meters / feet --- 0.2 --- --- 0.8 --- --- 0.3 --- --- 1.0 --- --- 0.5 --- --- 1.5 --- 0.8 0.5 0.3 2.5 1.7 1.1 0.9 0.6 0.4 2.9 2.0 1.4 1.2 0.8 0.5 3.8 2.5 1.5 1.5 0.9 0.6 5.0 3.0 2.1 1.8 1.2 0.6 6.0 4.0 2.5 2.3 1.4 0.9 7.5 4.5 3.0 3.0 2.0 1.2 9.8 6.5 4.0 3.7 2.5 1.5 12.0 8.3 5.0 4.4 3.1 1.8 14.5 10.0 6.0

Tees #7120 #903 Branch Branch meters / feet meters / feet 1.3 --4.2 --1.4 1.4 4.7 4.7 2.0 2.0 6.5 6.5 2.6 2.6 8.5 8.5 3.1 3.1 10.0 10.0 3.7 3.7 12.0 12.0 4.6 4.6 15.0 15.0 5.8 5.8 19.0 19.0 6.7 6.7 22.0 22.0 10.1 10.1 33.0 33.0 12.5 --41.0 --14.9 --49.0 ---

The values listed in this table express the frictional resistance of representative Shurt fittings as equivalent feet (meters) of straight pipe. For the branch of a tee that is reduced in size, use the value that corresponds to the branch size. For example, the branch value of a 4” x 4” x 3” tee is 12.8 feet (3.9 meters). For fittings not listed in this table, the equivalent length of straight pipe can be estimated from the data provided. For example, the flow resistance of a 22½° elbow is approximately one half that of a 45° elbow.



www.shurt.com

MODEL

Catalog 2011

MODEL

7110 90° elbow 7111 45° elbow 7112 22-½° elbow 7113 11-¼° elbow Shurt ductile iron grooved-end fittings are made of ductile iron per ASTM A536 Gr. 65-45-12 and or ASTM A395 Gr. 65-4515. C-E dimensions are manufacturer’s standard. See page 54 for wrought steel grooved-end fittings.

C-E

C-E

7110 90˚ Elbow

Nominal Size mm / in 25 1 32 1¼ 40 1½ 50 2 65 2½ 76.1mm 80 3 101.6mm 100 4 108.0mm 125 5 133.0mm 139.7mm 150 6 159.0mm 165.1mm 200 8 250 10 300 12 200JIS 250JIS 300JIS 350 14 400 16 450 18 500 20 600 24

Pipe O. D. mm / in 33.4 1.315 42.2 1.660 48.3 1.900 60.3 2.375 73.0 2.875 76.1 3.000 88.9 3.500 101.6 4.000 114.3 4.500 108.0 4.250 141.3 5.563 133.0 5.250 139.7 5.500 168.3 6.625 159.0 6.250 165.1 6.500 219.1 8.625 273.0 10.750 323.9 12.750 216.3 8.516 267.4 10.528 318.5 12.539 355.6 14.000 406.4 16.000 457.2 18.000 508.0 20.000 609.6 24.000

#7110 90˚ Elbow C - E Weight mm / in Kgs / Lbs 57 0.3 2.25 0.7 70 0.5 2.75 1.1 70 0.6 2.75 1.3 83 0.9 3.25 2.0 95 1.2 3.75 2.6 95 1.4 3.75 3.1 108 2.0 4.25 4.3 114 2.5 4.50 5.6 127 3.1 5.00 6.9 127 2.5 5.00 5.5 140 5.0 5.50 11.0 140 4.1 5.50 9.0 140 4.3 5.50 9.5 165 5.8 6.50 12.8 165 6.0 6.50 13.2 165 5.7 6.50 12.5 197 13.0 7.75 28.7 229 24.1 9.00 53.1 254 36.7 10.00 81.0 197 12.4 7.75 27.2 229 24.0 9.00 52.8 254 35.0 10.00 77.0 280 35.1 11.00 77.5 305 43.0 12.00 94.6 394 83.5 15.50 184.0 438 118.5 17.25 261.2 508 185.0 20.00 407.9


C-E 7111 45˚ Elbow

#7111 45˚ Elbow C - E Weight mm / in Kgs / Lbs 45 0.2 1.75 0.5 45 0.3 1.75 0.7 45 0.4 1.75 0.9 51 0.7 2.00 1.5 57 0.9 2.25 2.0 57 0.9 2.25 2.1 64 1.3 2.50 2.9 --- --- --- --- 76 2.0 3.00 4.4 76 2.0 3.00 4.4 83 3.0 3.25 6.6 83 2.7 3.25 5.9 83 2.9 3.25 6.4 89 4.0 3.50 8.9 89 3.8 3.50 8.4 89 4.0 3.50 8.9 108 8.6 4.25 19.0 121 15.5 4.75 34.2 133 22.5 5.25 49.5 108 8.4 4.25 18.5 121 15.5 4.75 34.2 133 22.5 5.25 49.5 152 22.0 6.00 48.4 184 44.0 7.25 96.8 203 46.6 8.00 102.5 229 54.5 9.00 120.2 280 83.5 11.00 184.1

7112 22½˚ Elbow #7112 22½˚ Elbow C - E Weight mm / in Kgs / Lbs --- --- --- --- --- --- --- --- 45 0.6 1.75 1.3 48 0.8 1.88 1.8 51 1.0 2.01 2.2 51 1.0 2.01 2.2 57 1.4 2.25 3.1 --- --- --- --- 73 2.0 2.88 4.4 --- --- --- --- 73 3.1 2.88 6.8 --- --- --- --- 73 2.9 2.88 6.5 79 5.0 3.12 11.0 --- --- --- --- 79 5.0 3.12 11.0 98 10.0 3.88 22.0 111 17.7 4.38 38.9 --- 19.5 --- 42.9 98 10.0 3.88 22.0 111 17.7 4.38 38.9 --- --- --- --- --- 21.0 --- 46.2 --- 22.0 --- 48.4 --- --- --- --- --- --- --- --- --- --- --- ---

www.shurt.com

C-E 7113 11¼˚ Elbow #7113 11¼˚ Elbow C - E Weight mm / in Kgs / Lbs --- ----- ----- ----- ----- ----- --35 0.4 1.38 1.0 38 0.7 1.50 1.6 38 0.8 1.50 1.7 38 0.8 1.50 1.8 --- ----- --45 1.0 1.75 2.2 --- ----- ----- ----- ----- ----- ----- ----- --51 2.5 2.00 5.5 --- ----- --51 2.5 2.00 5.5 51 5.5 2.00 12.1 54 10.0 2.13 22.1 57 12.4 2.25 27.3 --- ----- --54 10.0 2.13 22.1 57 12.4 2.25 27.3 --- ----- ----- ----- ----- ----- ----- ----- ----- ----- ---


Catalog 2011

MODEL

7120 tee 7135 cross 7130 45° lateral Shurt ductile iron grooved-end fittings are made of ductile iron per ASTM A536 Gr. 65-45-12 and or ASTM A395 Gr. 65-4515. C-E dimensions are manufacturer’s standard. See page 54 for wrought steel grooved-end fittings.

C

-L

E

C-LE

C-SE

C-E C-E

C-E 7135 Cross

7120 Tee Nominal Size mm / in 25 1 32 1¼ 40 1½ 50 2 65 2½ 76.1mm 80 3 100 4 108.0mm 125 5 133.0mm 139.7mm 150 6 150 6 165.1mm 200 8 250 10 300 12 200JIS 250JIS 300JIS 350 14 400 16


Pipe O. D. mm / in 33.4 1.315 42.2 1.660 48.3 1.900 60.3 2.375 73.0 2.875 76.1 3.000 88.9 3.500 114.3 4.500 108.0 4.250 141.3 5.563 133.0 5.250 139.7 5.500 168.3 6.625 159.0 6.250 165.1 6.500 219.1 8.625 273.0 10.750 323.9 12.750 216.3 8.516 267.4 10.528 318.5 12.539 355.6 14.000 406.4 16.000

C - E mm / in 57 2.25 70 2.75 70 2.75 83 3.25 95 3.75 95 3.75 108 4.25 127 5.00 127 5.00 140 5.50 140 5.50 140 5.50 165 6.50 165 6.50 165 6.50 197 7.75 229 9.00 254 10.00 197 7.75 229 9.00 254 10.00 280 11.00 305 12.00

#7120 Tee Weight Kgs / Lbs 0.4 0.9 0.7 1.5 0.9 2.0 1.3 2.9 2.2 4.8 2.3 5.1 3.1 6.8 4.5 9.9 4.1 9.0 6.5 14.3 6.0 13.2 6.5 14.3 10.0 22.0 8.6 18.9 9.4 20.8 20.0 44.0 31.0 68.2 43.9 96.7 20.0 44.0 31.0 68.2 43.9 96.7 52.0 114.6 68.0 149.9


C - E mm / in --- --- --- --- --- --- 83 3.25 95 3.75 95 3.75 108 4.25 127 5.00 --- --- 140 5.50 --- --- 140 5.50 165 6.50 --- --- 165 6.50 197 7.75 --- --- --- --- 197 7.75 --- --- --- --- --- --- --- ---

7130 45˚ Lateral

#7135 Cross Weight C - LE Kgs / Lbs mm / in --- --- --- --- --- --- --- --- --- --- --- --- 1.2 178 2.7 7.00 3.0 197 6.7 7.75 3.0 197 6.7 7.75 3.1 216 6.8 8.50 5.2 267 11.5 10.50 --- --- --- --- 5.9 318 13.0 12.50 --- --- --- --- 5.9 318 13.0 12.50 14.5 356 32.0 14.00 --- --- --- --- 14.5 356 32.0 14.00 20.0 457 44.1 18.00 --- 521 --- 20.50 --- 584 --- 23.00 20.0 457 44.1 18.00 --- 521 --- 20.50 --- 584 --- 23.00 --- --- --- --- --- --- --- ---

#7130 45˚ Lateral C - SE Weight mm / in Kgs / Lbs --- ----- ----- ----- ----- ----- --70 2.0 2.75 4.4 76 2.8 3.00 6.2 76 2.8 3.00 6.2 83 4.2 3.25 9.2 95 8.0 3.75 17.6 --- ----- --102 12.5 4.00 27.5 --- ----- --102 12.5 4.00 27.5 114 18.5 4.50 40.7 --- ----- --114 18.5 4.50 40.7 152 32.0 6.00 70.4 165 63.0 6.50 138.9 178 91.5 7.00 201.7 152 32.0 6.00 70.4 165 63.0 6.50 138.9 178 91.5 7.00 201.7 --- ----- ----- ----- ---

www.shurt.com

Catalog 2011

MODEL

7121 reducing tee Shurt ductile iron grooved-end fittings are made of ductile iron per ASTM A536 Gr. 65-45-12 and or ASTM A395 Gr. 65-4515. C-E dimensions are manufacturer’s standard. See page 54 for wrought steel

C-E 7121 Reducing Tee Nominal Size mm / in 50 x 50 x 40 2 x 2 x1½ 65 x 65 x 25 2½ x 2½ x 1 65 x 65 x 40 2½ x 2½ x 1½ 65 x 65 x 50 2½ x2½ x 2 65 x 65 x 50 2½ x 2½ x 2 80 x 80 x 25 3 x 3 x 1 80 x 80 x 40 3 x 3 x 1½ 80 x 80 x 50 3 x 3 x 2 80 x 80 x 65 3 x 3 x 2½ 80 x 80 x 65 3 x 3 x 2½ 100 x 100 x 25 4 x 4 x 1 100 x 100 x 50 4 x 4 x 2 100 x 100 x 65 4 x 4 x 2½ 100 x 100 x 76.1mm 100 x 100 x 80 4 x 4 x 3 125 x 125 x 50 5 x 5 x 2 125 x 125 x 100 5 x 5 x 4 150 x 150 x 50 6 x 6 x 2 150 x 150 x 65 6 x 6 x 2½

Pipe O. D. mm / in 60.3 x 60.3 x 48.3 2.375 x 2.375 x 1.900 73.0 x 73.0 x 33.4 2.875 x 2.875 x 1.315 76.1 x 76.1 x 48.3 3.000 x 3.000 x 1.900 73.0 x 73.0 x 60.3 2.875 x 2.875 x 2.375 76.1 x 76.1 x 60.3 3.000 x 3.000 x 2.375 88.9 x 88.9 x 33.4 3.500 x 3.500 x 1.315 88.9 x 88.9 x 48.3 3.500 x 3.500 x 1.900 88.9 x 88.9 x 60.3 3.500 x 3.500 x 2.375 88.9 x 88.9 x 73.0 3.500 x 3.500 x 2.875 88.9 x 88.9 x 76.1 3.500 x 3.500 x 3.000 114.3 x 114.3 x 33.4 4.500 x 4.500 x 1.315 114.3 x 114.3 x 60.3 4.500 x 4.500 x 2.375 114.3 x 114.3 x 73.0 4.500 x 4.500 x 2.875 114.3 x 114.3 x 76.1 4.500 x 4.500 x 3.000 114.3 x 114.3 x 88.9 4.500 x 4.500 x 3.500 141.3 x 141.3 x 60.3 5.563 x 5.563 x 2.375 141.3 x 141.3 x 114.3 5.563 x 5.563 x 4.500 168.3 x 168.3 x 60.3 6.625 x 6.625 x 2.375 168.3 x 168.3 x 73.0 6.625 x 6.625 x 2.875

Standard C - E mm / in 83 3.25 95 3.75 95 3.75 95 3.75 95 3.75 108 4.25 108 4.25 108 4.25 108 4.25 108 4.25 95 3.75 127 5.00 127 5.00 127 5.00 127 5.00 140 5.50 140 5.50 165 6.50 165 6.50

Threaded Br. C - E mm / in 83 3.25 95 3.75 95 3.75 95 3.75 95 3.75 108 4.25 108 4.25 108 4.25 108 4.25 108 4.25 95 3.75 127 5.00 127 5.00 127 5.00 127 5.00 140 5.50 140 5.50 165 6.50 165 6.50


Weight Kgs / Lbs 1.2 2.6 1.7 3.8 1.8 3.9 2.0 4.4 2.0 4.4 2.5 5.5 2.4 5.2 2.8 6.2 2.8 6.2 2.8 6.2 4.0 8.9 4.0 8.8 4.3 9.5 4.3 9.5 4.3 9.4 5.6 12.4 6.2 13.6 8.0 17.6 8.5 18.7

C-E

C-E

grooved-end fittings.

C-E 7121 Reducing Tee (Threaded)

Nominal Pipe Size O. D. mm / in mm / in 150 x 150 x 80 168.3 x 168.3 x 88.9 6 x 6 x 3 6.625 x 6.625 x 3.500 150 x 150 x 100 168.3 x 168.3 x 114.3 6 x 6 x 4 6.625 x 6.625 x 4.500 165.1 x 165.1 x 50 165.1 x 165.1 x 60.3 6 x 6 x 2 6.500 x 6.500 x 2.375 165.1 x 165.1 x 76.1 165.1 x165.1 x 76.1 6.500 x 6.500 x 3.000 165.1 x 165.1 x 80 165.1 x 165.1 x 88.9 6 x 6 x 3 6.500 x 6.500 x 3.500 165.1 x 165.1 x 100 165.1 x 165.1 x 114.3 6 x 6 x 4 6.500 x 6.500 x 4.500 200 x 200 x50 219.1 x 219.1 x 60.3 8 x 8 x 2 8.625 x 8.625 x 2.375 200 x 200 x 80 219.1 x 219.1 x 88.9 8 x 8 x 3 8.625 x 8.625 x 3.500 200 x 200 x 100 219.1 x 219.1 x 114.3 8 x 8 x 4 8.625 x 8.625 x 4.500 200 x 200 x 150 219.1 x 219.1 x 168.3 8 x 8 x 6 8.625 x 8.625 x 6.625 250 x 250 x 100 273.0 x 273.0 x 114.3 10 x 10 x 4 10.750 x 10.750 x 4.500 250 x 250 x 150 273.0 x 273.0 x 168.3 10 x 10 x 6 10.750 x 10.750 x 6.625 250 x 250 x 200 273.0 x 273.0 x 219.1 10 x 10 x 8 10.750 x 10.750 x 8.625 300 x 300 x 80 323.9 x 323.9 x 88.9 12 x 12 x 3 12.750 x 12.750 x 3.500 300 x 300 x 100 323.9 x 323.9 x114.3 12 x 12 x 4 12.750 x 12.750 x 4.500 300 x 300 x 150 323.9 x 323.9 x 168.3 12 x 12 x 6 12.750 x 12.750 x 6.625 300 x 300 x 200 323.9 x 323.9 x 219.1 12 x 12 x 8 12.750 x 12.750 x 8.625 300 x 300 x 250 323.9 x 323.9 x 273.0 12 x 12 x 10 12.750 x 12.750 x 10.750

Standard C - E mm / in 165 6.50 165 6.50 165 6.50 165 6.50 165 6.50 165 6.50 197 7.75 197 7.75 197 7.75 197 7.75 229 9.00 229 9.00 229 9.00 254 10.00 254 10.00 254 10.00 254 10.00 254 10.00

www.shurt.com

Threaded Br. C - E mm / in 165 6.50 165 6.50 165 6.50 165 6.50 165 6.50 165 6.50 197 7.75 197 7.75 197 7.75 --- --- 229 9.00 --- --- --- --- 254 10.00 254 10.00 --- --- --- --- --- ---

Weight Kgs / Lbs 9.2 20.2 8.8 19.4 8.0 17.6 8.5 18.7 9.2 20.2 8.8 19.4 14.8 32.5 15.5 34.2 20.0 44.0 21.0 46.2 28.5 62.8 30.0 66.0 31.5 69.3 40.0 88.1 41.0 90.4 38.0 83.6 38.0 83.6 40.0 88.0


Catalog 2011

MODEL

7150 CONCENTRIC REDUCER 7151 ECCENTRIC REDUCER Shurt ductile iron grooved-end fittings are made of ductile iron per ASTM A536 Gr. 65-45-12 and or ASTM A395 Gr. 65-4515. C-E dimensions are manufacturer’s standard. See page 55 for wrought steel grooved-end fittings.

E-E 7150 Conc. Reducer Nominal Size mm / in 32 x 25 1¼ x 1 40 x 25 1½ x 1 40 x 32 1½ x 1¼ 50 x 25 2 x 1 50 x 32 2 x 1¼ 50 x 40 2 x 1½ 65 x 50 2½ x 2 76.1mm x 50 80 x 25 3 x 1 80 x 32 3 x 1¼ 80 x 40 3 x 1½ 80 x 50 3 x 2 80 x 65 3 x 2.5 80 x 65 3 x 2½ 100 x 50 4 x 2 100 x 65 4 x 2½ 100 x 76.1mm 100 x 80 4 x 3 125 x 100 5 x 4 150 x 50 6 x 2 150 x 65 6 x 2½ 150 x 80 6 x 3 150 x 100 6 x 4 150 x 125 6 x 5 165.1mm x 50 165.1mm x 76.1mm


Pipe O. D. mm / in 42.2 x 33.4 1.660 x 1.315 48.3 x 33.4 1.900 x 1.315 48.3 x 42.2 1.900 x 1.660 60.3 x 33.4 2.375 x 1.315 60.3 x 42.2 2.375 x 1.660 60.3 x 48.3 2.375 x 1.900 73.0 x 60.3 2.875 x 2.375 76.1 x 60.3 3.000 x 2.375 88.9 x 33.4 3.500 x 1.315 88.9 x 42.2 3.500 x 1.660 88.9 x 48.3 3.500 x 1.900 88.9 x 60.3 3.500 x 2.375 88.9 x 73.0 3.500 x 2.875 88.9 x 76.1 3.500 x 3.000 114.3 x 60.3 4.500 x 2.375 114.3 x 73.0 4.500 x 2.875 114.3 x 76.1 4.500 x 3.000 114.3 x 88.9 4.500 x 3.500 141.3 x 114.3 5.563 x 4.500 168.3 x 60.3 6.625 x 2.375 168.3 x 73.0 6.625 x 2.875 168.3 x 88.9 6.625 x 3.500 168.3 x 114.3 6.625 x 4.500 168.3 x 141.3 6.625 x 5.563 165.1 x 60.3 6.500 x 2.375 165.3 x 76.1 6.5.00 x 3.000

#7150 Conc. Reducer E - E Weight mm / in Kgs / Lbs 64 0.20 2.50 0.44 64 0.23 2.50 0.51 64 0.28 2.50 0.62 64 0.37 2.50 0.82 64 0.33 2.50 0.73 64 0.35 2.50 0.77 64 0.59 2.50 1.30 64 0.59 2.50 1.30 64 0.6 2.50 1.3 64 0.6 2.50 1.3 64 0.6 2.50 1.5 64 0.6 2.50 1.3 64 0.6 2.50 1.3 64 0.6 2.50 1.3 76 0.91 3.00 2.01 76 0.98 3.00 2.16 76 1.03 3.00 2.27 76 1.0 3.00 2.2 89 1.61 3.50 3.55 102 1.9 4.00 4.2 102 2.0 4.00 4.4 102 2.0 4.00 4.4 102 2.1 4.00 4.6 102 2.5 4.00 5.5 102 1.9 4.00 4.2 102 1.9 4.00 4.2


#7151 Ecc. Reducer E - E Weight mm / in Kgs / Lbs --- ----- ----- ----- ----- ----- ----- ----- ----- ----- ----- ----- --89 0.65 3.50 1.44 89 0.72 3.50 1.58 --- ----- ----- ----- ----- ----- --89 1.0 3.50 2.2 89 1.0 3.50 2.2 89 1.0 3.50 2.2 102 1.29 4.00 2.85 102 1.5 4.00 3.3 102 1.5 4.00 3.3 102 1.34 4.00 2.95 102 2.8 4.00 6.17 102 2.0 4.00 4.41 --- 3.07 --- 6.77 102 3.5 4.00 7.7 102 2.65 4.00 5.84 102 4.5 4.00 9.9 102 2 4.00 4.41 --- ----- ---

Nominal Size mm / in 200 x 80 8 x 3 200 x 100 8 x 4 200 x 150 8 x 6 250 x 100 10 x 4 250 x 150 10 x 6 250 x 200 10 x 8 300x150 12 x 6 300 x 200 12 x 8 300 x 250 12 x 10 350 x 200 14 x 8 350 x 250 14 x 10 350 x 300 14 x 12 400 x 200 16 x 8 400 x 300 16 x 12 400 x 350 16 x 14 450 x 300 18 x 12 450 x 350 18 x 14 450 x 400 18 x 16 500 x 300 20 x 12 500 x 400 20 x 16 500 x 450 20 x 18 600 x 250 24 x 10 600 x 300 24 x 12 600 x 400 24 x 16 600 x 450 24 x 18 600 x 500 24 x 20

Pipe O. D. mm / in 219.1 x 88.9 8.625 x 3.500 219.1 x 114.3 8.625 x 4.500 219.1 x 168.3 8.625 x 6.625 273.0 x 114.3 10.750 x 4.500 273.0 x 168.3 10.750 x6.625 273.0 x 219.1 10.750 x 8.625 323.9 x 168.3 12.750 x 6.625 323.9 x 219.1 12.750 x 8.625 323.9 x 273.0 12.750 x 10.750 355.6 x 219.1 14.000 x 8.625 355.6 x 273.0 14.000 x 10.750 355.6 x 323.9 14.000 x 12.750 406.4 x 219.1 16.000 x 8.625 406.4 x 323.9 16.000 x 12.750 406.4 x 355.6 16.000 x 14.000 457.2 x 323.9 18.000 x 12.750 457.2 x 355.6 18.000 x 14.000 457.2 x 406.4 18.000 x 16.000 508.0 x 406.4 20.000 x 16.000 508.0 x 406.4 20.000 x 18.000 508.0 x 457.2 20.000 x 16.000 609.6 x 273.0 24.000 x 10.750 609.6 x 323.9 24.000 x 12.750 609.6 x 406.4 24.000 x 16.000 609.6 x 457.2 24.000 x 18.000 609.6 x 508.0 24.000 x 20.000

E-E

7151 Ecc. Reducer #7150 Conc. Reducer E - E Weight mm / in Kgs / Lbs 127 4.3 5.00 9.48 127 5.1 5.00 11.2 127 5.2 5.00 11.4 152 9.0 6.00 19.8 152 9.0 6.00 19.8 152 9.5 6.00 20.9 178 14.0 7.00 30.87 178 14.0 7.00 30.8 178 13.66 7.00 30.12 203 19.0 8.00 41.8 330 23.59 13.00 52.01 330 23.0 13.00 50.71 229 23.7 9.00 52.25 356 31.0 14.00 68.34 356 29.0 14.02 63.93 241 35.5 9.50 78.1 381 36.5 15.00 80.47 381 31.27 15.00 68.94 381 43.0 15.00 94.6 508 46.0 20.00 101.41 254 46.0 10.00 101.2 305 36.0 12.00 79.2 305 70.0 12.00 154.0 305 59.5 12.00 131.18 508 48.5 20.00 106.92 508 71.0 20.00 156.53

www.shurt.com

#7151 Ecc. Reducer E - E Weight mm / in Kgs / Lbs --- ----- --127 5.26 5.00 11.60 127 5.46 5.00 12.03 152 12.0 6.00 26.4 152 11.5 6.00 25.3 178 12.17 7.00 26.83 178 18.0 7.00 39.6 178 18.5 7.00 40.79 178 20.0 7.00 44.10 --- ----- --330 21.0 13.00 46.30 330 26.5 13.00 58.4 --- ----- --356 31.0 14.02 68.34 356 36.5 14.02 80.47 --- ----- --381 39.5 15.00 87.0 381 31.00 15.00 68.34 --- ----- ----- ----- ----- ----- ----- ----- ----- ----- ----- ----- ----- ----- ----- ----- ---

MODEL

MODEL

Catalog 2011

MODEL

7160T TRANSITION CAP 7160H domed end CAP

7160 END CAP

Shurt Model 7160T is an ideal transition

Shurt 7160H end caps are cast of ductile

fitting when a large reduction is required and

iron and are designed to withstand pressure

can be used in place of more costly reducers

evenly over the entire spherical surface. The

or swaged nipples. In addition the 7160T can

Model 7160H End Cap is designed for use

serve as a drain fitting.

on 10” - 24” mechanical piping applications.

E-E 1” ~ 12”

Pipe O.D. mm / in 33.4 1.315 42.2 1.660 48.3 1.900 60.3 2.375 73.0 2.875 76.1 3.000 88.9 3.500 114.3 4.500 108.0 4.250 141.3 5.563 133.0 5.250 139.7 5.500 168.3 6.625 159.0 6.250 165.1 6.500 219.1 8.625 273.0 10.750 323.9 12.750 216.3 8.516 267.4 10.528 318.5 12.539

#7160 End Cap E - E Weight mm / in Kgs / Lbs 22 0.1 0.87 0.2 25 0.15 1.00 0.33 25 0.2 1.00 0.4 25 0.3 1.00 0.7 25 0.4 1.00 0.9 25 0.4 1.00 0.9 25 0.7 1.00 1.5 25 1.0 1.00 2.2 25 1.1 1.00 2.4 25 1.7 1.00 3.7 25 1.7 1.00 3.7 25 1.7 1.00 3.7 25 2.7 1.0 5.96 25 2.3 1.00 5.1 25 2.7 1.00 5.96 30 4.6 1.18 10.14 32 7.0 1.25 15.4 32 10.0 1.25 22.0 30 4.6 1.18 10.1 32 7.0 1.25 15.4 32 10.0 1.25 22.0

SW: segment-welded steel.

MODEL

7160P END CAP w/PLUG

L

Nominal Size Grooved x Threaded mm / in 50 x 25 2 x 1 50 x 32 2 x 1¼ 65 x 25 2½ x 1 65 x 32 2½ x 1¼ 65 x 40 2½ x 1½ 80 x 25 3 x 1 80 x 32 3 x 1¼ 80 x 40 3 x 1½ 80 x 50 3 x 2 100 x 25 4 x 1 100 x 32 4 x 1¼ 100 x 40 4 x 1½ 100 x 50 4 x 2 150 x 25 6 x 1 150 x 32 6 x 1¼ 150 x 40 6 x 1½ 150 x 50 6 x 2

Nominal Size mm / in 50 2 65 2½ 76.1 mm 80 3 100 4 125 5


L mm / in 23.8 0.94 23.8 0.94 23.8 0.94 23.8 0.94 23.8 0.94 25.4 1.0 25.4 1.0 25.4 1.0 25.4 1.0 25.4 1.0 25.4 1.0 25.4 1.0 25.4 1.0 25.4 1.0 25.4 1.0 25.4 1.0 25.4 1.0

Pipe O.D. mm / in 60.3 2.375 73.0 2.875 76.1 3.000 88.9 3.500 114.3 4.500 141.3 5.563

7160T

Weight Kgs / Lbs 0.25 0.55 0.25 0.55 0.44 0.97 0.35 0.77 0.30 0.70 0.65 1.43 0.65 1.43 0.60 1.30 0.60 1.33 0.95 2.09 0.95 2.09 0.90 2.00 0.90 1.98 2.50 5.52 2.50 5.52 2.50 5.50 2.50 5.50

7160P Plug Size mm / in 15 ½ 15 ½ 15 ½ 15 0.5 25 1 25 1

E-E

Nominal Size mm / in 25 1 32 1¼ 40 1½ 50 2 65 2½ 76.1 mm 80 3 100 4 108 mm 125 5 133 mm 139.7 mm 150 6 159.0 mm 165.1 mm 200 8 250 10 300 12 200 JIS 250 JIS 300 JIS

10” ~ 24” Nominal Size mm / in 250 10 300 12 350 14 400 16 450 18 500 20 550 22 600 24

Pipe O.D. mm / in 273.0 10.750 323.90 12.750 355.6 14.000 406.4 16.000 457.2 18.000 508.0 20.000 558.8 22.000 609.6 24.000

Nominal Size mm / in 139.7 mm 150 6 165.1 mm 200 8 250 10 300 12

www.shurt.com

#7160H Domed End Cap E - E Weight mm / in Kgs / Lbs 76.1 5.5 3.00 12.1 76.1 7.4 3.00 16.3 102 11.95 4.00 26.35 102 14.5 4.00 31.97 127 17.8 5.00 39.24 152 24.5 6.00 53.9 152 44.0 6.00 97.0 152 34.5 6.00 75.9

Pipe O.D. mm / in 139.7 5.500 168.3 6.625 165.1 6.500 219.1 8.625 273.0 10.750 323.9 12.750

7160P Plug Size mm / in 25 1 25 1 25 1 40 1½ 40 1½ 40 1½


Catalog 2011

MODELS

Nominal Size mm / in 50 2 65 2½ 76.1 mm 80 3 100 4 125 5 139.7 mm 150 6 165.1 mm 200 8 250 10 300 12

Pipe O. D. mm / in 60.3 2.375 73.0 2.875 76.1 3.000 88.9 3.500 114.3 4.500 141.3 5.563 139.7 5.500 168.3 6.625 165.1 6.500 219.1 8.625 273.0 10.750 323.9 12.750

7110LR LR 90˚ Elbow, 1.5D

#7110LR 1.5D LR 90˚ Elbow C - E mm / in Kgs / Lbs 111 1.1 4.38 2.4 127 1.8 5.0 4.0 127 1.8 5.0 4.0 149 1.8 5.88 4.0 191 4.7 7.50 10.3 241 8.3 9.50 18.3 241 8.3 9.50 18.3 273 11.5 10.75 25.3 273 11.5 10.75 25.3 362 23.0 14.25 50.7 438 42.2 17.25 73.0 521 71.5 20.50 157.6

C-SE

C-E

C-E

C

-L

E

7110LR 1.5D 90° elbow 7111LR 1.5D 45° elbow 7137 TRUE-Y

7137 True-Y

7111LR LR 45˚ Elbow, 1.5D

#7111LR 1.5D LR 45˚ Elbow C - E C - LE mm / in Kgs / Lbs mm / in 70 0.8 83 2.75 1.8 3.25 76 1.4 95 3.00 3.1 3.75 76 1.45 95 3.00 3.20 3.75 86 1.8 108 3.38 3.97 4.25 102 3.5 127 4.00 7.7 5.00 127 4.6 140 5.0 10.14 5.50 127 4.6 140 5.0 10.14 5.50 140 8.2 165 5.50 18.0 6.50 140 8.2 165 5.50 18.0 6.50 184 16.0 197 7.25 35.27 7.75 216 36.1 229 8.50 78.59 9.00 254 33.5 254 10.00 73.86 10.00

#7137 TRUE-Y C - SE mm / in 70 2.75 76 3.00 76 3.00 83 3.25 95 3.75 102 4.00 102 4.00 114 4.50 114 4.50 152 6.00 165 6.50 178 7.00

Kgs / Lbs 1.1 2.5 1.7 3.75 1.8 3.97 2.50 5.51 4.7 10.43 5.3 11.60 6.8 14.96 8.9 19.62 8.9 19.62 15.6 34.33 25.5 56.22 36.0 79.37

MODELS

7112G Goose Neck

22-½° Elbow

Two model 7112G elbows in combination with a coupling will serve as a universal t and is ideal for instances where a pipe

MODEL

7110-B 90° ELBOW With Base The Model 7110-B is a ductile iron 90°

riser system. An anchor can be placed in

grooved-end elbow with base ,

conjunction with the base to the

designed for installation at the bottom of a

weight of the pipe, coupling and fluid.

line is in need of a slight adjustment during

C-E C-E

make-up.

T

U Nominal Size mm / in 40 1½ 50 2 65 2½ 80 3 100 4 125 5 150 6 200 8 200JIS


Pipe 7112G 22½° Elbows O.D. E - E Weight mm / in mm / in Kgs / Lbs 48.3 95 G 0.6 1.900 3.75 1.3 60.3 95 G 0.8 2.375 3.75 1.3 73.0 102 G 1.0 2.875 4.00 2.2 88.9 114 G 1.4 3.500 4.50 3.1 114.3 127 G 2.0 4.500 5.00 4.4 141.3 127 G 3.3 5.563 5.00 7.3 168.3 159 G 5.0 6.625 6.25 11.0 219.1 197 G 10.0 8.625 7.75 22.0 216.3 197 G 10.0 8.516 7.75 22.0

H

E-E

S

M



Pipe Dimensions O. D. C - E H U T S M mm / in mm / in mm / in mm / in mm / in mm / in mm / in 88.9 108 124 13 14 127 99 3.500 4.25 4.88 0.50 0.56 5.00 3.88 114.3 127 140 13 16 152 121 4.500 5.00 5.50 0.50 0.62 6.00 4.75 168.3 165 178 16 18 178 140 6.625 6.50 7.00 0.62 0.69 7.00 5.50 219.1 197 213 22 24 229 191 8.625 7.76 8.38 0.88 0.94 9.00 7.50 273.0 229 248 22 24 229 191 10.750 9.02 9.75 0.88 0.94 9.00 7.50 323.9 254 286 25 25 279 241 12.750 10.00 11.25 1.00 1.00 11.00 9.50

www.shurt.com

Weight Kgs / Lbs 4.75 10.47 6.91 15.23 11.93 26.30 46.1 101.4 20.00 44.00 32.00 70.40

Catalog 2011

MODELS

901 90° SR ELBOW 903 SR tee Shurt short radius fittings, while primarily designed for fire protection applications, can also be used for general service requirements.

C-E

C-E Nominal Pipe Size mm / in 50 2 65 2½ 76.1mm 80 3 100 4 125 5 125 5 165.1mm 150 6 200 8

Pipe O.D. mm / in 60.3 2.375 73.0 2.875 76.1 3.000 88.9 3.500 114.3 4.500 139.7 5.500 141.3 5.563 165.1 6.500 168.3 6.625 219.1 8.625

#901 SR 90˚ Elbow C - E Weight mm / in Kgs / Lbs 70 0.7 2.75 1.5 76 0.9 3.00 2.0 76 1.1 3.00 2.5 86 1.4 3.38 3.1 102 2.2 4.00 4.9 124 3.6 4.88 7.9 124 3.6 4.88 7.9 140 5.9 5.50 12.9 140 5.9 5.50 12.9 176 10.6 6.94 23.4

MODEL

E

The Model 7110DR is a grooved-end ductile

D

iron cast elbow with an integral 1" NPT or use in fire protection and general service applications.

#903 SR Straight Tee C - E Weight mm / in Kgs / Lbs 70 1.0 2.75 2.2 76 1.3 3.00 2.9 76 1.3 3.00 2.9 86 2.0 3.38 4.4 102 3.6 4.00 7.9 124 5.1 4.88 11.1 124 4.6 4.88 10.1 140 7.5 5.50 16.5 140 7.8 5.50 17.2 176 16.5 6.94 36.3

C-E

7110DR DRAIN ELBOW BSP drain. The 7110DR is designed for

C-E

C-E

Nominal Pipe Size mm / in 50 2 65 2½ 76.1mm 80 3 100 4 165.1mm 150 6 200 8

Pipe O.D. C - E mm / in mm / in 60.3 83 2.375 3.27 73.0 95 2.875 3.75 76.1 95 3.000 3.75 88.9 108 3.500 4.25 114.3 127 4.500 5.00 165.1 165 6.500 6.50 168.3 165 6.625 6.50 219.1 197 8.625 7.76

1" NPT

Dimensions D mm / in 57.2 2.25 70 2.75 70 2.75 70 2.75 70 2.75 70 2.75 70 2.75 83 3.27

MODEL

7127 STANDPIPE TEE

E mm / in 40 1.57 40 1.57 40 1.57 49 1.93 63 2.48 90 3.54 90 3.54 114 4.49

Weight Kgs / Lbs 1.0 2.2 1.3 2.8 1.3 2.8 2.1 4.6 3.0 6.6 6.1 13.4 6.1 13.4 11.6 25.6

C-EB NPT or BSP

The Model 7127 is a grooved-end tee C-ER

with a 2½" NPT/BSP threaded branch, specially designed for use on fire protection standpipes.


Nominal Size mm / in 100 x 100 x 65 4 x 4 x 2½ 150 x 150 x 65 6 x 6 x 2½

Pipe O.D. mm / in 114.3 x 114.3 x 73.0 4.500 x 4.500 x 2.875 168.3 x 168.3 x 73.0 6.625 x 6.625 x 2.875

C - ER mm / in 83 3.25 83 3.25

Dimensions

C - EB mm / in 102 4.00 127 5.00

www.shurt.com

Weight Kgs / Lbs 2.65 5.84 4.30 9.48


Catalog 2011

MODEL

7125 BULLHEAD TEE C-EB

C-ER

The Model 7125 is a grooved-end bullhead tee, specifically designed for use on fire protection systems. The 7125 allows you to directly split the flow into two reduced branch lines without the need for concentric reducers and multiple couplings. Fire Protection Applications 7125 Bullhead Tee Waterflow Indicator RCV Riser Check Valve With Trim Kit

SJ-700W Butterfly Valve 7707/7705 Flexible Couplings Z07/7771 Rigid Couplings

Nominal Pipe Size mm / in 50 x 50 x 65 2 x 2 x 2½ 50 x 50 x 80 2 x 2 x 3 50 x 50 x 100 2 x 2 x 4 65 x 65 x 80 2½ x 2½ x 3 65 x 65 x 100 2½ x 2½ x 4 80 x 80 x 100 3 x 3 x 4 100x 100 x 150 4 x 4 x 6 125 x 125 x 200 5 x 5 x 8 150 x 150 x 200 6 x 6 x 8

Pipe O.D. mm / in 60.3 x 60.3 x 73.0 2.375 x 2.375 x 2.875 60.3 x 60.3 x 88.9 2.375 x 2.375 x 3.500 60.3 x 60.3 x 114.3 2.375 x 2.375 x 4.500 73.0x 73.0 x 88.9 2.875 x 2.875 x 3.500 73.0 x 73.0 x 114.3 2.875 x 2.875 x 4.500 88.9 x 88.9 x 114.3 3.500 x 3.500 x 4.500 114.3 x 114.3 x 168.3 4.500 x 4.500 x 6.625 141.3 x 141.3 x 219.1 5.563 x 5.563 x 8.625 168.3 x 168.3 x 219.1 6.625 x 6.625 x 8.625

C - ER mm / in 95 3.74 108 4.25 127 5.00 108 4.25 127 5.00 127 5.00 165 6.50 197 7.75 197 7.75

Dimensions

C - EB mm / in 83 3.27 95 3.74 102 4.02 95 3.75 102 4.00 102 4.00 127 5.00 140 5.50 165 6.50

Weight Kgs / Lbs 1.83 4.03 1.97 4.34 3.20 7.05 2.55 5.62 3.32 7.32 3.60 7.94 6.80 14.99 14.00 31.00 13.21 29.12

MODEL

7150F REDUCING SOCKET (Gr x Ft) 7150M REDUCING NIPPLE (Gr x Mt) The Shurt Models 7150F & 7150M are designed for making a direct reduction from a grooved system to a female or male threaded system without the need for more costly swaged nipples or adapters.

7150F

7150M

L

L


Nominal Size 7150F 7150M Grooved x Threaded L Weight L Weight mm / in mm / in Kgs / Lbs mm / in Kgs / Lbs 40 x 25 63.5 0.27 63.5 0.24 1½ x 1 2.5 0.60 2.5 0.53 50 x 25 63.5 0.42 63.5 0.40 2 x 1 2.5 0.92 2.5 0.88 50 x 32 63.5 0.46 63.5 0.32 2 x 1¼ 2.5 1.01 2.5 0.70 50 x 40 63.5 0.43 63.5 0.47 2 x 1½ 2.5 0.95 2.5 1.04 65 x 25 63.5 0.55 63.5 0.40 2 ½ x 1 2.5 1.21 2.5 0.88 63.5 0.55 63.5 0.75 76.1mm x 25 2.5 1.21 2.5 1.64 65 x 32 63.5 0.53 63.5 0.72 2 ½ x 1¼ 2.5 1.17 2.5 1.59 63.5 0.53 63.5 0.72 76.1mm x 32 2.5 1.17 2.5 1.59 65 x 40 63.5 0.49 63.5 0.78 2 ½ x 1½ 2.5 1.08 2.5 1.72 63.5 0.49 63.5 0.78 76.1mm x 40 2.5 1.08 2.5 1.72 65 x 50 63.5 0.69 63.5 0.42 2½ x 2 2.5 1.52 2.5 0.92 63.5 0.69 63.5 0.49 76.1mm x 50 2.5 1.52 2.5 1.09 80 x 25 63.5 0.87 63.5 0.57 3 x 1 2.5 1.91 2.5 1.25 80 x 32 63.5 0.68 63.5 0.76 3 x 1¼ 2.5 1.50 2.5 1.67 80 x 40 63.5 0.74 63.5 0.74 3 x 1½ 2.5 1.63 2.5 1.63 80 x 50 63.5 0.71 63.5 0.60 3 x 2 2.5 1.56 2.5 1.32 80 x 65 63.5 1.00 63.5 1.00 3 x 2½ 2.5 2.20 2.5 2.20


Nominal Size 7150F 7150M Grooved x Threaded L Weight L Weight mm / in mm / in Kgs / Lbs mm / in Kgs / Lbs 63.5 1.00 63.5 1.00 80 x 76.1mm 2.5 2.20 2.5 2.20 100 x 32 76.1 1.06 76.1 0.99 4 x 1¼ 3 2.33 3 2.19 100 x 40 76.1 0.93 76.1 0.93 4 x 1½ 3 2.05 3 2.05 100 x 50 76.1 1.03 76.1 1.05 4 x 2 3 2.29 3 2.31 100 x 65 76.1 1.02 76.1 0.93 4 x 2½ 3 2.25 3 2.05 76.1 1.02 76.1 0.93 100 x 76.1mm 3 2.25 3 2.05 125 x 40 88.9 1.79 88.9 0.93 5 x 1½ 3.5 3.94 3.5 2.05 88.9 1.79 88.9 0.93 139.7mm x 40 3.5 3.94 3.5 2.05 150 x 40 101.6 2.94 101.6 2.20 6 x 1½ 4 6.47 4 4.84 101.6 2.52 101.6 2.16 165.1mm x 40 4 5.56 4 4.75 150 x 50 101.6 2.40 101.6 2.23 6 x 2 4 5.28 4 4.91 101.6 2.40 101.6 2.23 165.1mm x 50 4 5.28 4 4.91 150 x 65 101.6 2.48 101.6 2.26 6 x 2½ 4 5.46 4 4.97 101.6 2.00 101.6 2.26 165.1mm x 65 4 4.40 4 4.97 150 x 100 101.6 2.89 101.6 2.10 6 x 4 4 6.37 4 4.62 101.6 2.10 101.6 2.10 165.1mm x 100 4 4.62 4 4.62

www.shurt.com

Catalog 2011

MODEL

899 END-ALL FITTING The Model 899 End-All fitting is a unique domed end cap fitting available with a ½”, ¾” or 1” NPT or BSP threaded outlet. Designed as an end of line fitting, the EndAll features two multi-function bosses which can be used for the direct connection of sprinkler heads, sprigs, drops, drains and or gauges.

B A

NPT or BSP

MODEL

55 ADAPTER NIPPLE

(Gr x MT)

Nominal Size Grooved x Threaded A mm / in mm / in 32 x 15 44.5 1¼ x ½ 1.750 32 x 20 44.5 1¼ x ¾ 1.750 32 x 25 48.3 1¼ x 1 1.900 40 x 15 44.5 1½ x ½ 1.750 40 x 20 44.5 1½ x ¾ 1.750 40 x 25 48.3 1½ x 1 1.900 50 x 15 44.5 2 x ½ 1.750 50 x 20 44.5 2 x ¾ 1.750 50 x 25 48.3 2 x 1 1.900 65 x 15 44.5 2½ x ½ 1.750 65 x 20 44.5 2½ x ¾ 1.750 65 x 25 48.3 2½ x 1 1.900

Dimensions

B mm / in 30.1 1.190 30.1 1.190 31.8 1.250 33.3 1.313 33.3 1.313 34.9 1.375 39.7 1.562 39.7 1.562 41.3 1.625 44.5 1.750 44.5 1.750 46.0 1.813

Weight Kgs / Lbs 0.3 0.7 0.3 0.7 0.3 0.7 0.4 0.9 0.4 0.9 0.4 0.9 0.5 1.1 0.5 1.1 0.5 1.1 0.6 1.3 0.6 1.3 0.6 1.3

MODEL

56 HOSE NIPPLE The Shurt Model 56 hose nipple allows

The Shurt Model 55 is an integral cast adapter that allows for a direct transition from a grooved system to a male threaded system or component. For other sizes see

for a direct connection with rubber or plastic hoses.

E-E

Material: Ductile iron ASTM A536 Gr. 65-4512 and or ASTM A395 Gr. 65-45-15.

page 55, Models 57 through 59 nipples adapters.

NPT or BSP

L

Nominal Size Grooved x Threaded mm / in 40 x 40M 1½ x 1½M 50 x 50M 2 x 2M

L mm / in 63.5 2.50 63.5 2.50

Weight Kgs / Lbs 0.35 0.77 0.40 0.90


Nominal Size mm / in 32 1¼ 40 1½ 50 2 65 2½ 80 3 100 4 125 5 150 6 200 8

Pipe O.D. mm / in 42.2 1.660 48.3 1.900 60.3 2.375 73.0 2.875 88.9 3.500 114.3 4.500 141.3 5.563 168.3 6.625 219.1 8.625

www.shurt.com

E - E mm / in 92 3.6 102 4.0 117 4.6 140 5.5 152 6.0 184 7.25 248 9.75 279 11.0 318 12.5

Weight Kgs / Lbs 0.3 0.7 0.3 0.7 0.6 1.2 1.0 2.2 1.5 3.3 2.5 5.5 3.7 8.1 6.6 14.5 11.0 24.2


Catalog 2011

Sprinkler Hubs The Shurt Sprinkler Hubs are grooved-end manifold fittings with a number of threaded outlets to accommodate flexible sprinkler hoses. The Sprinkler Hubs can also be used in combination with flexible sprinkler hoses and traditional hard piping depending on your requirements. These fittings work as a hub for multiple flexible hoses and or hard pipe runs, thus reducing the number or headers, drop nipples and fittings required. All outlets are 1” NPT or BSPT. Maximum working pressure is 300 psi (20 bar, 2.0 MPa) CWP. cULus listed and FM approved. The C-to-E dimensions conform to ANSI B16.3 Class 150.

MODEL

850 Sprinkler Hub 3 Outlets

MODEL

853 Sprinkler End Hub 4 Outlets A

B

B

A

B

A

Size A mm / in mm / in 50 x 50 x 25 (3) 60 2 x 2 x 1 (3) 2.38 65 x 65 x 25 (3) 60 2½ x 2½ x 1 (3) 2.38

B mm / in 51 2.02 57 2.25

N.W. Kgs / Lbs 0.90 2.00 1.25 2.75

( ): Number of outlets

Size A mm / in mm / in 40 x 25 (4) 60 1½ x 1 (4) 2.38 50 x 25 (4) 60 2 x 1 (4) 2.38 65 x 25 (4) 60 2½ x 1 (4) 2.38

B mm / in 46 1.80 51 2.02 57 2.25

( ): Number of outlets MODEL

851 Reducing Sprinkler Hub

3 Outlets

B

A

A

Size A mm / in mm / in 50 x 40 x 25 (3) 60 2 x 1½ x 1 (3) 2.38 65 x 40 x 25 (3) 60 2½ x 1½ x 1 (3) 2.38 65 x 50 x 25 (3) 60 2½ x 2 x 1 (3) 2.38

B mm / in 51 2.02 57 2.25 60 2.25

N.W. Kgs / Lbs 1.14 2.52 1.20 2.65 1.23 2.71

( ): Number of outlets



www.shurt.com

N.W. Kgs / Lbs 0.74 1.63 0.88 1.94 1.15 2.54

Catalog 2011

MODEL

7114 Hydrant ELBOW 2½" BSP Threaded

The Model 7114 Hydrant Elbow is designed C-BE

for use on fire protection systems. The small

3" Grooved

end of the elbow offers both a 2½" BSP threaded outlet as well as a 3" grooved

Boss

connection. The boss can be factory tapped to 1" BSP on request.

C-E

Nominal Pipe Size mm / in 100 x 80 x 25 4 x 3 x 1 150 x 80 x 25 6 x 3 x 1


C - E mm / in 102 4.00 130 5.13

Dimensions

C - BE mm / in 95 3.75 130 5.13

Weight Kgs / Lbs 2.70 5.95 4.0 8.8

MODEL

7122 Hydrant TEE

3" Grooved C-BE

The Model 7122 Hydrant Tee is designed

2½" BSP Threaded

for use on fire protection systems. The 7122 tee offers both a 2½" BSP threaded and a

Boss

3" grooved outlet. The boss can be factory tapped to 1" BSP on request.

C-E Nominal Pipe Size mm / in 100 x 100 x 80 4 x 4 x 3 165.1 x 165.1 x 80 6 x 6 x 3


C - E mm / in 102 4.00 130 5.13

Dimensions

C - BE mm / in 102 4.00 130 5.13

Weight Kgs / Lbs 3.50 7.72 5.54 12.21

MODEL

7133 PITCHER TEE

B C

The Shurt pitcher tee provides a quick and easy connection and transition from a

A

grooved riser system to a threaded hydrant valve outlet. The pitcher tee is designed

2½ BSP threaded 3" Grooved

for 3", 4" and 6" steel pipe risers with a 2½" BSP threaded or 3" grooved hydrant connection outlet.

Nominal Pipe Size mm / in 80 x 80 x 76.1mm 100 x 100 x 76.1mm 165.1 x 165.1 x 76.1mm


Pip O.D. mm / in 88.9 x 88.9 x 76.1 3.500 x 3.500 x 3.000 114.3 x 114.3 x 76.1 4.500 x 4.500 x 3.000 165.1 x 165.1 x 76.1 6.500 x 6.500 x 3.000

Hydrant Outlet A mm / in mm / in BSP 121 Taper 4.75 BSP 121 Taper 4.75 BSP 121 Taper 4.75

Dimensions Approx. B C Weight mm / in mm / in Kgs / Lbs 121 69 2.8 4.75 2.72 6.2 133 69 3.4 5.25 2.72 7.5 159 69 8.7 6.25 2.72 19.1

www.shurt.com


WROUGHT GROOVED FITTINGS MODEL

W110 90° ELBOW, S/R W120 TEE

Catalog 2011

W110LR 90° ELBOW, L/R W160 CAP

W111LR 45° ELBOW

Shurt wrought steel grooved fittings are fabricated from standard weight (0.375” or

E-E

9.5mm) carbon steel pipe to ASTM A234 Gr. WPB, or segmentally welded with carbon steel of the same or equivalent grade. C-E dimensions conform to ANSI B16.9.


Pipe O.D. mm / in 355.6 14.000 406.4 16.000 457.2 18.000 508.0 20.000 558.8 22.000 609.6 24.000

W110

W110 90° S/R Elbows C-E Weight mm / in Kgs / Lbs 355.6 45.3 14.00 99.7 406.4 59.1 16.00 130.0 457.2 75.3 18.00 165.7 508.0 93.1 20.00 204.8 558.8 113.0 22.00 248.6 609.6 135.0 24.00 297.0

C-E

C-E

W110LR

W110LR 90° L/R Elbows C-E Weight mm / in Kgs / Lbs 533.4 67.9 21.00 149.4 609.6 89.0 24.00 195.8 685.8 113.0 27.00 248.6 762.0 140.0 30.00 308.0 838.2 169.0 33.00 371.8 914.4 202.0 36.00 444.4

C-E

C-E W111LR

W111LR 45° L/R Elbows C-E Weight mm / in Kgs / Lbs 222.3 34.0 8.75 74.8 254.0 44.6 10.00 98.1 285.5 56.5 11.25 124.3 317.5 70.0 12.50 154.0 342.9 85.0 13.50 187.0 381.0 101.0 15.00 222.2

C-E W120

W120 Tee C-E Weight mm / in Kgs / Lbs 279.4 53.5 11.00 117.7 304.8 66.1 12.00 145.4 342.9 83.9 13.50 184.6 381.0 104.0 15.00 228.8 419.1 126.0 16.50 277.2 431.8 139.0 17.00 305.8

W160 W160 Cap E-E Weight mm / in Kgs / Lbs 165.0 15.9 6.50 35.0 178.0 20.0 7.00 44.0 203.0 25.5 8.00 56.1 229.0 31.8 9.00 70.0 254.0 38.8 10.00 85.4 267.0 45.1 10.50 99.2

MODEL

W121 Reducing Tee Material: ASTM A234 Gr. WPB, standard weight (0.375” or 9.5mm), or carbon steel of

C-E

the same or equivalent grade.

C-B

C-E & C-B dimensions conform to ANSI

W121

B16.9

Nominal Size mm / in 350 x 150 14 x 6 350 x 200 14 x 8 350 x 250 14 x 10 350 x 300 14 x 12 400 x 150 16 x 6 400 x 200 16 x 8 400 x 250 16 x 10 400 x 300 16 x 12 400 x 350 16 x 14 450 x 150 18 x 6 450 x 200 18 x 8 450 x 250 18 x 10 450 x 300 18 x 12 450 x 350 18 x 14 450 x 400 18 x 16


Pipe O. D. mm / in 355.6 x 168.3 14.000 x 6.625 355.6 x 219.1 14.000 x 8.625 355.6 x 273.0 14.000 x 10.750 355.6 x 323.9 14.000 x 12.750 406.4 x 168.3 16.000 x 6.625 406.4 x 219.1 16.000 x 8.625 406.4 x 273.0 16.000 x 10.750 406.4 x 323.9 16.000 x 12.750 406.4 x 355.6 16.000 x 14.000 457.2 x 168.3 18.000 x 6.625 457.2 x 219.1 18.000 x 8.625 457.2 x 273.0 18.000 x 10.750 457.2 x 323.9 18.000 x 12.750 457.2 x 355.6 18.000 x 14.000 457.2 x 406.4 18.000 x 16.000

W121 Reducing Tee C - E C - B mm / in mm / in 279.0 238.0 11.0 9.37 279.0 248.0 11.0 9.76 279.0 257.0 11.0 10.12 279.0 270.0 11.0 10.63 30.50 264.0 12.0 10.40 305.0 273.0 12.0 10.75 305.0 282.0 12.0 11.10 305.0 295.0 12.0 11.61 305.0 305.0 12.0 12.00 343.0 289.0 13.5 11.38 343.0 298.0 13.5 11.38 343.0 308.0 13.5 12.13 343.0 321.0 13.5 12.64 343.0 330.0 13.5 13.00 343.0 330.0 13.5 13.00


Weight Kgs / Lbs 46.0 101.20 46.5 102.30 47.7 104.94 44.0 96.8 57.2 125.84 57.8 127.16 58.9 129.58 60.1 132.22 61.1 134.42 72.6 159.72 73.0 160.60 74.0 162.80 75.1 165.22 76.0 167.20 76.3 167.86

Nominal Size mm / in 500 x 150 20 x 6 500 x 200 20 x 8 500 x 250 20 x 10 500 x 300 20 x 12 500 x 350 20 x 14 500 x 400 20 x 16 500 x 450 20 x 18 600 x 150 24 x 6 600 x 200 24 x 8 600 x 250 24 x 10 600 x 300 24 x 12 600 x 350 24 x 14 600 x 400 24 x 16 600 x 450 24 x 18 600 x 500 24 x 20

Pipe O. D. mm / in 508.0 x 168.3 20.000 x 6.625 508.0 x 219.1 20.000 x 8.625 508.0 x 273.0 18.000 x 10.750 508.0 x 323.9 20.000 x 12.750 508.0 x 355.6 20.000 x 14.000 508.0 x 406.4 20.000 x 16.000 508.0 x 457.2 20.000 x18.000 609.6 x 168.3 20.000 x 6.625 609.6 x 219.1 20.000 x 8.625 609.6 x 273.0 24.000 x 10.750 609.6 x 323.9 24.000 x 12.750 609.6 x 355.6 24.000x14.000 609.6 x 406.4 24.000 x 16.000 609.6 x 457.2 24.000x18.000 609.6 x 508.0 24.000 x 20.000

W121 Reducing Tee C - E C - B mm / in mm / in 381.0 314.0 15.0 12.36 381.0 324.0 15.0 12.76 381.0 333.0 18.0 13.11 381.0 346.0 15.0 13.62 381.0 356.0 15.0 14.02 381.0 356.0 15.0 14.02 381.0 368.0 15.0 14.50 432.0 365.0 17.0 14.38 432.0 375.0 17.0 14.76 432.0 384.0 17.0 15.12 432.0 397.0 17.0 15.63 432.0 406.0 17.0 16.00 432.0 406.0 17.0 16.00 432.0 419.0 17.0 16.50 432.0 432.0 17.0 17.00

www.shurt.com

Weight Kgs / Lbs 89.5 196.90 90.0 198.0 90.9 199.98 92.0 202.40 92.9 204.38 93.6 204.60 94.5 207.90 122.0 268.40 123.0 270.6 123.2 271.04 124.2 273.24 125.0 275.0 125.0 275.0 127.1 279.62 128.0 281.60

WROUGHT GROOVED FITTINGS

Catalog 2011

MODEL

W150 WROUGHT CONCENTRIC REDUCER W151 WROUGHT ECCENTRIC REDUCER Material: ASTM A234 Gr. WPB, standard

weight (0.375” or 9.5mm), or segmentally welded carbon steel of the same or equivalent grade E-E dimensions conform to ANSI B16.9.

E-E

E-E

W150

W151

MODEL

57 NIPPLE, Groove X Groove 58 NIPPLE, Groove X Bevel 59 NIPPLE, Groove X Thread Model 57 E-E

Gr. x Gr. Model 58 E-E

Gr. x Bev. Model 59 E-E

Gr. x Th

Nominal Pipe Size mm / in 350 x 150 14 x 6 350 x 200 14 x 8 350 x 250 14 x 10 350 x 300 14 x 12 400 x 200 16 x 8 400 x 250 16 x 10 400 x 300 16 x 12 400 x 350 16 x 14 450 x 250 18 x 10 450 x 300 18 x 12 450 x 350 18 x 14 450 x 400 18 x 16 500 x 300 20 x 12 500 x 350 20 x 14 500 x 400 20 x 16 500 x 450 20 x 18 600 x 400 24 x 16 600 x 450 24 x 18 600 x 500 24 x 20

Nominal Pipe Size mm / in 20 ¾ 25 1 32 1¼ 40 1½ 50 2 65 2½ 80 3 100 4 125 5 150 6 200 8 250 10 300 12


Pipe O.D. mm / in 355.6 x 168.3 14.000 x 6.625 355.6 x 219.1 14.000 x 8.625 355.6 x 273.0 14.000 x 10.750 355.6 x 323.9 14.000 x 12.750 406.4 x 219.1 16.000 x 8.625 406.4 x 273.0 16.000 x 10.750 406.4 x 323.9 16.000 x 12.750 406.4 x 355.6 16.000 x 14.000 457.2 x 273.0 18.000 x 10.750 457.2 x 323.9 18.000 x 12.750 457.2 x 355.6 18.000 x 14.000 457.2 x 406.4 18.000 x 16.000 508.0 x 323.9 20.000 x 12.750 508.0 x 355.6 20.000 x 14.000 508.0 x 406.4 20.000 x 16.000 508.0 x 457.2 20.000 x18.000 609.6 x 406.4 24.000 x 16.000 609.6 x 457.2 24.000x18.000 609.6 x 508.0 24.000 x 20.000

Pipe O.D. mm / in 26.7 1.050 33.4 1.315 42.2 1.660 48.3 1.900 60.3 2.375 73.0 2.875 88.9 3.500 114.3 4.500 141.3 5.563 168.3 6.625 219.1 8.625 273.0 10.750 323.9 12.750

W150 Concentric Reducer E-E Weight mm / in Kgs / Lbs 330.0 30.8 13.00 67.76 330.0 31.8 13.00 69.96 330.0 32.7 13.00 71.94 330.0 33.6 13.00 73.92 356.0 39.9 14.00 87.78 356.0 41.3 14.00 90.86 356.0 42.2 14.00 92.84 356.0 43.1 14.00 94.82 381.0 50.8 15.00 111.76 381.0 52.2 15.00 114.84 381.0 53.5 15.00 117.70 381.0 54.9 15.00 120.78 508.0 72.6 20.00 159.72 508.0 74.4 20.00 163.68 508.0 76.2 20.00 167.64 508.0 78.0 20.00 171.6 508.0 89.8 20.00 197.56 508.0 90.7 20.00 199.54 508.0 92.5 20.00 203.50

57 (Gr x Gr) E - E Weight mm / in Kgs / Lbs 76 0.13 3 0.29 76 0.19 3 0.42 102 0.31 4 0.68 102 0.37 4 0.82 102 0.50 4 1.10 102 0.80 4 1.76 102 1.10 4 2.40 152 2.35 6 5.17 152 3.30 6 7.26 152 4.50 6 9.90 152 6.50 6 14.30 203 12.30 8 27.06 203 16.20 8 35.64

W151 Eccentric Reducer E-E Weight mm / in Kgs / Lbs 330.0 30.8 13.00 67.76 330.0 31.8 13.00 69.96 330.0 32.7 13.00 71.94 330.0 33.6 13.00 73.92 356.0 39.9 14.00 87.78 356.0 41.3 14.00 90.86 356.0 42.2 14.00 92.84 356.0 43.1 14.00 94.82 381.0 50.8 15.00 111.76 381.0 52.2 15.00 114.84 381.0 53.5 15.00 117.70 381.0 54.9 15.00 120.78 508.0 72.6 20.00 159.72 508.0 74.4 20.00 163.68 508.0 76.2 20.00 167.64 508.0 78.0 20.00 171.6 508.0 89.8 20.00 197.56 508.0 90.7 20.00 199.54 508.0 92.5 20.00 203.50

58 (Gr x Bev) E - E Weight mm / in Kgs / Lbs 76 0.13 3 0.29 76 0.19 3 0.42 102 0.32 4 0.70 102 0.38 4 0.84 102 0.50 4 1.10 102 0.80 4 1.76 102 1.10 4 2.40 152 2.35 6 5.17 152 3.30 6 7.26 152 4.50 6 9.90 152 6.50 6 14.30 203 8.66 8 19.00 203 10.16 8 22.35

www.shurt.com

59 (Gr x Th) E - E Weight mm / in Kgs / Lbs 76 0.13 3 0.29 76 0.19 3 0.42 102 0.30 4 0.66 102 0.36 4 0.79 102 0.50 4 1.10 102 0.72 4 1.54 102 1.00 4 2.20 152 2.20 6 4.84 152 3.00 6 6.60 152 4.46 6 9.81 --- ----- ----- ----- ----- ----- ---


wrought 3d elbows MODELs

L90-3D 90° L30-3D 30°

L60-3D 60° L22-3D 22½°

L45-3D 45° L11-3D 11¼°

1. Long radius 90° elbows 3D, 5D, and 6D in

C606-04 and or ISO/FDIS 6182-12. For

sizes up to and including 4” are provided

dimensional tolerances of cast fittings,

with 4” (102 mm) long tangents, sizes 5” to 10” are provided with 1D long tangents

on request). 4. C to E tolerances: 2” through 6” ±1/8”

refer to ISO/FDIS 6182-12 Table 3..

(3.2mm); 8” through 16” ±1/4” (6.4mm);

• Plain-end or beveled end is also

and sizes 12” to 24” are provided with 12” (305mm) long tangents.

Catalog 2011

18” through 24” ±3/8” (9.5mm).

available upon request.

5. All weights are approximate, based on

3. Material: Standard wall steel pipe to ASTM

2. End Preparation: Roll-grooved to AWWA

calculated weight of pipe.

A53, Grade B. (Other materials available E C-

L60-3D

L90-3D Nominal Size mm / in 50 2 65 2½ 80 3 101.6mm 100 4 125 5 150 6 200 8 250 10 300 12 350 14 400 16 450 18 500 20 600 24

Pipe OD mm / in 60.3 2.375 73.0 2.875 88.9 3.500 101.6 4.000 114.3 4.500 141.3 5.563 168.3 6.625 219.1 8.625 273.1 10.750 323.9 12.750 355.6 14.000 406.4 16.000 457.2 18.000 508.0 20.000 609.6 24.000

L90-3D 90° Elbow C - E Weight mm / in Kgs / Lbs 254 2.5 10.0 5.51 292 4.5 11.5 9.92 330 6.63 13.0 14.62 368 8.4 14.5 18.6 406 10.18 16.0 22.44 508 18.39 20.0 40.54 610 27.52 24.0 60.67 813 60 32.0 132.28 1016 96 40.0 211.64 1219 145 48.0 319.67 1372 177 54.0 390.22 1524 248 60.0 546.75 1676 290.6 66.0 639.2 1829 282 72.0 621.7 2134 607 84.0 1338.2

C-E

C-E

R=3D

C-E

C-E

E C-

L60-3D 60° Elbow C - E Weight mm / in Kgs / Lbs 191 2.0 7.50 4.3 210 3.5 8.25 7.7 235 5.0 9.25 11.0 254 6.5 10.00 14.4 279 8.4 11.00 18.5 349 14.2 13.75 31.3 419 22.1 16.50 48.8 559 44.4 22.00 97.9 692 78.7 27.25 173.4 832 115.6 32.75 254.8 972 148.5 38.25 327.3 1111 194.6 43.75 429.0 1251 246.9 49.25 544.4 1391 305.5 54.75 673.5 1664 441.3 65.50 973.0

L45-3D L45-3D 45° Elbow C - E Weight mm / in Kgs / Lbs 165 1.7 6.50 3.75 184 3.0 7.25 6.7 197 4.6 7.75 10.14 216 5.6 8.50 12.0 229 6.69 9.00 14.75 286 12.18 11.25 26.85 343 18 13.50 39.68 457 39 18.00 85.98 572 62 22.50 136.69 686 93 27.00 205.03 800 103.1 31.50 227.3 914 159 36.00 350.54 1029 209.2 40.25 461.3 1143 258 45.00 568.79 1365 396 53.75 873.03

L30-3D L30-3D 30° Elbow C - E Weight mm / in Kgs / Lbs 146 1.5 5.75 3.4 152 2.6 6.00 5.8 165 3.6 6.50 8.0 171 4.6 6.75 10.2 184 5.8 7.25 12.8 229 9.9 9.00 21.8 273 15.4 10.75 3.9 368 30.8 14.50 68.0 457 54.7 18.00 120.5 552 80.3 21.75 177.0 641 103.1 25.25 227.3 737 135.1 29.00 297.9 826 171.5 32.50 378.1 914 212.2 36.00 467.8 1099 306.5 43.25 675.7

L22-3D L22-3D 22½° Elbow C - E Weight mm / in Kgs / Lbs 133 1.5 5.25 3.2 140 2.4 5.50 5.3 146 3.3 5.75 7.3 152 4.2 6.00 9.2 165 5.2 6.50 11.4 203 8.8 8.00 19.4 241 13.7 9.50 30.1 324 27.4 12.75 60.5 406 48.6 16.00 107.2 489 71.4 19.25 157.5 572 91.8 22.50 202.3 648 120.3 25.25 265.2 730 152.6 28.75 336.5 813 188.8 32.00 416.3 972 272.8 38.25 601.4

12” 3D 90° elbows ready for shipment



www.shurt.com

L11-3D L11-3D 11¼° Elbow C - E Weight mm / in Kgs / Lbs 114 1.3 4.50 2.8 121 2.1 4.75 4.6 127 2.8 5.00 6.2 127 3.4 5.00 7.6 133 4.2 5.25 9.3 165 7.2 6.50 15.8 197 11.2 7.75 24.6 267 22.4 10.50 49.3 330 39.6 13.00 87.3 394 58.2 15.50 128.3 464 74.8 18.25 164.8 527 98.0 20.75 216.0 593 124.3 23.35 274.1 660 153.9 26.00 339.2 787 222.3 31.00 490.0


L90-5D 90° L30-5D 30° Nominal Size mm / in 50 2 65 2½ 80 3 101.6mm 100 4 125 5 150 6 200 8 250 10 300 12 350 14 400 16 450 18 500 20 600 24

Pipe OD mm / in 60.3 2.375 73 2.875 88.9 3.500 101.6 4.000 114.3 4.500 141.3 5.563 168.3 6.625 219.1 8.625 273.1 10.750 323.9 12.750 355.6 14.000 406.4 16.000 457.2 18.000 508.0 20.000 609.6 24.000

L60-5D 60° L22-5D 22½°


L60-5D 60° Elbow C - E Weight mm / in Kgs / Lbs 248 2.5 9.75 5.6 286 4.6 11.25 10.2 324 6.8 12.75 15 311 9.1 12.25 20 394 11.8 15.5 26 495 20 19.5 44.1 591 31.1 23.25 68.6 787 62.5 31 137.7 991 110.7 39 244.1 1187 162.7 46.75 358.6 1384 209 54.5 460.7 1581 273.9 62.25 603.8 1778 347.5 70 766.2 1975 430 77.75 947.9 2369 621.1 93.25 1369.3


L90-6D 90° L30-6D 30° Nominal Size mm / in 50 2 65 2½ 80 3 101.6mm 100 4 125 5 150 6 200 8 250 10 300 12 350 14 400 16 450 18 500 20 600 24

Pipe OD mm / in 60.3 2.375 73 2.875 88.9 3.500 101.6 4.000 114.3 4.500 141.3 5.563 168.3 6.625 219.1 8.625 273.1 10.750 323.9 12.750 355.6 14.000 406.4 16.000 457.2 18.000 508.0 20.000 609.6 24.000

L60-6D 60° L22-6D 22½°


L60-6D 60° Elbow C - E Weight mm / in Kgs / Lbs 279 2.9 11 6.3 324 5.2 12.75 11.4 368 7.7 14.5 17 413 10.3 16.25 22.8 457 13.5 18 29.8 565 22.9 22.25 50.5 679 35.7 26.75 78.6 908 71.5 35.75 157.7 1137 126.7 44.75 279.4 1359 186.2 53.5 410.5 1588 239.2 62.5 527.3 1816 313.5 71.5 691.1 2045 397.8 80.5 877.1 2267 492.2 89.25 1085.1 2724 711 107.25 1567.5


Catalog 2011

L45-5D 45° L11-5D 11¼° L45-5D 45° Elbow C - E Weight mm / in Kgs / Lbs 210 2.2 8.25 4.8 235 3.9 9.25 8.6 260 5.7 10.25 12.5 286 7.5 11.25 16.5 318 9.7 12.5 21.3 394 16.4 15.5 36.1 470 25.5 18.5 56.2 622 51.2 24.5 112.8 781 90.7 30.75 199.9 940 133.2 37 293.7 1092 171.1 43 377.3 1251 224.3 49.25 494.5 1403 284.7 55.25 627.6 1562 352.2 61.5 776.4 1873 508.7 73.75 1121.6

L30-5D 30° Elbow C - E Weight mm / in Kgs / Lbs 171 1.8 6.75 4 191 3.2 7.5 7 203 4.5 8 10 222 5.9 8.75 13 241 7.5 9.5 16.6 298 12.7 11.75 28.1 356 19.9 14 43.8 476 39.9 18.75 87.9 597 70.7 23.5 155.8 711 103.8 28 228.9 832 133.4 32.75 294 953 174.8 37.5 385.3 1073 221.8 42.25 489 1187 274.4 46.75 605 1429 396.4 56.25 873.9

L22-5D 22½° Elbow C - E Weight mm / in Kgs / Lbs 152 1.6 6 3.6 165 2.8 6.5 6.2 178 4 7 8.8 191 5.1 7.5 11.3 203 6.5 8 14.3 254 10.9 10 24.1 305 17.1 12 37.6 406 34.2 16 75.4 508 60.6 20 133.7 610 89.1 24 196.4 711 114.4 28 252.3 813 150 32 330.7 914 190.4 36 419.7 1016 235.5 40 519.2 1219 340.2 48 750.1

L11-5D 11¼° Elbow C - E Weight mm / in Kgs / Lbs 127 1.4 5 3 133 2.3 5.25 5 140 3.1 5.5 6.9 146 3.9 5.75 8.7 152 4.9 6 10.7 191 8.3 7.5 18.2 229 12.8 9 28.3 305 25.8 12 56.8 381 45.6 15 100.6 457 67 18 147.8 533 86.1 21 189.8 610 112.9 24 248.8 686 143.2 27 315.7 762 177.2 30 390.6 908 256 35.75 564.3

L22-6D 22½° Elbow C - E Weight mm / in Kgs / Lbs 165 1.8 6.5 3.9 178 3 7 6.7 191 4.3 7.5 9.5 210 5.6 8.25 12.3 222 7.1 8.75 15.7 279 12 11 26.5 337 18.7 13.25 41.3 445 37.6 17.5 82.9 559 66.6 22 146.9 667 97.9 26.25 215.9 781 125.8 30.75 277.3 895 164.9 35.25 363.5 1003 209.2 39.5 461.3 1118 258.9 44 570.7 1329 373.9 52.34 824.4

L11-6D 11¼° Elbow C - E Weight mm / in Kgs / Lbs 133 1.5 5.25 3.2 140 2.4 5.5 5.3 146 3.3 5.75 7.3 152 4.2 6 9.2 165 5.2 6.5 11.4 203 8.8 8 19.4 241 13.7 9.5 30.1 324 27.4 12.75 60.5 406 48.6 16 107.2 483 71.4 19 157.5 565 91.8 22.25 202.3 648 120.3 25.5 265.2 730 152.6 28.75 336.5 806 188.8 31.75 416.3 972 272.8 38.25 601.4

L45-6D 45° L11-6D 11¼° L45-6D 45° Elbow C - E Weight mm / in Kgs / Lbs 229 2.4 9 5.3 260 4.3 10.25 9.5 38 6.4 1.5 14 324 8.4 12.75 18.6 356 10.9 14 24.1 445 18.6 17.5 40.9 533 28.9 21 63.7 711 58 28 127.8 889 102.7 35 226.4 1060 150.9 41.75 332.7 1238 193.8 48.75 427.3 1416 254.1 55.75 560.1 1594 322.4 62.75 710.7 1772 398.8 69.75 879.3 2127 576.2 83.75 1270.3

L30-6D 30° Elbow C - E Weight mm / in Kgs / Lbs 184 2 7.25 4.3 203 3.5 8 7.7 222 5 8.75 11 248 6.5 9.75 14.4 267 8.4 10.5 18.5 330 14.2 13 31.3 400 22.1 15.75 48.8 533 44.4 21 97.9 660 78.7 26 173.4 794 115.6 31.25 254.8 927 148.5 36.5 327.3 1060 194.6 41.75 429 1194 246.9 47 544.4 1327 305.5 52.25 673.5 1588 441.3 62.5 973

www.shurt.com


EXTRA HEAVY CUT GROOVEd FITTINGS "EP" (End Protection) MODEL

10EP 90° EP ELBOW 11EP 45° EP ELBOW

Catalog 2011

20EP EP Tee 35EP EP cross

Shurt offers a variety of fittings with

be used with XH-70EP couplings in high

extra heavy (Sch. 80) wall thickness and

pressure systems where the system

"EP" cut grooves available for use with

pressure exceeds the published ratings for

XH-70EP couplings. These fittings must

XH-1000 or Model 7707 couplings.

C-E

C-E

C-E

C-E

#10EP

Nominal Size mm / in 50 2 65 2½ 80 3 100 4 150 6

Pipe O. D. mm / in 60.3 2.375 73.0 2.875 88.9 3.500 114.3 4.500 168.3 6.625

#10EP 90° Elbows C - E Weight mm / in Kgs / Lbs 83 1.0 3.25 2.2 95 1.7 3.75 3.8 108 2.7 4.25 5.9 127 4.4 5.00 9.7 165 10.4 6.50 22.9

#11EP 45° Elbows C - E Weight mm / in Kgs / Lbs 51 0.8 2.00 1.8 57 1.3 2.25 2.9 64 1.9 2.50 4.3 76 3.9 3.00 8.5 89 7.5 3.50 16.5

C-E

C-E

C-E C-E #20EP #11EP #35EP

C - E mm / in 83 3.25 95 3.75 108 4.25 127 5.00 165 6.50

#20EP Tee Weight Kgs / Lbs 1.6 3.5 3.6 7.9 7.3 16.0 10.7 23.5 12.2 27.0

#35EP Cross C - E Weight mm / in Kgs / Lbs 83 1.8 3.25 3.9 95 3.0 3.75 6.6 108 6.4 4.25 14.2 127 7.2 5.00 15.8 165 20.9 6.50 46.0

For "EP cut-grooves, see page 26.

MODEL

22EP HEADER TEE Shurt Model 22EP Header Tees are

C-E

specifically designed for use in oilfield production headers where the top (test) line is 2" (50mm) and the bottom production line

C-E

is 3" (80mm) or 4" (100mm). #22EP




750 psi @100°F 52 Bar @38°C


Class 300




Fitting Size Mated C to E Nominal Size Pipe O. D. mm / in mm / in 50 to 80 60.3 2 to 3 2.375 50 to 100 73.0 2 to 4 2.875

C - E mm / in 108 4.25 127 5.00

#22EP Header Tee

www.shurt.com

Weight Kgs / Lbs 1.5 3.4 1.9 4.1

Section 3 Stainless Steel Series Shurt Stainless Steel Piping Series.................................... 60 Grooved Mechanical Couplings SS-5 Rigid Coupling........................................................................... 61 SS-7 Rigid Coupling........................................................................... 62 SS-7X Rigid Coupling........................................................................ 63 SS-8 Flexible Coupling....................................................................... 64 SS-8X Heavy Duty Flexible Coupling................................................. 65 SS-1200 High Pressure Flexible Coupling........................................ 66

SS-28 Hinged Lever Coupling............................................................ 67 Cast Grooved Fittings SS-10 / SS-11 / SS-20 / SS-60 Elbows, Tee, Cap........................ 68 SS-21 / SS–50 Reducing Tee, Concentric Reducer......................... 69 Wrought Grooved Fittings WS-10 / WS-10L / WS-11 / WS-20 / WS -60 / WS-21 / WS-50 Elbows, Tee, Cap, Reducing Tee & Concentric Reducer....................70

Flange Adapters SS-41 / SS-80 Flange Adapters....................................................... 71 Mechanical Tee, Y-Strainer & Valves SS-723 / SS-726 Mechanical Tee, Y Strainer.................................. 72 SJ-600L / SJ-600W Ball Valves..................................................... 73 SJ-400-L / SJ-400-W Butterfly Valve............................................. 74


Catalog 2011

www.shurt.com

Catalog 2011

Stainless Steel Series Shurt offers a full range of stainless steel grooved mechanical couplings in CF8 (304) and CF8M (316) for general service applications and in specialty alloys for applications including reverse osmosis and desalination systems. Grooved fittings are available in sizes from 1” (25 mm) to 24” (600 mm) produced in a combination of investment castings and wrought stainless. The design pressure rating of Shurt stainless steel grooved couplings follows Class 150 and is based on roll grooved Sch. 40S pipe. Pressure ratings will vary depending on the type of pipe used and grooves processed. For example; for cut grooved Sch. 40S pipe - apply 110%, for roll grooved Sch.10S pipe - apply 80% and for rollgrooved Sch. 5S pipe - apply 50%. Shurt Model SS-1200 and

Model SS-8X are designed for high pressure applications for use with cut-grooved Sch. 40S and or Sch. 80S pipe with pressures expressed in CWP. Shurt ductile iron couplings can be used in conjunction with stainless steel pipe, depending on the application, as the flow media does not come in direct with coupling housings but rather only the gasket. See page 39 for performance data.

Groove corners are not defined

Stainless steel pipe in general is more difficult to groove than carbon steel pipe, as it is more difficult to achieve defined groove corners on stainless pipe. Grooves that are not defined and have too much of a radius could result in t failure. Care must be taken to process

OK

grooves as defined as possible. For this reason, roll-groove machine manufacturers offer a variety of roll sets depending on the pipe material and wall thickness being grooved. Always select the correct roll set for the pipe being grooved.

If the same roll-set that has been used for carbon steel pipe is used on stainless steel pipe, rust or scale may be transferred to the stainless steel pipe during processing of the groove. Thus we recommend the use of a separate roll set specifically for use with stainless steel pipe. Also use caution to keep roll grooved stainless steel pipe dry prior to installation.

Stainless Steel Casting Specifications

Austenitic Stainless Steel

Duplex (Austenitic / Ferritic) Stainless Steel

Grade

CF8

CF8M

CK3MCuN

2A, CE8MN

4A, CD3MN

5A, CE3MN

(UNS)

J92600

J92900

J93254

J93345

J92205

J93404

Composition, % (max, except where range is given) Carbon

0.08

0.08

0.025

0.08

0.03

Manganese

1.50

1.50

1.20

1.00

1.50

0.03 1.50

Silicon

2.00

1.50

1.00

1.50

1.00

1.00 0.040

Sulfur

0.040

0.040

0.010

0.040

0.020

Phosphorus

0.040

0.040

0.045

0.040

0.040

0.040

Chromium

18.0-21.0

18.0-21.0

19.5-20.5

22.5-25.5

21.0-23.5

24.0-26.0

Nickel

8.0-11.0

9.0-12.0

17.5-19.5

8.0-11.0

4.5-6.5

6.0-8.0

Molybdenum

0.50

2.0-3.0

6.0-7.0

3.0-4.5

2.5-3.5

4.0-5.0

0.10-0.30

0.10-0.30

0.10-0.30

Nitrogen

0.18-0.24

Copper

0.50-1.00

1.00

Tensile Requirements, min.

Tensile Strength, ksi (MPa)

70 (485)

70 (485)

80 (550)

95 (655)

90 (620)

100 (690)

Yield Strength, ksi (MPa)

30 (205)

30 (205)

38 (260)

65 (450)

60 (415)

75 (515)

Elongation, %

35

30

35

25

25

18

ASTM Standards

A351/ A743/A744

A351/A743/A744

A351/A743/A744

A890/A351

A890

A890

Wrought Equivalent Grade

304

316

254SMO*

45D*

2205

SAF 2507*

* 254SMO is a ed trademark of AvestaPolarit AB, 45D is a ed trademark of ESCO Corporation and SAF 2507 is a ed trademark of AB Sandvik Steel.



www.shurt.com

Catalog 2011

MODEL

SS-5

RIGID COUPLING

- Angle-Pad Design The Shurt Model SS-5 is an angle-pad

bolt you can make a fast and easy "swing-

design stainless steel coupling for use with

over” installation. The SS-5 couplings are

Sch. 5S, Sch. 10S or Sch. 40S stainless

comprised of two identical CF8 (304) or

steel pipe where a rigid connection is

CF8M (316) housing segments, EPDM

desired. The angle-pad design allows the

gaskets and stainless steel track bolts and

coupling housings to slide along the bolt

heavy duty nuts.

The Shurt Model SS-5 is available with

pads when tightened. The result is an offset clamping action which provides a rigid t

a standard “C” shaped or GapSeal ® gasket

which resists so called ‘snaking’ of a long

in a variety of grades to meet your specific

straight run. With the removal of only one

service requirements.


Working Pressure (STD, Roll-Grooved)


300 psi @100°F 20 Bar @38°C


*The working pressure shown is based on roll-grooved Sch. 40S pipe. Apply 110% for cut-grooved Sch. 40S pipe. Apply 80% for roll-grooved Sch. 10S pipe and 50% for roll-grooved Sch. 5S pipe. *Proof test pressure: 1.5 times the working pressure, non-shock cold water. *Burst pressure is engineered minimum 3 times the working pressure.

Nominal Size mm / in 32 1¼ 40 1½ 50 2 65 2½ 76.1mm 80 3 100 4 139.7mm 125 5 165.1mm 150 6 200 8 200 JIS

Pipe O. D. mm / in 42.2 1.660 48.3 1.900 60.3 2.375 73.0 2.875 76.1 3.000 88.9 3.500 114.3 4.500 139.7 5.500 141.3 5.563 165.1 6.500 168.3 6.625 219.1 8.625 216.3 8.516

Max. Working Pressure Bar/PSI 20 300 20 300 20 300 20 300 20 300 20 300 20 300 20 300 20 300 20 300 20 300 20 300 20 300

Max. End Load kN / Lbs 2.80 650 3.66 850 5.71 1330 8.37 1950 9.09 2120 12.41 2080 20.51 4770 30.64 7120 31.35 7290 42.80 9950 44.47 10340 75.37 17520 73.45 17080


Axial Displacement A mm / in mm / in 0 ~ 1.2 66 0 ~ 0.05 2.60 0 ~ 1.2 72 0 ~ 0.05 2.83 0 ~ 1.7 85 0 ~ 0.07 3.35 0 ~ 1.7 98 0 ~ 0.07 3.86 0 ~ 1.7 100 0 ~ 0.07 3.94 0 ~ 1.7 113 0 ~ 0.07 4.45 0 ~ 4.1 146 0 ~ 0.16 5.75 0 ~ 4.1 173 0 ~ 0.16 6.81 0 ~ 4.1 175 0 ~ 0.16 6.89 0 ~ 4.1 200 0 ~ 0.16 7.87 0 ~ 4.1 203 0 ~ 0.16 8.00 0 ~ 4.8 264 0 ~ 0.19 10.40 0 ~ 4.8 260 0 ~ 0.19 10.24

Dimensions B mm / in 102 4.00 109 4.29 117 4.61 132 5.20 136 5.35 148 5.83 182 7.17 227 8.94 229 9.02 246 9.69 249 9.80 330 12.99 340 13.39

Bolts Size C mm / in No. mm / in 46 M10 x 55 2 1.81 ⅜ x 2⅛ 46 M10 x 55 2 1.81 ⅜ x 2⅛ 47 M10 x 70 2 1.85 ⅜ x 2¾ 47 M10 x 70 2 1.85 ⅜ x 2¾ 47 M10 x 70 2 1.85 ⅜ x 2¾ 48 M10 x 70 2 1.88 ⅜ x 2¾ 53 M10 x 70 2 2.09 ⅜ x 2¾ 53 M12 x 75 2 2.09 ½ x 3 53 M12 x 75 2 2.09 ½ x 3 54 M12 x 75 2 2.13 ½ x 3 54 M12 x 75 2 2.13 ½ x 3 64 M16 x 135 2 2.52 ⅝ x 5 5/16 64 M20 x 120 2 2.50 ¾ x 4¾

www.shurt.com

Weight Kgs / Lbs 0.6 1.4 0.7 1.5 0.8 1.7 0.9 2.1 1.0 2.2 1.2 2.6 1.9 4.1 2.6 5.7 2.6 5.7 3.1 6.8 3.1 6.8 6.1 13.4 7.4 16.2


Catalog 2011

MODEL

SS-7 STAINLESS STEEL

Rigid Coupling

The Model SS-7 is a tongue and groove rigid

(316) with 304 and 316 bolts and nuts.

coupling designed for a variety of moderate

SS-7 couplings should always be installed

service pressure applications. The SS-7 is

so that the coupling bolt pads make metal to

supplied standard in CF8 (304) and CF8M

metal .


Working Pressure (S40S, Roll-grooved)


300 psi @100°F 20 Bar @38°C


• The working pressure shown is based on roll-grooved Sch. 40S pipe. Apply 110% for cut-grooved Sch. 40S pipe. Apply 80% for roll-grooved Sch. 10S pipe and 50% for roll-grooved Sch. 5S pipe. • Proof test pressure: 1.5 times the working pressure, non-shock cold water. • Burst pressure is engineered minimum 3 times the working pressure.

Nominal Size mm / in 32 1¼ 40 1½ 50 2 65 2½ 76.1 mm 80 3 100 4 139.7 mm 125 5 165.1 mm 150 6 200 8 200 JIS

Pipe O. D. mm / in 42.2 1.660 48.3 1.900 60.3 2.375 73.0 2.875 76.1 3.000 88.9 3.500 114.3 4.500 139.7 5.500 141.3 5.563 165.1 6.500 168.3 6.625 219.1 8.625 216.3 8.516

C

B

A

Pipe End Separation A mm / in mm / in 0-1.6 68 0-0.06 2.68 0-1.6 74 0-0.06 2.91 0-1.6 86 0-0.06 3.39 0-1.6 100 0-0.06 3.94 0-1.6 100 0-0.06 3.94 0-1.6 112 0-0.06 4.41 0-3.2 143 0-0.13 5.63 0-3.2 172 0-0.13 6.77 0-3.2 171 0-0.13 6.73 0-3.2 195 0-0.13 7.68 0-3.2 201 0-0.13 7.91 0-3.2 264 0-0.13 10.39 0-3.2 257 0-0.13 10.12

Dimensions Bolt B C Size Weight mm / in mm / in in Kgs / Lbs 105 45 0.7 ⅜x2 4.13 1.75 1.5 108 46 0.8 ⅜x2 4.25 1.81 1.8 125 46 0.9 ⅜x2 4.92 1.81 2.0 138 46 0.8 ⅜x2 5.43 1.81 1.8 143 46 1.0 ⅜x2 5.63 1.81 2.2 160 46 1.2 ⅜x2 6.30 1.81 2.6 207 51 2.1 ½x3 8.15 2.00 4.6 231 51 2.8 ½x3 9.09 2.00 6.2 236 51 2.7 ½x3 9.29 2.00 5.9 255 53 3.1 ½x3 10.04 2.09 6.8 256 51 3.1 ½x3 10.08 2.00 6.8 333 62 6.4 ⅝ x 3½ 13.11 2.44 14.1 346 62 6.0 ⅝ x 3½ 13.62 2.44 13.2

The tongue and groove style rigid coupling may allow for rotation when installed on undersized grooves.

Domestic Water Service



www.shurt.com

Catalog 2011

MODEL

SS-7X STAINLESS STEEL

Rigid Coupling

The Model SS-7X is a tongue and groove

in CF8 (304) and CF8M (316) with 304

rigid coupling designed to provide a rigid

and 316 bolts and nuts. The bolts must be

t for stainless steel pipe in sizes 10”

fastened to the required torque for proper

through 24”. The SS-7X is supplied standard

installation.




300 psi @100°F 20 Bar @38°C



B

C

B

A

10" ~ 14"

Nominal Size mm / in 250 10 300 12 250 JIS 300 JIS 350 14 400 16 450 18 500 20 550 22 600 24

Pipe O. D. mm / in 273.0 10.750 323.9 12.750 267.4 10.528 318.5 12.539 355.6 14.000 406.4 16.000 457.2 18.000 508.0 20.000 558.8 22.000 609.6 24.000

Pipe End Separation mm / in 0-3.2 0-0.13 0-3.2 0-0.13 0-3.2 0-0.13 0-3.2 0-0.13 0-3.2 0-0.13 0-3.2 0-0.13 0-3.2 0-0.13 0-3.2 0-0.13 0-3.2 0-0.13 0-3.2 0-0.13

A mm / in 318 12.52 374 14.72 316 12.44 370 14.57 397 15.63 461 18.15 514 20.24 571 22.48 622 24.49 673 26.47

C

C

B

A

A

16" ~ 18"

20" ~ 24"

Dimensions Bolt B C Size mm / in mm / in No. in 406 65 2 ⅞ x 6½ 15.98 2.56 452 65 2 ⅞ x 6½ 17.78 2.56 425 64 2 ⅞ x 6½ 16.73 2.52 465 64 2 ⅞ x 6½ 18.31 2.52 500 75 2 ⅞ x 6½ 19.69 2.95 536 75 6 ⅞ x 3½ 21.10 2.95 587 75 6 ⅞ x 3½ 23.11 2.95 669 79 8 ¾ x 4¾ 26.34 3.11 720 79 8 ¾ x 4¾ 28.35 3.11 771 79 8 ¾ x 4¾ 30.35 3.11

Bolt Torque N-m / Lbs-Ft 145 – 235 105 - 175 145 – 235 105 - 175 145 – 235 105 - 175 145 – 235 105 - 175 145 – 235 105 - 175 68 - 100 50 - 75 68 - 100 50 - 75 85 – 200 65 - 150 85 – 200 65 - 150 85 – 200 65 - 150

Weight Kgs / Lbs 10.5 23.1 11.5 23.3 8.5 18.7 9.8 21.6 15.0 33.0 19.4 42.7 25.0 55.0 33.1 72.8 33.0 72.6 34.7 76.3

Air Conditioning


www.shurt.com


Catalog 2011

MODEL


Flexible Coupling

The Model SS-8 is a flexible coupling

(316) with 304 or 316 bolts and nuts. SS-8

designed for a variety of general service

couplings should always be installed so that

and specialty applications. The SS-8 is

the coupling bolt pads make metal to metal

supplied standard in CF8 (304) and CF8M

.




300 psi @100°F 20 Bar @38°C



Nominal Size mm / in 25 1 32 1¼ 40 1½ 50 2 65 2½ 76.1mm 80 3 100 4 139.7mm 125 5 165.1mm 150 6 200 8 200 JIS


Pipe O. D. mm / in 33.4 1.315 42.2 1.660 48.3 1.900 60.3 2.375 73.0 2.875 76.1 3.000 88.9 3.500 114.3 4.500 139.7 5.500 141.3 5.563 165.1 6.500 168.3 6.625 219.1 8.625 216.3 8.516

Pipe End Separation A mm / in mm / in 0 - 1.6 55.7 0 - 0.06 2.19 0 - 1.6 64.6 0 - 0.06 2.54 0 - 1.6 70.8 0 - 0.06 2.79 0 - 1.6 83.0 0 - 0.06 3.28 0 - 1.6 96.2 0 - 0.06 3.79 0 - 1.6 99.0 0 - 0.06 3.91 0 - 1.6 111.0 0 - 0.06 4.39 0 - 3.2 143.0 0 - 0.13 5.62 0 - 3.2 171.0 0 - 0.13 6.73 0 - 3.2 170.8 0 - 0.13 6.72 0 - 3.2 194.0 0 - 0.13 7.67 0 - 3.2 198.0 0 - 0.13 7.80 0 - 3.2 255.0 0 - 0.13 10.04 0 - 3.2 251.0 0 - 0.13 10.00


B

C

A

Dimensions Deflection Bolt B C Degree Size Weight mm / in mm / in ( ° ) in Kgs / Lbs 87.5 44.0 0.5 5/16 x1½ 2° - 45’ 3.45 1.73 1.1 97.8 44.0 0.5 5/16 x1½ 2° - 10’ 3.85 1.73 1.1 105.1 44.0 0.5 5/16 x1½ 1° - 54’ 4.14 1.73 1.1 124.0 44.0 0.7 1° - 31’ ⅜x2 4.88 1.73 1.5 139.9 44.0 0.8 1° - 15’ ⅜x2 5.51 1.73 1.8 145.0 44.0 0.8 1° - 12’ ⅜x2 5.71 1.73 1.8 157.0 44.0 1.0 1° - 02’ ⅜x2 6.18 1.73 2.2 200.0 50.0 1.7 1° - 36’ ½x3 7.87 1.97 3.7 231.0 50.0 2.2 1° - 18’ ½x3 9.09 1.97 4.8 226.1 50.0 2.2 1° - 18’ ½x3 8.90 1.97 4.8 253.0 53.0 2.7 1° - 07’ ½x3 9.96 2.09 5.9 253.1 53.0 2.9 1° - 05’ ½x3 9.96 2.09 6.4 337.0 62.0 6.4 0° - 50’ ⅝ x 3½ 13.27 2.44 14.1 346.0 60.0 5.1 0° - 51’ ⅝ x 3½ 13.62 2.40 11.3

www.shurt.com

Catalog 2011

MODEL

SS-8X Stainless Steel

Heavy Duty Flexible Coupling The Model SS-8X is designed for high

(254SMO*). The SS-8X features 316 bolts,

pressure applications including reverse

washers and Silicon Bronze nuts to help

osmosis and desalination systems. The

prevent galling during repetitive use.

SS-8X is available in Duplex CD3MN

The SS-8X is also available in CF8M (316)

(2205), Super Duplex CE8MN, CE3MN

with 316 bolts and nuts. Shurt

(2507) and 6-Moly stainless steel CK3MCuN

for details.

Pressure-Temperature Rating Size Nom. Rating

Working Pressure (S40S, Cut-grooved)

Test Pressure (Hydrostatic)

3/4” – 4”

1400 psi @100°F

2100 psi

98 Bar @38°C

147 Bar

EPDM: 230°F / 110°C

5” – 8”

1000 psi @100°F

1500 psi


70 Bar @38°C

10.5 MPa

CWP 20 - 100

CWP 125 - 200


B

C

A

*Working pressure is based on cut-grooved Sch. 40S or 80S pipe only. *Burst pressure is engineered minimum 2 times the working pressure.s

Nominal Size mm / in 20 ¾ 25 1 32 1¼ 40 1½ 50 2 65 2½ 80 3 100 4 125 5 150 6 200 8 200 JIS

Pipe O. D. mm / in 26.7 1.050 33.4 1.315 42.2 1.660 48.3 1.900 60.3 2.375 73.0 2.875 88.9 3.500 114.3 4.500 141.3 5.563 168.3 6.625 219.1 8.625 216.3 8.516

Pipe End Separation A mm / in mm / in 0 - 1.6 56.0 0 - 0.06 2.20 0 - 1.6 63.0 0 - 0.06 2.45 0 - 1.6 72.0 0 - 0.06 2.82 0 - 1.6 78.0 0 - 0.06 3.06 0 - 1.6 88.0 0 - 0.06 3.46 0 - 1.6 153.0 0 - 0.06 6.02 0 - 1.6 120.0 0 - 0.06 4.71 0 - 3.2 152.0 0 - 0.13 5.98 0 - 3.2 181.0 0 - 0.13 7.13 0 - 3.2 208.0 0 - 0.13 8.19 0 - 3.2 267.0 0 - 0.13 10.53 0 - 3.2 264.0 0 - 0.13 10.39

Dimensions Deflection Bolt B C Degree Size Weight mm / in mm / in ( ° ) in Kgs / Lbs 95.0 46.0 0.7 3° - 23’ ⅜ x 2 3.75 1.81 1.5 99.0 46.0 0.8 2° - 45’ ⅜ x 2 3.91 1.81 1.8 111.0 46.0 0.9 2° - 10’ ⅜ x 2 4.37 1.81 2.0 123.0 46.0 1.0 1° - 54’ ⅜ x 2 4.82 1.81 2.2 134.0 47.0 1.2 1° - 31’ ⅜ x 2 5.28 1.85 2.6 103.0 47.0 1.3 1° - 15’ ⅜ x 2 4.06 1.85 2.9 171.0 47.0 1.8 1° - 02’ ½x3 6.74 1.85 4.0 201.0 52.0 2.4 1° - 36’ ½x3 7.90 2.03 5.3 249.0 53.0 3.5 1° - 18’ ⅝ x 3½ 9.80 2.09 7.7 276.0 53.0 4.0 1° - 05’ ⅝ x 3½ 10.85 2.09 8.8 341.0 62.0 6.8 0° - 50’ ¾ x 4¾ 13.43 2.44 15.0 338.0 62.0 6.5 0° - 51’ ¾ x 4¾ 13.31 2.44 14.3

Working pressure ratings are based upon generally accepted pressure piping design standards and testing in accordance with ASME Section VIII Division 1 pressure vessel test methods.

Reverse osmosis plant


www.shurt.com


Catalog 2011

MODEL

SS-1200 Stainless Steel

High Pressure Flexible Coupling The Model SS-1200 is designed for high

(2205), Super Duplex CE8MN, CE3MN

pressure applications including reverse

(2507) and 6-Moly stainless steel CK3MCuN

osmosis, desalination and other specialty

(254SMO*). The SS-1200 features 316

systems. The SS-1200 is available in strong

bolts, washers and Silicon Bronze nuts to

and anti-corrosive alloys of Duplex CD3MN

help prevent galling during repetitive use.

B

Pressure-Temperature Rating Nom. Rating CWP

Working Pressure (S40S, Cut- or Roll-grooved)

Test Pressure (Hydrostatic)


1200 psi @100°F 84 Bar @38°C

1800 psi 126 Bar


C

A

*Working pressure is based on cut-grooved Sch. 40S or 80S pipe only. *Burst pressure is engineered minimum 2 times the working pressure.

Nominal Size mm / in 20 ¾ 25 1 32 1¼ 40 1½ 50 2 65 2½ 80 3 100 4

Pipe O. D. mm / in 26.7 1.050 33.4 1.315 42.2 1.660 48.3 1.900 60.3 2.375 73.0 2.875 88.9 3.500 114.3 4.500

Pipe End Separation mm / in 0 - 1.6 0 - 0.06 0 - 1.6 0 - 0.06 0 - 1.6 0 - 0.06 0 - 1.6 0 - 0.06 0 - 1.6 0 - 0.06 0 - 1.6 0 - 0.06 0 - 1.6 0 - 0.06 0 - 3.2 0 - 0.13

A mm / in 53 2.09 60 2.36 70 2.76 76 2.99 88 3.46 102 4.02 119 4.69 152 5.98

Dimensions Deflection Bolt Size B C Degree mm / in mm / in ( ° ) No. in 94 46 3° - 23’ 2 ⅜x2 3.70 1.81 101 46 2° - 45’ 2 ⅜x2 3.98 1.81 111 46 2° - 10’ 2 ⅜x2 4.37 1.81 117 46 1° - 54’ 2 ⅜x2 4.61 1.81 137 49 1° - 31’ 2 ½x3 5.39 1.85 151 49 1° - 15’ 2 ½x3 5.94 1.85 168 49 1° - 02’ 2 ½x3 6.61 1.85 207 52 1° - 36’ 2 ⅝ x 3½ 8.15 2.03

Weight Kgs / Lbs 0.45 0.99 0.55 1.21 0.63 1.39 0.70 1.54 1.04 2.29 1.38 3.04 1.55 3.41 2.13 4.69

Working pressure ratings are based upon generally accepted pressure piping design standards and testing in accordance with ASME Section VIII Division 1 pressure vessel test methods.

The Shurt Fast-Fit gasket has been

with ANSI/NSF 61 for potable water (Cold

designed and engineered for easier and

Water +86°F / 30°C and Hot Water +180°F

faster installations. The pipe-end friendly

/ +82°C).

design eliminates struggling to stretch the gasket over the pipe ends and the Fast-Fit

Always use the factory supplied Shurt

gasket also features Shurt’s Gap-Seal

Fast-Fit gasket. Performance standards do

technology, which seals the gap between

not the use of a standard gasket in

the pipe ends and eliminates stagnant water

the SS-1200 coupling.

pockets within the gasket cavity. The FastFit gasket is UL classified in accordance

* 254SMO is a ed trademark of AvestaPolarit AB.



Fast-Fit Gasket: Easy installation with a single hand

Always use the Shurt Fast-fit gasket. Don't use a standard gasket with the SS1200 coupling.

www.shurt.com

Catalog 2011

MODEL

SS-28 Stainless Steel HINGED LEVER COUPLING The Model SS-28 Hinged Grooved

grooved pipe. Housings 40mm - 100mm

Coupling is designed for quick connect and

(1½”- 4”) feature a smooth outer surface,

disconnect services. The housing segments

housings 125mm - 300mm (5” - 12”) feature

are hinged with a lever handle for easy

a cross-ribbed design for added strength.

assembly. Use of the split pin can prevent

Standard gasket: Grade “E” EPDM or Grade

the accidental opening of the coupling. The

“T” Nitrile.

Model SS-28 can be used in a wide variety

Available standard in CF8 (304) or CF8M

of applications with standard roll- or cut-

(316).


B

Working Pressure (STD, Roll-Grooved)


300 psi @100°F 20 Bar @38°C


*The working pressure shown is based on roll-grooved Sch. 40S pipe. Apply 110% for cut-grooved Sch. 40S pipe. Apply 80% for roll-grooved Sch. 10S pipe and 50% for roll-grooved Sch. 5S pipe. *Proof test pressure: 1.5 times the working pressure, non-shock cold water. *Burst pressure is engineered minimum 3 times the working pressure.

Nominal Size mm / in 40 1½ 50 2 65 2½ 76.1mm 80 3 100 4 125 5 125 5 165.1mm 150 6

Pipe O. D. mm / in 48.3 1.900 60.3 2.375 73.0 2.875 76.1 3.000 88.9 3.500 114.3 4.500 139.7 5.500 141.3 5.563 165.1 6.500 168.3 6.625

Max. Working Pressure Bar / PSI 20 300 20 300 20 300 20 300 20 300 20 300 20 300 20 300 20 300 20 300

Axial Displacement A mm / in mm / in 0 – 1.6 75 0 – 0.06 2.95 0 – 1.6 86 0 – 0.06 3.39 0 – 1.6 92 0 – 0.06 3.62 0 – 1.6 92 0 – 0.06 3.62 0 – 1.6 119 0 – 0.06 4.69 0 – 3.2 165 0 – 0.13 6.50 0 – 3.2 189 0 – 0.13 7.44 0 – 3.2 189 0 – 0.13 7.44 0 – 3.2 213 0 – 0.13 8.39 0 – 3.2 216 0 – 0.13 8.50

A

C

split pin

Dimensions B mm / in 118 4.65 121 4.76 150 5.91 150 5.91 163 6.42 205 8.07 253 9.96 253 9.96 278 10.94 281 11.06

Deflection C Degree Weight mm / in ( ° ) Kgs / Lbs 47 1.0 3º - 48' 1.85 2.2 48 1.1 3º - 31' 1.89 2.4 48 1.4 2º - 30' 1.89 3.1 48 1.4 2º - 24' 1.89 3.1 48 1.8 2º - 24' 1.89 4.0 52 2.7 3º - 12' 2.05 5.9 52 4.9 2º - 37' 2.05 10.8 52 4.9 2º - 36' 2.05 10.8 52 5.8 2º - 14' 2.05 12.8 52 5.8 2º - 10' 2.05 12.8

*Deflection or angular movement is the maximum value that a coupling allows under no internal pressure.

Expansion Pipe

Lever handles are factory assembled tight for safety. The use of an expansion pipe will aid the easy opening and closing. Expansion pipes are available upon request.


www.shurt.com


CAST GROOVED FITTINGS MODEL

Catalog 2011

MODEL

SS-10 90° ELBOW SS-11 45° ELBOW

SS-20 SS-60

The Shurt Model SS-10, SS-11,

and CF8M (316). In addition fittings are

service requirements. All cast fittings feature full flow

TEE CAP

SS-20 and SS-60 stainless steel grooved

also available on request in CF3M (316L),

fittings are investment cast in sizes 1" -

316Ti, 2205 Duplex, 2507 Super Duplex and

characteristics and are designed to the

12". These fittings are supplied in ASTM

ASTM CK-3MCuN (UNS J93245) the cast

same C - E dimensions of standard ductile

A351 or A743 austenitic grades CF8 (304)

equivalent to 254SMO* to meet your specific

iron grooved fittings.

Pressure-Temperature Rating Working Pressure Size Nom. Rating (STD, Roll-grooved) 1” - 4“ Class 300 25 - 100 5” – 12” Class 250 125 - 300




-E

C-E

C

C-E

E-E E-E

C-E

Nominal Size mm / in 25 1 32 1¼ 40 1½ 50 2 65 2½ 76.1 mm 80 3 100 4 139.7 mm 125 5 165.1 mm 150 6 200 8 250 10 300 12 200 JIS 250 JIS 300 JIS

Pipe O. D. mm / in 33.4 1.315 42.2 1.660 48.3 1.900 60.3 2.375 73.0 2.875 76.1 3.000 88.9 3.500 114.3 4.500 139.7 5.500 141.3 5.563 165.1 6.500 168.3 6.625 219.1 8.625 273.0 10.750 323.9 12.750 216.3 8.516 267.4 10.528 318.5 12.539

SS-10 90° Elbow C - E Weight mm / in Kgs / Lbs 57 0.3 2.25 0.7 70 0.4 2.75 0.9 70 0.4 2.75 0.9 83 0.6 3.25 1.3 95 1.4 3.75 3.1 95 1.6 3.75 3.5 108 1.3 4.25 2.9 127 2.2 5.00 4.8 140 3.9 5.50 8.6 140 3.9 5.50 8.6 165 6.2 6.50 13.6 165 6.5 6.50 14.3 197 10.7 7.75 23.5 229 29.0 9.00 63.8 254 38.0 10.00 83.6 197 10.7 7.75 23.5 238 29.0 9.37 63.8 310 21.7 12.20 47.7

SS-11 45° Elbow C - E Weight mm / in Kgs / Lbs 45 0.2 1.75 0.4 45 0.3 1.75 0.7 45 0.4 1.75 0.9 51 0.5 2.00 1.1 57 1.0 2.25 2.2 57 1.0 2.25 2.2 64 1.0 2.50 2.2 76 1.6 3.00 3.5 83 2.8 3.25 6.2 83 2.9 3.25 6.4 89 4.1 3.50 9.0 89 4.2 3.50 9.2 108 7.1 4.25 15.6 121 16.8 4.75 37.0 133 19.6 5.25 43.1 108 7.1 4.25 15.6 121 16.8 4.75 37.0 133 19.6 5.25 43.1

SS-20 Tee C - E Weight mm / in Kgs / Lbs 57 0.4 2.25 0.9 70 0.7 2.75 1.5 70 0.8 2.75 1.8 83 1.1 3.25 2.4 95 2.5 3.75 5.5 95 2.5 3.75 5.5 108 2.1 4.25 4.6 127 3.4 5.00 7.5 140 5.6 5.50 12.3 140 5.8 5.50 12.8 165 9.0 6.50 19.8 165 9.7 6.50 21.3 197 18.8 7.75 41.4 229 21.1 9.00 46.4 254 43.0 10.00 94.6 197 13.8 7.75 30.4 229 19.8 9.00 43.6 254 27.1 10.00 59.6

*254SMO is a ed trademark of Avesta Polarit AB.



www.shurt.com

SS-60 Cap E - E mm / in 24 0.94 24 0.94 24 0.94 24 0.94 45 1.75 45 1.75 51 2.00 51 2.00 60 2.38 60 2.38 76 3.00 76 3.00 90 3.50 127 5.00 145 5.71 90 3.50 127 5.00 145 5.71

Weight Kgs / Lbs 0.1 0.2 0.1 0.2 0.2 0.4 0.2 0.4 0.4 0.9 0.4 0.9 0.7 1.5 0.9 2.0 1.6 3.5 1.5 3.3 2.6 5.7 2.4 5.3 5.2 11.4 10.2 22.4 14.7 32.3 5.2 11.4 8.9 19.6 14.7 32.3

MODEL

SS-21 REDUCING TEE

Catalog 2011

MODEL

SS-50 CONCENTRIC REDUCER

The Shurt Model SS-21 and SS-50 stainless steel fittings are investment cast in sizes to 8" and sand cast or wrought in sizes 10"-24".

C-E

C-B

Nominal Size mm / in 40 x 25 1½x 1 40 x 32 1½ x 1¼ 50 x 25 2 x 1 50 x 32 2 x 1¼ 50 x 40 2 x 1½ 65 x 25 2½ x 1 65 x 32 2½ x 1½ 65 x 40 2½x 1½ 65 x 50 2½ x 2 76.1 mm x 25 76.1mm x 32 76.1 mm x 40 76.1mm x 50 80 x 32 3 x 1½ 80 x 40 3 x 1½ 80 x 50 3 x 2 80 x 65 3 x 2½ 80 x 76.1mm 100 x 50 4 x 2 100 x 65 4 x 2½ 100 x 76.1mm 100 x 80 4 x 3

Pipe SS-21 Reducing Tee SS-50 Concentric Reducer O. D. C-E C-B Weight E - E Weight mm / in mm / in mm / in Kgs / Lbs mm / in Kgs / Lbs 48.3 x 33.483 83 83 0.6 64 0.3 1.900 x 1.315 3.25 3.25 1.3 2.50 0.6 48.3 x 42.283 83 83 0.6 64 0.3 1.900 x 1.660 3.25 3.25 1.3 2.50 0.7 60.3 x 33.483 83 83 0.7 64 0.3 2.375 x 1.315 3.25 3.25 1.5 2.50 0.8 60.3 x 42.283 83 83 0.8 64 0.7 2.375 x 1.660 3.25 3.25 1.8 2.50 0.7 60.3 x 48.383 83 83 0.8 64 0.3 2.375 x 1.900 3.25 3.25 1.8 2.50 0.7 73.0 x 33.495 95 95 0.9 64 0.4 2.875 x 1.315 3.74 3.74 2.0 2.50 0.9 73.0 x 42.295 95 95 0.9 64 0.5 2.875 x 1.660 3.74 3.74 2.0 2.50 1.1 73.0 x 48.395 95 95 0.9 64 0.5 2.875 x 1.900 3.74 3.74 2.0 2.50 1.2 73.0 x 60.395 95 95 1.5 64 0.5 2.875 x 2.375 3.74 3.74 3.3 2.50 1.1 76.1 x 33.495 95 95 0.9 64 0.4 3.000 x 1.315 3.74 3.74 2.0 2.50 0.9 76.1 x 42.295 95 95 0.9 64 0.5 3.000 x 1.660 3.74 3.74 2.0 2.50 1.1 76.1 x 48.395 95 95 0.9 64 0.5 3.000 x 1.900 3.74 3.74 2.0 2.50 1.2 76.1 x 60.395 95 95 1.5 64 0.5 3.000 x 2.375 3.74 3.74 3.3 2.50 1.1 88.9 x 42.2108 108 108 1.6 64 0.5 3.500 x 1.660 4.25 4.25 3.5 2.50 1.1 88.9 x 48.3108 108 108 1.3 64 0.6 3.500 x 1.900 4.25 4.25 2.9 2.50 1.5 88.9 x 60.3108 108 108 2.1 64 0.6 3.500 x 2.375 4.25 4.25 4.6 2.50 1.3 88.9 x 73.0108 108 108 2.1 64 1.0 3.500 x 2.875 4.25 4.25 4.6 2.50 2.2 88.9 x 76.1108 108 108 2.1 64 1.0 3.500 x 3.000 4.25 4.25 4.6 2.50 2.2 114.3 x 60.3 127 127 3.3 76 1.0 4.500 x 2.375 5.00 5.00 7.3 3.00 2.2 114.3 x 73.0 127 127 3.3 76 1.4 4.500 x 2.875 5.00 5.00 7.3 3.00 3.1 114.3 x 76.1 127 127 3.3 76 1.4 4.500 x 3.000 5.00 5.00 7.3 3.00 3.1 114.3 x 88.9 127 127 3.2 76 0.9 4.500 x 3.500 5.00 5.00 7.0 3.00 2.0


Nominal Size mm / in 125 x 100 5 x 4 125 x 100 5 x 4 165.1mm x 80 165.1mm x 100 165.1mm x 139.7mm 150 x 80 6 x 3 150 x 100 6 x 4 150 x 125 6 x 5 200 x 100 8 x 4 200 x 125 8 x 5 200 x 150 8 x 6 250 x 150 10 x 6 250 x 200 10 x 8 300 x 200 12 x 8 300 x 250 12 x 10 200 JIS x 100 200 JIS x 125 200 JIS x 165.1mm 250 JIS x 165.1mm 250 JIS x 200 JIS 300 JIS x 200 JIS 300 JIS x 250 JIS

E-E

Pipe SS-21 Reducing Tee SS-50 Concentric Reducer O. D. C-E C-B Weight E - E Weight mm / in mm / in mm / in Kgs / Lbs mm / in Kgs / Lbs 139.7 x 114.3 140 140 5.1 89 1.6 5.500 x 4.500 5.50 5.50 11.2 3.50 3.5 141.3 x 114.3 140 140 5.1 89 1.6 5.563 x 4.500 5.50 5.50 11.2 3.50 3.5 165.1 x 88.9 165 165 7.0 102 2.3 6.500 x 3.500 6.50 6.50 15.4 4.00 5.1 165.1 x 114.3 165 165 8.4 102 2.3 6.500 x 4.500 6.50 6.50 18.5 4.00 5.1 165.1 x 139.7 165 165 8.8 102 2.6 6.500 x 5.500 6.50 6.50 19.4 4.00 5.7 168.3 x 88.9 165 165 7.1 102 2.3 6.625 x 3.500 6.50 6.50 15.6 4.00 5.1 168.3 x 114.3 165 165 8.8 102 2.3 6.625 x 4.500 6.50 6.50 19.4 4.00 5.1 168.3 x 141.3 165 165 8.8 102 2.6 6.625 x 5.563 6.50 6.50 19.4 4.00 5.7 219.1 x 114.3 197 197 16.1 127 4.3 8.625 x 4.500 7.76 7.76 35.4 5.00 9.5 219.1x 141.3 197 197 13.0 127 5.4 8.625 x 5.563 7.76 7.76 28.6 5.00 11.9 219.1 x 168.3 197 197 24.6 127 4.3 8.625 x 6.625 7.76 7.76 54.1 5.00 9.5 273.0 x 168.3 229 229 26.9 152 8.3 10.750 x 6.625 9.02 9.02 59.2 6.00 18.3 267.4 x 216.3 229 229 27.3 152 8.7 10.528 x 8.516 9.02 9.02 60.1 6.00 19.1 323.9 x 219.1 254 254 25.5 178 22.0 12.750 x 8.625 10.00 10.00 56.1 7.00 49.5 323.9 x 273.0 254 254 26.0 178 11.3 12.750 x 10.750 10.00 10.00 57.2 7.00 23.1 216.3 x 114.3 197 197 16.1 127 4.3 8.516 x 4.500 7.76 7.76 35.4 5.00 9.5 216.3 x 139.7 197 197 12.7 127 5.4 8.516 x 5.500 7.76 7.76 27.9 5.00 11.9 216.3 x 165.1 197 197 12.6 127 4.3 8.516 x 6.500 7.76 7.76 27.7 5.00 9.5 267.4 x 165.1 229 229 26.9 152 8.3 10.528 x 6.500 9.0 9.02 59.2 6.00 18.3 267.4 x 216.3 229 229 27.3 152 8.7 10.528 x 8.516 9.02 9.02 60.1 6.0 19.1 318.5 x 216.3 254 254 25.5 178 22.0 12.539 x 8.516 10.00 10.00 56.1 7.00 49.5 318.5 x 267.4 254 254 26.0 178 11.3 12.539 x 110.528 10.00 10.00 57.2 7.00 23.1

www.shurt.com


WROUGHT STAINLESS STEEL FITTINGS

Catalog 2011

MODEL

WS-10 90° ELBOW, S/R WS-10L 90° ELBOW, L/R WS-11 45° ELBOW, L/R WS-20 EQUAL TEE WS-60 CAP Shurt wrought stainless steel grooved fittings are fabricated from Sch. 10S

E-E

stainless steel pipe to ASTM A403 WP-S

C-E

C-E

304 or 316, or welded pipe or plate WP-W. C-E dimensions conform to ANSI B16.9 and B16.28.

WS-10

Nominal Size mm / in 350 14 400 16 450 18 500 20 600 24

Pipe O.D. mm / in 355.6 14.000 406.4 16.000 457.2 18.000 508.0 20.000 609.6 24.000

WS-10 C-E Weight mm / in Kgs / Lbs 355.6 23.59 14.00 51.90 406.4 30.84 16.00 67.85 457.2 40.43 18.00 89.15 508.0 54.90 20.00 121.05 609.6 93.55 24.00 206.27

WS-10L C-E Weight mm / in Kgs / Lbs 533.4 36.30 21.00 79.86 609.6 47.63 24.00 104.79 685.8 59.87 27.00 131.71 762.0 99.79 30.00 219.54 914.4 140.61 36.00 309.34

C-E

C-E WS-10L

WS-11


C-E WS-20


WS-60 WS-60 E-E Weight mm / in Kgs / Lbs 165.0 8.16 6.50 17.95 178.0 14.51 7.00 31.92 203.0 17.96 8.00 39.51 229.0 27.22 9.00 59.88 267.0 34.47 10.50 75.83

MODEL

WS-21 REDUCING TEE Material: ASTM A403 WP-S 304 or 316 Wall thickness: Sch. 10S C-E & C-B dimensions: ANSI B16.9 & B16.28

C-E C-B

WS-21

Nominal Pipe Size mm / in 350 x 150 14 x 6 350 x 200 14 x 8 350 x 250 14 x 10 350 x 300 14 x 12 400 x 150 16 x 6 400 x 200 16 x 8 400 x 250 16 x 10 400 x 300 16 x 12 400 x 350 16 x 14

Pipe O.D. mm / in 355.6 x 168.3 14.000 x 6.625 355.6 x 219.1 14.000 x 8.625 355.6 x 273.0 14.000 x 10.750 355.6 x 323.9 14.000 x 12.750 406.4 x 168.3 16.000 x 6.625 406.4 x 219.1 16.000 x 8.625 406.4 x 273.0 16.000 x 10.750 406.4 x 323.9 16.000 x 12.750 406.4 x 355.6 16.000 x 14.000

WS-21 Reducing Tee C-E C-B mm / in mm / in 279.0 238.0 11.0 9.37 279.0 248.0 11.0 9.76 279.0 257.0 11.0 10.12 279.0 270.0 11.0 10.63 305.0 264.0 12.0 10.40 305.0 273.0 12.0 10.75 305.0 282.0 12.0 11.10 305.0 295.0 12.0 11.61 305.0 305.0 12.0 12.00

Weight Kgs / Lbs 22.19 48.92 23.82 52.52 25.11 55.37 27.16 59.88 27.79 61.28 29.46 64.95 30.87 68.06 33.08 72.95 34.95 77.06

MODEL

WS-50 Concentric

Reducer

Material: ASTM A403 WP-S 304 or 316 Wall thickness: Sch. 10S E-E dimensions: ANSI B16.9 & B16.28

E-E WS-50



Nominal Pipe Size mm / in 350 x 150 14 x 6 350 x 200 14 x 8 350 x 250 14 x 10 350 x 300 14 x 12 400 x 150 16 x 6 400 x 200 16 x 8 400 x 250 16 x 10 400 x 300 16 x 12 400 x 350 16 x 14

Pipe O.D. mm / in 355.6 x 168.3 14.000 x 6.625 355.6 x 219.1 14.000 x 8.625 355.6 x 273.0 14.000 x 10.750 355.6 x 323.9 14.000 x 12.750 406.4 x 168.3 16.000 x 6.625 406.4 x 219.1 16.000 x 8.625 406.4 x 273.0 16.000 x 10.750 406.4 x 323.9 16.000 x 12.750 406.4 x 355.6 16.000 x 14.000

WS-50 Concentric Reducer E-E Weight mm / in Kgs / Lbs 279.0 12.6 11.0 27.8 279.0 14.6 11.0 32.1 279.0 17.1 11.0 37.8 279.0 20.3 11.0 44.7 305.0 16.1 12.0 35.5 305.0 18.2 12.0 40.2 305.0 21.0 12.0 46.2 305.0 22.8 12.0 50.3 305.0 26.7 12.0 58.9

www.shurt.com

Catalog 2011

MODEL

SS-41 FLANGE

ADAPTER - ANSI 125/150

The Model SS-41 stainless steel flange

(316). Integral closure tabs located on

adapter allows for a direct connection with

the flange OD help facilitate alignment and

ANSI Class 125/150 flanges. The SS-41 is

assembly.

investment cast in Gr. CF8 (304) or CF8M Nom. Rating Class 150

C

A

Pressure-Temperature Rating Working Pressure (S40S, Roll-grooved)


300 psi @100°F 20 Bar @38°C


D E

B

• The working pressure shown is based on roll-grooved Sch. 40S pipe. Apply 110% for cut-grooved Sch. 40S pipe. Apply 80% for roll-grooved Sch. 10S pipe and 50% for roll-grooved Sch. 5S pipe. • Proof test pressure: 1.5 times the working pressure, non-shock cold water.

Nominal Size mm / in 50 2 65 2½ 80 3 100 4 150 6 200 8

Pipe O. D. mm / in 60.3 2.375 73.0 2.875 88.9 3.500 114.3 4.500 168.3 6.625 219.1 8.625

Max. Working Pressure Bar / PSI 20 300 20 300 20 300 20 300 20 300 20 300

Max. End Load A kN / Lbs mm / in 5.71 152 1330 6.00 8.37 178 1950 7.00 12.41 190 2880 7.50 20.51 229 4770 9.00 44.47 279 10340 11.00 75.37 343 17520 13.50

Dimensions B C mm / in mm / in 121 21 4.75 0.83 140 22 5.50 0.87 152 24 6.00 0.94 191 24 7.50 0.94 241 25 9.50 1.00 298 28 11.75 1.12

Sealing Surface Bolts D E Size. mm / in mm / in No. in 60 87 4 ⅝x3 2.36 3.42 73 102 4 ⅝x3 2.87 4.00 89 116 4 ⅝x3 3.50 4.56 114 141 8 ⅝x3 4.50 5.56 168 198 8 ¾ x 3½ 6.62 7.79 219 254 8 ¾ x 3½ 8.62 10.00

Weight Kgs / Lbs 2.1 4.6 2.7 6.0 3.1 6.8 4.5 9.9 5.8 12.9 9.2 20.2

* Based on Sch. 10S pipe.

MODEL


Universal Flange Adapter

The Model SS-80 Universal Flange Adapter


provides for a rigid transition between a

Nom. Rating

grooved piping system and a flanged piping system or component. The SS-80 can mate to ANSI 125/150, PN 10/16, BS-10E or JIS 10K, and is available standard in CF8 (304) or CF8M (316). Nominal Size mm / in 50 2 65 2½ 76.1 mm 80 3 100 4 139.7 mm 125 5 165.1 mm 150 6 200 8 200 JIS

Class 150

Z



300 psi @100°F 20 Bar @38°C



X Y

D

L Pipe O. D. Y: Flange Drilling Basic ANSI 125 / 150 PN 10, 16 JIS 10K Z mm / in L X mm / in mm / in mm / in mm / in 60.3 64 165 121 125 120 16 2.375 2.50 6.50 4.75 4.92 4.72 0.63 73.0 70 185 140 145 140 16 2.875 2.75 7.28 5.50 5.70 5.50 0.63 76.1 76 185 140 145 140 16 3.000 3.00 7.28 5.50 5.70 5.50 0.63 88.9 76 200 152 160 150 16 3.500 3.00 7.78 6.00 6.30 5.90 0.63 114.3 76 220 191 180 175 16 4.500 3.00 8.66 7.50 7.09 6.89 0.63 139.7 76 254 216 210 210 22 5.500 3.00 10.00 8.50 8.27 8.27 0.87 141.3 89 254 216 210 210 22 5.563 3.50 10.00 8.50 8.27 8.27 0.87 165.1 76 270 241 240 240 16 6.500 3.00 10.63 9.50 9.45 9.45 0.63 168.3 89 291 241 240 240 24 6.625 3.50 11.46 9.50 9.45 9.45 0.94 219.1 102 343 298 295 29 N/A 8.625 4.00 13.50 11.75 11.61 1.14 216.3 102 343 298 295 23 N/A 8.516 4.00 13.50 11.75 11.61 0.91

Bolt Size mm / in No. M16 4 ⅝ 4 M16 4 ⅝ 4 M16 4 ⅝ 4 M16 8 ⅝ 8 M16 8 ⅝ 8 M16 / M20 8 ⅝ / ¾ 8 M16 / M20 8 ⅝ / ¾ 8 M20 8 ¾ 8 M20 8 ¾ 8 M20 8 / 12 ¾ 8 / 12 M20 8 / 12 ¾ 8 / 12

Weight Kgs / Lbs 2.0 4.4 2.9 6.4 3.0 6.6 3.4 7.5 3.9 8.6 6.7 14.7 6.7 14.7 6.8 15.0 6.9 15.2 14.5 31.9 14.0 30.8

Shurt for other sizes.


www.shurt.com


Catalog 2011

MODEL

SS-723 STAINLESS STEEL MECHANICAL TEE The Shurt Model SS-723 stainless steel

simply cut or drill a hole at the desired

mechanical tee is the ideal fitting for branch

location, position the housing so that the

or direct outlet connections to sprinkler

locating collar fits within the hole and secure

heads, drop nipples and or gauges on

with the bolts and nuts.

stainless steel pipe. No need for welding, C




300 psi @100°F 20 Bar @38°C


• The working pressure shown is based on Sch. 40S pipe. • Proof test pressure: 1.5 times the working pressure, non-shock cold water. • Burst pressure is engineered minimum 3 times the working pressure.

Nominal Size mm / in 32 x 15 1¼ x ½ 32 x 20 1¼ x ¾ 32 x 25 1¼ x 1 40 x 15 1½ x ½ 40 x 20 1½ x ¾ 40 x 25 1½ x 1 50 x 15 2 x ½ 50 x 20 2 x ¾ 50 x 25 2 x 1

A

D

T

B

Hole Dia. +1.6, -0 / +0.063, -0 A B mm / in mm / in mm / in 30 41 26 1.18 1.60 1.02 30 44 26 1.18 1.70 1.02 30 51 26 1.18 2.00 1.02 30 44 29 1.18 1.70 1.13 30 46 29 1.18 1.81 1.13 30 53 29 1.18 2.09 1.13 30 51 36 1.18 2.00 1.42 30 53 36 1.18 2.09 1.42 30 60 36 1.18 2.37 1.42

Dimensions C D mm / in mm / in 87 49 3.44 1.93 87 49 3.44 1.93 87 49 3.44 1.93 90 49 3.54 1.93 90 49 3.54 1.93 90 49 3.54 1.93 109 51 4.28 2.00 109 51 4.28 2.00 109 51 4.28 2.00

Bolt T* Size Weight mm / in in Kgs / Lbs 27 0.3 5/16 x 1½ 1.06 0.7 29 0.3 5/16 x 1½ 1.14 0.7 34 0.4 5/16 x 1½ 1.34 0.9 30 0.3 5/16 x 1½ 1.18 0.7 31 0.3 5/16 x 1½ 1.22 0.7 36 0.4 5/16 x 1½ 1.42 0.9 37 0.5 5/16 x 1½ 1.46 1.1 28 0.5 5/16 x 1½ 1.10 1.1 43 0.6 5/16 x 1½ 1.69 1.4

T*: Take-out (Center of run to end of pipe to be engaged)

MODEL

SS-726 STAINLESS STEEL Y-STRAINER The Model SS-726 Stainless Steel Grooved-

Cleaning and maintenance of the screen

end Y-Strainers are designed to strain debris

can be accomplished easily by removing

and foreign matter from piping systems

the coupling. The Model SS-726 Stainless

and thus provide inexpensive protection for

Steel Y-Strainer is suitable for vertical or

costly pumps, meters and other components.

horizontal installations.

B




300 psi @100°F 20 Bar @38°C


A

C


Nominal Size mm / in 65 2½ 80 3 100 4 150 6


Pipe OD mm / in 73.0 2.875 88.9 3.500 114.3 4.500 168.3 6.625

Max. Working Pressure A bar / psi mm / in 20 273 300 10.75 20 299 300 11.75 20 362 300 14.25 20 470 300 18.50


Dimensions B C mm / in mm / in 199 122 7.83 4.80 221 129 8.70 5.08 269 168 10.59 6.61 357 219 14.05 8.62

Drain Plug Size mm / in 15 ½ 15 ½ 25 1 25 1

www.shurt.com

Weight Kgs / Lb 7.6 16.7 8.6 18.9 9.6 21.1 39.0 85.8

Catalog 2011

MODEL

SJ-600L Ball Valve The Model SJ-600L is a two-piece, full-port

torque and is supplied with a lever handle as

stainless steel ball valve rated at 600 psi (40

well as ISO mounting holes to accommodate

bar) and is available in CF8M (316). The

a full range of gear or power actuators.

SJ-600L features a floating ball for lower Pressure-Temperature Rating Nom. Rating

Working Pressure (S40S, Roll-Grooved)

Shell Test (Hydrostatic)


600 psi @100°F 42 Bar @38°C

900 psi 63 Bar


CWP

Size: 4" W

*Working pressure is for connection with cut- or roll-grooved schedule Sch. 40S pipe. *Seat test: 110% the working pressure.

H d

L Nominal Size mm / in 40 1½ 50 2 65 2½ 76.1 mm 80 3 100 4

Pipe OD mm / in 48.3 1.900 60.3 2.375 73.0 2.875 76.1 3.000 88.9 3.500 114.3 4.500

Operating Torque L Lb - in / N - m mm / in 7 140 62 5.50 17 156 150 6.15 21 180 186 7.09 21 180 186 7.09 28 214 248 8.42 45 240 398 9.45

Size: 1½" - 3" H mm / in 94 3.70 105 4.13 110 4.33 110 4.33 152 6.00 167 6.57

Dimensions W mm / in 193 7.60 193 7.60 250 9.84 250 9.84 250 9.84 290 11.42

d mm / in 38 1.50 50 1.97 65 2.56 65 2.56 78 3.07 100 3.94

Approx. Weight Kgs / Lbs 3.0 6.6 4.0 8.8 7.0 15.4 7.0 15.4 9.4 20.7 25.0 55.0

* The weight includes the lever handle.

MODEL

SJ-600W Ball Valve The Model SJ-600W is supplied with a worm

W

K

gear operator. The standard gear operator is supplied with a bracket and extension

H

sleeve. Sizes available are 2"/50mm through 4"/100mm.

Nominal Size mm / in 50 2 65 2½ 76.1 mm 80 3 100 4

Pipe OD K mm / in mm / in 60.3 152 2.375 6 73.0 152 2.875 6 76.1 152 3.000 6 88.9 152 3.500 6 114.3 152 4.500 6

Dimensions H W mm / in mm / in 137 203 5.38 8 145 203 5.68 8 145 203 5.68 8 182 203 7.16 8 203 203 8.00 8

Approx. Weight Kgs / Lbs 8.10 17.82 11.10 24.42 11.10 24.42 13.50 29.70 29.0 63.80

* The weight includes the worm gear operator.


www.shurt.com


Catalog 2011

MODEL

SJ-400 BUTTERFLY VALVE The Shurt Model SJ-400 Butterfly Valve

(type 316) to ASTM A743 with integral neck

is a grooved end stainless steel butterfly

and ISO 5211 mounting pad. It features a

valve, supplied with a 10 position lever

dual seal disc encapsulated with Gr. E EPDM

handle (SJ-400-L) or worm gear operator

for cold and hot water services. The end-to-

(SJ-400-W). The body is available in CF8M

end dimensions conform to MSS SP-67.




300 psi @100°F 20 Bar @38°C


• The working pressure shown is based on roll-grooved Sch. 40S pipe. Apply 110% for cut-grooved Sch. 40S pipe. Apply 80% for roll-grooved Sch. 10S pipe and 50% for roll-grooved Sch. 5S pipe. • Seat test: 110% the working pressure. • Shell test: 1.5 times the working pressure.

SJ-400-W 14“-24”

E E

SJ-400-L 2“-12” F

D

D O. D.

O. D.

C

B Nominal Size mm / in 50 2 65 2½ 76.1 mm 80 3 100 4 165.1 mm 150 6 200JIS 200 8 250 10 300 12 350 14 400 16 450 18 500 20 600 24

Pipe O. D. A B mm / in mm / in mm / in 60.3 81 64 2.375 3.19 2.520 73.0 97 80 2.875 3.81 3.150 76.1 97 80 3.000 3.81 3.150 88.9 97 92 3.500 3.81 3.622 114.3 116 118 4.500 4.56 4.646 165.1 148 172 6.500 5.81 6.772 168.3 148 172 6.625 5.81 6.772 216.3 133 222 8.516 5.24 8.740 219.1 133 222 8.625 5.24 8.740 273.0 160 284 10.750 6.30 11.18 323.9 166 334 12.750 6.56 13.15 355.6 178 359 14.000 7.00 14.13 406.4 178 410 16.000 7.00 16.14 457.2 203 464 18.000 8.00 18.25 508.0 216 515 20.000 8.50 20.28 609.6 254 616 24.000 10.00 24.25

B

A

A

SJ-400-W Dimensions C D mm / in mm / in 63 106 2.480 4.17 68 111 2.677 4.28 68 111 2.677 4.28 76 126 2.992 4.97 89 135 3.504 5.33 114 168 4.488 6.62 114 184 4.488 7.25 140 208 5.512 8.20 140 208 5.512 8.20 186 235 7.32 9.25 213 260 8.39 10.24 224 276 8.82 10.87 248 302 9.76 11.89 283 350 11.14 13.78 314 383 12.36 15.08 368 453 14.50 17.83

E mm / in 192 7.56 192 7.56 192 7.56 192 7.56 252 9.92 252 9.92 342 13.46 342 13.46 342 13.46 252 9.92 356 14.02 203 8.00 242 9.50 242 9.50 290 11.40 290 11.40

Operating Torque Weight N-m / In - Lb Kgs / Lbs 8.80 2.3 78 5.0 9.50 3.2 84 7.0 9.50 3.2 84 7.0 10.7 3.5 95 6.6 22.6 5.0 200 11.0 34.9 9.2 310 20.2 34.9 9.2 310 20.2 45.1 12.2 400 26.8 45.1 12.2 400 26.8 170 28.3 1500 31.3 226 40.0 2000 88.0 254 59.0 10.0 130.0 306 67.0 12.00 147.4 305 86.0 12.00 189.2 412 133.0 16.20 292.6 412 160.0 16.20 352.0

* The weight includes the lever handle or worm gear operator.



www.shurt.com

Section 4 Valves and Flow Control Components Valves and Flow Control Components..............................76 SJ-200 Low-profile Butterfly Valve..................................................... 77 SJ-300N Butterfly Valve.................................................................... 78 SJ-300F Butterfly Valve (for Fire Protection)..................................... 79 SJ-500L / SJ-500W Ball Valves..................................................... 80 SJ-900 Swing Check Valve................................................................ 81 SJ-915 Dual Disc Check Valve.......................................................... 82 SJ-930 Horizontal Swing Check Valve............................................... 83 650N Expansion t......................................................................... 84 651 Expansion t........................................................................... 85 725F Suction Diff........................................................................ 86 726 Y-Strainer.................................................................................... 88 728 T-Strainer.................................................................................... 89 RCV Riser Check Valve (for Fire Protection)...................................... 90


Catalog 2011

www.shurt.com

Catalog 2011

Valves and Flow Control Components Shurt offers a complete range of grooved-end butterfly valves, ball valves, check valves, suction diffs, strainers and expansion ts. Grooved-end valves and components can be installed 3 – 4 times faster than comparable flange components. With the removal of just a few bolts one can easily access the system for cleaning, maintenance, changes and or system expansion.

SJ-300L Butterfly Valve 726 Y-Strainer 7110LR 90° Elbow 7180 Universal Flange Adapter 7041 Flange 7150 Concentric Reducer SJ-900 Check Valve 7707 Flexible Coupling Z07 Rigid Coupling 7721 Mechanical Tee with Pressure Gage

SJ-300L Butterfly Valve 725F Suction Diff 7041 Flange 7150 Concentric Reducer SJ-915 Dual Disc Check Valve 7707 Flexible Coupling Z07 Rigid Coupling 7721 Mechanical Tee with Pressure Gage

Model 726 Y-strainers, SJ-300N butterfly valves and SJ-900 check valves used on a chill water system.



www.shurt.com

Catalog 2011

MODEL

SJ-200 LOW-PROFILE BUTTERFLY VALVE The Shurt Model SJ-200 Butterfly Valve

(Nitrile body liner). The Model SJ-200

is a low profile, grooved-end butterfly valve

features a fully rubber lined body with

designed for oil & gas, mining and other

316 stainless steel disc. The end to end

service applications. The working pressure

dimensions conform to MSS SP-67. The

is rated up to 232 psi / 1600 kPa and service

lever handle is equipped with a tamper

temperatures are rated to +180°F / +82°C

resistant locking device.


CWP

Working Pressure

Shell Test

232 psi @100°F 350 psi 16 Bar @38°C

24 Bar


*Working pressure is based on connection with roll- or cut-grooved standard wall carbon steel pipe. *Seat test: 110% the working pressure.

H

Not Recommended for Steam. C O. D. B A


Pipe O. D. A mm / in mm / in 60.3 81 2.375 3.19 73.0 97 2.875 3.82 88.9 97 3.500 3.82 114.3 116 4.500 4.57 168.3 148 6.625 5.83 219.1 133 8.625 5.25


Dimensions B C H mm / in mm / in mm / in 48 57 140 1.89 2.25 5.51 54 67 190 2.13 2.65 7.48 62 75 190 2.44 2.94 7.48 76 97 274 3.00 3.82 10.79 104 116 274 4.09 4.57 10.79 140 152 274 5.50 6.00 10.79

www.shurt.com

Approx. Weight Kgs / Lbs 0.9 2.0 1.5 3.3 1.9 4.2 3.9 8.6 10.1 22.2 11.3 27.9


Catalog 2011

MODEL

SJ-300N BUTTERFLY VALVE The Shurt Model SJ-300N Butterfly

epoxy coated ductile iron body and EPDM or

Valve is a grooved-end shut-off valve

Nitrile (NBR) rubber encapsulated dual-seal

equipped with a 10 position lever handle

disc. The end-to-end dimensions conform to

(SJ-300N-L) or worm gear operator

MSS SP-67.

(SJ-300N-W). The valve consists of an Pressure-Temperature Rating Nom. Rating

Working Pressure

Shell Test


Class

300 psi @100°F

450 psi

EPDM: 230°F / 110°C

20 Bar @38°C

30 Bar


150

Dual-Seal


SJ-300N-W w / worm gear E O

S

F E

D D

O. D.

O.D.

SJ-300N-L w / lever handle Nominal Size mm / in 50 2 65 2½ 76.1 mm 80 3 100 4 139.7 mm 125 5 165.1 mm 150 6 200JIS 200 8 250 10 300 12 350 14 400 16 450 18 500 20 600 24

Pipe O.D. A B mm / in mm / in mm / in 60.3 81 64 2.375 3.19 2.52 73.0 97 79 2.875 3.82 3.11 76.1 97 79 3.000 3.82 3.11 88.9 97 92 3.500 3.82 3.62 114.3 116 118 4.500 4.57 4.65 139.7 148 145 5.500 5.83 5.71 141.3 148 145 5.563 5.83 5.71 165.1 148 172 6.500 5.83 6.77 168.3 148 172 6.625 5.83 6.77 216.3 133 222 8.516 5.24 8.74 219.1 133 222 8.625 5.24 8.74 273.0 159 276 10.750 6.25 10.86 323.9 165 327 12.750 6.53 12.87 355.6 178 365 14.000 7.00 14.37 406.4 178 416 16.000 7.00 16.38 457.2 203 470 18.000 8.00 18.50 508.0 216 527 20.000 8.50 20.75 609.6 254 629 24.000 10.00 24.76

C

C B Dimensions C mm / in 63 2.48 68 2.68 68 2.68 76 2.99 89 3.50 102 4.02 102 4.02 114 4.49 114 4.49 140 5.51 140 5.51 170 6.69 205 8.07 224 8.82 248 9.76 283 11.14 314 12.36 368 14.49

A

B

A

Lever Handle Type D E Operating Torque Weight mm / in mm / in N - m / In - Lb Kgs / Lbs 106 192 9 3.1 4.17 7.56 80 6.8 111 192 14 3.7 4.37 7.56 120 8.2 111 192 14 3.8 4.37 7.56 120 8.4 126 192 18 4.1 4.96 7.56 160 9.0 135 260 51 5.2 5.32 10.24 450 11.4 168 260 79 7.7 6.61 10.24 700 16.9 168 260 79 7.7 6.61 10.24 700 16.9 184 260 102 9.2 7.24 10.24 900 20.2 184 260 102 9.2 7.24 10.24 900 20.2 208 260 136 12.2 8.19 10.24 1200 26.8 208 260 136 12.2 8.19 10.24 1200 26.8 235 356 204 22.0 9.25 14.02 1800 48.4 260 356 282 33.5 10.24 14.02 2500 73.7 276 --- --- --- 10.86 --- --- --- 302 --- --- --- 11.89 350 --- --- --- 13.78 --- --- --- 383 --- --- --- 15.08 --- --- --- 453 --- --- --- 17.83 --- --- ---

Worm Gear Type E F mm / in mm / in 152 152 6.00 6.00 152 152 6.00 6.00 152 152 6.00 6.00 152 152 6.00 6.00 152 152 6.00 6.00 152 152 6.00 6.00 152 152 6.00 6.00 152 152 6.00 6.00 152 152 6.00 6.00 152 152 6.00 6.00 152 152 6.00 6.00 203 203 8.00 8.00 203 203 8.00 8.00 203 203 8.00 8.00 242 305 9.50 12.00 242 305 9.50 12.00 290 412 11.40 16.20 290 412 11.40 16.20

* The weight includes the lever handle or worm gear operator.



www.shurt.com

Weight Kgs / Lbs 6.2 13.6 6.5 14.3 6.5 14.3 7.3 16.0 8.7 19.1 9.9 21.8 9.9 21.8 11.4 25.0 11.5 25.3 14.5 31.9 14.5 32.0 27.0 59.4 33.5 73.7 59.0 130.0 67.0 147.4 86.0 189.2 133.0 292.6 160.0 352.0

Catalog 2011

SJ-300F BUTTERFLY VALVE The Model SJ-300F Butterfly Valve is a

UL Specification 1091 and FM Approval

grooved-end shut-off valve equipped with

Standard 1112.

a weatherproof worm gear operator and

When the Model SJ-300F Butterfly Valve is

supervisory switch and wiring.

used in a fire protection piping, installation

The Model SJ-300F is FM approved for

shall conform to NFPA 13 and NFPA 72.

300 psi (20 Bar, 2.0 MPa) WWP (water

The valve consists of an epoxy powder

working pressure) service for indoor and

coated ductile iron body and EPDM rubber

outdoor use. Flow characteristics satisfy

encapsulated dual-seal disc.


CWP

Working Pressure

Shell Test

300 psi @100°F 1500 psi 20 Bar @38°C

105 Bar

F


Model SJ-300F Butterfly Valve

EPDM: 230°F / 110°C

Working pressure is based on connection with roll- or cut-grooved standard wall carbon steel pipe. *Seat test: 2 times the working pressure.

G

D

E

O.D. C A

Nominal Size mm / in 65 2½ 76.1 mm 80 3 100 4 139.7mm 125 5 165.1 mm 150 6

Pipe OD A(1) B C mm / in mm / in mm / in mm / in 73.0 97 80 68 2.875 3.81 3.15 2.68 76.1 97 80 68 3.000 3.81 3.15 2.68 88.9 97 92 76 3.500 3.81 3.62 3.00 114.3 116 118 89 4.500 4.56 4.65 3.50 139.7 148 145 102 5.500 5.81 5.71 4.00 141.3 148 145 102 5.563 5.81 5.71 4.00 165.1 148 172 114 6.500 5.81 6.77 4.50 168.3 148 172 114 6.625 5.81 6.77 4.50

Dual Seal

B

Dimensions D mm / in 111 4.37 111 4.37 126 4.96 135 5.31 168 6.61 168 6.61 184 7.25 184 7.25

E mm / in 210 8.27 210 8.27 233 9.17 255 10.04 301 11.85 301 11.85 329 12.95 329 12.95

F mm / in 92 3.62 92 3.62 92 3.62 92 3.62 92 3.62 92 3.62 92 3.62 92 3.62

G mm / in 163 6.42 163 6.42 163 6.42 163 6.42 163 6.42 163 6.42 163 6.42 163 6.42

Weight Kgs / Lbs 8.8 17.9 8.8 17.9 9.2 20.3 10.6 23.4 14.3 31.6 14.4 31.6 16.1 35.5 16.1 35.5

(1) End to end dimensions conform to MSS SP-67. (2) The weight includes the worm gear operator.


www.shurt.com


Catalog 2011

MODEL

SJ-500L BALL VALVE The Model SJ-500L is a ductile iron,

locking holes. The SJ-500L is comprised of

grooved-end, two-piece, regular port ball

a ductile iron body and end cap, virgin TFE

valve designed and tested in conformance

seats and chrome-plated carbon steel trim.

with MSS SP-110 and SP-72. The lever

Also available with stainless steel trim as an

handle is equipped with tamper resistant

option.

W


W

Working Pressure

Shell Test

CWP

1½” – 3” 40 - 80 4" – 6" 100 – 150


1500 psi 105 Bar 1200 psi 84 Bar


A H


Nominal Size mm / in 40 1½ 50 2 65 2½ 76.1 mm 80 3 100 4 165.1 mm 150 6

Pipe O.D. mm / in 48.3 1.900 60.3 2.375 73.0 2.875 76.1 3.000 88.9 3.500 114.3 4.500 165.1 6.500 168.3 6.625

Working Pressure Bar / Psi 70 1000 70 1000 70 1000 70 1000 70 1000 56 800 56 800 56 800

C

d


B

O. D.

Size in / mm

O. D.

Nom. Rating

d

L

1½" - 4"

Operating Torque* L H W N / m L b - in mm / in mm / in mm / in 7 130 86 178 62 5.12 3.39 7.00 17 140 95 178 150 5.50 3.75 7.00 21 159 132 265 186 6.25 5.20 10.43 21 159 132 265 186 6.25 5.20 10.43 28 167 143 265 248 6.56 5.63 10.43 45 240 94 265 398 9.45 3.70 10.43 60 258 221 600 531 10.15 8.70 23.60 60 258 221 600 531 10.15 8.70 23.60

H

6"

L

Dimensions d A B C mm / in mm / in mm / in mm / in 32 15.9 7.9 45.1 1.25 0.625 0.312 1.775 38 15.9 7.9 57.2 1.50 0.625 0.312 2.250 50 15.9 7.9 69.1 2.00 0.625 0.312 2.720 50 15.9 7.9 72.3 2.00 0.625 0.312 2.845 63 15.9 7.9 84.9 2.50 0.625 0.312 3.344 90 15.9 7.9 110.0 3.50 0.625 0.312 4.334 125 15.9 9.5 163.9 4.92 0.625 0.374 6.453 125 15.9 9.5 163.9 4.92 0.625 0.374 6.453

Approx. Weight Kgs / Lbs 1.8 3.9 2.9 6.4 4.4 9.7 4.4 9.7 7.8 17.2 14.7 32.3 41.1 90.2 41.1 90.2

* When first opening or closing the valve when not continuosly operated.

MODEL

SJ-500W BALL VALVE WITH GEAR OPERATOR The Model SJ-500W can be equipped with

W

a worm gear operator. The standard gear operator is supplied with a bracket and extension sleeve. The ISO 5211 mounting

W

K K H

H

pad allows for the mounting of power actuators. 1½" - 4" Nominal Size mm / in 40 1½ 50 2 65 2½ 76.1 mm 80 3 100 4 165.1 mm 150 6


Pipe O. D. K mm / in mm / in 48.3 152 1.900 6 60.3 152 2.375 6 73.0 152 2.875 6 76.1 152 3.000 6 88.9 152 3.500 6 114.3 152 4.500 6 165.1 305 6.500 12 168.3 305 6.625 12


6" Dimensions H W mm / in mm / in 124 203 4.88 8 137 203 5.38 8 145 203 5.68 8 145 203 5.68 8 182 203 7.16 8 203 203 8.00 8 277 356 10.89 14 277 356 10.89 14

www.shurt.com

Approx. Weight Kgs / Lbs 7.0 15.4 8.0 17.6 10.0 22.0 10.0 22.0 14.0 30.8 33.0 72.6 56.0 123.2 56.0 123.2

Catalog 2011

MODEL

SJ-900 SWING CHECK VALVE The Shurt Model SJ-900 Swing Check

a rated working pressure of 300 psi (20 bar),

Valve is a grooved-end check valve featuring

the valve can be installed in the horizontal or

a spring-loaded wide-open clapper and a

vertical position (upward flow only). Valves

non-stick leak tight EPDM rubber seal. With

are tested to API 598.


Working Pressure

Shell Test


Class

300 psi @100°F

450 psi

EPDM: 230°F / 110°C

20 Bar @38°C

30 Bar


150


A

B

C

Nominal Size mm / in 65 2½ 76.1mm 80 3 100 4 139.7 mm 125 5 165.1 mm 150 6 200 8 250 10 300 12 200 JIS 250 JIS 300 JIS

Pipe O. D. A mm / in mm / in 73.0 190 2.875 7.48 76.1 190 3.000 7.48 88.9 178 3.500 7.00 114.3 216 4.500 8.50 139.7 330 5.500 13.00 141.3 330 5.563 13.00 165.1 305 6.500 12.00 168.3 305 6.625 12.00 219.1 365 8.625 14.37 273.0 508 10.750 20.00 323.9 610 12.750 24.00 216.3 365 8.516 14.37 267.4 508 10.528 20.00 318.5 610 12.539 24.00


Dimensions B C mm / in mm / in 114 95 4.50 3.75 114 95 4.50 3.75 114 95 4.50 3.75 146 117 5.75 4.60 210 178 8.25 7.00 210 178 8.25 7.00 210 178 8.25 7.00 210 178 8.25 7.05 260 217 10.23 8.54 365 273 14.37 10.75 398 327 15.67 12.87 260 217 10.23 8.54 365 273 14.37 10.75 398 327 15.67 12.87

www.shurt.com

Weight Kgs / Lbs 5.0 11.0 4.9 10.8 4.9 10.8 8.3 18.3 23.5 51.7 23.5 51.7 23.5 51.7 23.5 51.7 45.3 99.7 99.0 217.8 155.6 342.3 45.3 99.7 98.5 216.7 155.6 342.3


Catalog 2011

MODEL

SJ-915 DUAL DISC CHECK VALVE The Shurt Model SJ-915 is a grooved-

body with an EPDM or Nitrile (NBR) resilient

end dual-plate (or double-door) check

seat molded to the body and type 304

valve designed to provide positive and

stainless steel discs loaded with type 313

silent protection against backflow in piping

stainless steel springs.

systems. The valve features a ductile iron B


Working Pressure

Shell Test


Class

300 psi @100°F

450 psi

EPDM: 230°F / 110°C

20 Bar @38°C

30 Bar


150

A


Size: 2½"~12" C

Nominal Size mm / in 65 2½ 80 3 100 4 150 6 200 8 250 10 300 12

Pipe O. D. A mm / in mm / in 73.0 125 2.875 4.92 88.9 135 3.500 5.31 114.3 137 4.500 5.39 168.3 152 6.625 6.00 219.1 171 8.625 6.73 273.0 198 10.750 7.80 323.9 208 12.750 8.19

Dimensions B C mm / in mm / in 110 73 4.33 2.87 125 89 4.92 3.50 152 114 5.98 4.50 204 168 8.03 6.62 256 219 10.08 8.62 307 273 12.09 10.75 362 324 14.25 12.75

Approx. Weight Kgs / Lbs 2.3 5.0 2.5 5.5 3.8 8.4 7.6 11.7 12.4 27.3 20.7 45.5 28.3 62.2

The Shurt Model SJ-915 is also available in sizes 14” to 24” / 350mm to 600mm. Face-to-face dimensions conform to API 594 Class 150 and grooved ends to ANSI/AWWA C606. Pressure-Temperature Rating Nom. Rating

Working Pressure

Shell Test


Class

250 psi @100°F

400 psi

EPDM: 230°F / 110°C

17 Bar @38°C

26 Bar


150


A B C

E

D O.D.

Nominal Size mm / in 350 14 400 16 450 18 500 20 600 24


Pipe O. D. A B mm / in mm / in mm / in 355.6 368 329 14.000 14.49 12.96 406.4 410 359 16.000 16.14 14.13 457.2 461 417 18.000 18.15 16.42 508.0 509 460 20.000 20.04 18.11 609.6 610 562 24.000 24.00 22.13


Size: 14"~24"

Dimensions C D E mm / in mm / in mm / in 184 283 154 7-1/4 11.14 6.06 191 310 173 7-1/2 12.20 6.81 203 364 203 8 14.33 8.00 219 408 226 8-5/8 16.06 8.80 222 457 249 8-3/4 18.00 9.80

www.shurt.com


Catalog 2011

MODEL

SJ-930 Horizontal Swing Check Valve Shurt Model SJ-930 horizontal swing

coupling. The 316 stainless steel clapper is

check valves are supplied with grooved

supplied standard encapsulated with Nitrile.

ends and are designed for general services

As an option we offer Fluoroelastomer

including mining and oilfield applications.

(Viton®) or Teflon encapsulations to meet

The SJ-930 features a bonnet cap which

your service requirements.

is drilled, tapped (1/2" NPT), and plugged and secured using a Shurt XH-1000


Size in / mm

Nom. Rating

Working Pressure

Shell Test

2” – 2½” Class 400 50 - 65

1000 psi @100°F 70 Bar @38°C

1500 psi 105 Bar

3" – 4" Class 300 80 – 100

600 psi @100°F 40 Bar @38°C

900 psi 60 Bar


A


UP

*Working pressure is based on connection with cut-grooved standard wall carbon steel pipe. *Seat test: 110% the working pressure.

Nominal Size mm / in 60 2 65 2½ 80 3 100 4

Pipe O. D. mm / in 60.3 2.375 73.0 2.875 88.9 3.500 114.3 4.500

C

Max Working Pressure A Bar / Psi mm / in 70 229 1000 9.00 70 235 1000 9.25 40 273 600 10.75 40 305 600 12.00

Dimensions B C mm / in mm / in 124 150 4.88 5.90 140 178 5.50 7.00 146 188 5.75 7.40 194 222 7.63 8.74

B

Approx. Weight Kgs / Lbs 6.6 14.5 10.4 22.9 12.2 26.8 17.3 38.1

*Pressure ratings are based on cut-grooved sch. 40 or thicker pipe connected with Shurt XH-1000 extra heavy rigid couplings.

Viton® is a ed trademark of DuPont.


www.shurt.com


Catalog 2011

MODEL

650N EXPANSION T The Shurt Model 650N Expansion t

excess movement and or the accidental pull-

is a slide-type expansion t which provides

out of the grooved end pieces. The Model

0 to 3" (0 to 76mm) of axial end movement.

650N can also be supplied with plain-ends

The components are supplied epoxy coated

for use with the Model 79 Wildcat plain-end

(RAL3000 red) for ease of use and longer

coupling.

life. An integral safety device prevents Pressure-Temperature Rating Nom. Rating

Working Pressure


Class

300 psi @100°F

EPDM: 230°F / 110°C

20 Bar @38°C


150

*Working pressure is based on connection with roll- or cut-grooved standard wall carbon steel pipe. *Shell test, 1.5 times the working pressure, is the proof test pressure. *Burst pressure is engineered minimum 3 times the working pressure.

A B

L min. L max.

Nominal Size mm / in 50 2 65 2½ 76.1 mm 80 3 100 4 165.1 mm 150 6


Pipe O. D. mm / in 60.3 2.375 73.0 2.875 76.1 3.000 88.9 3.500 114.3 4.500 165.1 6.500 168.3 6.625

Max. Working Pressure Bar / PSI 20 300 20 300 20 300 20 300 20 300 20 300 20 300


Max. Movement A mm / in mm / in 76 96 3 3.78 76 116 3 4.57 76 116 3 4.57 76 146 3 5.76 76 160 3 6.30 76 260 3 10.25 76 260 3 10.25

Dimensions B L min. L max. mm / in mm / in mm / in 144 304 381 5.67 12.00 15.00 168 304 381 6.61 12.00 15.00 168 304 381 6.61 12.00 15.00 198 304 381 7.80 12.00 15.00 250 359 435 9.84 14.13 17.13 334 406 482 13.15 16.00 19.00 334 406 482 13.15 16.00 19.00

www.shurt.com

Approx. Weight Kgs / Lbs 6.3 13.9 8.7 19.1 8.5 18.7 12.3 27.1 18.4 40.5 41.8 92.0 42.8 94.2

Catalog 2011

MODEL

651 EXPANSION T The Model 651 Expansion t is a

or Model 7707 flexible couplings and cut-

combination of couplings and specially

grooved Sch. 40 pipe nipples. Customized

machined pipe nipples that are ed in a

units are available. The components are

series to accommodate the expansion and

supplied epoxy coated (RAL3000 red) for

or contraction of a piping system. Standard

ease of use and longer life.

units are comprised of either Model 7705 Pressure-Temperature Rating Nom. Rating



Class

300 psi @100°F

EPDM: 230°F / 110°C

150

20 Bar @38°C


*Working pressure is based on connection with roll- or cut-grooved standard wall carbon steel pipe. *Shell test, 1.5 times the working pressure, is the proof test pressure. *Burst pressure is engineered minimum 3 times the working pressure.

L min.

L max.

Nominal Size mm / in 40 1½ 50 2 65 2½ 76.1 mm 80 3 100 4 133.0 mm 165.1 mm 150 6 200 8 250 10 300 12

Pipe O. D. mm / in 48.3 1.900 60.3 2.375 73.0 2.875 76.1 3.000 88.9 3.500 114.3 4.500 133.0 5.250 165.1 6.500 168.3 6.625 219.1 8.625 273.0 10.750 323.9 12.750


Max. Movement mm / in 58 2.25 58 2.25 58 2.25 58 2.25 58 2.25 45 1.75 45 1.75 45 1.75 45 1.75 45 1.75 45 1.75 45 1.75

L min. mm / in 718 28.25 718 28.25 718 28.25 718 28.25 718 28.25 667 26.26 667 26.25 667 26.26 667 26.26 667 26.26 826 32.50 826 32.50

L Max. mm / in 776 30.55 776 30.55 776 30.55 776 30.55 776 30.55 712 28.00 712 28.00 712 28.00 712 28.00 769 30.28 870 34.25 870 34.25

www.shurt.com

Approx. Weight Kgs / Lbs 11.0 24.2 12.2 27.0 16.3 36.0 16.3 36.0 20.9 46.0 16.6 36.5 32.7 72.0 26.4 58.1 41.4 91.1 72.6 159.7 145.3 320.0 169.3 373.0


Catalog 2011

MODEL

725F SUCTION DIFF The Shurt Model 725F Suction Diff

available to ANSI Class 150, PN 10/16, BS

features a space saving design, ductile iron

10 Table E or JIS 10K.

body and integral vanes that effectively

The Model 725F is supplied with a 304

reduce turbulence and provide optimum flow

stainless steel running strainer and a

conditions at the inlet side of the pump.

disposable fine mesh screen to protect the

The 725F allows for direct connection to

pump during start-up operation.

a flanged end pump. Flange drilling is Pressure-Temperature Rating Nom. Rating

Working Pressure


Class

300 psi @100°F

EPDM: 230°F / 110°C

20 Bar @38°C


150

*Working pressure is based on connection with roll- or cut-grooved standard wall carbon steel pipe. *Shell test, 1.5 times the working pressure, is the proof test pressure.

C-E C-T

When ordering, specify the desired flange drilling.

L

Nominal Size Dimensions Flange Suction Side Pump Side L C - E C - T Drain Drilling mm / in mm / in mm / in mm / in mm / in in 50 2 80 65 279 162 140 ¾ 3 2½ 11.00 6.38 5.50 NPT 80 3 65 2½ 100 80 330 187 165 1 4 3 13.00 7.38 6.50 NPT 100 4 100 4 150 125 406 229 203 1 6 5 16.00 9.00 8.00 NPT ANSI Class 150 150 • 6 PN 10/16 125 • 5 BS10 Table E 200 150 483 260 229 1 or 8 6 19.00 10.25 9.00 NPT JIS 10K 200 8 150 6 250 200 584 314 279 1¼ 10 8 23.00 12.38 11.00 NPT 250 10 200 8 300 250 686 394 305 1¼ 12 10 27.00 15.50 12.00 NPT 300 12



www.shurt.com

Approx. Weight Kgs / Lbs 10.5 23.1 12.0 26.4 13.0 28.6 14.0 30.8 15.0 33.0 16.0 35.2 30.0 66.0 30.0 66.0 31.0 68.2 45.0 99.0 47.0 103.4 52.0 114.4 65.0 143.0 68.0 149.6 70.0 154.0 110.0 242.0 115.0 253.0 126.0 277.2

Catalog 2011

MODEL

725F SUCTION DIFF - FABRICATED Shurt Model 725F Suction Diffs in sizes 14” to 24” (350 to 600mm) are fabricated from carbon steel pipe materials. Flange drilling is available to ANSI Class 150, PN 10/16, BS 10 Table E or JIS 10K.

C-E


Working Pressure


Class

300 psi @100°F

EPDM: 230°F / 110°C

20 Bar @38°C


150


Nominal Size Suction Side Pump Side L mm / in mm / in mm / in 250 889 10 35.00 350 300 889 14 12 35.00 350 965 14 38.00 300 965 12 38.00 400 350 965 16 14 38.00 400 1067 16 42.00 350 1067 14 42.00 450 400 1067 18 16 42.00 450 1270 18 50.00 400 1270 16 50.00 500 450 1270 20 18 50.00 500 1346 20 53.00 450 1372 18 54.00 600 500 1372 24 20 54.00 550 1600 22 63.00


C-T

L

Model 725F When ordering, specify the desired flange drilling.

Dimensions Flange C - E C - T Drain Drilling mm/in mm/in in 610 356 24.00 14.00 162 356 ¾ 6.38 14.00 NPT 660 406 26.00 16.00 660 419 26.00 16.50 660 419 1 26.00 16.50 NPT 724 445 28.50 17.50 ANSI Class 150 724 445 • 28.50 17.50 PN 10/16 724 445 1 • 28.50 17.50 NPT BS10 Table E 889 508 or 35.00 20.00 JIS 10K 889 508 35.00 20.00 889 508 1 35.00 20.00 NPT 927 597 36.50 23.50 940 521 37.00 20.50 940 521 1¼ 37.00 20.50 NPT 1105 606 43.50 23.88

www.shurt.com

Approx. Weight Kgs / Lbs 191 420 202 444 242 532 232 510 242 532 312 686 306 673 312 686 406 893 392 862 406 893 543 1195 553 1217 571 1256 679 1494


Catalog 2011

MODEL

726 Y-STRAINER The Shurt Model 726 Grooved-end

maintenance and is suitable for either vertical

Y-Strainers are designed to strain foreign

or horizontal installation.

matter and debris from piping systems

Standard Screen: 1/16” (1.6mm) perforated

and provide inexpensive protection for

for 2” – 3” sizes and 1/8” (3.2mm) perforated

costly pumps, meters and other pipeline

for 4” – 16”. Other customized screen

components. The Model 726 features a low

perforations are also available upon request.

pressure drop, fast installation, easy C


Size in / mm

Nom. Rating

Working Pressure


2” – 6” Class 150 50 - 150

300 psi @100°F 20 Bar @38°C

EPDM: 230°F / 110°C

8" – 30" Class 125 200 – 750

175 psi @100°F 12 Bar @38°C

C


Pipe OD mm / in 60.3 2.375 73.0 2.875 76.1 3.000 88.9 3.500 114.3 4.500 139.7 5.500 141.3 5.563 168.3 6.625 165.1 6.500 216.3 8.516 219.1 8.625 267.4 10.528 273.0 10.750 318.5 12.539 323.9 12.750 355.6 14.000 406.4 16.000 457.2 18.000 508.0 20.000 558.8 22.000 609.6 24.000 660.4 26.000 711.2 28.000 762.0 30.000

C

Max. Working Pressure A bar / psi mm / in 20 248 300 9.75 20 273 300 10.75 20 273 300 10.75 20 299 300 11.75 20 362 300 14.25 20 419 300 16.50 20 419 300 16.50 20 470 300 18.50 20 470 300 18.50 16 610 232 24.00 16 610 232 24.00 12 686 175 27.00 12 686 175 27.00 12 762 175 30.00 12 762 175 30.00 12 1016 175 40.00 12 1067 175 42.00 12 1232 175 48.50 12 1365 175 53.75 12 1524 175 60.00 12 1626 175 64.00 12 1727 175 68.00 12 1829 175 72.00 12 1905 175 75.00


B A A

A



Nominal Size mm / in 50 2 65 2½ 76.1mm 80 3 100 4 139.7mm 125 5 150 6 165.1mm 200 JIS 200 8 250 JIS 250 10 300 JIS 300 12 350 14 400 16 450 18 500 20 550 22 600 24 650 26 700 28 750 30

B

B

2"-12"

18"-30" Fabricated

14"-16"

Dimensions B C mm / in mm / in 181 116 7.13 4.56 199 122 7.83 4.80 199 122 7.83 4.80 221 129 8.70 5.08 269 168 10.59 6.61 330 258 13.00 10.16 330 258 13.00 10.16 357 219 14.05 8.62 357 219 14.05 8.62 454 284 17.87 11.18 454 284 17.87 11.18 522 320 20.55 12.60 522 320 20.55 12.60 609 366 24.00 14.40 609 366 24.00 14.40 760 480 29.92 18.90 777 483 30.60 19.00 851 711 33.50 28.00 991 813 39.00 32.00 1029 838 40.50 33.00 1067 864 42.00 34.00 1194 965 47.00 38.00 1308 1041 51.50 41.00 1422 1130 56.00 4450

Drain Plug Size mm / in 15 ½ 15 ½ 15 ½ 15 ½ 25 1 25 1 25 1 25 1 25 1 40 1½ 40 1½ 40 1½ 40 1½ 40 1½ 40 1¼ 32 1¼ 32 1¼ 50 2 50 2 50 2 50 2 50 2 50 2 50 2

www.shurt.com

Approx. Weight Kgs / Lb 4.2 9.3 6.0 13.2 6.0 13.2 7.6 16.8 12.0 26.4 22.0 48.4 22.0 48.4 29.7 65.4 29.5 65.0 55.0 121.0 55.0 121.0 83.0 182.6 83.0 182.6 126.0 277.2 126.0 277.2 246.5 543.4 322.0 709.9 375.0 825.0 480.0 1056.0 670.0 1474.0 765.0 1683.0 1020.0 2244.0 1370.0 3014.0 1585.0 3487.0

Catalog 2011

MODEL

728 T-STRAINER Shurt Model 728 Grooved-end

pressure drop, fast installation, easy

T-Strainers are designed to strain foreign

maintenance and is suitable for either vertical

matter and debris from piping systems

or horizontal installation.

and provide inexpensive protection for

Standard Screen: Mesh 12 for 2” – 3” sizes

costly pumps, meters and other pipeline

and mesh 6 for 4” – 14”.

components. The Model 726 features a low


Working Pressure


Class

300 psi @100°F

EPDM: 230°F / 110°C

20 Bar @38°C


150

Plug, H C


B

A

Nominal Size mm / in 50 2 65 2½ 80 3 100 4 125 5 150 6 200 8 250 10 300 12 350 14

Pipe O. D. mm / in 60.3 2.375 73.0 2.875 88.9 3.500 114.3 4.500 141.3 5.563 168.3 6.625 219.1 8.625 273.0 10.750 323.9 12.750 355.6 14.000

Max. Working Pressure A Bar / psi mm / in 20 166 300 6.54 20 191 300 7.50 20 216 300 8.50 20 254 300 10.00 20 279 300 11.00 20 330 300 13.00 20 394 300 15.50 20 457 300 18.00 20 508 300 20.00 20 559 300 22.00

Dimensions B C mm / in mm / in 120 125 4.72 4.92 132 142 5.19 5.59 146 164 5.74 6.45 165 190 6.49 7.48 190 218 7.48 8.58 212 260 8.34 10.23 253 320 9.96 12.60 284 380 11.18 14.96 309 430 12.16 16.92 451 540 17.75 21.25

H (Drain Plug) mm / in 15 ½ 15 ½ 15 ½ 25 1 25 1 25 1 40 1½ 40 1½ 40 1½ 40 1½

Approx. Weight Kgs / Lbs 3.0 6.6 4.0 8.8 6.0 13.2 8.0 17.7 13.0 28.6 20.0 44.0 35.0 77.0 52.0 114.6 72.7 160.25 84.5 186.29

The T-strainer shall be cleaned periodically or before the differential pressure reaches 10 psi.


www.shurt.com


Catalog 2011

MODEL

RCV RISER CHECK VALVE The Model RCV is a grooved-end ductile

and the streamlined body provides for low

iron body check valve, designed for use

friction loss. The valve can be installed in

in the risers of wet type fire protection

the vertical or horizontal position. Valves are

systems. The single clapper design features

tested to UL312.

dual springs for non-slamming operation


Nom. Size

Working Pressure


CWP

2½” – 6” 65 - 150

300 psi @100°F 20 Bar @38°C


*Working pressure is based on connection with roll- or cut-grooved standard wall carbon steel pipe.

A

NPT or BSP Nominal Size mm / in 65 2½ 76.1 mm 80 3 100 4 139.7 mm 125 5 165.1 mm 150 6


Pipe O. D. A mm / in mm / in 73.0 190 2.875 7.48 76.1 190 3.000 7.48 88.9 178 3.500 7.00 114.3 216 4.500 8.50 139.7 330 5.500 13.00 141.3 330 5.563 13.00 165.1 305 6.500 12.00 168.3 305 6.625 12.00


B

Dimensions B Drain NPT or BSP mm / in in 114 1¼ 4.50 114 1¼ 4.50 114 1¼ 4.50 146 2 5.75 210 2 8.25 210 2 8.25 210 2 8.25 210 2 8.25

www.shurt.com

Weight Kgs / Lbs 4.98 10.96 4.98 10.96 4.99 10.98 8.49 18.68 23.34 51.35 23.80 52.36 22.83 50.23 23.10 50.82

Section 5 Threaded Fittings & Welding Outlets Threaded Fittings & Welding Outlets......................................... 92 Threaded Fittings 811 / 812 / 813 / 814 / 815 Elbows, Tees....................................... 93 815 / 816 / 817 / 818 Tee, Cross, Coupling..................................... 94 819 / 820 / 825 / 827 / 831 / 832 Plug, Cap Extension Piece, Hex Bushing, Elbow, Tee...................................................................... 95

830 / 841 Union, Companion Flange................................................. 96 Top Beam Clamp B20 / B24 Beam Clamps................................................................... 96 Welding Outlets 71 Threaded Outlet.............................................................................. 97 72C / 72R Welding Outlet.................................................................. 98

Catalog 2011

Catalog 2011

Threaded Fittings & Welding Outlets Shurt offers a complete range of ductile iron Class 300 threaded fittings in sizes from ½” to 2½”. Shurt ductile iron threaded fittings are 100% air tested underwater to ensure leak-free performance. The Shurt ductile iron fitting series is UL listed and FM approved, making them the right choice for fire protection and other general application services.

Welding Outlets

Pressure-Temperature Rating (ANSI B16.3 & B16.14) Nom. Rating

branch outlet at any desired location along the header pipe. Available in a variety of

½” – 1” : 2000 psi / 140 Bar

Class 300 1¼” – 2” : 1500 psi / 105 Bar

Shurt welding outlets provide an easy

Working Pressure (W.O.G.) Working Pressure @150°F / @65°C Saturated Steam 300 psi (20 Bar)

size and configurations including threaded,

2½”: 1000 psi / 70 Bar

cut grooved and roll grooved ends. Welding

*Proof test pressure: 1.5 times the working pressure, non-shock cold water.

outlets are UL listed and FM approved for fire protection applications.

Pressure-Temperature Rating Unions, Brass to Iron Seat (ANSI B16.39)

Nom.

Rating Class 300

Working Pressure (W.O.G.) Working Pressure @150°F / @65°C

Saturated Steam

600 psi / 42 Bar

300 psi (20 Bar)

*Proof test pressure: 1.5 times the working pressure, non-shock cold water. *Max. Temperature: 450°F (ASME Boiler Code)

Pressure-Temperature Rating Companion Flanges (ANSI B16.42)

Nom.

Rating Class 150


Working Pressure (W.O.G.) Working Pressure @150°F / @65°C

Saturated Steam

250 psi / 17 Bar

150 psi (10 Bar)

Nom.

Rating

Working Pressure (W.O.G.) Working Pressure

Class 300

*Proof test pressure: 1.5 times the working pressure, non-shock cold water.

@150°F / @65°C

Saturated Steam

600 psi / 42 Bar

300 psi (20 Bar)

*Proof test pressure: 1.5 times the working pressure, non-shock cold water. *Burst test pressure: Minimum 3 times the working pressure.

Material: Ductile iron ASTM A536 Gr. 65-45-12 Dimensions: ANSI B16.3 Class 150 except bushings and plugs (B16.14), unions (B16.39) and companion flanges (B16.42) Ductile Iron Class 300 threaded fittings are designed to the same dimensions as that of Class 150 malleable iron fittings. Though due to the superior strength characteristics,

Threads: ANSI B1.20.1 NPT or ISO-7 (BSPT) Finish: Black or electro-zinc plated

ductile Iron fittings carry a much higher pressure rating. Laboratory tests confirm Shurt ductile iron fittings have ed hydrostatic test pressures exceeding 6,000 psi / 414 Bar, which is equal to four times the 1,500 psi /103 Bar as specified by ANSI B16.3 for 1-1/2” – 2” sizes.

General Dimensions

These dimensions apply to all standard fittings, both straight and reducing. For center-to-face dimensions(*), see fitting tables.

E B

H

Pipe H E Size Band O.D. Band Width in in in

½

1.02

0.25

0.43

¾

1.46

0.27

0.50

1

1.77

0.30

0.58

1¼

2.15

0.34

0.67

1½

2.43

0.37

0.70

2

2.96

0.42

0.75

2½

3.59

0.48

0.92

Burst pressure testing of DI threaded fittings (2")



B Thread Length (min.) in

www.shurt.com

MODEL

Catalog 2011

MODEL

811 90° Elbow

814 TEE

A A A A

Nominal Size in ½ ¾ 1 1¼ 1½ 2 2½

A in 1.12 1.31 1.50 1.75 1.94 2.25 2.70

Weight Lbs 0.25 0.35 0.57 0.97 1.17 1.83 3.34

Box Q'ty Pcs 240 120 70 40 30 20 10


A A in 1.12 1.31 1.50 1.75 1.94 2.25 2.70

Weight Lbs 0.31 0.48 0.81 1.28 1.72 2.57 4.44

Box Q'ty Pcs 150 90 60 35 24 12 8

MODEL

812 REDUCING 90˚ ELBOW

MODEL

815 REDUCING TEE

B C A

Nominal Size in ¾ x ½ 1 x ½ 1 x ¾ 1¼ x ½ 1¼ x ¾ 1¼ x 1 1½ x ½ 1½ x ¾ 1½ x 1 1½ x 1¼ 2 x ¾ 2 x 1 2 x 1½ 2½ x 2

A in 1.20 1.26 1.18 1.34 1.45 1.58 1.41 1.52 1.65 1.82 1.60 1.73 2.02 2.39

B in 1.22 1.36 1.45 1.53 1.62 1.67 1.66 1.75 1.80 1.88 1.97 2.02 2.16 2.60

Weight Lbs 0.35 0.46 0.51 0.64 0.68 0.81 0.84 0.90 0.95 1.10 1.19 1.47 1.61 2.93

Box Q'ty Pcs 160 110 90 75 60 55 45 45 40 35 30 25 20 15

MODEL

813 45° Elbow A

A


A in 0.88 0.98 1.12 1.29 1.43 1.68 1.95

Weight Lbs 0.22 0.33 0.55 0.84 0.92 1.63 2.42


Box Q'ty Pcs 250 150 90 50 35 18 12

A Nominal Size in ¾ ¾ ½ ½ 1 ½ 1 ¾ ¾ 1 ½ 1 ¾ ½ ¾ 1 1 1¼ 1¼ ½ 1¼ ¾ 1 ½ ¾ 1 1 1½ ½ 1½ 1¼ ¾ 1 ½ ¾ 1½ 1 1¼ 1 2 1¼ 2 ½ ¾ 1½ 1 1½ 2 2 ½ ¾ 2 1 1¼ 1½ 2½ 2 ¾

B A in 1.20 1.50 1.26 1.37 1.50 1.26 1.37 1.34 1.45 1.58 1.75 1.34 1.45 1.58 1.44 1.50 1.65 1.94 1.41 1.52 1.65 1.41 1.52 1.65 1.82 2.25 2.25 1.49 1.60 1.73 2.02 2.25 1.49 1.60 1.73 1.90 2.02 1.74

B in 1.20 1.36 1.20 1.31 1.45 1.26 1.37 1.26 1.37 1.50 1.67 1.34 1.45 1.58 1.31 1.37 1.50 1.80 1.34 1.45 1.58 1.41 1.52 1.65 1.82 2.02 2.10 1.41 1.52 1.65 1.94 2.16 1.49 1.60 1.73 1.90 2.02 1.60

www.shurt.com

C in 1.22 1.50 1.36 1.45 1.50 1.36 1.45 1.53 1.62 1.67 1.75 1.53 1.62 1.67 1.69 1.75 1.80 1.94 1.66 1.75 1.80 1.66 1.75 1.80 1.88 2.25 2.25 1.88 1.97 2.02 2.16 2.25 1.88 1.97 2.02 2.10 2.16 2.32

Weight Lbs 0.46 0.71 0.59 0.66 0.77 0.64 0.75 0.79 0.88 1.01 1.25 0.84 0.99 1.12 0.92 1.01 1.19 1.54 1.08 1.14 1.39 1.10 1.17 1.36 1.56 2.13 2.22 1.52 1.47 1.63 2.09 2.33 1.56 1.61 1.80 2.09 2.24 2.35

Box Pcs 95 55 80 65 55 65 60 50 50 45 40 45 45 40 40 40 30 30 40 40 30 35 35 30 30 15 15 30 25 20 20 15 20 20 20 20 15 15


MODEL

MODEL

815 BULLHEAD TEE

817 CROSS / REDUCING CROSS B

B C

Catalog 2011

A A A

B

Model 817 Cross Nominal Size in ¾ ¾ 1 1¼ 1 1 1½ 1 1½ 1¼ 1½ 1¼ 2 1¼ 2 1½ 1½ 2 2 2 2½

A in 1.45 1.67 1.80 1.88 1.88 2.10 2.16 2.16 2.60

B in 1.45 1.67 1.80 1.80 1.88 2.10 2.10 2.16 2.60

C in 1.37 1.58 1.65 1.82 1.82 1.90 2.02 2.02 2.39

Weight Lbs 0.66 0.97 1.15 1.43 1.52 1.80 1.94 2.00 3.61

Box Q'ty Pcs 65 45 35 30 30 24 20 20 10

Nominal Size (NPT) in ½ ¾ 1 1¼ 1½ 2

A in 1.12 1.31 1.50 1.75 1.94 2.25

A

B in 1.12 1.31 1.50 1.75 1.94 2.25

Weight Lbs 0.48 0.77 0.95 1.43 1.87 2.86

Box Q'ty Pcs 90 60 45 25 20 10

Weight Lbs 1.25 1.47 1.94

Box Q'ty Pcs 30 24 16

Weight Lbs 0.18 0.26 0.42 0.57 0.77 1.17 2.11

Box Q'ty Pcs 360 200 110 75 60 30 18

A

B

MODEL

816 REDUCING COUPLING

B

Model 817 Reducing Cross Nominal Size (NPT) in 1¼x1¼x1x1 1½x1½x1x1 2 x 2 x 1 x 1

A

Nominal Size in ¾ x ½ 1 x ½ 1 x ¾ 1¼ x ¾ 1¼ x 1 1½ x 1 1½ x 1¼ 2 x 1 2 x 1¼ 2 x 1½ 2½ x 2

A in 1.63 1.69 1.37 2.06 2.06 2.31 2.31 2.81 2.81 2.81 3.25

Wrench Size in 1¼ 1¼ 1½ 1½ --- --- --- --- --- --- ---

Weight Lbs 0.37 0.37 0.48 0.59 0.66 0.84 0.92 1.23 1.28 1.36 2.24

Box Q'ty Pcs 150 140 120 80 60 50 45 35 30 30 18



B in 1.58 1.65 1.73

MODEL

818 STRAIGHT COUPLING

A

Nominal Size (NPT) in ½ ¾ 1 1¼ 1½ 2 2½

94

A in 1.67 1.80 2.02

A in 1.38 1.61 1.77 2.00 2.20 2.60 3.00

Wrench Size in 1⅛ 1⅜ 111/16 2 2¼ 2¾ 3⅜

www.shurt.com

MODEL

Catalog 2011

MODEL

819 PLUG

827 HEX BUSHING A

A

Nominal Size (NPT) in ½ ¾ 1 1¼ 1½ 2

A in 0.93 1.13 1.25 1.36 1.45 1.50

Weight Lbs 0.09 0.18 0.25 0.42 0.59 0.95

Box Q'ty Pcs 500 300 200 110 80 45

Nominal Size in 1 x ½ 1 x ¾ 1¼ x 1 1½ x 1 1½ x 1¼ 2 x 1 2 x 1¼ 2 x 1½

A in 1.06 1.06 1.18 1.26 1.26 1.34 1.34 1.34

Weight Lbs 0.20 0.18 0.29 0.53 0.37 0.75 0.75 0.64

Box Q'ty Pcs 280 280 150 100 100 80 80 80

MODEL

MODEL

831 LONG STREET 90˚ ELBOW

820 CAP A

A B Nominal Size (NPT) in ½ ¾ 1 1¼ 1½ 2 2½

A in 0.89 1.00 1.18 1.32 1.38 1.48 1.77

Weight Lbs 0.14 0.20 0.33 0.46 0.57 0.88 1.54

Box Q'ty Pcs 500 300 180 110 80 45 25

MODEL

Nominal Size in 1 x ½M 1 x 1M

A in 1.50 1.50

B in 3.00 3.00

Weight Lbs 0.66 0.81

Box Q'ty Pcs 80 60

MODEL

825 EXTENSION PIECE

832 LONG STREET TEE C

A

Nominal Size in ½ x 1½L ½ x 2L ¾ x 1½L ¾ x 2L

A A in 1.50 2.00 1.50 2.00

Weight Lbs 0.18 0.22 0.22 0.26


Box Q'ty Pcs 300 250 250 200

Nominal Size in 1 x ½x1M 1 x 1 x 1M

B A in 1.50 1.50

B in 1.40 1.50

C in 3.00 3.00

www.shurt.com

Weight Lbs 0.91 1.03

Box Q’ty Pcs 50 45


MODEL

Catalog 2011

MODEL

830 BRASS SEAT UNION

841 COMPANION FLANGE

The Model 841 is a traditional companion flange used for transition from a flanged to a threaded piping system.

C

A

B D E A

Nominal Size in ½ ¾ 1 1¼ 1½ 2

A in 1.81 1.99 2.17 2.52 2.64 3.15

Weight Lbs 0.46 0.64 1.01 1.45 1.85 2.86

Box Q'ty pcs 110 80 50 35 25 18

Nominal Size in 1 1¼ 1½ 2 2½ 3 4 6 8

A in 4.25 4.62 5.00 6.00 7.00 7.50 9.00 11.00 13.50

B in 0.56 0.62 0.69 0.75 0.88 0.94 0.94 1.00 1.12

C in 1.94 2.31 2.56 3.06 3.56 4.25 5.31 7.56 9.69

D in 0.69 0.81 0.88 1.00 1.12 1.19 1.31 1.56 1.75

E in 3.12 3.50 3.88 4.75 5.50 6.00 7.50 9.50 11.75

Weight pcs 1.54 1.94 2.29 4.18 5.83 6.60 11.75 16.50 25.98

MODEL

B20 STANDARD TOP BEAM CLAMP B24 WIDE MOUTH TOP BEAM CLAMP Size Range: 3/8” and 1/2” rod.

Material: Ductile iron casting with a

Conforms to: Federal Specification WW-H-171 (Type 23), Manufacturers

hardened steel cup-point set screw and lock

Standardization Society ANSI/ MSS-SP-58

nut.

(Type 19 & 23), install in accordance with

Application: Designed for structural

ANSI/ MSS-SP-69. Exceeds requirements

attachment to the top of metal beams,

of NFPA-13.

channel or other structural shapes to

Finish: Black or electro zinc plated.

hanger rod. The universal design allows clamps to be installed in the top or bottom beam position.

C

C

D

D E

E

B

B

A

A

B20

Model No. B20-3 B20-4 B24-3 B24-4


Rod Size A B mm / in mm / in M10 19.1 ⅜ 3/4 M12 19.1 ½ 3/4 M10 28.6 ⅜ 1-1/8 M12 28.6 ½ 1-1/8

Dimensions C D E mm / in mm / in mm / in 12.5 25.4 9.5 0.49 1 3/8 12.5 25.4 9.5 0.49 1 3/8 12.5 25.4 11.1 0.49 1 7/16 12.5 25.4 11.1 0.49 1 7/16


B24 Pipe Size mm / in 20 - 100 ¾ – 4 125, 150, 200 5, 6, 8 20 - 100 ¾ – 4 125, 150, 200 5, 6, 8

Max. Recom. Load Top Bottom Kgs / Lbs Kgs / Lbs 227 114 500 250 432 340 950 750 227 114 500 250 432 340 950 750

www.shurt.com

Weight Per 100 pcs Kgs / Lbs 16.8 37.0 16.0 35.2 19.7 43.3 20.9 46.0

Catalog 2011

MODEL

71 FEMALE THREADED

Outlet Size mm / in

OUTLET FITTING

8 ¼

Model 71 Female Threaded Outlet Fittings are designed to provide a threaded outlet

15 ½

at any desired location along the header. Made of highly weldable SAE-J403 forged steel the Model 71 is designed for single

20 ¾

welding. The Model 71 features a counter bore and a 1.6mm land around the full circumference of the mouth, which helps

25 1

ensure full penetration welds and minimize the likelihood of any burn through or distortion that might be caused by excessive

32 1¼

heat. The Model 71 is UL / cUL listed and FM approved for services up to 300 psi (20 bar).

40 1½

A M

B

50 2

D (Hole dia.) 65 2½ (73.0 OD)

A A

80 3

B M

B

45º

100 4

C

C

1/4" x Flat

Header Size Range in

Outlet OD A mm / in

Outlet Length B mm / in

Counter- bore C mm / in

Make- Hole Saw Max. Hole Up Dia. (Ref.) Dia. (Ref.) M D D mm / in mm / in mm / in

19.1 31.8 10.7 20.5 9.5 1¼ - 8 0.75 1.25 0.42 0.81 ⅜ 1¼ – 1½ 1½ - 2 28.6 25.4 20.6 12.7 17.5 11/16 2 – 2½ 1.13 1.00 0.81 0.50 2½ – 8 1¼ – 1½ 34.9 25.4 26.9 12.7 22.2 1½ - 2 1.37 1.00 1.06 0.50 ⅞ 2 – 2½ 2½ – 8 1¼ – 1½ 1½ - 2 40.0 28.6 31.8 12.7 28.6 2 – 2½ 1.57 1.13 1.25 0.50 1⅛ 2½ – 3 3–4 5–8 1½ - 2 2 – 2½ 48.5 31.8 41.0 12.7 34.9 2½ - 3 1.91 1.25 1.61 0.50 1⅜ 3-4 5-8 2 55.0 31.8 47.0 22.2 41.3 2½ 2.16 1.25 1.85 0.88 1⅝ 3-4 5–8 2½ 3 67.0 38.1 58.6 22.2 54.0 4 2.64 1.50 2.30 0.88 2⅛ 5 6 8 3 4 79.0 44.5 70.1 28.6 63.5 5 3.11 1.76 2.76 1.13 2½ 6 8 4 98.0 53.3 87.0 38.1 79.4 5 3.86 2.10 3.43 1.50 3⅛ 6 8 5 125.2 60.3 113.3 50.8 104.8 6 4.93 2.37 4.46 2.00 4⅛ 8

10.3 13/32 20.6 13/16

25.4 1

31.8 1¼

38.1 1½

44.5 1¾

57.2 2¼

66.7 2⅝

82.6 3¼ 108.0 4¼

Approx. Weight Kgs

Lbs

0.04

0.09

0.07 0.07 0.06 0.05 0.10 0.09 0.09 0.08 0.11 0.11 0.11 0.11 0.11 0.10 0.19 0.19 0.19 0.18 0.18 0.24 0.24 0.22 0.22 0.40 0.39 0.39 0.39 0.38 0.38 0.48 0.38 0.38 0.45 0.49 0.80 0.77 0.77 0.77 1.40 1.32 1.32

0.15 0.15 0.13 0.11 0.22 0.20 0.20 0.18 0.24 0.24 0.24 0.24 0.24 0.22 0.42 0.42 0.42 0.40 0.40 0.53 0.53 0.48 0.48 0.88 0.86 0.86 0.86 0.84 0.84 1.06 0.84 0.84 0.99 1.08 1.76 1.70 1.70 1.70 3.08 2.90 2.90

The precision machined mouth is designed to fit the first listed header size perfectly, and allows only a small gap along the longitudinal centerline of the second listed header size.

Each outlet size shown in the following

the header pipe, which is one size smaller

table fits the same header pipe size. Special

than the regular hole size.

attention is required to the hole size (D) in

A

Outlet Size mm / in

A

B

B

M D (Hole dia.)

C


32 1¼ 40 1½ 50 2 65 2½ (73.0 OD) 80 3 100 4

Header Size Range in 1¼ 1½ 2 2½ 3 4

Outlet OD A mm / in

Outlet Length B mm / in

Counter- bore C mm / in

Make- Up M mm / in

Hole Saw Max. Hole Dia. (Ref.) Dia. (Ref.) D D mm / in mm / in

48.5 1.91 55.0 2.06 67.0 2.64

31.8 1.25 31.8 1.25 38.1 1.50

36.5 1.44 42.5 1.67 54.5 2.15

12.7 0.50 22.2 0.88 22.2 0.88

31.8 1¼ 38.1 1½ 50.8 2

34.9 1⅜ 41.3 1⅝ 54.0 2⅛

79.0 3.11

44.5 1.75

65.2 2.57

28.6 1.13

60.3 2⅜

63.5 2½

98.0 3.86 125.2 4.93

53.3 2.10 63.3 2.37

81.0 3.19 107.0 4.21

38.1 1.50 50.8 2.00

76.1 3 101.6 4

79.4 3⅛ 104.8 4⅛

www.shurt.com

Approx. Weight Kgs

Lbs

0.19

0.42

0.21

0.46

0.34

0.75

0.49

1.08

0.80

1.76

1.40

3.08


Catalog 2011

MODEL

72C CUT GROOVED

WELDING OUTLET

Model 72C Cut Grooved Outlet Fittings are

Outlet Size mm/in

50 2

designed to provide a cut grooved outlet at any desired location along the header. Made of standard wall (sch.40) pipe, the Model 72C is recommended for use with Sch. 40

65 2½

header pipes. The weld end is provided with a 1.6mm land around the full circumference to assure a one- full penetration weld. The 72C fittings are recommended for

80 3

services up to 20 bar (300 psi).

100 4 150 6 200 8

Run Pipe A B in mm/in mm/in 2 2½ 3 4 5 6 8 2½ 4 5 6 8 3 4 5 6 8 4 5 6 8 6 8 8 10

Dimensions L mm/in

W mm/in

G mm/in

Approx. Weight Kgs/Lbs

60.3 2.375

76.2 3.000

15.88 0.625

7.95 0.312

57.15 2.250

0.40 0.88

73.0 2.875

76.2 3.000

15.88 0.625

7.95 0.312

69.09 2.722

0.50 1.10

88.9 3.500

76.2 3000

15.88 0.625

7.95 0.312

84.94 3.346

0.91 2.00

114.3 4.500

101.6 4.000

15.88 0.625

9.53 0.375

110.08 4.337

1.73 3.80

168.3 6.625 219.1 8.625

101.6 4.000 101.6 4.000

15.88 0.625 19.05 0.750

9.53 0.375 11.13 0.438

163.96 6.460 214.40 8.440

3.18 7.00 4.32 9.50

A L G

W B

45˚±1.5˚ 1.6mm land

MODEL

72R ROLL-GROOVED

Outlet Size mm/in

32 1¼

WELDING OUTLET

Model 72R Roll Grooved Outlet Fittings are designed to provide a roll grooved outlet

40 1½

at any desired location along the header. Made of Sch. 10 pipe, the 72R R-Let is recommended for use with light wall pipes to minimize the likelihood of burn-through and

50 2

or distortion of the header pipe. The 72R fittings are recommended for services up to 20 bar (300 psi).

65 2½

76.1mm

A L G WB

100 4

45˚


80 3


Run Pipe A B in mm/in mm/in 1¼ 1½ 2 2½ 3 4 5-8 1½ 2 2½ 3 4 5-8 2 2½ 3 4 5 6 8 2½ 3 4 5 6 8 2½ 3 4 5 6 8 3 4 5 6 8 4 5 6 8

Dimensions

Approx.

L mm/in

W mm/in

G mm/in

Weight Kgs/Lbs

42.2 1.660

76.2 3.000

15.88 0.625

7.14 0.281

38.99 1.535

0.15 0.33

48.3 1.900

76.2 3.000

15.88 0.625

7.14 0.281

45.09 1.775

0.18 0.40

60.3 2.375

76.2 3.000

15.88 0.625

8.74 0.344

57.15 2.250

0.29 0.64

73.0 2.875

76.2 3.000

15.88 0.625

8.74 0.344

69.09 27.20

0.51 1.12

76.1 3.000

76.2 3.000

15.88 0.625

8.74 0.344

72.26 2.845

0.51 1.12

88.9 3.500

76.2 3.000

15.88 0.625

8.74 0.344

84.94 3.440

0.56 1.23

114.3 4.500

114.3 4.500

15.88 0.625

8.74 0.344

110.08 4.314

0.94 2.07

www.shurt.com

Section 6 Ring t, Shouldered and Plain End Couplings Ring t, Shouldered and Plain End Couplings............................... 100 Ring t Couplings

R-88 Ring t Coupling.................................................................. 101 R-88 & R-88N 8" ~ 26" Ring t Coupling................................... 102 R-88 28" ~ 96" Large Diameter Ring t Coupling........................ 103 RH-1000 1000 psi Ring t Coupling........................................... 104 RX-3000 3000 psi Ring t Coupling............................................ 104 RX-3770 3770 psi Ring t Coupling............................................ 105

Ring t Fittings

RJ-10 / RJ-11 / RJ-20 / RJ-60 Elbows, Tee & Cap.................... 106 RJ-21 / RJ-50 / RJ-51 / RJ-70 Reducing Tee, Concentric &

Eccentric Reducer, Flange................................................................. 107 Shouldered Couplings........................................................................... 108

S35 Shouldered Flexible Coupling.................................................... 109 SD-28 Shouldered Toggle Coupling................................................. 109

Plain-End Coupling

79 Wildcat™ Coupling........................................................................110

Catalog 2011

Catalog 2011

Ring t, Shouldered and Plain End Couplings Shurt ring t, shouldered and plain end couplings are non-grooved mechanical pipe ing components and excellent alternatives where pipe is difficult to groove or when grooving is not the preferred method. The processing of a roll groove on pipe

Ring t Coupling

becomes more difficult as the pipe O.D. and or wall thickness increases. Roll grooving pipe larger than 14” (350 mm) requires proper tools and equipment. Pipe having a wall thickness greater than .375” (9.5 mm) may not be practical to roll groove.

Bolts & Nuts

The Shurt ring t

coupling provides a much more secure t than a comparable roll-grooved system, simply because the area of the rings is much greater than that of the roll-groove profile. In addition, the

Weld Ring

Housing Segment

welded rings are able to withstand 2 - 3 times the shearing forces of roll grooves. High pressure couplings up to 3770 psi (260 bar) are available. Gasket

Factory Supplied Weld Rings

Shouldered Coupling

The Shurt shouldered

#R-88 Ring t Coupling

Housing Segment

Type A Weld-on Ring

piping system is a classic and versatile pipe ing method which

utilizes Type A weld-on rings. Shurt shouldered couplings are

Gasket

widely used in irrigation, dewatering on construction sites, and other installations. Bolt & Nut

#S35 Shouldered Coupling

Plain-end Coupling

The Shurt plain-end

coupling securely grips the pipe with its built-in case hardened

Hardened Steel Jaws Gasket

jaws incorporated within heavy duty housing segments and heavy

duty bolts and nuts. The Shurt Model 79 ‘Wildcat’ coupling is designed to plain-end or beveled-end carbon steel pipe without roll-grooving, welding or threading. The Model 79 plain-end coupling can be used for mining, process piping, manifold piping, and oil field services.

Housing Segment Bolt & Nut

Steel Pipe 2" – 16" (Hardness HB 150 max.)

#79 Plain-end Coupling



www.shurt.com

Catalog 2011

MODEL

R-88 RING T COUPLING The Shurt Model R-88 Ring t

The R-88 Coupling can also be used on

Coupling is an ideal pipe ing method

stainless steel pipe with optional weld rings

when pipe is difficult to groove or when

available in compatible stainless steel

grooving is not the preferred ing method.

grades. Check with Shurt for details and

Available in sizes 8” to 96” the R-88 offers

availability.

ease of use and excellent performance. The Shurt Model R-88 Ring t

Typical applications • Water & Waste Water Treatment Plants

Coupling is supplied with a pair of factory

• Mining & Tunnel Boring

supplied weld rings. For installation weld

• Pulp & Paper

a factory-supplied weld ring on each pipe

• Hydroelectric Plants

end to be connected, next mount the rubber

• Co-Gen Electric Plants

gasket over the pipe ends, place coupling

• Food & Beverage

segments over the gasket and fasten the

• Compressed Air

bolts and nuts. The Shurt R-88 Ring t Coupling is considered a shoulder coupling with the factory supplied weld rings serving as the t shoulders. The R-88’s performance standards meet and or exceed the requirements of ASTM F1476 and AWWA C606. The factory supplied weld rings offer a much more economical and convenient alternative to traditional shoulder rings, such as Type A, B, C, D, E, and G rings.

Max. Internal Service Pressures of Carbon Steel Pipe ASTM A53 Gr. B

When deg a piping system you must select pipe with the appropriate wall thickness to correspond with the intended working pressure of the system. The table lists design working pressure by the pipe wall schedule, XS, STD and LW, of representative ASTM A53 Gr. B carbon steel pipe calculated in accordance with the formula stipulated in ASME B31.1 Power Piping 104.1. P = Where:

2SE (tm-A) Do - 2y (tm - A)

P = Maximum internal service pressure (psi) SE = Allowable stress (psi) (ASTM A53 Gr. B = 15,000 psi) tm = Minimum pipe wall thickness (inch) (87.5% of nominal wall thickness) Do = Outside diameter of pipe (inch) y = A coefficient (For ferritic steels 600°F or below = 0.4) A = Additional thickness (inch) (A = 0)

Max. Internal Service Pressures of Carbon Steel Pipe ASTM A53 Gr. B Unit: psi Nom. Size in 8 10 12 14 16 18 20 24 26 28 30 32 34 36 38 40 42 44 48 52 54 56 60

XS 0.5" 1586 1262 1058 962 839 744 668 555 512 475 443 415 390 368 349 331 315 301 275 254 245 236 220

STD 0.375"* 1006 913 788 717 625 555 499 415 382 355 331 310 292 275 261 248 236 225 206 190 183 177 165

LW 0.25"/0.312"^ 777 621 522 475 415 368 331 275 318 295 275 258 242 229 217 206 187

*8": 0.322", ^ 8” ~ 24”: 0.25”, 26” ~ 42”: 0.312”


www.shurt.com


Catalog 2011

MODEL

R-88 RING T COUPLING The Shurt Model R-88 Ring t Coupling is available in sizes from 8”/200mm. Sizes 14”/350mm to 24”/600mm are now available either in a two-segment style (R-88N) or multi-segment style (R-88). The two-segment style offers a easier and faster installation.

Pressure-Temperature Rating Size Nom. Working Pressure in / mm Rating (STD)


8” – 24”

Class

400 psi @100°F

EPDM: 230°F / 110°C

200 - 600

250

28 Bar @38°C


*Working pressure is based on standard wall carbon steel pipe. *Proof test pressure: 1.5 times the working pressure, non-shock cold water. *Burst pressure is engineered minimum 3 times the working pressure for sizes up to 12" (300mm) and 2 times for sizes up to 24" (600mm).

R-88N Size: 24"

R-88 Size: 12"

B

C

A

A 28" R-88 coupling installed in a chill water system Max. Working Pressure Nominal Pipe Rings both sides fully welded Size OD XS (.500”) STD (.375”) LW (.312”) A mm / in mm / in Bar / psi Bar / psi Bar / psi mm / in 200 219.1 40 28 28 256 8 8.625 600 400 400 10.08 250 273.0 40 28 28 312 10 10.750 600 400 400 12.29 300 323.9 40 28 28 374 12 12.750 600 400 400 14.72 216.3 40 28 28 253 200JIS 8.516 600 400 400 9.96 267.4 40 28 28 306 250JIS 10.528 600 400 400 12.05 318.5 40 28 28 369 300JIS 12.539 600 400 400 14.53 350 (R-88N) 355.6 40 28 24 411 14 14.000 600 400 350 16.18 400 (R-88N) 406.4 35 28 24 461 16 16.000 500 400 350 18.15 450 (R-88N) 457.2 35 28 24 511 18 18.000 500 400 350 20.12 500(R-88N) 508.0 35 28 20 591 20 20.000 500 400 300 23.25 600 (R-88N) 609.6 35 28 17 702 24 24.000 500 400 250 27.63

O.D.



L

E

8" ~ 24" (R-88 & R-88N)

Dimensions Bolt Size B C mm / in mm / in No. mm / in 330 79 2 ¾ x 4¾ 13.00 3.11 386 83 2 ¾ x 4¾ 15.20 3.25 455 86 2 ⅞ x 6½ 17.90 3.39 327 79 2 M 20 x 120 12.87 3.11 380 83 2 M 20 x 120 14.96 3.25 450 86 2 M 20 x 120 17.72 3.39 380 98 M22 4 14.96 3.86 ⅞ 422 98 M22 4 16.61 3.86 ⅞ 489 105 M24 4 19.25 4.14 1 665 116 M24 4 26.18 4.56 1 762 123 M22 4 30.0 4.84 ⅞

Sealing Surface L mm / in 23 0.91 23 0.91 26 1.02 23 0.91 23 0.91 26 1.02 26 1.02 26 1.02 30 1.18 30 1.18 30 1.18

Ring Size R mm / in 6 ¼ 6 ¼ 8 5/16 6 ¼ 6 ¼ 8 5/16 8 5/16 8 5/16 12* ½ 12 ½ 12 ½

R-88N is a two-segment type coupling. Dimensions are subject to change without notice. Other sizes are available on request. *10mm shouldered rings are acceptable.

102

R

www.shurt.com

Separation E (max) mm / in 4.8 0.19 4.8 0.19 4.8 0.19 4.8 0.19 4.8 0.19 4.8 0.19 9.5 0.375 9.5 0.375 9.5 0.375 9.5 0.375 9.5 0.375

Weight Kgs / Lbs 7.6 16.8 10.1 22.2 14.0 30.8 8.0 17.6 10.0 22.0 14.8 32.6 17.4 38.3 18.7 41.1 23.1 50.8 38.2 84.0 49.7 109.3

Catalog 2011

MODEL

R-88 RING T COUPLING Large diameter

The Shurt Model R-88 Ring t

segments depending on the size and feature

Coupling is available in sizes 28”/700mm

two bolts at each t segment to ensure a

to 96" / 2400mm. The larger diameter

positive connection.

couplings are comprised of 4 to 8 housing Pressure-Temperature Rating Size Nom. Rating 26” - 36“ Class 150 650 - 900 38” – 96” Class 125 950 - 2400

Working Pressure (STD)




O.D.

R

R-88 Size: 48"

L

E

*Working pressure is based on standard wall carbon steel pipe. *Proof test pressure: 1.5 times the working pressure, non-shock cold water. *Burst pressure is engineered minimum 2 times for the listed working pressure.

B

C

C

B

B

C

A A

A

28" ~ 38"

26"

Max. Working Pressure Nominal Pipe Rings both sides fully welded Size OD XS (.500”) STD (.375”) LW (.312”) A mm / in mm / in Bar / psi Bar / psi Bar / psi mm / in 650 660.4 28 20 17 726 26 26.000 400 300 250 28.58 700 711.2 28 20 17 806 28 28.000 400 300 250 31.75 750 762.0 28 20 17 857 30 30.000 400 300 250 33.75 800 812.8 28 20 17 908 32 32.000 400 300 250 35.75 850 863.4 24 20 14 959 34 34.000 350 300 200 37.75 900 914.4 24 20 14 1010 36 36.000 350 300 200 39.75 950 965.2 20 16 12 1060 38 38.000 300 232 175 41.75 1000 1016.0 20 16 12 1135 40 40.000 300 232 175 44.69 1050 1066.8 20 16 12 1186 42 42.000 300 232 175 46.70 1100 1117.6 20 16 12 1236 44 44.000 300 232 175 48.66 1200 1219.2 20 16 --- 1338 48 48.000 300 232 --- 52.68 1300 1320.8 16 12 --- 1555 52 52.000 232 175 --- 61.25 1350 1371.6 16 12 --- 1660 54 54.000 232 175 --- 63.25 1400 1422.4 16 12 --- 1660 56 56.000 232 175 --- 65.38 1500 1524.0 16 12 --- 1762 60 60.000 232 175 --- 69.38 1650 1676.4 12 8.6 --- 1932 66 66.000 175 125 --- 76.00 1700 1727.2 12 8.6 --- 1994 68 68.000 175 125 --- 78.50 1800 1828.8 10 8.6 --- 2095 72 72.000 150 125 --- 82.50 2100 2133.6 8.6 7 --- 2406 84 84.000 125 100 --- 94.75 2400 2438.4 8.6 7 --- 2711 96 96.000 125 100 --- 106.75

40" ~ 96" Dimensions Bolt Size B C mm / in mm / in No. mm / in 815 122 8 ⅞x4 32.09 4.80 902 171 12 ⅞x4 35.50 6.73 955 171 12 1 x 3½ 37.60 6.73 1003 171 12 1 x 3½ 39.50 6.73 1054 171 12 1 x 3½ 41.50 6.73 1103 171 12 1 x 3½ 43.50 6.73 1156 171 12 1 x 3½ 45.50 6.73 1229 198 16 1 x 3½ 48.39 7.80 1280 198 16 1¼ x 5 50.39 7.80 1318 198 16 1¼ x 5 51.89 7.80 1420 198 16 1 x 3½ 55.91 7.80 1539 198 16 1¼ x 5 60.60 7.80 1590 198 16 1¼ x 5 62.60 7.80 1641 198 16 1¼ x 5 64.60 7.80 1742 198 16 1¼ x 5 68.60 7.80 1925 216 16 1½ x 5 75.79 8.00 1976 216 16 1½ x 5 77.79 8.00 2078 216 16 1½ x 5 81.81 8.00 2383 216 16 1½ x 5 93.81 8.00 2662 216 16 1½ x 5 105.79 8.00

Sealing Surface L mm / in 30 1.18 50 2.00 50 2.00 50 2.00 50 2.00 50 2.00 50 2.00 60 2.37 60 2.37 60 2.37 60 2.37 60 2.37 60 2.37 60 2.37 60 2.37 60 2.37 60 2.37 60 2.37 60 2.37 60 2.37

Ring Size R mm / in 12.7 1/2 12.7 1/2 12.7 1/2 12.7 1/2 12.7 1/2 12.7 1/2 12.7 1/2 15.9 5/8 15.9 5/8 15.9 5/8 15.9 5/8 15.9 5/8 15.9 5/8 15.9 5/8 15.9 5/8 19.1 3/4 19.1 3/4 19.1 3/4 19.1 3/4 19.1 3/4

Separation E (max) mm / in 9.5 0.375 12.7 0.50 12.7 0.50 12.7 0.50 12.7 0.50 12.7 0.50 12.7 0.50 15.9 0.625 15.9 0.625 15.9 0.625 15.9 0.625 15.9 0.625 15.9 0.625 15.9 0.625 15.9 0.625 19.1 0.75 19.1 0.75 19.1 0.75 19.1 0.75 19.1 0.75

Weight Kgs / Lbs 59.0 130.0 101.0 222.2 99.5 218.9 102.2 225.4 115.0 253.0 111.6 246.0 125.0 275.0 141.0 310.2 148.6 326.9 156.0 343.2 211.8 466.7 206.0 453.2 214.6 472.1 222.0 488.2 244.2 537.2 278.4 612.5 357.0 785.4 335.3 737.7 354.7 780.3 374.2 823.2

Dimensions are subject to change without notice. Other sizes are available on request.


www.shurt.com


Catalog 2011

MODEL

RH-1000 1000 PSI RING T COUPLING The Shurt Model RH-1000 coupling is a

and nuts which provide a fully restrained

high pressure ring t coupling for use with

t and a maximum working pressure of

Sch. 40, Sch. 80 and heavier wall carbon

1,000 psi (70 Bar) depending on the pipe

steel pipe.

used.

The coupling is comprised of two ductile iron

Two steel weld rings are factory supplied

heavy-wall housings, rubber gasket (EPDM

with the coupling. Steel rings must always

or Nitrile) and two heat-treated track bolts

be fully welded on both sides.


Nom. Rating

Class 400



1000 psi @100°F 70 Bar @38°C


B



Pipe OD mm / in 219.1 8.625 273.0 10.750 323.9 12.750

Max. Working Pressure A Bar / PSI mm / in 70 282 1000 11.10 70 340 1000 13.32 70 415 1000 16.33

C

R

A

L

E

Pipe O.D.

Dimensionsl B mm / in 372 14.65 430 16.93 510 20.07

Bolt / Nut Pipe-end Preparation C Size Deflection R L E (max) mm / in No. in ( ° ) mm / in mm / in mm / in 98 12 25 3.2 2 1" x 140 0° – 18' 3.86 0.47 1 0.13 108 12 25 3.2 2 1" x 165 0° – 38' 4.25 0.47 1 0.13 106 12 25 3.2 2 1" x 165 0° – 32' 4.17 0.47 1 0.13

Weight Kgs / Lbs 18.1 39.8 26.0 57.2 33.0 72.6

*Bolt & nuts are UNC threaded.

MODEL

RX-3000 3000 PSI RING T COUPLING The Shurt Model RX-3000 coupling is

and nuts which provide a fully restrained

a high pressure ring t coupling for use

t and a maximum working pressure up to

with Sch. 80, 120 and heavier wall carbon

3,000 psi (210 Bar) depending on the pipe

steel pipe.

used.

The coupling is comprised of two ductile iron

Two steel weld rings are factory supplied

heavy-wall housings, rubber gasket (EPDM

with the coupling. Steel rings must always

or Nitrile) and four heat-treated track bolts

be fully welded on both sides.


Nom. Rating

Class 1500

Working Pressure


3000 psi @100°F 210 Bar @38°C


B

A

*Working pressure is based on API 5L X65 line pipe. *Proof test pressure: 1.5 times the working pressure, non-shock cold water. *Burst pressure is engineered minimum 2 times the working pressure.


Pipe OD mm / in 219.1 8.625 273.0 10.748 323.9 12.752

Max. Working Pressure A Bar / PSI mm / in 210 300 3000 11.81 210 380 3000 14.96 210 470 3000 18.5

C R

L

E

Pipe O.D.

Dimensions Bolt / Nut* Pipe-end Preparation B C Size R L E mm / in mm / in No. in mm / in mm / in mm / in 394 148 12 31 3 2 1⅛ x 130 15.51 5.83 0.472 1.22 ⅛ 481 152 16 31 3 4 1¼ x 165 18.93 5.98 0.63 1.22 ⅛ 572 173 16 31 3 4 1½" x 160 22.48 6.81 0.63 1.22 ⅛

*Bolt & nuts are UNC threaded. @½” (12.7mm) and ⅝” (15.9mm) steel rings are also available upon request.



www.shurt.com

Weight Kgs / Lbs 35.87 78.92 52.78 116.36 96.24 212.27

Catalog 2011

MODEL

RX-3770 3770 PSI RING T COUPLING The Shurt Model RX-3770 Ring t

iron heavy-wall housing segments, rubber

Coupling is designed to provide a fully

gasket (EPDM) and four heat-treated track

restrained t for use with extra-strong

bolts and nuts. Two steel weld rings are

carbon steel pipe including API 5L Grade

factory supplied with a coupling. Steel rings

X65 line pipe.

shall always be fully welded on both sides.

The coupling is comprised of two ductile


Nom. Rating

Class 2000

Working Pressure


3770 psi @100°F 260 Bar @38°C


B

C

R

*Working pressure is based on API 5L X65 line pipe. *Proof test pressure: 1.5 times the working pressure, non-shock cold water. *Burst pressure is engineered minimum 2 times the working pressure.

A

Dimensions Bolt / Nut* Pipe-end Preparation B C Size R L E mm / in mm / in No. in mm / in mm / in mm / in 321 149 12 31 5 4 ⅞" x 165 12.64 5.87 0.472 1.22 0.20 414 175 16 38 5 4 1¼" x 165 16.30 6.89 0.625 1.50 0.20 505 188 19 38 5 4 1½" x 175 19.88 7.40 0.750 1.50 0.20 587 219 22 38 6 4 1½" x 175 23.10 8.63 0.875 1.50 0.24

Nominal Size mm / in 150 6 200 8 250 10 300 12

Pipe OD mm / in 168.3 6.625 219.1 8.625 273.0 10.750 323.9 12.750

Max. Working Pressure A Bar / PSI mm / in 260 260 3770 10.24 260 329 3770 12.95 260 404 3770 15.90 260 482 3770 19.0

L E

Weight Kgs / Lbs 27.7 61.2 49.9 110.0 79.2 174.5 112.3 247.1

*Bolt & nuts are UNC threaded.

Proof and burst pressure testing


www.shurt.com


RING T FITTINGS

Catalog 2011

MODEL

RJ-10 90° elbow RJ-11 45° elbow RJ-20 TEE RJ-60 CAP Shurt offers a full range of ring t

or wrought carbon steel.

fittings for use with Model R-88 ring t

• Larger sizes are made of carbon steel

couplings.

standard weight pipe, ASTM A53 Gr. B

• 8” - 24” (200mm – 600mm) Models RJ-10,

or equivalent, or fabricated from wrought

RJ-11 & RJ-60 and sizes 8” – 16” (200mm –

carbon steel of the equivalent properties.

400mm) Model RJ-20 are available either in

• Other configurations are also available

cast ductile iron to ASTM A536 Gr. 65-45-12

upon request. Shurt for details.

C-E

C-E

C-E

C-E

C-E

Nominal Size mm / in 200 8 250 10 300 12 200JIS 250JIS 300JIS 350 14 400 16 450 18 500 20 600 24 650 26 700 28 750 30 800 32 850 34 900 36 1000 40 1050 42 1100 44 1200 48


Pipe OD mm / in 219.1 8.625 273.0 10.750 323.9 12.750 216.3 8.516 267.4 10.528 318.5 12.539 355.6 14.000 406.4 16.000 457.2 18.000 508.0 20.000 609.6 24.000 660.4 26.000 711.2 28.000 76.20 30.000 812.8 32.000 863.4 34.000 914.4 36.000 1016.0 40.000 1066.8 42.000 1117.6 44.000 1219.2 48.000

RJ-10 90° Elbow C - E Weight mm / in Kgs / Lbs 197 13.0 7.75 28.6 229 25.0 9.00 55.0 254 35.0 10.00 77.0 197 13.0 7.75 28.6 229 25.0 9.00 55.0 254 35.0 10.00 77.0 280 37.0 11.00 81.4 305 45.0 12.00 99.0 394 95.0 15.50 209.0 438 138.0 17.25 203.6 508 220.0 20.00 485.0 991 237.0 39.00 521.0 1067 275.0 42.00 605.0 1143 316.0 45.00 695.0 1219 360.0 48.00 792.0 1295 407.0 51.00 895.0 1372 457.0 54.00 1005.0 1524 564.0 60.00 1241.0 1600 622.0 63.00 1368.0 1676 683.0 66.00 1503.0 1829 814.0 72.00 1790.0


RJ-10

RJ-11 45° Elbow C - E Weight mm / in Kgs / Lbs 108 9.5 4.25 20.9 121 18.0 4.75 39.6 133 23.0 5.25 50.6 108 9.5 4.25 20.9 121 18.0 4.75 39.6 133 23.0 5.25 50.6 152 24.0 6.00 52.8 184 46.0 7.25 101.2 208 48.0 8.00 105.6 229 50.0 9.00 110.0 280 80.0 11.00 176.0 406 119.0 16.00 262.0 438 138.0 17.25 304.0 480 158.0 18.50 348.0 502 180.0 19.75 396.0 533 204.0 21.00 449.0 565 229.0 22.25 504.0 632 282.0 24.88 620.0 660 311.0 26.00 684.0 696 342.0 27.39 752.0 759 407.0 29.88 895.0

RJ-11

RJ-20

RJ-20 Tee C - E Weight mm / in Kgs / Lbs 197 21.0 7.75 46.2 229 33.0 9.00 72.6 254 47.0 10.00 103.4 197 21.0 7.75 46.2 229 33.0 9.00 72.6 254 47.0 10.00 103.4 280 54.0 11.00 118.8 305 70.0 12.00 154.0 394 122.0 15.50 268.0 438 153.0 17.25 337.0 508 212.0 20.00 466.0 572 348.0 22.50 766.0 597 392.0 23.50 862.0 635 451.0 25.00 992.0 673 516.0 26.50 1135.0 711 584.0 28.00 1285.0 762 657.0 30.00 1445.0 838 814.0 33.00 1790.0 889 837.0 35.00 1841.0 914 943.0 36.00 2075.0 1016 1131.0 40.00 2488.0

www.shurt.com

E-E

RJ-60

RJ-60 Cap E - E Weight mm / in Kgs / Lbs 76 5.5 3.00 12.1 76 6.0 3.00 13.2 76 8.0 3.00 17.6 76 5.5 3.00 12.1 76 6.0 3.00 13.2 76 8.0 3.00 17.6 102 12.0 4.00 26.4 102 15.0 4.00 33.0 127 21.0 5.00 46.2 152 26.0 6.00 57.2 152 35.0 6.00 77.0 267 50.0 10.50 110.0 267 56.0 10.50 123.0 267 62.0 10.50 136.0 267 113.0 10.50 248.6 267 75.0 10.50 165.0 267 152.0 10.50 334.4 305 102.0 12.00 224.0 305 110.0 12.00 242.0 343 126.0 13.50 277.0 343 143.0 13.50 315.0

RING T FITTINGS

Catalog 2011

MODEL

RJ-21 REDUCING TEE RJ-50 CONCENTRIC REDUCER

RJ-51 ECCENTRIC REDUCER C-E

C-E

E-E

E-E

RJ-21

RJ-50

RJ-51

RJ-21 Reducing Tee C - E Weight mm / in Kgs / Lbs 279 66.0 11.00 145.0 305 78.0 12.00 172.0 305 80.0 12.00 176.0 394 112.0 15.50 246.0 394 115.0 15.50 253.0 394 120.0 15.50 264.0 438 135.0 17.25 297.0 438 138.0 17.25 304.0 438 144.0 17.25 317.0 438 149.0 17.25 328.0 508 180.0 20.00 396.0 508 185.0 20.00 407.0 508 190.0 20.00 418.0 508 197.0 20.00 433.0 508 202.0 20.00 444.0

RJ-50 Conc. Reducer E - E Weight mm / in Kgs / Lbs 203* 23.0 8.00 51.0 229* 29.0 9.00 64.0 229* 29.0 9.00 64.0 241* 33.0 9.50 72.6 381 36.0 15.00 79.0 381 36.0 15.00 79.0 254* 43.0 10.00 95.0 508 45.0 20.0 99.0 254 46.0 10.00 101.0 508 58.0 20.00 128.0 305* 70.0 12.00 154.0 508 70.0 20.00 154.0 305* 70.0 12.00 154.0 508 70.0 20.00 154.0 305* 71.0 12.00 156.0

RJ-51 Ecc. Reducer E - E Weight mm / in Kgs / Lbs 203* 23.0 8.00 51.0 229* 29.0 9.00 64.0 229* 29.0 9.00 64.0 241* 35.0 9.50 78.0 381 36.0 15.00 79.0 381 36.0 15.00 79.0 254* 43.0 10.00 95.0 508 45.0 20.0 99.0 254 46.0 10.00 101.0 508 58.0 20.00 128.0 305* 70.0 12.00 154.0 508 70.0 20.00 154.0 305* 70.0 12.00 154.0 508 70.0 20.00 154.0 305* 71.0 12.00 156.0

Nominal Size mm / in 350 x 300 14 x 12 400 x 300 16 x12 400 x 350 16 x 14 450 x 300 18 x 12 450 x 350 18 x 14 450 x 400 18 x 16 500 x 300 20 x 12 500 x 350 20 x 14 500 x 400 20 x 16 500 x 450 20 x 18 600 x 300 24 x 12 600 x 350 24 x 14 600 x 400 24 x 16 600 x 450 24 x 18 600 x 500 24 x 20

Pipe OD mm / in 355.6 x 323.9 14.000 x 12.750 406.4 x 323.9 16.000 x 12.750 406.4 x 355.6 16.000 x 14.000 457.2 x 323.9 18.000 x 12.750 457.2 x 355.6 18.000 x 14.000 457.2 x 406.4 18.000 x 16.000 508.0 x 323.9 20.000 x 12.750 508.0 x 355.6 20.000 x 14.000 508.0 x 406.4 20.000 x 16.000 508.0 x 457.2 20.000 x 18.000 609.6 x 323.9 24.000 x 12.750 609.6 x 355.6 24.000 x 14.000 609.6 x 406.4 24.000 x 16.000 609.6 x 457.2 24.000 x 18.000 609.6 x 508.0 24.000 x 20.000

Concentric reducers marked (*) are made of ductile iron.

MODEL

RJ-70 FLANGE ADAPTER

E-E RJ-70


Nominal Size mm / in 200 8 250 10 300 12 350 14 400 16 450 18 500 20 600 24

Pipe O.D. mm / in 219.1 8.625 273.0 10.750 323.9 12.750 355.6 14.000 406.4 16.000 457.2 18.000 508.0 20.000 609.6 24.000

RJ-70 Flange Adapter E - E Weight mm / in Kgs / Lbs 152 20.4 6 44.9 203 30.5 8 67.1 203 44.6 8 98.1 203 54.0 8.00 118.8 203 66.8 8.00 147.0 203 65.0 8.00 143.0 203 77.0 8.00 169.4 203 130.4 8.00 286.9

www.shurt.com


Catalog 2011

Shurt Shouldered Piping System The Shurt shouldered piping system is a classic and versatile piping method used for a wide range of applications including irrigation, dewatering on construction sites,

Type A Weld-on Ring

Housing Segment

and other installations, etc. The shouldered system features full flow characteristics, provides speed and ease of installation,

Gasket

and proven reliability. The system provides for limited expansion and contraction and accommodates some linear and angular movement. Each t is a union.

The Shurt shouldered piping system

Bolt & Nut

utilizes Type A weld-on rings, manufactured from mild steel or material compatible to pipe end used.

Shoulder Dimensions

L

E

utilizes Type A weld-on rings, manufactured

øD1

The Shurt shouldered piping system L 3

from mild steel or material compatible to

øD2

( Type A Weld-on Rings )

pipe end used. Type A rings are suitable for services up to maximum 40 bar / 600 psi for sizes up to 100mm / 4” and 28 bar / 400 psi for 125mm / 5” through 200mm / 8”.



Nominal Size mm/in 50 2 80 3 100 4 150 6 150 6 200 8

Pipe OD D1 mm/in 60.3 2.375 88.9 3.500 114.3 4.500 165.1 6.500 168.3 6.625 219.1 8.625

Shoulder Diameter D2 mm/in 66.5 2.62 97.0 3.82 122.0 4.80 174.5 6.87 178.0 7.00 232.0 9.13

Shoulder Length L mm/in 16.0 0.63 16.0 0.63 17.5 0.69 17.5 0.69 17.5 0.69 20.6 0.81

www.shurt.com

Nominal Gap E mm/in 3.2 0.13 3.2 0.13 3.2 0.13 3.2 0.13 3.2 0.13 3.2 0.13

Catalog 2011

MODEL

S35 Shouldered FLEXIBLE COUPLING The Shurt Model S35 coupling is a

of ductile iron to ASTM A536 Gr. 65-45-12

flexible type shouldered coupling for general

and or A395 Gr. 65-45-15 and are normally

applications for use on Type A shouldered

supplied in hot-dip galvanized. The standard

pipe ends. The housing segments are made

rubber gasket is Grade T Nitrile.


Nom. Rating

Class 150



300 psi @100°F 20 Bar @38°C


A



Pipe OD mm / in 60.3 2.375 88.9 3.500 114.3 4.500 165.1 6.500 168.3 6.625 219.1 8.625

C

B

Working Pressure A Bar / PSI mm / in 20 99.0 300 3.90 20 129.0 300 5.08 20 159.0 300 6.26 20 213.0 300 8.39 20 219.0 300 8.62 20 273.0 300 10.75

Dimensions B C mm / in mm / in 139.0 46.0 5.47 1.81 168.0 46.0 6.61 1.81 200.0 50.0 7.87 1.97 267.0 50.0 10.50 1.97 279.0 50.0 11.00 1.97 335.0 60.0 13.19 2.36

Allowable Pipe Bolt End Separation Deflection Size mm / in ( ° ) in 3.2 ⅜" x 2⅛" 2° 43' 0.13 3.2 ½" x 3" 1° 53' 0.13 3.2 ½" x 3" 1° 29' 0.13 3.2 ⅝" x 3½" 1° 2' 0.13 3.2 ⅝" x 3½" 1° 1' 0.13 3.2 ¾" x 4¾" 0° 47' 0.13

Weight Kgs / Lbs 1.1 2.4 1.5 3.9 2.2 4.8 3.5 5.0 3.8 5.3 5.9 7.4

MODEL

SD-28 Shouldered TOGGLE COUPLING The Shurt Model SD-28 coupling is

use of a split pin prevents accidental opening

designed to connect shouldered-end pipe

of the couplings. The housing segments

with Type A rings for services where frequent

are made of ductile iron to ASTM A536 Gr.

assembly and disassembly is desired or

65-45-12 and or A395 Gr. 65-45-15 and are

required. The housing segments are hinged

normally supplied in hot-dip galvanized. The

with a lever handle for easy installation. The

standard rubber gasket is Grade T Nitrile.


Nom. Rating

Class 150

B



300 psi @100°F 20 Bar @38°C


Split pin



Pipe OD mm / in 60.3 2.375 88.9 3.500 114.3 4.500 165.1 6.500 168.3 6.625 219.1 8.625

C

Max. Working Pressure A Bar / PSI mm / in 20 86.5 300 39.32 20 126 300 4.96 20 160 300 6.30 20 214 300 8.43 20 217 300 8.54 20 278 300 10.95


A

Dimensions B C mm / in mm / in 112.5 49 4.43 1.93 164 49 6.46 1.93 214 52 8.43 2.05 283 52 11.14 2.05 282 52 11.10 2.05 360 60 14.17 2.36

Allowable Pipe End Separation (E) Deflection mm / in ( ° ) 3.2 2º - 43' 0.125 3.2 1º - 53' 0.125 3.2 1º - 29' 0.125 3.2 1º - 2' 0.125 3.2 1º - 1' 0. 125 3.2 0º - 47' 0.125

www.shurt.com

Weight Kgs / Lbs 1.3 2.8 2.0 4.4 3.0 6.6 4.3 6.5 4.5 9.9 8.3 18.3


Plain-End Piping system for Steel Pipe

Catalog 2011

MODEL

79 WILDCAT™

coupling

The Shurt Model 79 Wildcat™ coupling

pipe ends (* For sizes larger than 350mm

is designed to mechanically plain-

(14”), jaws are made of 17-4PH stainless

end or beveled end carbon steel pipe.

steel.)

The Wildcat™ couplings can be used for

The Shurt Wildcat™ coupling is

a variety of applications including mining,

recommended for use on steel pipe

process piping, manifold piping and oilfield

with a hardness less than HB 150, not

services. The Wildcat™ couplings feature

recommended for plastic, HDPE, cast iron or

case-hardened jaws* within the housings

other brittle pipe.

and large diameter heat treated track bolts

Gaskets are available either in Grade E

that when tightened securely grip the pipe

EPDM for water services of -29°F to + 230°F

surface. As with grooved couplings, a

(-34°C to + 110°C) or Grade T Nitrile for oil

C-shaped rubber gasket effectively seals the

services -20°F to +180°F (-29°C to +82°C).

Hardened Steel Jaws Gasket

Housing Segment Bolt / Nut

Steel Pipe 2" – 16" (Hardness HB 150 max.)

Pressure-Temperature Rating Size in / mm

Nom. Rating

2 CWP 50 2½ – 3 CWP 65 - 80 4 CWP 100 5 – 6 CWP 125 - 150 8 – 12 CWP 200 - 300 14 CWP 350 16 CWP 400

Working Pressure (STD) 750 psi @100°F 52 Bar @38°C 600 psi @100°F 42 Bar @38°C 450 psi @100°F 32 Bar @38°C 300 psi @100°F 21 Bar @38°C 250 psi @100°F 17 Bar @38°C 200 psi @100°F 14 Bar @38°C 150 psi @100°F 10 Bar @38°C


Bolts and nuts must always be tightened to the required torque. EPDM: 230°F / 110°C Nitrile: 180°F / 82°C

A

*Working pressure is for plain-end standard wall steel pipe with hardness less than HB150. *Proof test pressure: 1.5 times the working pressure, non-shock cold water. *Burst pressure is engineered minimum 2 times the working pressure.

Nominal Size mm / in 50 2 65 2½ 80 3 100 4 125 5 150 6 200 8 250 10 300 12 350 14 400 16


Pipe OD mm / in 60.3 2.375 73.0 2.875 88.9 3.500 114.3 4.500 141.3 5.563 168.3 6.625 219.1 8.625 273.0 10.750 323.9 12.750 355.6 14.000 406.4 16.000

C

B

Max. Working Pressure Bar / PSI 52 750 42 600 42 600 32 450 21 300 21 300 17 250 17 250 17 250 14 200 10 150

Max. End Load kN / Lbs 14.84 3320 17.57 3890 26.06 5770 32.82 7150 32.91 7290 46.69 10340 64.06 14600 99.46 22680 140.00 31900 138.97 30770 129.65 30140


2"~ 16"

Required Bolt Bolt Torque Size A N-m / Lbs-Ft. No. in mm / in 200 95 2 ⅝ x 3½ 150 3.75 200 108 2 ⅝ x 3½ 150 4.25 270 127 2 ¾ x 4¾ 200 5.00 270 154 2 ¾ x 4¾ 200 6.14 340 187 2 ⅞ x 6½ 250 7.36 340 216 2 ⅞ x 6½ 250 8.50 270 276 4 ¾ x 4¾ 200 10.88 400 320 4 ⅞ x 6½ 300 12.60 470 371 4 1 x 6½ 350 14.60 470 424 4 1 x 6½ 350 16.70 470 475 4 1 x 6½ 350 18.70

Dimensions B mm / in 171 6.75 181 7.13 216 8.50 223 8.78 262 10.31 292 11.50 361 14.21 406 16.00 457 18.00 508 20.00 559 22.00

www.shurt.com

C mm / in 98 3.86 98 3.86 98 3.86 102 4.00 111 4.38 111 4.38 127 5.00 127 5.00 135 5.30 156 6.15 156 6.15

Weight Kgs / Lbs 3.2 7.0 3.3 7.3 5.0 11.0 6.5 14.3 11.0 24.2 13.0 28.6 19.0 41.8 24.0 52.8 28.7 63.1 42.5 93.5 43.5 95.7

Section 7 HDPE Series HDPE Series........................................................................................112

H305 HDP Coupling.........................................................................113 H307 HDP Transition Coupling.........................................................114 H312 HDP Flange Adapter...............................................................115

Catalog 2011

Catalog 2011

HDPE Series Shurt offers a series HDPE couplings and adapters for ing HDPE pipe. The use of HDPE (high density polyethelyene) pipe continues to grow in popularity as it's benefits over traditional materials are realized in a variety of service applications. The features of HDPE pipe include a long service life, flexibility, light in weight, increased resistance to corrosion and chemicals, fatigue and superior flow characteristics. HDPE is now commonly used in service applications including municipal water and waste water, water distribution and transport, mining, slurry and many other general and industrial applications.

Pressure Ratings (psi) - IPS Size

Pipe Dimension PE4710 Ratio (DR) PE100 DR 7.3 317 DR 9 250 DR 11 200 DR 13.5 160 DR 17 125 DR 21 100 DR 26 80 DR 32.5 63

PE3608 PE3408 265 200 160 130 100 80 65 50

Design stress: PE4710 1000 psi, PE3608 & 3408 800 psi

D

Shurt HDPE couplings provide a fast

As the ductile iron coupling is much

and easy way to mechanically HDPE

stronger than HDPE pipe itself, pressure

pipe. A series of sharply machined teeth

ratings of HDPE couplings are determined

securely grip the pipe as the bolts are

by the pressure rating of HDPE pipe

tightened, resulting in a leak-free t. The

used. Pressure ratings of HDPE pipe

Shurt ing method eliminates the

vary depending on DR or SDR (standard

need for costly heat fusion equipment. The

dimension ratio) and design stress of the

highly restrained t allows long lengths of

material.

pipe to be pulled from one area to another. With the removal of a few bolts one can

DR (Pipe Dimension Ratio) DR = t Where: D = pipe outside diameter, in t = pipe minimum wall thickness, in

Pressure Ratings (Bar) - ISO Size

Pipe Dimension Ratio (SDR) PE100 SDR 9 20 SDR 11 16 SDR 17 10 SDR 26 6.3

PE80 16 10 6.3 4

Design Stress: PE100 8.0 MPa, PE80 5.0 MPa

easily access the system for cleaning,

SDR (Standard Dimension Ratio) SDR = Where: D = pipe outside diameter, mm t = pipe minimum wall thickness, mm

maintenance, changes and or system expansion.

D t

Shurt HDPE couplings are designed to IPS HDPE pipe, DR32.5 to 7.3, conforming to ASTM D2513, D3350 and or ANSI/AWWA C901 and ISO HDPE pipe, SDR 9 to 26, conforming to ISO 4427-1/2.

How to install

Marking Use a marker and

Gasket Mounting Place a

Housing Mounting Lubricate

the gasket and or housings and

the nuts alternatively until the

on each pipe end, 1" from each

center the gasket in between

place the housings over gasket

housing bolt pads meet metal

end.

the marks. The pipe ends must

and insert bolts. Install nuts

to metal.

always be butted against each

finger tight.

measuring tape to place marks

gasket over the pipe ends and

Nut Tightening Ti g h t e n

other.

Refer to the Shurt installation instruction manual for complete instructions. Shurt HDPE couplings are not intended for use on PVC, PP or other materials.



www.shurt.com

Catalog 2011

MODEL

H305 HDP COUPLING The Shurt Model H305 HDP couplings feature four bolt housings and a series of sharply machined teeth which securely grip

B

C

the pipe as the bolts and nuts are tightened. The result is a leak-tight t that is as strong as or stronger than the pipe itself. The

A

H305 also features a contoured housing with integral ramps along the outside diameter to help the coupling slide over most obstacles during the relocation of pipe runs.

H305 - IPS Size

Nominal Size mm / in 50 2 80 3 100 4 150 6 200 8 250 10 300 12 350 14 400 16 450 18 500 20

Pipe O. D. A mm / in mm / in 60.3 86 2.375 3.39 88.9 117 3.500 4.61 114.3 146 4.500 5.75 168.3 200 6.625 7.87 219.1 264 8.625 10.39 273.0 318 10.750 12.52 323.9 365 12.750 14.37 355.6 413 14.000 16.26 406.4 467 16.000 18.39 457.2 515 18.000 20.28 508.0 568 20.000 22.36

Dimensions Coupling Bolts B C Size Weight mm / in mm / in No. in Kgs / Lbs 133 117 2.6 4 ½ x 2⅜ 5.24 4.61 5.7 165 102 3.6 4 ½ x 2¾ 6.50 4.02 7.9 203 146 5.2 4 ½x3 7.99 5.75 11.4 273 149 8.2 4 ⅝ x 3½ 10.75 5.87 18.0 333 152 12.9 4 ⅝ x 3½ 13.11 5.98 28.4 397 165 19.8 4 ¾ x 4¾ 15.63 6.50 43.6 448 200 25.5 4 ¾ x 4¾ 17.64 7.87 56.1 492 257 41.2 4 1 x 4½ 19.37 10.12 90.6 543 257 44.2 4 1 x 4½ 21.38 10.12 97.2 595 260 50.5 4 1 x 4½ 23.43 10.24 111.1 651 260 61.8 4 1 x 4½ 25.63 10.24 136.0

* Shurt recommends the use of a silicone based lubricant for the HDP series.

H305 - ISO Size

Min. mm 50 63 75 90 110 160 180 200 225 250 280 315 355 400 450 710 800 900

Pipe O. D. Max. A mm mm 50.5 72 63.6 85 75.7 97 90.9 113 111.0 139 161.5 190 181.7 211 201.8 236 226.4 261 252.3 289 281.7 319 317.9 354 357.2 412 402.4 462 452.7 515 716.4 800 807.2 889 908.1 991

Dimensions Coupling Bolts B C Size mm mm No. mm 115 105 4 M10 x 55 128 105 4 M10 x 55 140 105 4 M10 x 55 169 105 4 M12 x 75 181 112 4 M12 x 75 232 118 4 M12 x 75 253 118 4 M12 x 75 305 127 4 M16 x 90 330 127 4 M16 x 90 351 134 4 M16 x 120 406 134 4 M16 x 90 438 134 4 M20 x 120 489 256 4 M20 x 120 540 256 4 M24 x 120 595 256 4 M24 x 120 902 276 4 M30 x 100 991 276 4 M30 x 100 1092 276 4 M30 x 100

Approx. Weight Kgs 1.5 1.9 2.4 3.3 4.0 5.6 7.5 9.4 11.3 12.7 18.4 16.7 36.7 45.5 57.7 166.0 187.0 210.0



www.shurt.com


Catalog 2011

MODEL

H307 HDP TRANSITION COUPLING The Shurt Model H307 transition coupling provides for a fast, easy and direct

B

transition from HDP pipe and or fittings to

C

grooved end steel pipe (IPS). A

H307 - IPS Size

Nominal Size mm / in 50 2 80 3 100 4 150 6 200 8 250 10 300 12

Pipe O. D. A mm / in mm / in 60.3 86 2.375 3.39 88.9 114 3.500 4.49 114.3 146 4.500 5.75 168.3 203 6.625 8.00 219.1 267 8.625 10.51 273.0 321 10.750 12.64 323.9 375 12.750 14.76

Dimensions Coupling Bolts B C Size Weight mm / in mm / in No. in Kgs / Lbs 152 79 2.0 4 ½ x 2⅜ 5.99 3.11 4.4 181 79 2.7 4 ½x3 7.13 3.11 5.9 216 95 3.8 4 ½x3 8.50 3.74 8.4 286 95 5.7 4 ⅝ x 3½ 11.26 3.74 12.5 346 108 9.7 4 ⅝ x 3½ 13.63 4.25 21.3 432 127 16.0 4 ¾ x 4¾ 17.00 5.00 35.2 495 127 19.6 4 ¾ x 4¾ 19.49 5.00 43.1

*Shurt recommends the use of a silicone based lubricant for use with the HDP series.

B

C

A

H307 - ISO Size

HDPE mm 63.0 75.0 90.0 110.0 160.0 160.0 200.0 250.0 315.0

Pipe O. D. STEEL A mm mm 60.3 86 73.0 97 88.9 114 114.3 144 165.1 194 168.3 198 219.1 256 273.0 321 323.9 375

Dimensions Coupling Bolts B C Size mm mm No. mm 146 73 4 M10 x 55 146 73 4 M10 x 55 178 73 4 M12 x 75 203 76 4 M12 x 75 254 76 4 M12 x 75 257 76 4 M12 x 75 321 84 4 M16 x 90 432 127 4 M16 x 120 495 127 4 M20 x 120




www.shurt.com

Approx. Weight Kgs 1.5 1.9 2.3 2.8 3.9 3.9 6.4 11.9 12.7

Catalog 2011

MODEL

H312 HDP FLANGE ADAPTER

B

C

The Shurt Model H312 HDP flange adapter provides for the direct transition from

A

HDP pipe and or fittings to ANSI Class 125 or 150 flanged components.

H312 - IPS Size / ANSI Class 125/150


Pipe O. D. A mm / in mm / in 88.9 197 3.500 7.75 114.3 229 4.500 9.00 168.3 279 6.625 11.00 219.1 343 8.625 13.50 273.0 406 10.750 16.00 323.9 483 12.750 19.02

Dimensions Flang Bolt B C Size Weight mm / in mm / in No. in Kgs / Lbs 225 79 4.8 4 ⅝ 8.86 3.10 10.6 260 79 6.8 8 ⅝ 10.25 3.10 15.0 311 95 9.8 8 ¾ 12.25 3.75 21.5 375 87 13.1 8 ¾ 14.75 3.42 28.8 533 108 19.5 12 ⅞ 21.0 4.25 42.9 610 108 23.4 12 ⅞ 24.0 4.25 51.5

* Shurt recommends the use of a silicone based lubricant for use with the HDP series. * Flange bolts and nuts are to be supplied by installer.

B

C

A

H312 - ISO Size / PN 10/16

HDPE mm 75 90 110 160 200 250 315

Pipe O. D. STEEL A mm mm 76.1 185 88.9 200 114.3 220 168.3 285 219.1 340 273.0 405 323.9 460

Dimensions Flange Bolt B C Size mm mm No. mm 213 79 4 M16 228 79 8 M16 251 79 8 M16 317 95 8 M20 372 87 12 (PN 16) M20 532 108 12 M24 587 108 12 M24

Approx. Weight Kgs 4.3 4.8 6.8 9.8 13.1 19.5 28.5

* Shurt recommends the use of a silicone based lubricant for use with the HDP series. * Flange bolts and nuts are to be supplied by installer.


www.shurt.com


Catalog 2011



www.shurt.com

Section 8 Copper Series Grooved Couplings & Fittings for Copper Tubing. .............118 Pressure Ratings of Copper Tubing..........................................118 Roll Groove Standard for Copper Tubing...............................118 Grooved Couplings & Flanges for Copper Tubing C305 Rigid Coupling..........................................................................119 C306 Reducing Coupling / 96 Continuity Clip................................. 120 C307 Transition Coupling................................................................. 121 C341 Flange Adapter........................................................................ 122 Grooved Fittings for Copper Tubing C10-W / C11-W / C20-W Elbows, Tee........................................ 122 C10 / C11 / C20 / C60 Elbows, Tee, Cap..................................... 122 C21 / C50 / C26 Reducing Tees, Concentric Reducer.................. 123 C52 / C55 Concentric Reducer, Transition Adapter......................... 124 C55T / DE30-GG Transition Adapters, Dielectric Transition Fitting.... 126

Mechanical Tees & Flow Control Components

C723 Mechanical Tee....................................................................... 126 C726 Y-Strainer................................................................................ 127 SJ-C300 Butterfly Valve.................................................................. 128

Catalog 2011

Catalog 2011

Grooved Couplings, Fittings & Components for Copper Tubing The Shurt copper series is the most complete line of grooved components available for installation on copper tubing (CTS) in sizes 2” - 6” (50 - 150 mm). Shurt grooved mechanical components provide a fast, easy, economical and durable ing method of copper tubing without the use of heat or solder. Grooved-end fittings are produced from wrought copper and or bronze castings. Wrought copper conforms to ASTM B75 UNC C12200 (99.9% copper). Bronze castings are produced from lead-free alloys C90500 and or C89836 Bismuth bronze per ASTM B584. Materials are in compliance with ANSI/NSF 61 for potable water service applications.

Standard Roll Groove for U.S. Standard Copper Tubing t

A

O.D.

B C

d



Pipe O. D. mm / in 54.0 2.125 66.7 2.625 79.4 3.125 104.8 4.125 130.2 5.125 155.6 6.125

Copper Tubing - Dimensions & Pressure Ratings (ASTM B88 & B306) Nominal D Size Type Pipe OD mm / in mm / in K 50 L 54 2 M 2.125 DWV K 65 L 66.7 2½ M 2.625 DWV K 80 L 79.4 3 M 3.125 DWV K 100 L 104.8 4 M 4.125 DWV K 125 L 130.2 5 M 5.125 DWV K 150 L 155.6 6 M 6.125 DWV

t Thickness

mm 2.11 1.78 1.47 1.07 2.41 2.03 1.65 N/A 2.77 2.29 1.83 1.14 3.40 2.79 2.41 1.47 4.06 3.12 2.77 1.83 4.88 3.56 3.10 2.11

in 0.083 0.070 0.058 0.042 0.095 0.080 0.065 N/A 0.109 0.090 0.072 0.045 0.134 0.110 0.095 0.058 0.160 0.123 0.109 0.072 0.192 0.140 0.122 0.083

P Max. Pressure Bar psi 33 484 28 406 23 335 17 241 31 447 26 375 21 303 N/A N/A 30 431 24 354 19 282 12 175 28 400 23 327 19 282 12 171 26 384 20 294 18 260 12 171 27 386 19 279 17 243 11 164

Notes: 1. Design stress: 6000 psi (41.4 MPa) 2. Pressures are based on water at 23°C (73.4°F).

Roll Set

As copper tubing is thinner than carbon steel pipe, always use a roll set specifically designed for use on copper tubing. Pipe OD Maximum allowable tolerances from square cut ends is 0.03" for 2" thru 3"; 0.045" for 4" thru 6"; and 0.060" for sizes 8". Gasket Seating Surface The gasket seating surface shall be free from deep scores, marks, or ridges that could prevent a positive seal. Groove Width Groove width is to be measured between vertical flanks of the groove side walls. Groove Diameter The 'C' diameters are average values. The groove must be of uniform depth around the entire pipe circumference.

Gasket Seat A ±0.79 mm ±0.03 in 15.5 0.610 15.5 0.610 15.5 0.610 15.5 0.610 15.5 0.610 15.5 0.610


Groove Width B ±0.79 mm ±0.03 in 7.6 0.300 7.6 0.300 7.6 0.300 7.6 0.300 7.6 0.300 7.6 0.300

Groove Dia. C +0/-0.51 mm +0/-0.02 in 51.5 2.029 64.1 2.525 76.8 3.025 102.1 4.019 127.0 4.999 152.3 5.999

Groove Depth The 'd' is for reference use only. The groove dimension shall be determined by the groove diameter 'C'. Minimum Wall Thickness The DWV pipe (ASTM B-306) is minimum wall thickness that may be roll grooved. Flare Diameter The pipe end that may flare when the groove is rolled shall be within this limit when measured at the extreme end of the pipe.

Groove Depth Min. Allow d (ref) Wall Thick t mm / in mm / in 1.2 1.6 0.048 0.064 1.3 1.7 0.050 0.065 1.3 DWV 0.050 1.4 DWV 0.053 1.4 DWV 0.053 1.6 DWV 0.063

www.shurt.com

Max. Allowed Flare Dia. mm / in 56.4 2.220 69.1 2.720 81.8 3.220 107.2 4.220 132.6 5.220 158.0 6.220

Catalog 2011

MODEL

C305 RIGID COUPLING FOR COPPER TUBING (CTS) The Model C305 features angle bolt pad

housings and EPDM GapSeal® gaskets and

design for a rigid t and easy swing-

are rated up to 300 psi (20 bar), depending

over installation. The C305 couplings are

on the type and size of copper tubing used.

comprised of epoxy coated ductile iron Pressure-Temperature Rating Nom. Rating Class 150

Working Pressure


300 psi @100°F 20 Bar @38°C

EPDM: 230°F / 110°C

*Working pressure is for connection with roll-grooved Type K copper tubing. *Proof test pressure: 1.5 times the working pressure. *Burst pressure: 3 times the listed working pressure, min.

C

B

A

TYPE K, L, M (ASTM B-88) & TYPE DWV (ASTM B306)


BS EN 1057

Nominal Size mm 50 65 80 100 125 150

Pipe OD mm / in 54.0 2.125 66.7 2.625 79.4 3.125 104.8 4.125 130.2 5.125 155.6 6.125

Pipe O. D. mm 54.0 66.7 76.1 108.0 133.0 159.0

Pipe End Separation A mm / in mm / in 1.5 81 0.06 3.17 1.5 93 0.06 3.66 1.5 107 0.06 4.21 1.5 132 0.06 5.20 1.5 159 0.06 6.26 1.5 184 0.06 7.24

Dimensions Bolt / Nut B C Size mm / in mm / in in 118 48 ⅜ x 2⅛ 4.63 1.89 134 48 ⅜ x 2⅛ 5.28 1.89 154 48 ½x3 6.06 1.89 185 48 ½x3 7.28 1.89 220 48 ⅝ x 3½ 8.66 1.89 248 48 ⅝ x 3½ 9.76 1.89

Pipe End Separation A mm mm 1.5 81 1.5 93 1.5 104 3.2 138 3.2 165 3.2 190

Dimensions B C mm mm 118 48 134 48 141 48 192 48 231 48 253 48

Bolt / Nut Size mm M10 x 55 M10 x 55 M10 x 55 M12 x 75 M16 x 90 M16 x 90

Weight kgs 0.8 0.9 1.3 1.6 2.2 2.5

Dimensions B C mm mm 115 48 134 48 154 48 183 48 220 48 249 48

Bolt / Nut Size mm M10 x 55 M10 x 55 M12 x 75 M12 x 75 M16 x 90 M16 x 90

Weight kgs 0.8 0.9 1.3 1.6 2.1 2.5

AS1432 TYPE "A" , "B" AND "D"

Nominal Size mm 50 65 80 100 125 150

Pipe O. D. mm 50.80 63.50 76.20 101.60 127.00 152.40

Pipe End Separation A mm mm 1.5 77 1.5 90 1.5 103 1.5 129 1.5 156 1.5 181


www.shurt.com

Weight Kgs / Lbs 0.8 1.8 0.9 2.0 1.3 2.8 1.6 3.5 2.2 4.6 2.5 5.5


Catalog 2011

MODEL

C306 REDUCING COUPLING FOR COPPER TUBING (CTS) The Model C306 Reducing Coupling

local cell and stray current problems. The

allows direct reduction on a piping run and

specially designed rubber gasket prevents

eliminates the need for a concentric reducer

the smaller pipe from telescoping into the

and couplings. The epoxy coated ductile iron

larger pipe during vertical installation.

coupling housings help eliminate galvanic Pressure-Temperature Rating Nom. Rating Class 150

Working Pressure


300 psi @100°F 20 Bar @38°C

EPDM: 230°F / 110°C


Nominal Pipe Size OD mm / in mm / in 65 x 50 66.7 x 54.0 2½ x 2 2.625 x 2.215 80 x 50 79.4 x 54.0 3 x 2 3.125 x 2.125 80 x 65 79.4 x 66.7 3 x 2½ 3.125 x 2.625 100 x 65 104.8 x 66.7 4 x 2½ 4.125 x 2.625 100 x 80 104.8 x 79.4 4 x 3 4.125 x 3.125 125 x 100 130.2 x 104.8 5 x 4 5.125 x 4.125 150 x 100 155.6 x 104.8 6 x 4 6.125 x 4.125

Max. Working Pressure Bar / PSI 20 300 20 300 20 300 20 300 20 300 20 300 20 300

Max. End Load kN / Lbs 6.98 1622 9.89 2300 9.89 2300 17.23 4007 17.23 4007 26.60 6186 37.99 8835

C

B

A

Pipe Deflection Dimensions End Deg. Per Per Bolt Separation Coupling Pipe A B C Size mm / in ( ° ) mm / m in / ft mm / in mm / in mm / in in 1.6 24.0 94 141 45 1° – 22' ½x3 0.06 0.29 3.70 5.55 1.77 1.6 20.0 107 152 45 1° – 09' ½x3 0.06 0.24 4.21 5.98 1.77 1.6 20.0 107 152 45 1° – 09' ½x3 0.06 0.24 4.21 5.98 1.77 1.6 15.0 132 183 45 0° – 53' ½x3 0.06 0.18 5.20 7.20 1.77 1.6 15.0 132 183 45 0° – 53' ½x3 0.06 0.18 5.20 7.20 1.77 1.6 12.0 160 224 45 0° – 42' ⅝ x 3½ 0.06 0.15 6.30 8.82 1.77 1.6 10.3 185 251 45 0° – 36' ⅝ x 3½ 0.06 0.13 7.28 9.88 1.77

MODEL

96 CONTINUITY CLIP Couplings with rubber gaskets are likely to function as an insulator. Where electrical continuity is required, the Shurt continuity clip will restore electrical continuity to the system. The electrical continuity clip satisfies IEE Wiring Regulations. Material: Copper or Brass plate. Note: The pipe surface where continuity clips come in must be conductive. If the surface is painted, the paint should be removed to expose bare metal.



Model 96-1 96-2 96-3

Coupling Size 1" - 3" 4" - 6" 8" - 12"

Box Q’ty/pcs 125 125 100

www.shurt.com

Weight Kgs / Lbs 1.3 2.9 1.5 3.3 1.4 3.0 1.9 4.2 1.8 4.0 2.5 5.5 3.3 7.3

Catalog 2011

MODEL

C307 TRANSITION COUPLING (IPS X CTS) The Model C307 Transition Coupling provides for a direct connection and transition between grooved end IPS steel pipe, fittings or valves and grooved end CTS copper tubing. The

IPS Steel Pipe

rubber gasket isolates the fluid from coupling housings and the epoxy coated housings help. eliminate galvanic local cell and stray current

CTS Copper Tubing C307

problems. The C307 is rated to 300 psi (20 bar). Pressure-Temperature Rating Nom. Rating Class 150

B

Working Pressure


300 psi @100°F 20 Bar @38°C

EPDM: 230°F / 110°C


Pipe OD IPS x CTS mm / in 60.3 x 54.0 2.375 x 2.125 73.0 x 66.7 2.875 x 2.625 88.9 x 79.4 3.500 x 3.125 114.3 x 104.8 4.500 x 4.125

IPS B'fly Valve

CTS Copper Tubing

A


C

C307

Pipe End Separation Deflection A mm / in ( ° ) mm / in 0 - 1.6 84 1° – 31' 0 - 0.06 3.31 0 - 1.6 99 1° – 15' 0 - 0.06 3.90 0 - 1.6 116 1° – 02' 0 - 0.06 4.57 0 - 1.6 145 1° – 36' 0 - 0.06 5.71

CTS Copper Tubing C307

Dimensions Bolt / Nut B C Size Weight mm / in mm / in in Kgs / Lbs 129 48 0.9 ½ x 2⅛ 5.08 1.89 2.0 142 48 1.0 ⅜ x 2⅛ 5.59 1.89 2.2 169 48 1.4 ½x3 6.65 1.89 3.0 197 52 1.9 ½x3 7.76 2.05 4.2

MODEL

C341 Flange adapter FOR COPPER TUBING (CTS) The Shurt Model C341 Flange Adapter

heat or solder. The pressure responsive

allows for the direct connection of grooved-

gasket seals on the outside diameter of

end copper tubing with ANSI class 125/150

the copper tubing and isolates the flange

(steel) or ASME B16.24 (copper) class 150

segments from the internal fluid.

flanged components without the need for

A


Working Pressure


300 psi @100°F 20 Bar @38°C

EPDM: 230°F / 110°C

D E

C

B

*Working pressure is for connection with roll-grooved Type K copper tubing. *Hydrostatic Shell Test: 1.5 times the working pressure, nonshock cold water.


Pipe OD A mm / in mm / in 54.0 152 2.125 6.00 66.7 178 2.625 7.00 79.4 190 3.125 7.50 104.8 229 4.125 9.00 130.2 254 5.125 10.00 155.6 279 6.125 11.00

Dimensions B C mm / in mm / in 121 19 4.75 0.75 140 22 5.50 0.87 152 24 6.00 0.94 191 24 7.50 0.94 216 24 8.50 0.94 241 25 9.50 1.00

Sealing Surface Bolts D E Size mm / in mm / in No. in 54 81 4 ⅝x3 2.13 3.20 67 99 4 ⅝x3 2.63 3.91 80 115 4 ⅝x3 3.13 4.53 105 140 4 ⅝x3 4.13 5.53 130 170 8 ¾ x 3½ 5.13 6.71 156 198 8 ¾ x 3½ 6.13 7.79

Weight Kgs / Lbs 2.1 4.6 3.0 6.6 3.5 7.7 4.3 9.5 5.8 12.8 6.2 13.6

* Please note that 2”, 2-1/2”, and 3” Model C341 Flanges cannot be used for making direct connections to Model SJ-C300 Butterfly Valves due to bolt pad interference with the valve.


www.shurt.com


Catalog 2011

Grooved Fittings for Copper Tubing Shurt Grooved-end fittings are produced from wrought copper and or bronze castings. Wrought copper conforms to ASTM B75 UNC C12200 (99.9% copper). Bronze castings are produced from lead-free alloys

C90500 and or C89836 Bismuth bronze per

components and ASTM B-88 roll grooved

ASTM B584. Materials are in compliance

copper tubing type K, L, M and ASTM B-306

with ANSI/NSF 61 for potable water service

DWV.

applications. Shurt fittings are designed for use with Shurt CTS couplings,

MODELs


Pipe OD mm / in 54.0 2.125 66.7 2.625 79.4 3.125 104.8 4.125

C10-W 90° Elbow C-E Weight mm / in Kgs / Lbs 74 0.34 2.91 0.75 84 0.52 3.31 1.15 97 0.85 3.81 1.88 121 1.85 4.75 4.07

C-E

E

E

C-

C-

C-E

E

C-E

C-

C10-W 90° ELBOW (Wrought) C11-W 45° ELBOW (Wrought) C20-W Tee (Wrought) C-E

C-E

C11-W 45° Elbow C-E Weight mm / in Kgs / Lbs 56 0.28 2.19 0.61 59 0.40 2.31 0.89 66 0.63 2.59 1.38 81 1.36 3.19 2.99

C-E mm / in 68 2.69 81 3.20 89 3.52 108 4.25

C-E E-E

C20-W Tee

E-E

Weight Kgs / Lbs 0.66 1.45 1.07 2.37 1.53 3.38 2.62 5.77



Pipe OD mm / in 54.0 2.125 66.7 2.625 79.4 3.125 104.8 4.125 130.2 5.125 155.6 6.125

C10 90° Elbow C-E Weight mm / in Kgs / Lbs 74 0.7 2.91 1.5 84 0.9 3.31 2.0 97 1.2 3.81 2.6 121 2.5 4.75 5.5 151 5.2 5.94 11.5 176 7.5 6.94 16.5


C-E mm / in 62 2.44 81 3.20 89 3.50 108 4.25 151 5.94 176 6.94

C-E

E-E E-E E-E

E-E

C-E

C-E C11 45° Elbow C-E Weight mm / in Kgs / Lbs 56 0.8 2.19 1.7 59 1.0 2.31 2.1 66 1.4 2.59 3.2 81 2.5 3.19 5.5 83 3.6 3.25 7.9 92 4.6 3.63 10.2

C-E C-E C-E

C-E C-E

C-E

C -E

C-E C-E C-E

C -E

C10 90º ELBOW (Cast) C11 45º ELBOW (Cast) C20 TEE (Cast) C60 CAP (Cast)

C C-E -E

MODELs

C20 Tee

Weight Kgs / Lbs 0.8 1.8 1.3 2.9 1.7 3.7 3.3 7.3 7.8 17.2 11.9 26.2

www.shurt.com

E-E in 24 0.96 24 0.96 24 0.96 24 0.96 24 0.96 24 0.96

C60 Cap

Weight Kgs / Lbs 0.3 0.6 0.4 0.9 0.6 1.2 1.0 2.1 1.6 3.5 2.0 4.4

E-E

Catalog 2011

MODELs

C21 REDUCING TEE (Cast) C50 CONCENTRIC

REDUCER (Cast)

C-E

C-E E-E

Nominal Size mm / in 65 x 50 2½ x 2 80 x 50 3 x 2 80 x 65 3 x 2½ 100 x 50 4 x 2 100 x 65 4 x 2½ 100 x 80 4 x 3 125 x 80 5 x 3 125 x 100 5 x 4 150 x 65 6 x 2½ 150 x 80 6 x 3 150 x 100 6 x 4 150 x 125 6 x 5

Pipe O. D. mm / in 66.7 x 54.0 2.625 x 2.125 79.4 x 54.0 3.125 x 2.125 79.4 x 66.7 3.125 x 2.625 104.8 x 54.0 4.125 x 2.125 104.8 x 66.7 4.125 x 2.625 104.8 x 79.4 4.125 x 3.125 130.2 x 79.4 5.125 x 3.125 130.2 x 104.8 5.125 x 4.125 155.6 x 66.7 6.125 x 2.625 155.6 x 79.4 6.125 x 3.125 155.6 x 104.8 6.125 x 4.125 155.6 x 130.2 6.125 x 5.125

Nominal Size C-E mm / in mm / in 50 x 50 x 20 56 2 x 2 x ¾ 2.20 50 x 50 x 25 59 2 x 2 x 1 2.33 50 x 50 x 32 63 2 x 2 x 1¼ 2.48 50 x 50 x 40 66 2 x 2 x 1½ 2.60 65 x 65 x 20 58 2.½ x 2½ x ¾ 2.28 65 x 65 x 25 61 2½ x 2½ x 1 2.40 65 x 65 x 32 64 2½ x 2½ x 1¼ 2.52 65 x 65 x 40 69 2½ x 2½ x 1.5 2.70 65 x 65 x 50 75 2½ x 2½ x 2 2.95 80 x 80 x 20 62 3 x 3 x ¾ 2.44 80 x 80 x 25 65 3 x 3 x 1 2.54 80 x 80 x 32 67 3 x 3 x 1¼ 2.63 80 x 80 x 40 72 3 x 3 x 1½ 2.85 80 x 80 x 50 79 3 x 3 x 2 3.11 100 x 100 x 20 76 4 x 4 x ¾ 3.00 100 x 100 x 25 79 4 x 4 x 1 3.10 100 x 100 x 32 83 4 x 4 x 1¼ 3.25 100 x 100 x 40 85 4 x 4 x 1½ 3.35 100 x 100 x 50 92 4 x 4 x 2 3.62

C21 Reducing Tee C-E Weight mm / in Kgs / Lbs 81 1.6 3.20 3.6 89 2.2 3.50 4.8 89 2.2 3.50 4.8 108 3.5 4.25 7.7 108 3.6 4.25 7.9 108 3.7 4.25 8.1 151 7.6 5.94 16.7 151 7.8 5.94 17.2 176 10.4 6.94 22.9 176 10.7 6.94 23.5 176 10.7 6.94 23.5 176 11.9 6.94 26.2

C50 Concentric Reducer E-E Weight mm / in Kgs / Lbs 64 0.6 2.50 1.2 64 0.7 2.50 1.5 64 0.7 2.50 1.5 76 1.2 3.00 2.5 76 1.2 3.00 2.6 76 1.1 3.00 2.5 89 2.0 3.50 4.4 89 2.0 3.50 4.4 102 2.7 4.00 6.0 102 2.7 4.00 5.9 102 2.7 4.00 5.8 102 2.7 4.00 5.9

MODELs

MODELs

C26 REDUCING TEE

(GR X GR X CUP) (Cast)

C-E C-B

Cup


C26 Red. Tee (Gr X Gr x Cup) C-B Cup Weight mm / in mm / in Kgs / Lbs 51 19 0.7 2.00 0.75 1.6 55 23 0.7 2.16 0.91 1.6 56 25 0.8 2.22 0.97 1.7 59 28 0.9 2.34 1.09 2.0 57 34 0.9 2.25 1.34 1.9 61 23 1.0 2.41 0.91 2.2 63 25 1.1 2.47 0.97 2.3 66 28 1.2 2.59 1.09 2.6 72 34 1.4 2.84 1.34 3.0 64 19 1.3 2.50 0.75 2.9 66 23 1.3 2.60 0.91 2.9 69 25 1.4 2.72 0.97 3.1 72 28 1.5 2.84 1.09 3.3 78 34 1.7 3.09 1.34 3.7 76 19 2.2 3.00 0.75 4.8 80 23 2.3 3.16 0.91 5.1 82 25 2.5 3.22 0.97 5.5 85 28 2.5 3.34 1.09 5.6 91 34 2.7 3.59 1.34 5.9

www.shurt.com


Catalog 2011

MODELs

C52 CONCENTRIC REDUCER (GR X GR X CUP) (Cast)

Nominal Size E-E mm / in mm / in 50 x 50 x 25 69 2 x 2 x 1 2.70 50 x 50 x 32 76 2 x 2 x 1¼ 3.00 50 x 50 x 40 75 2 x 2 x 1½ 2.94 65 x 65 x 25 83 2½ x 2½ x 1 3.25 65 x 65 x 32 89 2½ x 2½ x 1¼ 3.52 65 x 65 x 40 88 2½ x 2½ x 1.5 3.45 65 x 65 x 50 84 2½ x 2½ x 2 3.30 80 x 80 x 40 93 3 x 3 x 1½ 3.68 80 x 80 x 50 104 3 x 3 x 2 4.10 100 x 100 x 50 121 4 x 4 x 2 4.75

C52 Conc. Reducer (Gr X Gr X Cup) Cup Weight mm / in Kgs / Lbs 23 0.3 0.91 0.7 25 0.4 0.97 0.8 28 0.4 1.09 0.8 23 0.5 0.91 1.2 25 0.5 0.97 1.2 28 0.5 1.09 1.2 34 0.5 1.34 1.2 28 0.8 1.09 1.7 34 0.9 1.34 1.9 34 1.4 1.34 3.2

E-E

Cup

MODEL

C55 TRANSITION ADAPTER (IPS X CTS ) The Model C55 Transition Adapter provides a direct transition between male threadedend steel pipe (IPS) and grooved-end copper tubing. The C55 is UL classified to ANSI/NSF 61 for use in potable water systems.

Nominal Pipe Size IPS (NPT) x CTS (GRV) mm / in 40 x 50 1½ x 2 50 x 50 2 x 2 65 x 65 2½ x 2½ 80 x 80 3 x 3


Actual Pipe O.D. Steel Pipe (IPS) O.D. Copper Tubing (CTS) D mm / in mm / in 48.3 54.0 1.900 2.125 60.3 54.0 2.375 2.125 73.0 66.7 2.875 2.625 88.9 79.4 3.500 3.125


E-E mm / in 63 2.50 63 2.50 70 2.75 76 3.00

Weight Kgs / Lbs 0.6 1.3 0.7 1.4 1.1 2.4 1.5 3.3

NPT (IPS)

D(CTS)

E-E

www.shurt.com

Catalog 2011

MODEL

C55T TRANSITION ADAPTER (IPS/FT X CTS/GR ) WITH ¼" TAPS Allows for the installation of gauges or Pete's Plugs for measuring temperature and

¼" NPT

or pressure.

NPT

D(CTS)

(IPS) ¼" NPT E to E

Nominal Pipe Size IPS (NPT) x CTS (GRV) mm / in 40 x 50 1½ x 2 50 x 50 2 x 2 65 x 65 2½ x 2½ 80 x 80 3 x 3

Actual Pipe O.D. Steel Pipe (IPS) O.D. Copper Tubing (CTS) D mm / in mm / in 48.3 54.0 1.900 2.125 60.3 54.0 2.375 2.125 73.0 66.7 2.875 2.625 88.9 79.4 3.500 3.125

E-E mm / in 63 2.50 63 2.50 70 2.75 76 3.00

Weight Kgs / Lbs 0.5 1.1 0.6 1.3 0.9 2.0 1.5 3.3

Pete's Plug

(CTS)

(IPS) C55T

C305

MODEL

DE30-GG DIELECTRIC

TRANSITION FITTING (IPS X CTS)

The Model DE30-GG Dielectric Transition

end copper tubing (CTS). The internal PP

Fitting provides a direct transition between

lining effectively eliminates galvanic local

grooved-end steel pipe (IPS) and grooved-

cell and stray current problems.

Nominal Size mm / in 50 2 65 2½ 80 3 100 4 125 5 150 6 200 8

Actual Pipe O.D. IPS CTS mm / in mm / in 60.3 54.0 2.375 2.125 73.0 66.7 2.875 2.625 88.9 79.4 3.500 3.125 114.3 104.8 4.500 4.125 141.3 130.2 5.563 5.125 168.3 155.6 6.625 6.125 219.1 206.4 8.625 8.125


E-E mm / in 102 4.00 102 4.00 102 4.00 102 4.00 102 4.00 102 4.00 102 4.00

Weight Kgs / Lbs 0.6 1.3 0.9 1.9 1.3 2.9 1.5 3.3 2.4 5.2 3.1 6.9 4.3 9.4

Ductile Iron Body Virgin PP Lining

E-E

www.shurt.com


MODEL

C723 BRONZE MECHANICAL TEE FOR COPPER TUBING (CTS) The Shurt Model C723 provides a fast,

and nuts. The fitting is available with a

easy and reliable branch connection from

female threaded outlet, NPT or BSPT.

Catalog 2011

copper tubing (CTS). The fitting consists of a bronze upper housing, ductile iron lower housing, o-ring and carbon steel track bolts Pressure-Temperature Rating Nom. Rating

Working Pressure

Test Pressure @73°F / 23°C


Class 150

300 psi @100°F 20 Bar @38°C

450 psi 32 Bar

EPDM: 230°F / 110°C

*Working pressure is for connection with Type K copper tubing. • Proof test pressure: 1.5 times the working pressure, non-shock cold water. • Burst pressure is engineered minimum 3 times the working pressure.

D

C

A

T

B

Nominal Size mm / in 65 x 20 2½ x ¾ 65 x 25 2½x 1 65 x 32 2½ x 1¼ 80 x 20 3 x ¾ 80 x 25 3 x 1 80 x 32 3 x 1¼ 100 x 20 4 x ¾ 100 x 25 4 x 1 100 x 32 4 x 1¼

Hole Dia. +1.6, -0 / +0.063, -0 A B mm / in mm / in mm / in 30 66 40 1.18 2.60 1.57 30 66 40 1.18 2.60 1.57 45 73 40 1.77 2.87 1.57 30 73 45 1.18 2.87 1.77 30 73 45 1.18 2.87 1.77 45 84 45 1.77 3.31 1.77 30 86 60 1.18 3.39 2.36 30 86 60 1.18 3.39 2.36 45 97 60 1.77 3.81 2.36

Dimensions Bolt C D T* Size Weight mm / in mm / in mm / in in Kgs / Lbs 118 44 52 0.7 ⅜ x 2⅛ 4.65 1.73 2.05 1.5 118 44 49 0.7 ⅜ x 2⅛ 4.65 1.73 1.93 1.5 118 63 55 1.0 ⅜ x 2⅛ 4.65 2.48 2.15 2.2 130 44 58 0.7 ⅜ x 2⅛ 5.12 1.73 2.28 1.5 130 44 56 0.8 ⅜ x 2⅛ 5.12 1.73 2.20 1.8 130 63 66 1.0 ⅜ x 2⅛ 5.12 2.48 2.59 2.2 158 44 71 0.8 ⅜ x 2⅛ 6.22 1.73 2.80 1.8 158 44 79 0.8 ⅜ x 2⅛ 6.22 1.73 3.11 1.8 158 63 79 0.8 ⅜ x 2⅛ 6.22 2.48 3.11 1.8

*T: Take-out , Center of run to engaged pipe end (approx.)

Use a torque wrench and tighten the nuts to an approx. torque value of 5 ~ 9 lbs-ft (7 ~ 12 N-m). Excess torque may cause t failure.



www.shurt.com

Catalog 2011

MODEL

C726 Y - STRAINER FOR COPPER TUBING (cts) The Shurt C726 Y-Strainer can be installed quickly and easily with two mechanical couplings and the straight flow through design provides for lower pressure drop. Pressure-Temperature Rating Nom. Ratings

Working Pressure (Type K Copper Tubing)

Shell Test (Hydrostatic)


Class 150

300 psi @100°F 20 Bar @38°C

450 psi 32 Bar

EPDM: 230°F / 110°C


C

B

A

Nominal Size mm / in 50 2 65 2½ 80 3 100 4 150 6

Pipe O. D. mm / in 54.0 2.125 66.7 2.625 79.4 3.125 104.8 4.125 155.6 6.125

Max. Working Pressure A Bar / PSI mm / in 20 222 300 8.75 20 248 300 9.75 20 270 300 10.63 20 330 300 13.00 20 432 300 17.00


Dimensions B C mm / in mm / in 162 81 6.38 3.18 170 96 6.69 3.78 196 114 7.71 4.50 244 152 9.60 6.00 328 203 12.91 8.00

Drain Plug Size mm / in 15 ½ 15 ½ 15 ½ 25 1 25 1

www.shurt.com



Catalog 2011

MODEL

SJ-C300 BUTTERFLY VALVE FOR COPPER TUBING (cts) The Shurt Model SJ-C300 is a lever

copper alloy C90500 (88-10-0-2) or C89836

handle bronze body butterfly valve designed

Bismuth bronze which are UL classified in

for use with grooved copper tubing (CTS),

accordance with ANSI/NSF 61 and annex G

fittings and couplings. The lead-free

for potable water use.

bronze body conforms to ASTM B-584 Pressure-Temperature Rating Nom. Ratings CWP

Working Pressure (Type K Copper Tubing)

Shell Test @73°F / 23°C


300 psi @100°F 20 Bar @38°C

450 psi 32 Bar

EPDM: 230°F / 110°C

*Working pressure is for connection with roll-grooved Type K copper tubing. *Seat test: 100% working pressure.

D

B

A SJ-C300 butterfly valve installed in a hot water system



Pipe O. D. A mm / in mm / in 54 81 2.125 3.19 66.7 97 2.625 3.82 79.4 97 3.125 3.82 104.8 116 4.125 4.57 130.2 148 5.125 5.83 155.6 148 6.125 5.83


O. D.

A

C

B mm / in 135 5.31 149 5.87 163 6.42 208 8.19 248 9.77 274 10.79

Dimensions

C mm / in 57 2.45 73 2.87 83 3.27 111 4.37 136 5.36 163 6.42

D mm / in 254 10.0 254 10.0 254 10.0 254 10.0 254 10.0 254 10.0

www.shurt.com

Weight Kgs / Lbs 2.7 5.9 3.3 7.3 3.5 7.7 5.0 11.0 7.7 16.9 7.7 16.9

Section 9 AWWA Ductile Iron Series AWWA Ductile Iron Series..................................................................... 130 Radius Cut Groove Specifications....................................................... 130 AWWA Grooved Couplings & Flange Adapters

A505 Coupling.................................................................................. 131 A507 Transition Coupling................................................................. 132 A512 Flange Adapter........................................................................ 132

Grooved Fittings

A10 / A11 / A12 / A13 / A60 Elbows, Cap................................... 133 A20 / A25 / A50 / A10R Tee, Reducing Tee,

Concentric Reducer, Reducing Elbow................................................ 134

Catalog 2011

Catalog 2011

AWWA Ductile Iron Series Shurt offers a variety of grooved mechanical couplings and fittings for AWWA ductile iron pipe in sizes 3” to 24”. The Shurt coupling features a two-piece housing and GapSeal® gasket for a leaktight seal. Ductile iron pipe shall be cut-grooved to AWWA C-606 Table 2 and Table 3 - Radius Cut Groove Specifications. Rubber gaskets are specially compounded to seal on ductile iron surfaces and are available in three grades to meet your service requirement needs. See page 131 for details.

Radius Cut Groove Specification For Ductile Iron Pipe B R

A B T O.D.

C

Gasket Seating Surface (Column 3) The same coupling can be used either as a rigid t or a flexible t depending on the groove. Gasket seat "A Rigid" is for rigid ts and Gasket seat "A Flex." for flexible ts. The gasket seating surface shall be free from deep scores, marks, or ridges that could prevent a positive seal. Groove Diameter (Column 5) The 'C' diameters are average values. The groove must be of uniform depth around the entire pipe circumference. Radius (Column 6) The groove must be cut with a radius "R" at the corners of the groove to reduce stress concentration. Minimum Wall Thickness (Column 7) "T" is the minimum allowable wall thickness that may be cut-grooved; tolerances are to conform to ANSI /AWWA C151/A21.51.

AWWA Ductile Iron Pipe Pipe O. D. Nominal Size Basic Tolerance + - mm / in mm / in mm / in mm / in 80 100.6 +1.14 -1.14 3 3.96 +0.045 -0.045 100 121.9 +1.14 -1.14 4 4.80 +0.045 -0.045 150 175.3 +1.52 -1.52 6 6.90 +0.060 -0.060 200 229.9 +1.52 -1.52 8 9.05 +0.060 -0.060 250 281.9 +1.52 -1.52 10 11.10 +0.060 -0.060 300 335.3 +1.52 -1.52 12 13.20 +0.060 -0.060 350 388.6 +1.27 -2.03 14 15.30 +0.050 -0.080 400 442.0 +1.27 -2.03 16 17.40 +0.050 -0.080 450 495.3 +1.27 -2.03 18 19.50 +0.050 -0.080 500 548.6 +1.27 -2.03 20 21.60 +0.050 -0.080 600 655.3 +1.27 -2.03 24 25.80 +0.050 -0.080



Gasket Seat A Rigid Flex. +0/-0.51 +0.41/-1.19 +0/-0.02 +0.016/-0.047 mm / in mm / in 21.34 19.05 0.840 0.750 21.34 19.05 0.840 0.750 21.34 19.05 0.840 0.750 24.13 22.23 0.950 0.875 25.78 23.83 1.015 0.938 25.78 23.83 1.015 0.938 25.78 23.83 1.015 0.938 34.04 30.18 1.340 1.188 34.04 30.18 1.340 1.188 34.04 30.18 1.340 1.188 34.04 30.18 1.340 1.188

Groove Groove Dia. C Width B Tol. +0.79/-0.41 +0 Radius +0.031/-0.016 Basic +0 R mm / in mm / in mm / in mm / in 9.53 94.56 -0.51 3.05 0.375 3.723 -0.020 0.120 9.53 115.90 -0.51 3.05 0.375 4.563 -0.020 0.120 9.53 169.06 -0.51 3.05 0.375 6.656 -0.020 0.120 12.70 223.04 -0.64 3.68 0.500 8.781 -0.025 0.145 12.70 274.65 -0.64 3.68 0.500 10.813 -0.025 0.145 12.70 327.81 -0.76 3.68 0.500 12.906 -0.030 0.145 15.88 327.81 -0.76 4.19 0.625 14.969 -0.030 0.165 15.88 433.40 -0.76 4.19 0.625 17.063 -0.030 0.165 15.88 485.78 -0.76 4.70 0.625 19.125 -0.030 0.185 15.88 538.96 -0.76 4.70 0.625 21.219 -0.030 0.185 15.88 645.31 -0.76 4.70 0.625 25.046 -0.030 0.185

www.shurt.com

Min. Allow Wall Thick T mm / in 7.9 0.31 8.1 0.32 8.6 0.34 9.1 0.36 9.7 0.38 10.2 0.40 10.7 0.42 10.9 0.43 11.2 0.44 11.4 0.45 11.9 0.47

Catalog 2011

MODEL

A505 Coupling Shurt Model A505 couplings are

The Model A505 coupling is recommended

designed for connecting grooved ductile

for service up to 500 psi (35 bar) depending

iron pipe and fittings of ANSI/AWWA C151/

on the size. The GapSeal® gasket fits flush

A21.51, Class 53 or higher dimensions.

over the pipe ends and prevents fluids from

The same coupling can be used either

entering into the gasket cavity.

as a flexible coupling or a rigid coupling depending on the type of groove processed.

B

C

A

Nominal Size mm / in 80 3 100 4 150 6 200 8 250 10 300 12 350 14 400 16 450 18 500 20 600 24

Pipe O. D. mm / in 100.6 3.96 121.9 4.80 175.3 6.90 229.9 9.05 281.9 11.10 335.3 13.20 388.6 15.30 442.0 17.40 495.3 19.50 548.6 21.60 655.3 25.80

Max. Working Max. End Pressure Load Bar / PSI kN / Lbs 35 27.59 500 6200 35 40.50 500 9000 28 66.26 400 14950 28 113.92 400 25600 25 150.63 350 33850 25 211.50 350 47900 17 204.47 250 45950 17 264.33 250 59400 17 332.19 250 74650 10 244.31 150 54900 10 348.80 150 78400

Axial Bolts Displacement* size A mm / in No. in mm / in 0~2.4 141 2 ½x3 0~0.09 5.55 0~2.4 164 2 ⅝ x 3½ 0~0.09 6.46 0~2.4 218 2 ⅝ x 3½ 0~0.09 8.58 0~4.0 275 2 ¾ x 4¾ 0~0.16 10.83 0~4.0 332 2 ¾ x 4¾ 0~0.16 13.07 0~4.0 390 2 ⅞ x 6½ 0~0.16 15.35 0~4.0 441 4 1 x 3½ 0~0.16 17.36 0~6.4 504 4 1 x 3½ 0~0.25 19.84 0~6.4 560 4 1 x 3½ 0~0.25 22.05 0~6.4 610 4 1⅛ x 4 0~0.25 24.37 0~6.4 740 4 1⅛ x 4 0~0.25 29.14

Dimensions B mm / in 194 7.64 221 8.70 265 10.43 354 13.94 406 16.00 480 18.90 530 20.87 604 22.78 660 26.00 720 28.35 840 33.07

C mm / in 56 2.20 57 2.25 57 2.25 67 2.64 70 2.76 70 2.76 73 2.88 89 3.50 89 3.50 89 3.50 89 3.50

Weight Kgs / Lbs 2.5 5.5 3.3 7.3 4.4 9.7 8.5 18.7 11.0 24.2 14.0 30.8 16.0 35.2 26.4 58.0 35.0 77.0 38.0 83.6 49.0 107.8

Pressure ratings listed are based on radius cut-grooved Thickness Class 53 or higher pipe. *only when connected on flexible radius groove.

Special gaaskets for AWWA ductile iron pipe Grade

Temp. Range

S

-20°F to + 180°F (-29°C to +82°C)

Compound

Color Code

General Service Recommendations

Specially formulated to seal on ductile iron pipe iron

surfaces. Recommended for petroleum products, air with oil vapors, vegetable and mineral oils within the

Nitrile

specified temperature range; except hot dry air over 60°C (+140°F) and water over 65°C (+150°F)

Red Stripe

NOT RECOMMENDED FOR HOT WATER SERVICES. Specially formulated to seal on ductile iron pipe

M

L

-20°F to + 200°F (-29°C to +93°C)

-30°F to + 350°F (-34°C to +177°C)

surfaces. Recommended for water service plus a variety of dilute acids, oil-free air and other chemical services

Halogenated Butyl

within the specified temperature range. The compound

is UL classified per ANSI/NSF61 for potable water

Brown Stripe

applications.

NOT RECOMMENDED FOR HOT WATER SERVICES.

Recommended for dry heat, air without hydrocarbons to

Silicone

350°F (177°C) and certain chemical services.

Red Gasket


www.shurt.com


Catalog 2011

MODEL

A507 Transition Coupling The Model A507 Transition Coupling provides for a direct connection between grooved end IPS steel pipe and grooved end AWWA ductile iron pipe, fittings and or valves. The A507 will accommodate roll or cut grooved IPS steel pipe and rigid or flexible AWWA ductile iron cut grooves.

C

B

A


IPS Steel mm / in 88.9 3.500 114.3 4.500 168.3 6.625 219.1 8.625 273.0 10.750 323.9 12.750

Pipe OD AWWA Ductile Iron mm / in 100.6 3.96 121.9 4.80 175.3 6.90 229.9 9.05 281.9 11.10 335.3 13.20

C

B

A

Max. Working Max. End Pressure Load Bar / PSI kN / Lbs 35 21.41 500 4810 35 35.38 500 7950 28 61.32 400 13780 28 103.99 400 23370 25 155.96 350 33850 25 220.64 350 47870

Axial Bolts Displacement size A mm / in in mm / in 1 140 ½ x 2¾ 0.03 5.50 1 162 ⅝ x 3½ 0.03 6.38 1 214 ⅝ x 3½ 0.03 8.44 1 279 ¾ x 4¾ 0.03 11.00 1 334 ⅞ x 6½ 0.03 13.13 1 391 ⅞ x 6½ 0.03 15.38

Dimensions B mm / in 187 7.38 229 9.00 283 11.13 353 13.88 419 16.50 481 18.94

C mm / in 53 2.07 56 2.19 59 2.31 67 2.63 67 2.63 67 2.63

Weight Kgs / Lbs 2.2 4.8 2.9 6.4 3.9 8.6 7.6 16.7 11.3 24.9 13.0 28.6

MODEL

A512 Flange Adapter The Model A512 Flange Adapter provides for the direct connection between AWWA ductile iron radius pipe grooves and flanged

A

C

components. The two part flange features integral closure tabs to aid in assembly. Note: As with other flange adapters the

B

A512 requires a sufficient smooth flat mating area for proper sealing, please reference

the A512 cut sheet or Shurt for details. AWWA D. I. Pipe Nominal Size Pipe OD mm / in mm / in 80 100.6 3 3.96 100 121.9 4 4.80 150 175.3 6 6.90 200 229.9 8 9.05 250 281.9 10 11.10 300 335.3 12 13.20

Max. Working Max. End Bolts Pressure Load size A Bar / PSI kN / Lbs No. in mm / in 17 13.80 191 4 ⅝x3 250 3100 7.50 17 20.03 229 8 ⅝x3 250 4500 9.00 17 41.39 279 8 ¾ x 3½ 250 9300 11.00 17 71.20 343 8 ¾ x 3½ 250 16000 13.50 17 105.47 406 12 ⅞x4 250 23700 16.00 17 151.30 483 12 7/8 x 4 250 34000 19.00

Dimensions B mm / in 152 6.00 191 7.50 241 9.49 298 11.75 362 14.25 432 17.00

Flange drilling to ANSI B16.1 Class 125.



www.shurt.com

C mm / in 24 0.94 24 0.94 25 1.00 29 1.13 30 1.19 32 1.25

Weight Kgs / Lbs 3.9 8.6 4.5 9.9 5.4 12.0 8.6 18.9 11.5 25.3 15.6 34.4

AWWA GROOVED FITTINGS

Catalog 2011

MODEL

A10 90° ELBOW A11 45° ELBOW A12 22½° ELBOW A13 11¼° ELBOW A60 CAP Shurt AWWA grooved end fittings are

C-110 for wall thickness. Pressure ratings

supplied with rigid radius grooves as per

are 500 psi (35 Bar). Fittings are supplied

ANSI / AWWA C-606. The fittings also

painted black. Other surface finish options

conform to ANSI A21.10 / AWWA C-110

including 'non-coated' and cement/mortar

for center to end (C to E) dimensions and

lining Type II are available on request.

AWWA C-153 or ANSI A21.10 / AWWA

E-E

C-E

E-E

AWWA D. I. Pipe Nom. Size OD mm / in mm / in 80 100.6 3 3.96 100 121.9 4 4.80 150 175.3 6 6.90 200 229.9 8 9.05 250 281.9 10 11.10 300 335.3 12 13.20

C-E

A10 90˚ Elbow

A11 45˚ Elbow

A10 90° Elbow C - E Weight mm / in Kgs / Lbs 140 4.2 5.50 9.2 165 5.6 6.50 12.2 203 10.7 8.00 23.5 229 18.9 9.00 41.6 279 29.5 11.00 64.0 305 42.8 12.00 94.2

A11 45° Elbow C - E Weight mm / in Kgs / Lbs 76 2.6 3.00 5.8 102 4.2 4.00 9.2 127 8.0 5.00 17.6 140 15.0 5.50 33.0 165 20.4 6.50 44.9 191 32.7 7.50 72.0


C-E A12 22½° Elbow A12 22½° Elbow C - E Weight mm / in Kgs / Lbs 76 5.7 3.00 12.5 102 5.2 4.00 11.5 127 11.3 5.00 25.0 140 17.9 5.50 39.5 165 30.4 6.50 67.0 191 49.0 7.50 108.0

C-E A13 11¼° Elbow

4"-8" 10"-12" A60 Cap

A13 11¼° Elbow C - E Weight mm / in Kgs / Lbs 76 4.1 3.00 9.0 102 5.2 4.00 11.5 127 9.8 5.00 21.5 140 17.7 5.50 39.0 165 34.9 6.50 77.0 191 54.0 7.50 120.0

A60 Cap

www.shurt.com

E - E mm / in 29 1.16 29 1.16 29 1.16 34 1.34 39 1.53 39 1.53

Weight Kgs / Lbs 1.2 2.6 1.6 3.5 3.1 6.8 5.9 13.0 10.0 22.0 11.2 24.6


AWWA GROOVED FITTINGS

Catalog 2011

MODEL

A20 Tee

AWWA D. I. Pipe Nom. Size O. D. mm / in mm / in 80 100.6 3 3.96 100 121.9 4 4.80 150 175.3 6 6.90 200 229.9 8 9.05 250 281.9 10 11.10 300 335.3 12 13.20

C-E C-E

A 20 Tee C - E Weight mm / in Kgs / Lbs 140 6.1 5.50 13.4 165 8.4 6.50 18.5 203 15.9 8.00 35.0 229 27.4 9.00 60.3 279 45.7 11.00 110.5 305 61.7 12.00 136.0

A20 Tee

MODEL

A25 Reducing Tee A50 Concentric Reducer A10R Reducing Elbow

C-E C-E C-E

E-E

A25 Reducing Tee

Nom. Size mm / in 100 x 80 4 x 3 150 x 100 6 x 4 200 x 100 8 x 4 200 x 150 8 x 6 250 x 100 10 x 4 250 x 150 10 x 6 250 x 200 10 x 8 300 x 100 12 x 4 300 x 150 12 x 6 300 x 200 12 x 8 300 x 250 12 x 10


AWWA D. I. Pipe

OD mm / in 121.9 x 100.6 4.80 x 3.96 175.3 x 121.9 6.90 x 4.80 229.9 x 121.9 9.05 x 4.80 229.9 x 175.3 9.05 x 6.90 281.9 x 121.9 11.10 x 4.80 281.9 x 175.3 11.10 x 6.90 281.9 x 229.9 11.10 x 9.05 335.3 x 121.9 13.20 x 4.80 335.3 x 175.3 13.20 x 6.90 335.3 x 229.9 13.20 x 9.05 335.3 x 281.9 13.20 x 11.10

A25 Reducing Tee

C - E mm / in 165 6.50 203 8.00 229 9.00 229 9.00 279 11.00 279 11.00 279 11.00 305 12.00 305 12.00 305 12.00 305 12.00


Weight Kgs / Lbs 8.5 18.8 15.2 33.3 23.3 51.2 26.0 57.2 54.4 120.0 58.1 128.0 59.0 130.0 50.8 112.0 81.7 180.0 84.4 186.0 87.1 192.0

A50 Conc. Reducer

A50 Concentric Reducer E - E Weight mm / in Kgs / Lbs 178 3.5 7.00 7.7 229 6.5 9.00 14.3 279 10.9 11.00 23.9 279 12.6 11.00 27.7 305 19.1 12.00 42.0 305 20.9 12.00 46.0 305 18.8 12.00 41.3 356 27.2 14.00 60.0 356 31.8 14.00 70.0 356 33.6 14.00 74.0 356 38.1 14.00 84.0

A10R Reducing Elbow

A10R 90° Reducing Elbow C - E Weight mm / in Kgs / Lbs 165 5.5 6.50 12.1 203 11.4 8.00 25.1 229 19.8 9.00 43.6 229 19.0 9.00 41.8 --- ----- --279 34.9 11.00 77.0 279 39.9 11.00 88.0 --- ----- --305 49.9 12.00 110.0 305 57.2 12.00 126.0 305 68.0 12.00 150.0

www.shurt.com

Section 10 Technical Information Pipe End Preparation............................................................................. 136 Roll Grooving Dimensions for IPS, BS & AS pipe.............................. 137 Roll Grooving Dimensions for ISO pipe.............................................. 138 Roll Grooving Dimensions for KS and JIS pipe.................................. 138 Cut Grooving Dimensions for IPS, BS, AS, ISO, JIS & KS pipe......... 139 Roll Grooving Machines – Ratings and Capacity............................... 140 Typical Applications – Flexible Couplings (General Applications)........... 142 Anchoring, Hanging and s....................................................... 144 Gasket Selection ................................................................................... 147 Chemical Resistance Information....................................................... 148 Fire Protection Services........................................................................ 151 Approved Pressure Ratings by UL and FM........................................ 152 Typical Applications – Flexible Couplings – Sprinkler Systems (NFPA 13)........................................................................................... 154 Project Pictures...................................................................................... 156 and Conditions............................................................................ 160

Catalog 2011

Catalog 2011

Pipe End Preparation How to process roll-grooves

Shurt grooved piping systems require the processing of a roll or cut groove to the pipe ends being connected. The engagement of the housing keys in the grooves is integral in providing a secure and leak-tight t. It is essential that the grooves are properly processed for optimum t performance.

applied on the ground surface. Shurt strongly recommends the processing of cut-grooves on heavy or thick wall pipe.

No or very little protrusion Thicker than 9.5mm (0.375”)

Housing

Pipe

Key

Plain end pipe and beveled end pipe

While plain-end pipe is preferred, the use of beveled end pipe is acceptable providing that the wall thickness is .375”/9.5mm or thinner

Rubber gasket

and the bevel is 37½ ±2½° or 30° as specified in ANSI B16.25 and

Groove

Full engagement

Nominal pipe size

Plain-end

ASTM A-53 respectively.

Plain-end pipe

Shurt couplings and fittings are identified by the nominal IPS

37½° or 30°

pipe size in inches or nominal diameter of pipe (DN) in millimeters. Always check the actual O.D. of the pipe and fittings to be connected,

Beveled-end Pipe ( ANSI B16.25 / ASTM A- 53 )

as in some markets it is customary to refer to different O.D. pipes with the same nominal size.

ERW pipe

ERW pipe is one of the most popular types of pipe used today.

Roll groove profile

Depending on the individual pipe and manufacturer, welding beads

Roll grooves should be as defined To achieve optimum A as possible. B

may remain on the surface (inside and outside) of the pipe. Always

When processing a roll groove the machine operator should manage

rattling of the roll grooving machine resulting in inaccurate grooves.

t performance the “K” dimension should be as small as possible. the feed pressure of the upper roll set so as to achieve the best

possible groove profile.

C A K

B B1

remove harmful weld beads near the pipe ends as they can cause

Galvanized pipe

Galvanized pipe is acceptable as long as the gasket seating surface is smooth and free from scale and imperfections that could affect gasket sealing. Whenever you remove welding beads or projections from the sealing surface of galvanized pipe, use caution so as to not

C

Applicable pipe wall thickness

Roll grooves are generally applicable to .375”/9.5mm thick or thinner wall carbon steel pipe, stainless steel pipe, copper tube, aluminum pipe and PVC pipe depending on the type of roll-grooving machine and roll set being used. Different wall thicknesses and sizes require the use of different roll sets. the roll groove machine manufacturer for additional information.

over-grind the surface. After grinding, always apply a proper rustprevention coating to this area.

Spiral welded pipe

Spiral welded pipe may be used as long as the weld beads are removed from the gasket seating surface. It is also acceptable and recommended to weld a grooved end nipple to the pipe end as shown below. Whenever you remove weld beads or projections from the gasket seating surface, use caution so as to not over-grind the surface. After grinding, always apply a proper rust-prevention coating to this area.

Heavy wall pipe

Welded

When you attempt to roll-groove pipe thicker than .375”/9.5mm, the metal may deform and heap up on both sides of the groove rather than radially deforming and protruding on the inside of the pipe. The extra heaped metal could lead to t failure. In such a case, you should grind off any such extra metal to achieve a flat and Spiral pipe

smooth sealing surface. A proper rust preventative coating must be



Weld beads shall be removed Spiral pipe with a grooved nipple

www.shurt.com

Catalog 2011

Roll Grooving Dimensions for ANSI B36.10, BS 1387 (M) & AS-1074 (M) Pipe t

A B

Basic roll groove dimensions conform to ANSI/AWWA C606-06 Table 5 with slightly adjusted tolerances to incorporate international standards including CSA B242, ISO/FDIS 6152-12, VdS 2100-6en

C

O.D.

and JPF MP-006.

d

Nominal Size Basic mm / in mm / in 20 26.7 ¾ 1.050 25 33.4 1 1.315 32 42.2 1¼ 1.660 40 48.3 1½ 1.900 50 60.3 2 2.375 65 73.0 2½ 2.875 76.1 76.1mm 3.000 80 88.9 3 3.500 90 101.6 3½ 4.000 100 114.3 4 4.500 139.7 139.7mm 5.500 125 141.3 5 5.563 165.1 165.1mm 6.500 150 168.3 6 6.625 200 219.1 8 8.625 250 273.0 10 10.750 300 323.9 12 12.750 350 355.6 14 14.000 400 406.4 16 16.000 450 457.2 18 18.000 500 508.0 20 20.000 550 559.0 22 22.000 600 609.6 24 24.000

Pipe O.D. Tolerance mm / in mm / in +0.25 -0.25 +0.010 -0.010 +0.33 -0.33 +0.013 -0.013 +0.41 -0.41 +0.016 -0.016 +0.48 -0.48 +0.019 -0.019 +0.61 -0.61 +0.024 -0.024 +0.74 -0.74 +0.029 -0.029 +0.76 -0.76 +0.030 -0.030 +0.89 -0.79 +0.035 -0.031 +1.02 -0.79 +0.040 -0.031 +1.02 -0.79 +0.040 -0.031 +1.40 -0.79 +0.050 -0.031 +1.42 -0.79 +0.056 -0.031 +1.60 -0.79 +0.063 -0.031 +1.60 -0.79 +0.063 -0.031 +1.60 -0.79 +0.063 -0.031 +1.60 -0.79 +0.063 -0.031 +1.60 -0.79 +0.063 -0.031 +1.60 -0.79 +0.063 -0.031 +1.60 -0.79 +0.063 -0.031 +1.60 -0.79 +0.063 -0.031 +1.60 -0.79 +0.063 -0.031 +1.60 -0.79 +0.063 -0.031 +1.60 -0.79 +0.063 -0.031

A ±0.76 ±0.030 mm / in 15.88 0.625 15.88 0.625 15.88 0.625 15.88 0.625 15.88 0.625 15.88 0.625 15.88 0.625 15.88 0.625 15.88 0.625 15.88 0.625 15.88 0.625 15.88 0.625 15.88 0.625 15.88 0.625 19.05 0.750 19.05 0.750 19.05 0.750 23.83 0.938 23.83 0.938 25.40 1.000 25.40 1.000 25.40 1.000 25.40 1.000

B ±0.76 ±0.030 mm / in 7.14 0.281 7.14 0.281 7.14 0.281 7.14 0.281 8.74 0.344 8.74 0.344 8.74 0.344 8.74 0.344 8.74 0.344 8.74 0.344 8.74 0.344 8.74 0.344 8.74 0.344 8.74 0.344 11.91 0.469 11.91 0.469 11.91 0.469 11.91 0.469 11.91 0.469 11.91 0.469 11.91 0.469 11.91 0.469 12.70 0.500

1. Pipe ends must be square cut. See table for maximum allowable tolerances from squareAcceptable max. pipe O.D. cut ends.

PIPE

Pipe Sizes

0.8mm ( 0.030” )

1.2mm ( 0.045” )

8” ~ above

G

1.6mm ( 0.060” )


Groove Depth d (ref.) mm / in 1.42 0.056 1.60 0.063 1.60 0.063 1.60 0.063 1.60 0.063 1.98 0.078 1.93 0.075 1.98 0.076 2.11 0.083 2.11 0.083 2.11 0.083 2.11 0.083 2.16 0.085 2.16 0.085 2.34 0.092 2.39 0.094 2.77 0.109 2.77 0.109 2.77 0.109 2.77 0.109 2.77 0.109 4.37 0.132 4.37 0.172

Max. Allowed Flare Dia. mm / in 29.2 1.15 36.3 1.43 45.0 1.77 51.1 2.01 63.0 2.48 75.7 2.98 77.7 3.06 91.4 3.60 104.1 4.10 116.8 4.60 141.7 5.578 143.8 5.66 167.0 6.574 170.9 6.73 223.5 8.80 277.4 10.92 328.2 12.92 358.1 14.10 408.9 16.10 461.3 18.16 512.1 20.16 563.9 22.20 614.7 24.20

Housing segmen

Upper limit Center line Lower limit

Pipe O.D. check (Before grooving)

2. The gasket seating surface `A' shall be free from deep scores, marks, or ridges that would prevent a positive seal. 3. The `C' dimensions are average values. The groove must be of uniform depth around the entire circumference. Use a Shurt groove gage or rule to check the groove diameter. 4. The `t' is the minimum allowable wall thickness that may be roll-grooved.

Min. Wall t mm / in 1.65 0.065 1.65 0.065 1.65 0.065 1.65 0.065 1.65 0.065 2.11 0.083 2.30 0.090 2.11 0.083 2.11 0.083 2.11 0.083 2.90 0.114 2.77 0.109 2.90 0.114 2.77 0.109 2.77 0.109 3.40 0.134 3.96 0.156 3.96 0.156 4.19 0.165 4.19 0.165 4.78 0.188 4.78 0.188 4.78 0.188

Acceptance range

G (max)

Up to 3½” 4 ~ 6”

C +0.00 +0.000 mm / in 23.83-0.38 0.938-0.015 30.23-0.38 1.190-0.015 38.99-0.38 1.535-0.015 45.09-0.38 1.775-0.015 57.15-0.38 2.250-0.015 69.09-0.46 2.720-0.018 72.260-0.46 2.844-0.018 84.94-0.46 3.344-0.018 97.38-0.51 3.834-0.020 110.08-0.51 4.334-0.020 135.48-0.51 5.333-0.020 137.03-0.56 5.395-0.022 160.90-0.56 6.334-0.022 163.96-0.56 6.455-0.022 214.40-0.64 8.441-0.025 268.27-0.69 10.562-0.027 318.29-0.76 12.531-0.030 350.04-0.76 13.781-0.030 400.84-0.76 15.781-0.030 451.64-0.76 17.781-0.030 502.44-0.76 19.781-0.030 550.06-0.76 21.656-0.030 600.86-0.76 23.656-0.030

Groove Gage

Groove Rule

Quick check with a housing segment

5. The `d' is for reference use only. The groove depth shall be determined by the groove diameter `C'. 6. Flare Diameter: The pipe end that may flare when the groove is rolled shall be within this limit when measured at the extreme end of the pipe.

www.shurt.com


Catalog 2011

Roll Grooving Dimensions per ISO/FDIS 6182-12 Table 1

For ISO 4200:1991 Plain-end Steel Tubes, Welded and Seamless (Superseding BS1387 and DIN 2440 & DIN 2448) A

B t

ØF ØC

ØOD

D

Figure 1 - Roll grooved-end dimensional reference points for Table 1 Dimensions in millimeters

Nominal size 25 32 40 50 65 65 80 90 100 100 125 125 125 150 150 150 200 250 300

specificationsa

Pipe or tube Outside diameter (OD) Actual Tolerance size 33,7 +0,41 / -0,68 42,4 +0,50 / -0,60 48,3 +0,44 / -0,52 60,3 ±0,61 73,0 ±0,74 76,1 ±0,76 88,9 +0,89 / -0,79 101,6 +1,02 / -0,79 108,0 +1,07 / -0,70 114,3 +1,14 / -0,79 133,9 +1,32 / -0,70 139,7 +1,40 / -0,79 141,3 +1,42 / -0,79 159,0 +1,60 / -0,79 165,1 +1,60 / -0,79 168,3 +1,60 / -0,79 219,1 +1,60 / -0,79 277,4 +1,60 / -0,79 328,2 +1,60 / -0,79

Dimensional Gasket seat Gasket width Grooved diameter C A B Actual Tolerance ±0.76 ±0.76 size 15,88 7,14 30,23 0 / -0,38 15,88 7,14 38,99 0 / -0,38 15,88 7,14 45,09 0 / -0,38 15,88 8,74 57,15 0 / -0,38 15,88 8,74 69,09 0 / -0,46 15,88 8,74 72,26 0 / -0,46 15,88 8,74 84,94 0 / -0,46 15,88 8,74 97,38 0 / -0,51 15,88 8,74 103,73 0 / -0,51 15,88 8,74 110,08 0 / -0,51 15,88 8,74 129,13 0 / -0,51 15,88 8,74 135,48 0 / -0,51 15,88 8,74 137,03 0 / -0,56 15,88 8,74 154,50 0 / -0,56 15,88 8,74 160,90 0 / -0,56 15,88 8,74 163,96 0 / -0,56 19,05 11,91 214,40 0 / -0,64 19,05 11,91 268,28 0 / -0,69 19,05 11,91 318,29 0 / -0,76

Groove depth Db 1,70 1,70 1,60 1,60 1,98 1,93 1,98 2,11 2,11 2,11 1,93 2,11 2,13 2,20 2,16 2,16 2,34 2,39 2,77

Wall Thickness T Min. allow. 1,8 1,8 1,8 1,8 2,3 2,3 2,3 2,3 2,3 2,3 2,9 2,9 2,9 2,9 2,9 2,9 2,9 3,6 4,0

Flare F Max. Dia. 34,5 43,3 49,4 62,2 75,2 77,7 90,6 103,4 109,7 116,2 134,9 141,7 143,5 161,0 167,1 170,7 221,5 275,4 326,2

a See Figure 1 for dimensional diagram b Dimension for reference only, groove diameter is determined by C.

Roll Grooving Dimensions for KS D3507 & JIS G3452 Carbon Steel Pipe L

F

d

W

G

O.D.

C=πG

A mm 25A 32A 40A 50A 65A 80A 100A 125A 150A 200A 250A 300A

Nominal size Pipe B O.D. mm mm 1 34.0 1¼ 42.7 1½ 48.6 2 60.5 2½ 76.3 3 89.1 4 114.3 5 139.8 6 165.2 8 216.3 10 267.4 12 318.5

Gasket Seat L +0.76* mm 16.0 16.0 16.0 16.0 16.0 16.0 16.0 16.0 16.0 19.0 19.0 19.0

Groove Diameter: Groove diameter “G” are only applicable to pipe sizes 150A or smaller. Grooves for 200A thru 300A are to be determined by the groove circumference. Groove Depth: The “d” is for reference use only. Flare Diameter: The maximum flare diameters (f) are target values.

Groove Groove Dia. G Width W Basic Tolerance +0.76* +0.00* mm mm mm 7.1 30.4 -0.38 7.1 39.1 -0.38 7.1 45.0 -0.38 8.7 56.9 -0.38 8.7 72.2 -0.46 8.7 84.9 -0.46 8.7 110.1 -0.51 8.7 135.5 -0.56 8.7 160.8 -0.56 11.9 211.6 -0.64 11.9 262.6 -0.69 11.9 312.9 -0.76

Groove Circumference C mm mm 95.5 0 / -3.1 122.8 0 / -3.1 141.4 0 / -3.1 178.8 0 / -3.1 226.8 0 / -3.1 266.7 0 / -3.1 345.9 0 / -3.1 425.7 0 / 3.1 505.2 0 / -3.1 664.8 0 / -3.1 825.0 0 / -3.1 983.0 0 / -3.1

The tolerance for the JIS & KS pipe has a little difference.



www.shurt.com

Groove Depth d (ref) mm 1.80 1.80 1.80 1.80 2.05 2.10 2.10 2.15 2.20 2.35 2.40 2.80

Flare f mm 35.5 44.2 50.1 62.0 77.8 90.6 116.8 142.3 167.7 219.8 270.9 322.0

Catalog 2011

Cut Grooving Dimensions for IPS, BS, AS, ISO, JIS & KS Pipe A

t B

C

O.D.

d

1

Nominal Size Basic mm / in mm / in 20 26.7 ¾ 1.050 25 33.4 1 1.315 32 42.2 1¼ 1.660 40 48.3 1½ 1.900 50 60.3 2 2.375 65 73.0 2½ 2.875 76.1 76.1mm 3.000 80 88.9 3 3.500 101.6 101.6mm 4.000 108.0 108.0mm 4.250 100 114.3 4 4.500 125 141.3 5 5.563 133.0 133.0mm 5.250 139.7 139.7mm 5.500 159.0 159.0mm 6.250 165.1 165.1mm 6.500 150 168.3 6 6.625 200 219.1 8 8.625 250 273.0 10 10.750 300 323.9 12 12.750 216.3 200 JIS 8.516 267.4 250 JIS 10.528 318.5 300 JIS 12.539 350 355.6 14 14.000 400 406.4 16 16.000 450 457.2 18 18.000 500 508.0 20 20.000 550 558.8 22 22.000 600 609.6 24 24.000

Gasket Seating Surface (Column 3): The gasket seating surface shall be free from deep scores, marks, or ridges that could prevent a positive seal. Groove Width (Column 4): Groove width is to be measured between vertical flanks of the groove side walls. Groove Diameter (Column 5): The 'C' diameters are average values. The groove must be of uniform depth around the entire pipe circumference. Minimum Wall Thickness (Column 6): The 't' is the minimum allowable wall thickness that may be cut-grooved. Groove Depth (Column 7): The 'd' is for reference use only. The groove dimension shall be determined by the groove diameter 'C'.

2

3

4

5

Pipe O. D. Tolerance mm / in mm / in +0.25 -0.25 +0.010 -0.010 +0.33 -0.33 +0.013 -0.013 +0.41 -0.41 +0.016 -0.016 +0.48 -0.48 +0.019 -0.019 +0.61 -0.61 +0.024 -0.024 +0.74 -0.74 +0.029 -0.029 +0.76 -0.76 +0.030 -0.030 +0.89 -0.79 +0.035 -0.031 +1.02 -0.79 +0.040 -0.031 +1.04 -0.79 +0.043 -0.031 +1.14 -0.79 +0.045 -0.031 +1.42 -0.79 +0.056 -0.031 +1.70 -0.79 +0.053 -0.031 +1.42 -0.79 +0.056 -0.031 +1.60 -0.79 +0.063 -0.031 +1.57 -0.79 +0.065 -0.031 +1.60 -0.79 +0.063 -0.031 +1.60 -0.79 +0.063 -0.031 +1.60 -0.79 +0.063 -0.031 +1.60 -0.79 +0.063 -0.031 +1.60 -0.79 +0.063 -0.031 +1.60 -0.79 +0.063 -0.031 +1.60 -0.79 +0.063 -0.031 +1.60 -0.79 +0.063 -0.031 +1.60 -0.79 +0.063 -0.031 +1.60 -0.79 +0.063 -0.031 +1.60 -0.79 +0.063 -0.031 +1.60 -0.79 +0.063 -0.031 +1.60 -0.79 +0.063 -0.031

A ±0.79 ±0.031 15.88 0.625 15.88 0.625 15.88 0.625 15.88 0.625 15.88 0.625 15.88 0.625 15.88 0.625 15.88 0.625 15.88 0.625 15.88 0.625 15.88 0.625 15.88 0.625 15.88 0.625 15.88 0.625 15.88 0.625 15.88 0.625 15.88 0.625 19.05 0.750 19.05 0.750 19.05 0.750 19.05 0.750 19.05 0.750 19.05 0.750 23.83 0.938 23.83 0.938 25.40 1.000 25.40 1.000 25.40 1.000 25.40 1.000

B ±0.79 ±0.031 7.95 0.313 7.95 0.313 7.95 0.313 7.95 0.313 7.95 0.313 7.95 0.313 7.95 0.313 7.95 0.313 7.95 0.313 9.53 0.375 9.53 0.375 9.53 0.375 9.53 0.375 9.53 0.375 9.53 0.375 9.53 0.375 9.53 0.375 11.13 0.438 12.70 0.500 12.70 0.500 11.13 0.438 12.70 0.500 12.70 0.500 12.70 0.500 12.70 0.500 12.70 0.500 12.70 0.500 14.30 0.563 14.30 0.563

C ±0.00 ±0.000 23.83-0.38 0.938-0.015 30.23-0.38 1.190-0.015 38.99-0.38 1.535-0.015 45.09-0.38 1.775-0.015 57.15-0.38 2.250-0.015 69.09-0.38 2.720-0.018 72.26-0.46 2.845-0.018 84.94-0.46 3.344-0.018 97.38-0.51 3.834-0.020 103.73-0.51 4.084-0.020 110.08-0.51 4.334-0.020 137.03-0.56 5.395-0.022 129.13-0.51 5.084-0.020 135.48-0.51 5.334-0.020 154.43-0.76 6.080-0.030 160.90-0.56 6.335-0.022 163.96-0.56 6.455-0.022 214.40-0.64 8.441-0.025 268.27-0.69 10.562-0.027 318.29-0.76 12.531-0.030 211.60-0.64 8.331-0.025 262.60-0.69 10.339-0.027 312.90-0.76 12.319-0.030 350.04-0.76 13.781-0.030 400.84-0.76 15.781-0.030 451.64-0.76 17.781-0.030 502.44-0.76 19.781-0.030 550.06-0.76 21.656-0.030 600.86-0.76 23.656-0.030


6

Min. Wall t mm / in 2.87 0.113 3.38 0.133 3.56 0.140 3.68 0.145 3.91 0.154 4.78 0.188 4.78 0.188 4.78 0.188 4.78 0.188 5.16 0.203 5.16 0.203 5.16 0.203 5.16 0.203 5.16 0.203 5.56 0.219 5.16 0.203 5.56 0.219 6.05 0.238 6.35 0.250 7.09 0.279 6.05 0.238 6.35 0.250 7.09 0.279 7.14 0.281 7.92 0.312 7.92 0.312 7.92 0.312 9.53 0.375 9.53 0.375

www.shurt.com

7 Groove Depth d (ref.) mm / in 1.42 0.056 1.60 0.063 1.60 0.063 1.60 0.063 1.60 0.063 1.98 0.078 1.98 0.078 1.98 0.078 1.98 0.078 2.11 0.083 2.11 0.083 2.11 0.083 1.93 0.076 2.11 0.083 2.20 0.087 2.16 0.085 2.16 0.085 2.34 0.092 2.39 0.094 2.77 0.109 2.34 0.092 2.39 0.094 2.77 0.109 2.77 0.109 2.77 0.109 2.77 0.109 2.77 0.109 4.37 0.172 4.37 0.172


Catalog 2011

Roll Grooving Machines and Tools – Ratings & Capacity Tool Model Pipe Pipe Pipe size No. Material Schedule Range SHURT® Carbon Steel Sch. 10 1" - 12" Sch. 40, STD 1" - 6" DSC-002 Stainless Sch. 10S 1" - 10"

Roll Set

(Standard) 2" - 6" Upper roll, Sch. 10 & Sch. 40 (STD) (Standard) 2" - 3" Bottom roll, Sch. 10 & Sch. 40 (STD) (Standard) 4" - 6" Bottom roll, Sch. 10 & Sch. 40 (STD) (Standard) 8" - 12" Upper & bottom rolls, Sch. 10 (Optional) 1" - 1 1/2" Upper roll, Sch. 40 (STD) (Optional) 1" - Bottom roll, Sch. 40 (STD) (Optional) 1 1/4" - 1 1/2" Bottom roll, Sch. 40 (STD) (Optional) 2" - 6" Upper roll, Sch. 10S Stainless (Optional) 2" - 3" Bottom roll, Sch. 10S Stainless (Optional) 4" - 6" Bottom roll, Sch. 10S Stainless (Optional) 8" - 10" Upper & bottom rolls, Sch. 10S Stainless

SHURT® Carbon Steel Sch. 10 8” ~ 24” .375" wall (STD) 8" - 24" DSC-003 Stainless Sch. 10S 8" - 24"

(Standard) 8" - 12" Upper & bottom rolls, Sch. 10 & STD (Standard) 14" - 16" Upper & bottom rolls, Sch. 10 & STD (Standard) 18" - 20" Upper & bottom rolls, Sch. 10 & STD (Standard) 22" - 24" Upper & bottom rolls, Sch. 10 & STD

Carbon Steel RG-150A

(Standard) 2" - 6" Sch. 10 & Sch. 40 steel

Sch. 10 1” ~ 16” Sch. 40 1” ~ 12” (w/ automatic pump) Stainless Sch. 5S & 10S RG-150 (w/ hand pump) .375” wall 1" - 6"

(Optional) 8" - 12" Upper & bottom rolls, Sch. 40 (Optional) 14" - 16" Upper & bottom rolls, Sch. 40 (Optional) 8" - 12" Upper & bottom rolls, Sch. 10S Stainless (Optional) 14" - 16" Upper & bottom rolls, Sch. 10S Stainless (Optional) 18" - 20" Upper & bottom rolls, Sch. 10S Stainless (Optional) 22" - 24" Upper & bottom rolls, Sch. 10S Stainless

(Optional) 8" Sch. 10 & 40, 10" - 12" Sch. 10 steel (Optional) 1 " - 1 1/2" Sch. 10 & 40 steel (Optional) 10" - 12" Sch. 40 & STD steel (Optional) 14" - 16" Sch. 10 steel (Optional) 2 " - 3" Sch. 5S & 10S stainless (Optional) 3 " - 6" Sch. 5S & 10S stainless

Carbon Steel Sch. 10 1” ~ 16” (Standard) 2" - 6" Sch. 10 & Sch. 40 steel RG-RH Sch. 40 1” ~ 12” (Optional) 8" Sch. 10 & 40, 10" - 12" Sch. 10 steel Stainless Sch. 5S &10S (Optional) 1 " - 1 1/2" Sch. 10 & 40 steel .134"(3.4mm) wall 1" - 6" (Optional) 10" - 12" Sch. 40 & STD steel (Optional) 14" - 16" Sch. 10 steel (Optional) 1 " - 1 1/2" Sch. 5S & 10S stainless (Optional) 2 " - 3" Sch. 5S & 10S stainless (Optional) 3 " - 6" Sch. 5S & 10S stainless (to use with Rex 2-4" pipe machine or Ridgid #300 driver) Carbon Steel Sch. 10 1” ~ 6” (Standard) 2" - 3" Sch. 10 & 40 steel RG-R1, E1 Sch. 40 1” ~ 12” (Standard) 4" - 6" Sch. 10 steel (Optional) 1 " Sch. 10 & 40 steel (Optional) 1 1/2" Sch. 10 & 40 steel (to use with Rex 2-4" pipe machine or Ridgid #300 driver) Please Rex Industries Co., Ltd. – www.rexind.co.jp – for updated information on roll sets. For other roll grooving machines, always refer to the installation instructions of the machine and roll set you are going to use before operating.



www.shurt.com

Catalog 2011

Roll Grooving Machines and Tools – Ratings & Capacity Tool Model Pipe No. Material

Pipe Schedule

Pipe size Range

Roll Set

Steel 915 Stainless PVC Copper

Sch. 10 Sch. 40 Sch. 10 Sch. 40 Sch. 40 Sch. 80 K, L, M, DWV

1¼" – 12" 1¼" – 6" 1¼" – 12" 1¼" – 6" 1¼" – 6" 1½" – 3" 2" – 8"

(Standard) 2" – 6" Sch. 10 (2"-3½" Sch. 40) steel, stainless, PVC (Optional) 1¼" – 1½" Sch. 10, 40 steel, stainless, PVC (Optional) 4" – 6" Sch. 40 steel, stainless, PVC (Optional) 8" – 12" Sch. 10 steel, stainless, PVC

Sch. 40 Sch. 80 K, L, M, DWV

1" – 6" 1" – 6" 2" – 6"

(Standard) 1¼" – 6" Sch. 10, 40 steel (Optional) 1" Sch. 10, 40 steel (Optional) 2" – 6" copper tube K, L, M & DWV


Sch. 10 Sch. 40 Sch. 10 Sch. 40 Sch. 10 Sch. 40 K, L, M. DWV

1¼" – 6" 1¼" – 3" 1¼" – 6" 1¼" – 3" 1¼" – 6" 1¼" – 3" 2" – 6"

(Standard) 1¼" – 6" Sch. 10, 40 steel (Optional) 1" Sch. 10, 40 steel


Sch. 10 Sch. 40 Sch. 10 Sch. 40 Sch. 40 Sch. 80 K, L, M. DWV

1" – 12" 1" – 8" 1" – 12" 1" – 2" 1" – 8" 2½" – 6" 2" – 6"

(Standard) 2" – 6" Sch. 10, 40 steel, stainless, PVC (Standard) 8" – 12" Sch. 10 (8" Sch. 40) steel, stainless, PVC (Optional) 1¼" – 1½" Sch. 10, 40 steel, stainless, PVC

Steel PVC Copper

Sch. 10 Sch. 40 Sch. 80 K, L, M. DWV

1" – 12" 1" – 8" 2½" – 6" 2" – 6"

(Standard) 2" – 6" Sch. 10, 40 steel, stainless, PVC (Standard) 8" – 12" Sch. 10 (8" Sch. 40) steel, stainless, PVC (Optional) 1¼" – 1½" Sch. 10, 40 steel, stainless, PVC (Optional) 2" – 6" copper tube K, L, M & DWV

Steel

Sch. 10

1¼" – 6"

(Standard) 1¼" – 6" Sch. 10, 40 steel

Sch. 10 Sch. 40 Standard Wall Sch. 10 Sch. 40 Standard Wall K, L, M. DWV

2" – 24" 2" – 12" 14" – 16" 2" – 24" 2" – 12" 14" – 16" 2" – 8"

(Standard) 2" – 6" Sch. 10, 40 steel, stainless (Standard) 8" – 12" Sch. 10, 40 steel, stainless (Standard) 14" – 16" Standard wall (.375") steel, stainless (Optional) 4"- 6" Sch. 40 steel, stainless (Optional) 18"- 20" Sch. 10 steel, stainless (Optional) 22"- 24" Sch. 10 steel, stainless (Optional) 2"- 8" copper tube K, L, M & DWV

960

Steel Copper

(Optional) 2" – 8" copper tube K, L, M & DWV

918-1



920

Steel Stainless Copper

Please Ridgid Tool Company – www.ridgid.com – for updated information on roll sets. For other roll grooving machines, always refer to the installation instructions of the machine and roll set you are going to use before operating.


www.shurt.com


Catalog 2011

Typical Applications - Flexible Couplings

3. Absorption of distortion

With the use of an assembly as shown below, ground sinking or movement around a tank or reservoir can be effectively absorbed,

- General Systems -

avoiding damage to the tank, reservoir and or the piping system.

1. Absorption of vibration and noise

When a pump operates with frequent starts and stops, the piping system is affected by the noise and vibration of the equipment. The entire system may develop a large sway, referred to as sympathetic vibration, as a result of the frequent cycling. Shurt flexible couplings will help reduce such vibration and noise. The system should always be properly designed with steel angle sway braces to protect the system from large sways.

4. Absorption of inter-floor deflection

Risers of high-rise flexible structure buildings are subjected to lateral sways (inter-floor deflection) when an earthquake occurs. If we assume the inter-floor deflection is 1/150 and the floor height (H) as 4 meters, the estimated inter-floor deflection (α) will be;

Rigid coupling

Flexible coupling

α = H × 1/150

2. Adjustment of misalignment

β

α

When a straight run has need for a slight adjustment of alignment on the jobsite as shown in the diagram, you can accomplish this with the use of two flexible couplings. The following table shows the deflection value (θ) of the Shurt 7705 flexible couplings.

θ

L

H

LL δδ δδ == LL sin sin θθ

Hanger Hanger location location

θθ

α = H x 1/150 = 4000 x 1/150 = 27mm If we use a 200mm (8”) 7707 coupling for each floor, the maximum

Nominal

deflection (β) that each coupling can accommodate will be;

Amount of deflection (δ)

Deflection Distance between couplings (L) mm

β = L x tan θ = 4000 x 0.02915 = 4.56” = 116mm (θ = 1.67°)

Size

Angle(θ)

600

1200

1500

2000

3000

2" / 50

3° 02'

32

64

79

106

159

2 1/2" / 65

2° 30'

26

52

65

87

131

3" / 80

2° 04'

22

43

54

72

108

4" / 100

3° 12'

34

67

84

112

168

5" / 125

2° 36'

27

54

68

91

136

6" / 150

1° 10'

12

24

31

41

61

8" / 200

1° 40'

17

35

44

58

87

As shown in the diagram, each branch connection to the free riser

10" / 250

1° 20'

14

28

35

47

70

12" / 300

1° 08'

12

24

30

40

59

will be subjected to serious shearing forces as pressure thrusts or

The example shows a flexible coupling would be sufficient to absorb this scale of seismic sways.

5. Absorption of misalignment

thermal movement increases. By using two flexible couplings, you can solve this problem.



www.shurt.com

Catalog 2011

As the linear expansion coefficient for steel (α) is 1.2 x 10 , you can -5

use the table above to determine the thermal expansion. Example: Expand

• Pipe size: 100mm (4”) • Max. pipe end separation (E) : 3.2mm

Hanger location

L

• Pipe length (L) : 5.5 m • Temperature difference (∆T) : 40° C (+5° C to +45° C)

6. Curved layout

With Shurt flexible couplings you can design a slowly curved layout for a system along a curved tunnel, winding road or curved building.

μ = α x L x ∆T = 1.2 x 10-5 x 5500 x 40 = 2.64mm The thermal expansion of a 5.5 meter standard length of pipe (μ) is within the allowance (= max. pipe end separation) of a flexible coupling. In other words, if you use a coupling for each pipe length of

L

R = (2 x tan θ/2) (where: R is radius of curvature, L is pipe length, and θ is max. allowed deflection of a coupling)

5.5 meters, the coupling will accommodate the thermal expansion or contraction expected to take place for a 40° C temperature change. When you calculate the necessary number of couplings (N) for an anchored system, you should place a clearance of N x E x ½ as a

R

safety factor. R

Whether it is thermal expansion, contraction, or a combination thereof, the system requires suitable anchor installations with properly space alignment guides and weight devices. Where and when larger thermal movement is anticipated, you should use

Example: When using model 7705 100mm (4”) couplings for the layout as shown in the diagram, the max. allowed deflection (θ) of the coupling is 3.4°, and the pipe length (L) is 5.5 meters, the radius of curvature (R) will be 92.7 meters.

supplementary expansion t(s). For installers who use the imperial units of measure, the following table will be more convenient.

7. Absorption of Thermal Stress

Thermal stress is caused by changes in temperature, resulting in either expansion or contraction. With the use of Shurt flexible couplings you can design your system to accommodate such movement without the need for costly expansion ts. The thermal expansion or contraction (μ) is determined by the length of pipe (L) and temperature difference (∆T). μ = α x L x ∆T

Thermal Expansion (Metric)

Temperature Pipe Length L (meters) Difference

1

5.5*

10

20

30

40

ΔT Thermal Expansion (millimeters) (°C)

1

0.012

0.07

0.12

0.24

0.36

0.48

5

0.06

0.33

0.6

1.2

1.8

2.4

10

0.12

0.66

1.2

2.4

3.6

4.8

20

0.24

1.3

2.4

4.8

7.2

9.6

30

0.36

2

3.6

7.2

11

15

40

0.48

2.6

4.8

9.6

14

20

50

0.6

3.3

6

12

18

24

60

0.72

4

7.2

14

22

29

70

0.84

4.6

8.4

17

25

34

80

0.96

5.3

9.6

19

29

39

Thermal Expansion (Imperial)

Pipe Lenght L (feet)

Temperature

20

40

60

100

(°F) Thermal Expansion between 70° F and indicated temperature (inch)

0

-0.10

-0.20

-0.29

-0.49

25

-0.06

-0.13

-0.19

-0.32

50

-0.03

-0.06

-0.08

-0.14

70

0

0

0

0

100

0.05

0.09

0.14

0.23

125

0.08

0.17

0.25

0.42

150

0.12

0.24

0.37

0.61

175

0.16

0.32

0.48

0.80

200

0.20

0.40

0.59

0.99

225

0.24

0.48

0.73

1.21

* Coefficient of thermal expansion of steel pipe = 6.33 in/in, °F x 10-6

* 5.5 meters is the standard length of commercial carbon steel pipe.


www.shurt.com


Catalog 2011

Anchoring, Hanging and s Shurt grooved couplings are designed to hold axial thrusts 4–5 times their rated working pressure, though the strength against bending movements is less than that of steel pipe. The t may be damaged when a bending movement greater than the allowed deflection occurs. System designers should provide anchors (main

Hangers for straight runs

For straight runs, you can use both flexible and rigid couplings. When rigid couplings are used, the same hanger spacing as other piping methods can be applied. You can refer to the hanger spacing standards of ANSI B31.1 Power Piping Code, B31.9 Building Services

Piping Code, NFPA 13 Sprinkler Systems, or Mechanical Equipment Construction Guide (Japan). See the table below.

and intermediate) and pipe guides with proper spacing to protect the system from unexpected large bending movements.

Suggested Max. Span between s (steel pipe)

These illustrations are examples only, and are not intended to be used for all installations as conditions and requirements vary from job to job. Reliance on general data or information contained herein shall be at the ’s sole risk and without obligation to Shurt.

Hangers shall be designed to five times the weight of waterfilled pipe plus 250 lb (115 kgs) at each point of pipe (NFPA 13 9.1.1.1.). The following illustrations are examples of acceptable hanger types and sizes per NFPA 13.

D dimension

U-Hook sizes Pipe size in

D dimension in / mm

~ 2

2½ ~ 6

⅜ (9.5)

8

½ (12.7)

5/16

(7.9)

Wraparound U-hook

D dimension Rod sizes Pipe size in

D dimension in / mm

Nominal Water Service Gas or Air Service Pipe Size (feet / meters)

(feet / meters)

in/mm

1)

2)

3)

4)

1)

2)

3)

1 / 25

7 / 2.1

9 / 2.7

12 / 3.7

6.6 / 2.0

9 / 2.7

9 / 2.7

9 / 2.7

1¼ / 32

7 / 2.1

11 / 3.4

12 / 3.7

6.6 / 2.0

9 / 2.7

9 / 2.7

11 / 3.4

1½ / 40

7 / 2.1

12 / 3.7

15 / 4.6

6.6 / 2.0

9 / 2.7

9 / 2.7

13 / 4.0

2 / 50

10 / 3.1

13 / 4.0

15 / 4.6

6.6 / 2.0

13 / 4.0

13 / 4.0

15 / 4.6

3 / 80

12 / 3.7

15 / 4.6

15 / 4.6

6.6 / 2.0

15 / 4.6

15 / 4.6

17 / 5.2

4 / 100

14 / 4.3

17 / 5.2

15 / 4.6

6.6 / 2.0

17 / 5.2

17 / 5.2

21 / 6.4

6 / 150

17 / 5.2

20 / 6.1

15 / 4.6

10 / 3.0

21 / 6.4

21 / 6.4

25 / 7.6

8 / 200

19 / 5.8

21 / 6.4

15 / 4.6

10 / 3.0

24 / 7.3

24 / 7.3

28 / 8.5

10 / 250

19 / 5.8

21 / 6.4

10 / 3.0

24 / 7.3

24 / 7.3

31 / 9.5

12 / 300

23 / 7.0

21 / 6.4

10 / 3.0

30 / 9.1

30 / 9.1

33 / 10.1

14 / 350

23 / 7.0

21 / 6.4

30 / 9.1

30 / 9.1

33 / 10.1

16 / 400

27 / 8.2

21 / 6.4

35 / 10.7 35 / 10.7 33 / 10.1

18 / 450

27 / 8.2

21 / 6.4

35 / 10.7 35 / 10.7 33 / 10.1

20 / 500

30 / 9.1

21 / 6.4

39 / 11.9

24 / 600

32 / 9.8

21 / 6.4

42 / 12.8 42 / 12.8 33 / 10.1

39 / 11.9

33 / 10.1

1) ANSI B31.1 Power Piping Code 2) ANSI B31.9 Building Services Piping Code 3) NFPA 13 Sprinkler systems 4) Ministry of Land & Transportation of Japan: Mechanical Equipment Construction Guide

Hanger locations on straight runs where flexible couplings are used When flexible couplings are used on straight runs, location of hangers

~ 4

⅜ (9.5)

shall be designed as close to each coupling as possible, or within a

5 ~ 8

½ (12.7)

10 ~ 12

⅝ (15.9)

distance of less than 1/6 the span. Elevation

Adjustable swivel Ring - rod tight to pipe

max.1/6L L plan

D dimension

Eye rod sizes Pipe size in

~ 4

5 ~ 6

10 ~ 12


max.1/6L D dimension in / mm ⅜ (9.5)

L Correct hanger location

½ (12.7) ¾ (15.1)


www.shurt.com

Wrong hanger location

00

mm

0 .50

ax

m

m 0m

ma

0 x.5

ma

m

0m

0 x.8

mm

00

m

m 0m Ox.v30 ma er 6 00 m

m

0m

.30

x ma

mm

.3 ax

Catalog 2011

Additional hangers or s shall provided 1-1/4"beand above where runs are 1-1/4" and above curved, connected to a branch line or on short risers or drops. Curved pipe runs Short riser (or sh Curved pipe runs

00

x.8

ma

m

Up to 1"

to 1" andUpbranch

Hanger locations on curved pipe runs lines

ma

m

x.5

ma

m 0m

0

.3 ax

m

Ov

er

m

60

0m

Up to 1" 1-1/4" and above

Up to 1"

Short riser (or short drop) Short riser (or short drop)

Curved pipe runs 1-1/4" and above m

0m

.80

m

Curved pipe runs

x ma

m 0m

.30

ax

m

mm 00 x.3O ve r6

m

0m

.30

x ma

mm

00

x.3

ma

ma

Ov

er

00

mm

60

0m

m

Ov

Ov

er

er

60

0m

60

Branch line

0m

m

m

1" 1-1/4" and above Curved pipe runs m

m 00

x.3

ma

m

m 00

Short riser (or short drop) Short riser (or short drop) Ov

er

Ov

er

60

60

0m m m Typical designsO of hangers and sway Ov braces for ve er r6 6 00 00 pipe runs mm mm 0m

Pipe runs shall be adequately suspended by rod hangers or steel

Branch line

Branch line

the movement of the piping. Hangers and their components shall be ferrous. The maximum distance between hangers shall not exceed that specified in the table of previous page.

angles that are directly attached to the building structure to restrict

Short riser (or short drop)

Ov

er

60

m

Inserts Inserts

Branch line

Ov

0m

Branch line

er

60Insert 0m m

Insert

Hanger rod Hanger rod U-bolt

U-bolt

Band hanger Band hanger

A rodfor hanger for a single A rod hanger a single pipe run pipe run Branch line Inserts Inserts

A hanger trapezesuspended hanger suspended from ceiling A trapeze from ceiling

U-bolt Hanger rod Hanger rod

U-bolt

U-bolt

U-bolt Inserts Inserts

A hanger trapezefor hanger for multiple A trapeze multiple pipe runspipe runs A steel angle bracket A steel angle bracket attachedattached to wall to wall


www.shurt.com


m

Catalog 2011

s for risers

In multi-story buildings, risers shall be fixed (or anchored) at the lowest level and at the top of the riser and shall be ed by

Anchors for risers (

riser clamps or U-bolts at each floor level to prevent the risers from swaying. If risers are braced by the penetration floors, the number of riser clamps or U-bolts may be reduced to one at each three stories.

)

weld

For risers, either flexible or rigid couplings

Resilient Isolator

can be used as long as proper anchoring and is provided. Riser clamp

U

Max.

14 F

)

U-bolt

1m

15 F

Sway brace (

)

Max.

1m

Sway braces for risers (

13 F

Sway brace (

)

Anchor ( Heat Insulator )


)

Resilient Isolator

3F

U-bolt 90° Elbow w/Base

Resilient Isolator

2F

1F


)

Sway brace (

)

Sway brace (

Heat Insulator

Flexible Coupling Rigid Coupling Anchor

U-bolt U-bolt

Sway brace

•

•

Anchors should be sufficient to hold the Sway weightbrace of water-filled ( ) pipe and pressure thrusts. Heat Insulator Pipe guides (sway braces) should be such as to brace lateral

movement of the system. Resilient Isolator



)

www.shurt.com

Resilient Isolator

Sway brace

Catalog 2011

Gasket Selection Proper gasket selection is essential for the optimum performance of Shurt grooved couplings, flange adapters and mechanical tees.

6. Dry pipe and freezer services: Shurt recommends the use

1. Compound Grade: In general, Grade "E" EPDM gaskets are

between the pipes or gasket cavity. This will prevent any remaining

of GapSeal® Grade "E" gaskets for dry pipe fire protection systems and freezer applications. The GapSeal® gasket closes off the gap

recommended for cold and hot water services, Grade "T" Nitrile (or

liquid from entering the cavities and freezing when the temperature

NBR) gaskets for oils, Grade "L" Silicone gaskets for hot air and

drops. Rigid couplings are preferred for dry pipe, freezer and

Grade "O" Fluorocarbon gaskets for fuels and harsh chemicals.

vacuum applications. Reducing couplings are not recommended for

Refer to pages 6 & 7 for further details. Failure to select the proper

these applications.

compound may cause a t failure and or property damage. 2. Chemical resistance: The listing of chemical resistance

Do not use the Shurt standard lubricant for dry pipe

shows general service recommendations of Grades "E" (EPDM), "T" (Nitrile), "L" (Silicone), "V" (Neoprene) and "O" (Fluorocarbon,

and freezer systems, instead use a petroleum free silicone based

Viton®) gaskets for various chemicals used at ambient temperatures.

lubricant.

The data and recommendations presented are based on the best information available today. For unusual and or severe services, or

services not listed please Shurt for a recommendation.

3. Service temperatures: In general, rubber compounds can not maintain elasticity and sealing capabilities at temperatures below -40°F (-40°C). Thus, recommended low temperature ranges of

7. ANSI/NSF 61 Standard: ANSI/NSF 61 classified gaskets are good

Shurt gaskets are -30 to -20°F (-34 to -29°C). Resistance

for potable water services. The classification categories are ‘cold’

against elevated temperatures varies depending on the grade of

which is limited to +86°F (+30°C) (or maximum ambient distribution

compound and media (air, water, steam or chemicals). See page 7

temperatures of unheated water) maximum and ‘hot’ which is limited

for details.

to +180°F (+82°C) (or scalding temperatures of hot domestic water).

4. Gasket styles: Shurt grooved couplings utilize several

8. Lubricant: Shurt lubricant is recommended for proper gasket

different gasket styles, standard, GapSeal®, EP (End Protection)

installation to prevent the gasket from being pinched. Apply a thin coat

and FF (Fast Fit). GapSeal® gaskets are compatible with standard

to the gasket exterior, gasket lips and or housing interiors. Shurt

gaskets and they are interchangeable with each other. Other special

lubricant is available in one pound (450 grams) and one quart ( 2

styles are not compatible with standard or GapSeal® gaskets. Always

pounds or 900 grams) containers. Certified to ANSI/NSF 61.

use the correct gasket style for the coupling model you selected.

Standard

GapSeal®

End Protection

FastFit®

5. Vacuum service: Shurt standard gaskets are designed to seal well under vacuum conditions up to 10 inHg (absolute)/254 mmHg (absolute) which may occur when a system is drained. For continuous services greater than 10 inHg (absolute)/254 mmHg (absolute), the use of GapSeal® gaskets or EP (end protection) gaskets in combination with rigid style couplings is recommended. Shurt for specific recommendations.


www.shurt.com


Catalog 2011

Chemical Resistance Number = Max. Recommended Temp. (°F) NR = Not Recommended --- = Incomplete Data Chemical Name

EPDM Nitrile Silicone Neoprene Viton

Chemical Name


Acetaldehyde

200

---

---

NR

NR

Aviation Fuel

NR

150

NR

NR

---

Acetamide

200

150

---

NR

120

Barium Carbonate

200

100

100

160

Acetic Acid, to 10%

180

100

180

NR

NR

Barium Chloride

200

150

100

Chemical Name


Cellulube 220 (Tri-Aryl-Phosphate) 200

---

100

---

200

Cellulube Hydraulic Fluids

200

---

---

---

-----

160

200

China Wood Oil, Tung Oil

NR

150

---

---

---

Acetic Acid, 10 - 50%

140

---

100

NR

NR

Barium Hydroxide

180

150

NR

150

200

Chloralhydrate

NR

NR

NR

70

NR

Acetic Acid, Glacial

100

---

100

NR

NR

Barium Nitrate

200

100

---

160

200

Chloric Acid, to 20%

NR

---

---

140

140 185

Acetic Anhydride

100

100

---

70

NR

Barium Sulfide

140

150

NR

160

200

Chlorine Gas, Dry or Wet

NR

---

---

NR

Acetone

130

---

---

NR

NR

Beer

200

Gr. A

NR

140

200

Chloroacetone

200

NR

NR

---

---

Acetonitrile

NR

100

---

70

NR

Beet Sugar liquors

200

Gr. A

100

160

185

Chlorobenzene

NR

NR

NR

NR

70

Acetophenone

140

---

---

NR

NR

Benzaldehyde

140

NR

NR

NR

NR

Chlorobromomethane

NR

NR

NR

NR

NR

Acetyl Chloride

NR

---

---

NR

185

Benzene

NR

NR

NR

NR

150

Chloroform

NR

NR

NR

NR

70

Acetylene

200

150

100

70

200

Benzene Benzol

200

---

---

---

200

Chlorosulphonic Acid

NR

NR

NR

NR

NR

Acrylic Resin

NR

100

---

100

NR

Benzene Sulfonic Acid

NR

NR

NR

160

185

Chrome Alum

100

100

100

---

---

Acrylonitrile

NR

NR

NR

NR

NR

Benzine

NR

NR

NR

NR

150

Chromic Acid, to 10%

70

---

NR

NR

140

Adipic Acid, Saturated

200

150

---

200

200

Benzoic Acid (Saturated)

NR

---

NR

160

---

---

NR

160

200

Air, oil free

230

140

350

NR

300

Benzol

NR

NR

NR

NR

150

Citric Acid, Saturated

200

100

NR

140

200

Benzyl Alcohol

NR

NR

NR

NR

140

Coconut Oil

NR

Gr. A

NR

100

185

Benzyl Benzoate

140

NR

---

---

---

Cod Liver Oil

NR

Gr. A

100

---

---

Coke Oven Gas

70

150

100

---

185

Air with vapored oil Alkalis Allyl Alcohol

NR

150

---

NR

300

Good

NR

---

---

---

70

---

---

70

100

Black Liquor

180

---

---

70

200

Chromium Potassium Nitrate 140

Allyl Chloride

NR

NR

NR

NR

70

Black Sulfate Liquor

100

150

100

---

---

Copper Acetate, Saturated

100

---

NR

160

140

Aluminum Acetate

200

100

NR

NR

NR

Blast Furnance Gas

NR

150

100

---

---

Copper Carbonate

200

---

---

---

185

Aluminum Ammonium

200

---

---

160

200

Bleach, Industrial (15% Cl2)

70

---

---

---

185

Copper Chloride

200

150

100

160

200

Aluminum Chloride

200

150

NR

160

200

Borax

140

---

---

140

185

Copper Cyanide

200

150

100

160

185

Aluminum Chrome

200

---

---

160

200

Bordeaux Mixture

200

---

---

---

---

Copper Fluoride

200

100

---

140

185

Aluminum Fluoride

200

150

NR

160

200

Boric Acid

140

100

100

140

185

Copper Nitrate

200

150

100

160

200

Aluminum Hydroxide

200

NR

100

100

200

Brine, Acid

200

---

---

160

200

Copper Sulfate

200

150

NR

160

200

Aluminum Nitrate

200

150

73

100

100

Bromobenzene

NR

NR

NR

NR

150

Corn Oil

NR

Gr. A

73

NR

200

Aluminum Phosphate

200

---

100

---

---

Bromotoluene

NR

NR

NR

NR

NR

Corn Syrup

---

Gr. A

100

100

185

Butadiene

NR

NR

NR

140

185

Corrosion Inhibitors (for heating systems)

NR

---

---

---

---

Butane

NR

100

NR

70

185

Cotton Seed Oil

NR

Gr. A

NR

---

185

Aluminum Potassium Sulfate

200

100

100

160

200

Aluminum Salts

200

---

100

---

---

Aluminum Sulfate

200

150

100

140

185

Butanol (see Butyl Alcohol)

200

150

---

140

75

Creosote

NR

100

---

NR

73

Alums

200

150

---

160

NR

Butter

NR

Gr.A

NR

NR

NR

Creosote, Coal Tar

NR

---

---

---

140

Ammmonia

175

---

NR

150

NR

"Butyl "Cellosolve Adipate"

100

100

100

---

NR

Creosote, Wood

NR

---

---

---

140

Ammonia Anhydrous (Pure Ammonia)

NR

NR

NR

NR

NR

Butyl Acetate

140

NR

NR

NR

NR

Cresol

NR

NR

NR

NR

100

Ammonia, Gas

140

100

---

140

NR

Butyl Acetyl Ricinoleate

200

100

---

---

---

Cresylic Acid, to 50%

NR

---

---

---

185

Ammonia, Aqua, 10 - 25%

140

---

---

---

NR

Butyl Alcohol

200

150

73

140

75

Crude Oil

NR

---

NR

---

200

Ammonia Hydroxide

175

---

---

150

NR

Butyl Cellosolve

140

NR

---

---

NR

Crude Oil, Sour

NR

150

---

---

200

Ammonium Acetate

140

---

100

140

73

Butyl Stearate

NR

150

---

NR

200

Cumene

NR

---

---

NR

200

Ammonium Bifluoride

200

150

---

---

200

Butylene

NR

150

---

NR

100

Cupric Fluoride

200

150

---

---

---

Ammonium Carbonate

200

---

NR

140

200

Butylene Glycol

150

150

---

---

---

Cupric Sulfate

200

150

---

160

200

Ammonium Chloride

200

150

NR

160

200

Butyne Diol

NR

NR

NR

NR

NR

Cuprous Chloride

200

---

---

70

200

Ammonium Fluoride, to 10%

200

100

---

100

---

Butyric Acid

140

NR

NR

NR

70

Cyclohexane Alycyclic (Hydrocarbon)

NR

100

NR

NR

185

Ammonium Hydroxide

200

---

NR

150

70

Cium Cyanide

---

---

---

70

---

Cyclohexanol

NR

100

NR

NR

185

Ammonium Metaphosphate 200

---

---

---

200

Calcium Acetate

NR

100

NR

---

---

Cyclohexanone

70

NR

NR

NR

NR

NR

160

100

Calcium Bisulfate

NR

100

NR

---

---

Detergents

200

100

73

160

200

Ammonium Nitrate

200

150

Ammonium Nitrite

200

100

73

---

---

Calcium Bisulfide

NR

100

NR

---

185

Dextrin

NR

150

---

---

200

Ammonium Persulfate

200

NR

100

70

---

Calcium Bisulfite

100

100

73

70

185

Dextrose

140

---

---

160

200

Ammonium Phosphate

200

150

100

140

185

Calcium Carbonate

200

100

100

70

200

Diacetone Alcohol

70

73

NR

NR

NR

Ammonium Sulfamate

---

150

---

---

---

Calcium Chlorate

140

---

100

70

185

Dibutoxy Ethyl Phthalate

70

---

---

NR

200 NR

Ammonium Sulfate

200

150 NR

160

200

Calcium Chloride

200

150

100

160

200

Ammonium Sulfide

200

100

---

---

200

Calcium Hydrochloride

200

---

---

---

---

---

---

---

70

185

Calcium Hydroxide

200

100

NR

70

200

Ammonium Thiocyanate

Dibutyl Phthalate

70

73

NR

NR

Dichloro Difloro Methane

---

150

---

---

---

Dichloroethylene

NR

---

---

NR

185

Amyl Acetate

70

---

NR

NR

NR

Calcium Hypochlorite

70

100

NR

---

185

Dicyclohexylamine

---

73

---

---

---

Amyl Alcohol

200

---

NR

140

185

Calcium Nitrate

200

150

100

100

200

Diesel Oil

NR

150

NR

NR

185

Amyl Borate

NR

100

---

---

---

Calcium Oxide

200

100

NR

160

---

Diethyl Cellosolve

NR

---

---

100

200

Amyl Chloride

NR

NR

NR

NR

200

Calcium Sulfate

200

150

100

160

200

Diethyl Ether

NR

73

NR

---

NR

Amyl Chloronaphthalene

NR

70

NR

---

---

Calcium Sulfide

200

100

100

---

---

Diethyl Sebacate

100

100

100

---

---

Aniline

140

---

NR

NR

140

Caliche Liquors

200

100

100

---

---

Diethylamine

70

100

NR

---

NR

Aniline Hydrochloride

NR

NR

NR

NR

185

Camphor Crystals

200

---

---

NR

200

Diethylene Glycol

200

150

NR

---

---

Aniline Oil

100

---

---

---

---

Cane Sugar Liquors

200

Gr. A

100

160

200

Digester Gas

NR

150

---

---

---

Animal Fats

NR

Gr. A

100

---

---

CarbitolTM

140

100

73

70

70

Dimethylamine

140

150

---

NR

NR

Anthraquinone

NR

NR

NR

NR

200

Carbon Dioxide, Dry

140

150

---

160

200

Dioctyl Phthalate

70

NR

NR

NR

70

Anthraquinone Sulfonic Acid

NR

NR

NR

NR

200

Carbon Dioxide, Wet

140

150

---

160

200

Dioxane

70

NR

---

NR

NR

Antimony Chloride

100

---

---

---

---

Carbon Disulfide

NR

---

---

NR

200

Dipentene (Terpene-Hydrocarbon) NR

73

73

---

---

Antimony Tricholoride

140

---

100

140

185

Carbon Monoxide

200

100

100

70

200

Diproplylene Glycol

---

100

---

---

---

Anyiline Hydrochloride

---

NR

---

---

185

Carbon Tetrachloride

NR

NR

NR

NR

185

Disodium Phosphate

200

---

---

---

---

Argon Gas

200

NR

100

100

200

Carbonic Acid, Fenol

200

100

100

70

200

Divinylbenzene

NR

---

---

---

200

Aroclors

NR

NR

---

---

100

Caster Oil

140

Gr. A

NR

100

---

Dowtherm A

NR

NR

NR

---

140

Arsenic Acid, to 75%

185

150

100

NR

200

Caustic Potash

140

---

---

160

NR

Dowtherm E

NR

NR

NR

---

140

Arylsulfonic Acid

140

NR

NR

NR

185

Cellosolve

140

NR

NR

---

NR

Dowtherm SR-1

100

100

---

---

---

ASTM #1, 2 & 3 Oil

NR

150

NR

NR

100

Cellulose Acetate

140

NR

NR

NR

NR

Epsom Salt

200

100

---

---

---



www.shurt.com

Catalog 2011 Chemical Name


Chemical Name


Chemical Name


Ethanolamine

140

NR

---

---

---

Hydraulic Oil

NR

---

NR

70

200

Methylene Iodine

200

---

---

---

---

Ethers

NR

NR

NR

NR

NR

Hydrobromic Acid, to 50%

140

100

---

70

185

MIL-05606

NR

NR

---

---

100 100

"Ethyl "Cellusolve"

100

NR

NR

---

---

Hydrochloric Acid, to 37%

75

NR

NR

---

158

MIL-08515

NR

NR

---

---

Ethyl Acetoacetate

100

NR

73

---

NR

Hydrocyanic Acid, to 10%

200

NR

---

---

185

MIL-L7808

NR

NR

NR

---

100

Ethyl Acrylate

70

NR

100

NR

NR

Hydrofluoric Acid, to 30%

NR

NR

NR

70

150

Milk

200

Gr. A

100

160

200

Ethyl Alcohol (Ethanol)

200

150

NR

---

---

Hydrofluosilicic Acid, to 50%

140

150

---

---

200

Mineral Oils

NR

150

NR

70

200

Ethyl Cellulose

NR

73

NR

---

---

Hydrogen Gas

200

73

NR

160

100

Molasses

100

100

100

150

185

Ethyl Chloride

70

100

NR

70

140

Hydrogen Peroxide, to 30%

140

NR

100

NR

200

Monochloroacetic Acid, to 50%

NR

---

---

NR

70

Ethyl Ether

NR

70

---

NR

NR

Hydrogen Phosphide

NR

NR

NR

NR

NR

Monoethanolamine

70

NR

NR

NR

185

Ethyl Oxalate

100

NR

NR

---

---

Hydrogen Sulfide.

100

NR

NR

NR

140

Motor Oil

NR

150

NR

---

200

Ethyl Silicate

100

100

---

---

---

Hydroquinone

NR

150

100

NR

185

Naphta

NR

160

NR

NR

160

Ethylene

NR

100

NR

NR

140

Hydroxylamine Sulfate

70

---

---

70

---

Naphtalene

NR

NR

NR

NR

170

Ethylene Chlorohydrin

70

NR

NR

70

NR

Hypochlorous Acid

70

---

---

---

70

Naphtenic Acid

NR

100

NR

---

---

Ethylene Diamine

70

100

---

100

---

Iodine Solution, to 10%

150

---

---

---

200

Natural Gas

NR

150

100

140

185 NR

Ethylene Dichloride (Dichloroethane)

NR

---

---

NR

120

Isobutyl Alcohol

180

100

NR

---

---

Nickel Acetate

70

NR

NR

100

Ethylene Glycol

200

150

73

160

200

Isododecane

NR

100

NR

100

---

Nickel Ammonium Sulfate

70

---

---

100

---

Ethylene Oxide

NR

NR

NR

NR

NR

Isooctane

NR

100

NR

70

185

Nickel Chloride

200

150

100

160

200

Fatty Acid

NR

Gr. A

NR

140

185

Isooctyle Alcohol

140

---

---

---

---

Nickel Nitrate

180

100

100

160

200

Ferric Chloride, to 35%

200

150

NR

160

200

Isopropyl Acetate

140

NR

NR

---

---

Nickel Sulfate

200

150

---

160

200

Ferric Hydroxide

180

---

---

100

180

Isopropyl Alcohol

140

100

NR

70

160

Nicotine

NR

---

---

70

---

Ferric Nitrate

200

100

100

160

200

Isopropyl Ether

NR

100

NR

NR

NR

Nicotine Acid

70

---

---

70

---

Ferric Sulfate

200

100

NR

140

185

Jet Fuel, JP-4

NR

150

NR

NR

200

Nitric Acid, to 10%

75

---

100

NR

185

Ferrous Chloride

200

100

NR

---

200

Jet Fuel, JP-5

NR

150

NR

NR

200

Nitric Acid, 10 - 50%

NR

---

100

NR

160

Ferrous Hydroxide

180

---

---

---

180

Kerosene

NR

150

NR

70

200

Nitric Acid, Red Fuming

NR

---

---

NR

100 70

Ferrous Nitrate

180

---

---

160

200

Ketones

NR

NR

NR

NR

NR

Nitrobenzene

70

NR

NR

---

Ferrous Sulfate

200

150

100

160

200

Lactic Acid

70

Gr. A

---

140

70

Nitrocellulose

---

100

100

100

---

Fire Fighting Form (AFFF)

180

---

---

---

---

Lard Oil

NR

Gr. A

---

70

185

Nitroethane

100

NR

NR

---

-----

Fish Oils (Solubles)

NR

Gr. A

73

---

70

Latex (1% Styrene & Butadiene)

NR

NR

NR

NR

140

Nitrogen

180

150

---

---

Fluboric Acid

140

---

NR

160

140

Lauric Acid

NR

100

NR

NR

100

Nitromethane

70

NR

NR

---

---

Fluorine Gas, Wet

NR

NR

NR

NR

NR

Lauryl Chloride

140

NR

NR

NR

200

Nitrous Acid, to 10%

NR

---

100

---

100

Fluorosilicic Acid, to 30%

140

100

---

100

200

Lavender Oil

NR

100

NR

---

---

Nitrous Oxide

NR

100

100

NR

70

Fly Ash

180

---

---

---

---

Lead Acetate

200

150

NR

160

NR

Octyl Alcohol

NR

100

100

100

---

FM200

200

---

200

200

---

Lead Chloride

NR

---

---

70

140

Ogisogiric Acid, to 75%

NR

NR

NR

NR

150

Oleic Acid

70

100

NR

70

185

Oleum

NR

NR

100

NR

NR

Olive Oil

---

Gr. A

NR

140

150

Foam

180

---

---

---

---

Lead Nitrate

175

100

100

140

200

Fog Oil

NR

100

---

---

---

Lead Sulfamate

140

73

100

---

---

Formaldehyde

140

100

NR

140

NR

Lead Sulfate

200

150

---

140

200

Formanide

NR

100

---

---

---

Lemon Oil

---

Gr. A

NR

100

200

Oronite 8200 Silicate Ester Fluid

NR

NR

---

---

150

Formic Acid, to 25%

200

100

---

140

NR

Ligroine

---

100

NR

70

100

Orthodichlorobenzene

NR

NR

NR

---

150

Freon F-11

NR

130

NR

NR

70

Lime and H_O

180

150

---

---

---

OS-45 Silicate Ester Fluid

NR

NR

---

---

150

Freon F-113

NR

130

NR

130

130

Lime Sulfur

200

NR

100

100

185

OS-45-1

NR

NR

NR

---

150

Freon F-114

NR

130

NR

70

NR

Linoleic Acid

70

73

NR

---

140

Oxalic Acid

150

---

---

100

100

Freon F-12

NR

130

NR

130

NR

Linseed Oil

70

Gr. A

NR

70

200

Oxygen

200

NR

NR

140

185

Freon 123

NR

NR

NR

NR

NR

Lithium Bromide (Brine)

---

100

---

---

200

Ozone (100 ppm)

200

100

100

NR

185

Freon 134a

NR

NR

NR

NR

NR

Lithium Chloride

100

100

---

---

140

Palm Oil

NR

Gr. A

---

---

70

Freon F-21

NR

NR

NR

NR

NR

Lubricating Oil, ASTM#1,#2,#3

NR

150

---

180

150

Palmitic Acid

70

150

---

NR

185

Freon F-22

NR

NR

---

130

NR

Magnesium Ammonium Sulfate

NR

NR

NR

70

NR

Paraffin

NR

100

NR

140

200

Fructose

175

150

---

160

200

Magnesium Carbonate

170

100

100

140

200

Peanut Oil

NR

Gr. A

100

---

150 200

Fruit Juice, Pulp

---

Gr. A

---

---

200

Magnesium Chloride

170

150

100

160

170

Pentachlorophenol

NR

---

---

NR

Fuel Oil

NR

150

NR

---

100

Magnesium Citrate

175

---

---

---

200

Pentane

---

100

---

---

---

Fumaric Acid

100

100

---

---

100

Magnesium Fluoride

140

---

---

---

200

Perchloric Acid, to 10%

70

NR

NR

70

70

Furan

NR

NR

NR

NR

NR

Magnesium Hydroxide

200

150

100

---

200

Perchloric Acid, to 70%

70

NR

NR

NR

185

Furfural

140

---

---

70

NR

Magnesium Nitrate

200

100

100

160

---

Perchloroethylene

---

---

---

---

150

Furfuryl Alcohol

140

NR

---

---

---

Magnesium Oxide

140

73

---

160

---

Petroleum Ether (see Benzene)

NR

NR

NR

NR

150

Gallic Acid

70

100

NR

70

185

Magnesium Sulfate

175

150

100

160

200

Petroleum Oils

NR

150

NR

---

200

Gasoline, Leaded

NR

---

---

70

100

Maleic Acid, Saturated

70

100

---

NR

200

Phenol (Carbolic Acid)

70

NR

NR

NR

200

Gasoline, Refined

NR

100

---

---

---

Malic Acid

---

100

100

---

---

Phenylhydrazine

NR

---

---

---

NR

Gasoline, Sour

NR

---

---

---

100

Manganese Sulfate

175

---

---

160

200

Phenylhydrazine Hydrochloride

70

---

---

---

---

Gasoline, Unleaded

NR

100

---

---

100

Mercuric Chloride

200

150

100

140

185

Phosohoric Acid, to 10%

140

100

NR

140

200

Gelatin

200

Gr. A

73

160

200

Mercuric Cyanide

70

100

100

70

70

Phosohoric Acid, 10 - 50%

70

100

NR

70

200

Glucose

200

Gr. A

100

160

200

Mercurous Nitrate

70

100

---

NR

70

Phosphorous Pentoxide

200

---

---

---

200 185

Glue

150

150

73

---

---

Mercury

200

150

100

140

185

Photographic Solutions

100

150

100

---

Glycerine

200

150

100

160

200

Methane

NR

70

NR

70

185

Phthalic Anhydride

100

NR

NR

---

---

Glycerol

150

100

---

---

---

Methyl Acetate

140

NR

NR

140

---

Picric Acid

140

100

NR

70

140

Glycol

180

100

73

---

---

Methyl Alcohol, Methanol

140

140

NR

140

NR

Pine Oil

---

NR

NR

NR

70

Glycolic Acid

NR

73

73

70

NR

Methyl Amine

70

---

---

70

100

Plating Solutions, Brass

70

---

---

100

70

Grape Sugar, Juice

200

Gr. A

---

160

185

Methyl Butyle Ketone

140

---

---

---

---

Plating Solutions, Cium

70

---

---

100

70

Grease

NR

150

NR

---

185

Methyl Bromide

NR

100

NR

NR

185

Plating Solutions, Chrome

---

---

---

NR

140

Green Sulfate Liquor

180

150

100

70

---

Methyl Cellosolve

70

NR

NR

70

NR

Plating Solutions, Copper

70

---

---

100

70

Halon 1301

180

NR

---

---

140

Methyl Chloride

NR

NR

NR

NR

70

Plating Solutions, Gold

70

---

---

125

70

Heptane

NR

100

---

70

185

Methyl Cyclopentane

NR

NR

NR

70

70

Plating Solutions, Lead

70

---

---

70

70

Hexaldehyde

180

NR

100

---

---

Methyl Ethyl Ketone

70

NR

NR

NR

NR

Plating Solutions, Nickel

125

---

---

70

70

Hexane

NR

70

NR

70

70

Methyl Formate

100

NR

100

70

NR

Plating Solutions, Silver

70

---

---

100

70

Hexanol

NR

---

---

70

160

Methyl Isobutyl Ketone

NR

NR

NR

NR

NR

Plating Solutions, Tin

100

---

---

100

140

Plating Solutions, Zinc

70

---

---

100

70

Hexanol Tertiary

NR

100

---

---

---

Hexyl Alcohol

NR

100

NR

100

185

Hexylene Glycol

NR

100

---

---

---

Methylene Chloride

NR

NR

---

NR

73

Methylene Chlorobromide

NR

NR

NR

NR

NR

Methylene Dichloride

NR

---

---

---

100


www.shurt.com


Catalog 2011 Chemical Name


Polyvinyl Acetate, Solid in Liquid State is 50% solution of

Chemical Name


Chemical Name


Sodium Ferricyanide

140

100

---

---

140

Turbo Oil #15 Diester Lubricant

NR

NR

---

---

150

Sodium Ferrocyanide

140

100

---

---

140

Turpentine

NR

100

---

NR

150

Sodium Fluoride

140

100

NR

70

140

Urea

200

150

100

140

185 70

180

---

---

---

---

---

160

200

Sodium Hydroxide, to 15%

180

NR

NR

160

NR

Urine

200

100

---

140

Potassium Acetate

170

150

NR

---

---

Sodium Hypochlorite, to 20%

70

100

---

NR

185

Vaseline

NR

---

---

140

70

Potassium Alum

200

100

---

160

200

Sodium Metaphosphate

70

100

---

---

70

Vegetable Oils

NR

Gr. A

100

70

200

Methanol or 60% solution of (H2O) Potash

Potassium Aluminum Sulfate

200

---

---

160

200

Sodium Nitrate

200

NR

NR

140

200

Vinegar

180

Gr. A

100

70

NR

Potassium Bicarbonate

170

150

---

160

200

Sodium Nitrile

170

150

---

140

200

Vinyl Acetate

70

NR

NR

NR

NR

Potassium Bisulfate

170

---

---

140

200

Sodium Perborate

70

70

NR

70

70

Vinyl Chloride

NR

NR

NR

NR

70

Potassium Borate

200

---

---

---

200

Sodium Peroxide

140

NR

NR

70

185

Vi-Pex

---

100

---

---

---

Potassium Bromate

---

---

---

140

200

Sodium Phosphate, Acid

170

---

---

140

200

Water

230

150

100

160

200

Potassium Bromide

170

150

---

160

200

Sodium Phosphate, Alkaline

170

---

---

140

200

Water, Acid Mine

200

150

---

160

---

Potassium Carbonate

170

150

100

160

200

Sodium Phosphate, Neutral

170

---

---

140

200

Water, Bromine

NR

NR

NR

NR

185

Potassium Chlorate

140

100

100

100

140

Sodium Silicate

200

150

---

140

200

Water, Chlorinated, to 3500ppm

100

---

---

NR

185

Potassium Chloride

200

150

100

160

200

Sodium Sulfate

140

100

100

140

200

Water, Chlorinated, above 3500ppm

NR

---

---

NR

185

Potassium Chromate

170

150

---

70

200

Sodium Sulfide

140

100

100

140

200

Water, Deionized

200

150

100

160

---

Potassium Cyanide

140

100

100

160

185

Sodium Sulfite

140

100

100

140

200

Water, Demineralized

200

150

---

160

200

200

150

100

160

---

---

160

---

Potassium Dichromate

170

100

100

---

200

"Sodium Thiosulfate "hypo"

200

150

100

160

200

Water, Distilled

Potassium Ferrocyanide

140

NR

---

150

140

Sohovis 47

---

100

---

---

---

Water, Potable

Potassium Fluoride

140

---

---

---

---

Sohovis 78

---

100

---

---

---

Water, Salt

200

150

---

160

---

Potassium Hydroxide

140

150

NR

160

NR

Solvasol #1,2 & 3

---

100

---

---

---

Water, Sewage

200

150

---

---

---

Gr. E-pw Gr. A

Potassium Iodide

140

---

100

160

180

Solvasol #73

---

70

---

---

---

Water, Seawater

200

150

---

160

---

Potassium Nitrate

200

150

100

140

200

Solvasol #74

NR

NR

NR

NR

NR

Water, Swimming Pool

200

150

---

---

---

---

---

---

70

---

Soybean Oil

NR

Gr. A

73

---

200

Water, waste

200

150

---

---

---

140

150

---

---

150

Spindle Oil

NR

100

---

Whiskey

200

Gr. A

100

140

140

Potassium Perborate Potassium Perchlorate

Potassium Permanganate, to 10% 200

150

---

100

140

Stannic Chloride

100

100

100

NR

200

White Liquor

170

Gr. A

---

140

---

Potassium Permanganate, to 25% 140

100

---

100

140

Stannous Chloride

70

NR

NR

160

200

Wines

170

Gr. A

100

140

140

Potassium Persulfate

200

150

---

140

200

Starch

170

100

---

160

200

Wood Oil

NR

100

NR

---

---

Potassium Silicate

200

150

---

140

---

Steam

NR

NR

NR

NR

NR

Xylene

NR

NR

NR

NR

150

Potassium Sulfate

200

150

NR

140

200

Stearic Acid

NR

100

NR

70

100

Zinc Acetate

180

100

NR

160

70

Prestone

---

100

---

---

---

Stoddard Solvent

NR

100

NR

NR

185

Zinc Chloride

180

100

100

160

200

Propane Gas

NR

100

NR

70

70

Styrene

NR

NR

NR

NR

100

Zinc Nitrate

180

---

---

---

200

Propanol

---

---

---

---

---

Sucrose Solutions

---

Gr. A

---

---

---

Zinc Sulfate

180

100

100

140

200

140

---

---

NR

140

Sulfamic Acid

NR

---

---

70

NR

Propargyl Alcohol Propyl Acetate

NR

NR

NR

140

---

Sulfite Liquor

140

---

---

70

140

Propyl Alcohol

140

150

100

140

---

Sulfer Dioxide, Dry

140

100

---

---

---

Propylene Dichloride

NR

---

70

NR

70

Sulfonic Acid

150

---

---

---

---

Propylene Glycol

200

100

100

100

140

Sulfur

140

NR

NR

70

200

Propylene Oxide

70

NR

NR

NR

NR

Sulfur Chloride

NR

NR

NR

NR

70

Pydraul F-9 and 150

NR

NR

NR

NR

NR

Sulfur Dioxide, Dry

70

NR

---

NR

100

Pyranol 1467

NR

100

100

---

---

Sulfur Dioxide, Wet

140

NR

---

---

140

Pyranol 1476

NR

100

100

---

---

Sulfur Trioxide

70

NR

NR

NR

140

"Pyroguard "C"

---

100

100

---

---

Sulfuric Acid, 10 - 30%

150

NR

73

100

200

"Pyroguard "D"

---

100

100

---

---

Sulfuric Acid, Fuming

NR

NR

NR

NR

100

Pyroguard 55

180

---

NR

---

---

Sulfuric Acid, Oleum

NR

NR

NR

NR

100

Pyrrole

100

NR

73

---

---

Sulfurous Acid

75

NR

NR

NR

100

Rapeseed Oil

NR

Gr. A

NR

---

---

Tall Oil

NR

70

---

70

70

Ref. Fuel (ISO Octane, 30 Toluene)

---

150

---

---

---

Tannic Acid, all conc.

70

100

73

100

100

Rosin Oil

NR

100

---

100

---

Tannic Acid, Liquors

100

---

---

70

200

Salicylic Acid

200

100

100

NR

185

Secondary Butyl Alcohol

Tanning Liquors( 50g. alum.

---

100

---

---

---

Solution, 50g. dichromate solution)

NR

150

---

70

200

Sewage

200

150

100

---

---

Tar

NR

100

100

70

185

Silicic Acid

140

---

---

140

200

Terpienol

NR

NR

---

70

185

Silicone Oil

140

100

NR

70

185

Tertiary Butyl Alcohol

140

100

---

70

150

Silver Cyanide

140

---

---

70

140

Tetrabutyl Tinanate

140

100

---

---

185

Silver Nitrate

200

NR

100

160

200

Tetrachloroethylene

NR

---

---

---

150

Silver Sulfate

170

---

---

---

200

Tetrahydrofuran

NR

NR

NR

NR

NR

Skydrol 200

200

---

200

---

---

Tetralin

NR

NR

NR

NR

NR

Skydrol 500 Phosphate Ester 170

---

---

---

---

Tetraric Acid

140

---

---

---

---

200

150

100

140

200

Thionyl Chloride

NR

NR

100

NR

100

Soda Ash, Sodium Carbonate 180

100

---

---

---

Thiopene

NR

NR

NR

NR

NR

Sodium Acetate

170

NR

NR

---

NR

Thread Cutting Oil

NR

NR

NR

NR

70

Sodium Alum

170

150

---

140

200

Titanium Tetracholoride

NR

NR

NR

---

185

Sodium Aluminate

200

100

---

140

200

Toluene, to 30%

NR

100

---

---

70

Sodium Benzoate

200

150

100

---

200

Tomato Juice

200

Gr. A

---

70

200

Sodium Bicarbonate

200

150

NR

160

200

Transformer Oil

140

150

---

NR

140

Sodium Bichromate

140

---

---

70

200

Transmission Fluid, Type A

NR

150

---

---

140

Sodium Bisulfate

200

150

NR

140

200

Triacetin

NR

100

---

---

---

Sodium Bisulfite (Black Liquor)

200

150

NR

140

200

Trichloroethane

NR

NR

NR

---

200

Sodium Borate

140

100

NR

100

140

Trichloroethylene

NR

---

---

NR

200

Sodium Bromide

200

150

---

70

200

Tricresyl Phosphate

NR

NR

NR

---

---

Sodium Carbonate

140

150

100

140

200

Triethanolamine

70

70

NR

70

NR

Sodium Chlorate

140

NR

100

140

100

Triethylamine

---

100

NR

70

200

Sodium Chloride

140

100

NR

160

200

Trimethylpropane

180

---

---

160

---

Sodium Cyanide

140

100

NR

140

140

Trisodium Phosphate

70

---

100

70

185

Sodium Dichromate

140

100

---

NR

200

Tung Oil

NR

100

---

---

---

Soap Solutions



www.shurt.com

Catalog 2011

Fire Protection Services The Shurt fire protection series numbers over 600 individual components, including grooved couplings, fittings, flanges, mechanical tees, valves, welding outlets, threaded fittings and more. Applicable products are listed and or approved by various domestic and international approval bodies including UL, FM, VdS, LPCB and others. HYDROSTATIC TESTS A p p r o v e d

products are rated in cold water pressure

(CWP) tested with a 3 to 5 times test pressure depending on the approval body and pipe size. The minimum working

See the table below for the bending

and larger, the angular movement shall be

moments per UL and FM on Sch. 40 pipe.

permitted to be less than 1 degree but not

This bending moment is twice that required

less than 0.5 degrees.” (NFPA 13 - 2007

by ASTM F1476 (refer to page 13).

3.5.4)

Required Bending Moment by UL & FM

the use of flexible couplings to protect the

For sprinkler systems, NFPA 13 specifies

Nom. Size (inches) 1½ 2 2½ 3 4 5 6 8 10 12 14 16

UL FM Moment Moment Moment Moment N-m Lb-Ft N-m Lb-Ft 1098 810 1100 810 1559 1150 1560 1150 2400 1770 2400 1770 3289 2426 3290 2425 4942 3645 4975 3670 7102 5238 7105 5240 9606 7085 9615 7090 15326 11304 15335 11310 22757 16785 22790 16805 31116 22950 31145 22970 37217 27450 48597 35843

system against damage from earthquakes and lists some specific examples of how and where they should be used. Designers and installers should design their fire protection systems in compliance with this standard. See Typical Applications – Flexible

Couplings on Page 154.

pressure (CWP) shall be 175 psi (12.3 Bar) in accordance with NFPA 13. Approval testing of a coupling is conducted on all

Pipe

Force, F40 Test t

Capped End

different pipe schedules as enrolled and approved working pressures (CWP) are assigned to each individual combination

Capped End

of the coupling and test pipe. Refer to the

Approved Pressure Ratings by UL and FM.

Up to 6” / 150 8” – 12” / 200 -300 14” and above

requirements including gasket performance

UL

FM

VdS

LPCB

X5 X4 X3

X4 X4 X4

X4 X4 NA

X4 X4 NA

Shurt for other approvals.

Pipe

In addition to the hydrostatic and bending moment tests, couplings must meet other

Hydrostatic Test Pressures (= multiple of CWP) Nom. Size

Spacing, LS

tests.

FLEXIBLE COUPLING NFPA 13 defines

a flexible coupling as “a listed coupling or fitting that allows axial displacement,

Test t

Capped End

rotation, and at least 1 degree of angular movement of the pipe without inducing harm on the pipe. For pipe diameters of 8 in.

Minimum Overall Length 2 ft (610 mm)

Capped End

Force, F40

Capped

Test t BENDING TESTS End The PipeMOMENT

required bending moment per UL and FM

is calculated based on twice the weight of water Cappedfilled pipe over twice the maximum Spacing, LS

End

distance between pipe s as specified in NFPA 13. Lhs = 15 ft

Lhs = 15 ft

Water Filled Schedule 40 Steel Sprinkler Pipe


www.shurt.com


Catalog 2011

Approved Pressure Ratings by UL & FM 6. Approved grooved couplings may be used in underground service

1. Approved grooved couplings and fittings are good for use in both

subject to the installation restrictions placed upon the pipe and to

wet and dry sprinkler systems.

the coupling manufacturer’s recommendations and requirements.

2. Typical applications of flexible couplings (models 7705, 7706

7. Approved grooved couplings have been evaluated for a maximum

& 7707) are in sprinkler risers, in feed mains ing through

ambient temperature of 225°F (107°C), suitable for normal

walls from one building area to another, in locations subject to

warehouse protection.

earthquakes, in the discharge line from aboveground pump suction

8. Threaded size of sprinkler piping is limited to 1 inch (25mm)

tanks, in new connections to existing feed mains and in air or

nominal.

water fire service lines subject to excessive vibration or difficult

9. Threaded connections can be made to approved threadable

alignment.

thinwall pipe or to Schedule 40 pipe.

3. Approved grooved couplings are limited to use with rolled or cutgroove ended pipe, valves and fittings at a minimum rated working

Source: FM Approval Guide

pressure of 175 psi (1205 kPa) and are suitable for aboveground

• For pressure ratings for special pipes, DIN and JIS pipe sizes, and large diameter sizes 14” – 24”, Shurt for details. • Models K-9 and 7771 rigid couplings are also available. For pressure ratings, Shurt for details.

service. 4. Grooves should be processed according to ANSI/AWWA C606 (latest edition) Grooved and Shouldered ts. 5. Installation must be made according to the manufacturer’s instructions and requirements.

Couplings and Flange Adapters Sch. 40 & STD Wall Pipe

Size in ¾ 1 1¼ 1½ 2 2½ 3 4 5 6 8 10 12

Wall in 0.113 0.133 0.140 0.145 0.154 0.203 0.216 0.237 0.258 0.280 0.322 0.375 0.375

UL - 300 300 300 300 300 300 300 300 300 300 175^ 175*

Unit: psi

7705 FM - 300 300 300 300 300 300 300 300 300 300 250 250

UL 500 500 500 500 500 500 500 500 500 500 500 300 300

7707 FM 500 500 500 500 500 500 500 500 500 500 500 500 300

UL - - 350 350 350 350 350 350 350 350 350 - -

Z05 FM - - 350 350 350 350 350 350 350 350 350 - -

UL - - 350 350 350 350 300 350 350 350 - 350 - 350 NA NA

Z05 FM - - 350 350 350 350 - 350 350 350 - 350 - 350 NA NA

UL - 500 500 500 500 500 500 500 400 400 400 350 350

Z07 FM - 500 500 500 500 500 500 500 400 400 400 350 350

UL - 500 500 500 500 500 - 500 500 400 - 400 - 400 350 350

Z07 FM - 500 500 500 500 500 - 500 500 400 - 400 - 400 350 350

UL - - - - 175 175 175 175 175 175 175 175 175*

7041 FM - - - - 175 175 175 175 175 175 175 175 175

UL - - - - 300 300 300 300 300 300 300 300 300

7043 7706 FM Size (in) UL FM - 2 x 1½ 300 300 - 2½ x 2 300 300 - 3 x 2 300 300 - 3 x 2½ 300 300 300 4 x 2 300 300 300 4 x 2½ 300 300 300 4 x 3 300 300 300 6 x 3 300 300 300 6 x 4 300 300 300 8 x 6 300 300 300 300 300

UL - - - - 175 175 175 175 175 175 175 175 175 175 175 175*

7041 FM - - - - 175 175 - 175 175 175 - 175 - 175 175 175

7043 UL FM Size (in) - - 2 x 1½ - - 2½ x 2 - - 76.1 x 2 - - 3 x 2 300 300 3 x 2½ 300 300 3 x 76.1 - - 4 x 2 300 300 4 x 2½ 300 300 4 x 76.1 300 300 4 x 3 - - 6 x 3 300 300 165.1 x 3 - - 6 x 4 300 300 165.1 x 4 300 300 8 x 6 300 300 8 x 165.1

^ 0.188" wall, * 0.330 wall Unit: psi

Size in 8

Wall in 0.322

7705H

UL 450

FM 450

Sch. 10 & BS1387 Medium Pipe Size in ¾ 1 1¼ 1½ 2 2½ 76.1 3 4 5 139.7 6 165.1 8 10 12

Wall in 0.083 0.109 0.109 1.109 0.110 0.120 0.142 0.120 0.120 0.134 0.197 0.134 0.197 0.188 0.188 0.250

7705 UL FM - - 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 175 175 175* 175

Wall in 0.188

7705H

Unit: psi

7707 UL FM 500 500 500 500 500 500 500 500 450 450 450 450 500 500 450 450 450 450 450 450 500 500 450 450 500 500 450 450 300 450 300 300

* 0.330 wall Unit: psi

Size in 8


UL 450

FM 450


www.shurt.com

7706 UL FM 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300

Catalog 2011

Approved Pressure Ratings by UL and FM Outlet Coupling and Mechanical Tees

Model C-7 Outlet Coupling, Threaded C-7 Outlet Coupling, Grooved M21 Mechanical Tee, Threaded (NPT or BSPT) M22 Mechanical Tee, Grooved 7721 Threade (NPT or BSPT) 7722 Grooved 723 Threaded (NPT or BSPT)

Sizes (in) (run x branch) 1½ x ½, ¾ & 1 2 x ½, ¾ & 1 2½ x ½, ¾ & 1 3 x ¾ & 1 4 x ¾ & 1 6 x 1 & 1½ 2 x 1 2½ x 1¼ & 1½ 3 x 1 & 1½ 4 x 1½ & 2 6 x 1½ & 2 2 x ½, ¾, 1, 1¼ & 1½ 2½ x ½, ¾, 1, 1¼ & 1½ 76.1 x 15, 20, 32 & 40 3 x ½, ¾, 1, 1¼, 1½ & 2 4 x ½, ¾, 1, 1¼, 1½, 2 & 2½ 100 x 65 (76.1) 4 x 3 5 x 2 & 2½ 125 (139.7) x 50, 65 (76.1) & 80 6 x 1¼, 1½, 2 & 2½ 6 x 3 & 4 150 (165.1) x 32, 40, 50 & 65 (76.1) 150 (165.1) x 80 & 100 2 x 1, 1¼ & 1½ 2½ x 1, 1¼ & 1½ 76.1 x 25, 32 & 40 3 x 1, 1¼, 1½ & 2 4 x 1, 1¼, 1½, 2 & 2½ 100 x 65 (76.1) 5 x 2 & 2½ 4 x 3 125 (139.7) x 65 (76.1) 6 x 1¼, 1½, 2 & 2½ 6 x 3 & 4 150 (165.1) x 32, 40, 50 & 65 (76.1) 150 (165.1) x 80 & 100 4 x 3 8 x 2, 2½, 3 & 4 200 x 65 (76.1) 4 x 3 8 x 2, 2½, 3 & 4 200 x 65 (76.1) 1¼ x ½ x ¾ & 1 1½ x ½ x ¾ & 2 2 x ½ x ¾ & 3 2½ x ½ x ¾ & 4

Grooved-end Fittings

Unit: psi

Sch. 40/STD UL FM 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 175 175 300 300 300 300 300 300 175 175 300 300 175 175 300 300 300 300 300 300 300 300 300 300 300 300 300 300 175 175 300 300 300 300 175 175 300 300 175 175 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300

Sch. 10 UL FM 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 175 175 300 300 300 300 300 300 175 175 300 300 175 175 300 300 300 300 300 300 300 300 300 300 300 300 300 300 175 175 300 300 300 300 175 175 300 300 175 175 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300

Unit: psi

Model Size Range 901 S/ R 90 Elbow 2" thru 8" 903 S/R Tee 2" thru 8" 1" thru 8" 7110 90 Elbow 10", 12" 1" thru 8" 7111 45 Elbow 10", 12" 7110DR Drain Elbow 2" thru 6" 7110LR 1.5D Elbow 2" thru 8" 1½" 7112 22-1/2 Elbow 2" thru 8" 7113 11-1/4 Elbow 2" thru 8" 1¼" thru 8" 7120 Tee 10", 12" 7121 Reducing Tee 2"x1½" thru 8"x6" 7125 Bullhead Tee 2"x2½" thru 6"x8" 7127 Standpipe Tee 4"x2½", 6x2½" 7130 Lateral 2" thru 8" 7135 Cross 2" thru 6" 7150 Conc. Reducer 2"x1½" thru 14"x12" 7150F Socket Adapter 1½"x1" thru 6"x4" 7150M Red. Nipple 1½"x1" thru 6"x4" 7160T Transition Fitting 2"x1" thru 6"x2" 7151 Ecc. Reducer 2½"x2" thru 8"x6" 7160 End Cap 1¼" thru 12" 10" thru 12" 7160H End Cap 14" thru 18" 20" thru 24" 7170 Flange Adapter 2-1/2" thru 6" 7180 Flange Adapter 2" thru 8" 7181 Red. Flange 3"x2" thru 6"x4" 55 Nipple Adapter 1½" thru 2" 899 End All 1¼"x½" thru 2½"x1" 850 Sprinkler Hub 2"x2"x1" thru 2½"x2½"x1" 851 Sprinkler Hub 2"x2"x1" thru 2½"x2½"x1" 853 Sprinkler Hub 1½"x1" thru 2½"x1"

UL 300 300 300 300 300 300 300 300 500 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 250 175 300 NA 300 300 300 300 300

Valves & Components Model RCV Riser Check Valve 726 Y-Strainer SJ-300F Butterfly Valve SJ-700W Butterfly Valve

FM 300 300 500 300 500 300 300 300 NA 300 300 500 300 300 300 300 300 300 300 300 300 300 300 300 300 175 175 175 300 300 300 300 300 300 300

Unit: psi

Size Range 2½" thru 6" 2½" thru 6" 8" thru 12" 2½" thru 6" 2" thru 12"

UL 300 300 175 NA 175

FM 300 NA NA 300 NA

Stainless Steel Series Sch. 40S and 10S Pipe Size in 1 1¼ 2½ 2 2½ 3 4 5 6 8

Sch. 10S Wall (in) 0.109 0.109 0.109 0.109 0.120 0.120 0.120 0.134 0.134 0.148

Unit: psi

SS-7 SS-8 UL FM UL FM 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 250 300 300 300 300

SS-41 SS-723 UL FM Size (in) UL - - 1¼ x ½ 300 350 350 1¼ x ¾ 300 350 350 1¼ x 1 300 350 350 1½ x ½ 300 350 350 1½ x ¾ 300 350 350 1½ x 1 300 350 350 2 x ½ 300 350 350 2 x ¾ 300 350 350 2 x 1 300 350 350

FM 300 300 300 300 300 300 300 300 300

Unit: psi

Model SS-10 90 Elbow SS-11 45 Elbow SS-20 Tee SS-21 Tee SS-21F Tee SS-50 Conc. Reducer SS-50F Conc. Reducer SS-60 Cap SS-80 Flange Adapter

Size Range 1" thru 8" 1" thru 8" 1" thru 8" 3"x2½" thru 4"x2½" 3"x2", 4"x2" 3"x2½" thru 4"x2½" 2½"x2" thru 4" x 2" 1" thru 8" 2" thru 8"

UL 300 300 300 300 300 300 300 300 300

Model C-10 90 Elbow C-11 45 Elbow C-20 Tee C-21 Reducing Tee C-26 Reducing Tee C-50 Conc. Reducer C-52 Conc. Reducer C-60 Cap

Size Range 2" through 4" 2" through 4" 2" through 6" 2½"x2" thrru 6"x5" 2"x¾" thru 4"x½" 2½"x2" thru 6"x5" 2"x1" thru 4"x2" 2" thru 4"

UL 200 200 200 200 200 200 200 200

FM 300 300 300 300 300 300 300 300 300

Copper Tubing Series

Type K & Type L Copper Tubing

Size in 2 2½ 3 4 5 6

Type K Wall (in) 0.083 0.095 0.109 0.134 0.160 0.192

Type L Wall (in) 0.070 0.080 0.090 0.110 0.123 0.140

UL 200 200 200 200 200 200

C301 FM 200 200 200 200 - 200

FM: Type K only


Unit: psi

UL 200 200 200 200 200 200

C341

FM -

Unit: psi

www.shurt.com

FM 200 200 200 NA NA NA NA 200


Catalog 2011

Typical Applications - Flexible Couplings – Sprinkler Systems (NFPA 13)

2. Flexible couplings on horizontal portion of Tie-In Ceiling/floor assembly ≤ 24 in. (610mm)

The following illustrations are part of NFPA 13 – 2007 Annex A

Flexible coupling

Flexible Coupling ≤ 24 in. (610mm)

Explanatory Material. These are for informational purposes only and not a mandatory requirement. For specific requirements for any other areas of sprinkler systems, refer to the latest version of NFPA 13.

1. Flexible couplings for main risers and branch line riser Roof

Roof

24in. (610 mm) Maximum

4-way brace (Pipe must rotate within brace) Flexible coupling

Wall

aming

Roof fr

4-way brace Elbow with flexible ts

≤ 12 in. (305mm) Ceiling/floor assembly FIGURE A.9.3.2.3(2) (a) Flexible Coupling on Horizontal Portion of Tie-In.

3. Flexible Coupling on Main Riser and Branch Line Riser Ceiling/floor assembly

Siding Column

≤ 24 in. (610mm) Flexible coupling

Flexible coupling

Detail A

Flexible coupling

Flexible Coupling

Detail B (Might be preferred for metal buildings)

Flexible coupling

Flexible coupling

Note to Detail A: The four-way brace should be attached above the upper flexible coupling required for the riser and preferably to the roof structure if suitable. The brace should not be attached directly to a plywood or metal deck.

≤ 12 in. (305mm)

FIGURE A.9.3.2(a) Riser Details.

Ceiling/floor assembly FIGURE A.9.3.2.3(2) (b) Flexible Coupling on Main Riser And Branch Line Riser

4. Flexible couplings for drops

Flexible elbow

If dimension is less than 3 ft (0.9m), flexible fitting is not needed.

(A T-connection fitting with flexible ts can be substituted for elbow.)

≤ 24 in. (610mm) [Paragraph 9.3.2.4(1)]

In-rack sprinkler drops Flexible Coupling

Drop s

≤ 24 in. (610mm) [Paragraph 9.3.2.4(3)]

FIGURE A.9.3.2(b) Detail at Short Riser

FIGURE A.9.3.2.4 Flexible Coupling for Drops



Flexible Coupling ≤ 24 in. (610mm) [Paragraph 9.3.2.4(2)]

www.shurt.com

Catalog 2011

5. Seismic Separation Assembly

2 ells 10 in. (254mm) long nipple D

10 in. (254mm) long nipple C

Coupling B

A

2 ts 8 in. (203mm)

Fire sprinkler main

Normal Position

4 in. (102 mm)

4 in. (102 mm)

Fire sprinkler main

Plan

8 in. (203mm)

Longitudinal movement

2 ts and nipple E

8 in. (203mm)

Normal Position

8 in. (203mm)

Vertical movement

Coupling Ell B

A Ell

Normal position

C

Ell Ell

D

Elevation

Nipple E 2 ell lengths 8½ in. (216mm) for 3 in. (76mm) pipe 7½ in. (191mm) for 2½ in. (65mm) pipe

FIGURE A.9.3.3(a) Seismic Separation Assembly. Shown are an 8 in. (203 mm) Separation Crossed by Pipes up to 4 in. (102mm) in Nominal Diameter. For other separation distances and pipe sizes, lengths and distances should be modified proportionally.

6. Earthquake protection for sprinkler piping

4 in. (102 mm)

8 in. (203mm)

Lateral movement

Horizontal Views

7. Typical Location of Bracing on a Looped System

40 ft

40 ft

(12 m)

(12 m)

Longitudinal brace (two-way)

A No bracing

B Lateral brace (two-way) Longitudinal brace (two-way)

B F

E D

Building 1

B

FIGURE A.9.3.5.6 (a)

C

C

Building 2

A Four-way brace at riser B Lateral brace C Lateral brace D Short drop [Figure A.9.3.2(b)] E Couplings at wall penetration F Longitudinal brace


Four-way brace

FIRURE A.9.3.5.6 (d) Typical Location of Bracing on a Looped System.

Systems having more flexible couplings than required above shall be provided with additional sway bracing. A lateral brace shall be provided within 24” (600mm) of every other coupling unless pipes are ed by rods less than 6” (152mm) long from the ceiling or by U-type hooks underside of the structural element. (NFPA 13 – 2007 9.3.2. & 9.3.5.)

www.shurt.com


Catalog 2011

HVAC, St. Mary’s Hospital, Seoul, Korea

HVAC, Praktiker warehouse, Iraklion Krete, Greece

HVAC, Microsoft facility, Puerto Rico



www.shurt.com

Catalog 2011

Temporary Speed Skating Rink, Halifax, Nova Scotia, Canada

Holiday Inn Swimming Pool Pump Room, Las Vegas, NV

HVAC, Taichung City Government Office, Taichung, Taiwan

Westside Regional Wastewater Treatment, BC, Canada HVAC, Tamkang University, Lanyang, Taiwan


www.shurt.com


Catalog 2011

East Side CSO tunnel boring project, Portland, OR

Ik-san E-Mart, Seoul, Korea

Manifold connections, Rain for Rent, Las Vegas, NV

Water treatment plant, Ouray, UT



www.shurt.com

Catalog 2011

HVAC, King Abudullah Financial District, KSA

Fire Protection Systems, Dubai Metro, UAE

Ski Dome glycol pipelines, Dubai, UAE

Fire Protection Systems, Tamkang University, Lanyang, Taiwan


HVAC, Seven Stars Technology Building, Taipei, Taiwan

www.shurt.com


Catalog 2011

and Conditions Controlling Provisions:

These and conditions shall control with respect to any and all

purchase orders or sales of Shurt products.

No alteration, modification or waiver of these and conditions whether on the customer's purchase order or otherwise shall be valid

Weights:

All weights are approximate and subject to change without notice. Always specify gasket grade when ordering and double check the gasket grade received to be sure it is suited for the service intended.

unless the alteration, modification or waiver is specifically accepted in

Shurt reserves the right to change or modify product designs,

Inc.

incurring obligation. Prices and and Conditions of Sale are

writing by an authorized representative of Shurt Piping Products,

specifications and/or standard equipment without notice and without subject to change without notice.

Shipping :

All orders are quoted F.O.B. shipping point unless otherwise agreed upon in writing.

Warranty:

We warrant all Shurt products to be free from defects in

Orders are accepted subject to approval by our Head Office and Credit Department and are contingent upon acts of God, war, civil unrest or disturbance, strikes, labor difficulties, governmental regulations or rulings, delays of carriers (land, air or ocean), inability to obtain materials, accidents or any other cause beyond our control. Shipping dates are estimated, and we will do our best to ship within the time estimated. We cannot guarantee shipping dates, and in the event of a production or shipment delay, we reserve the right to change the estimated shipping date. Under no circumstances shall Shurt be liable for damages of any kind, including but not limited

to incidental or consequential damages for lost sales or profits or liquidated damages, directly or indirectly arising from delays or failure to meet shipping dates.

materials and workmanship under normal conditions of use and service. Our obligation under this warranty is limited to repairing or replacing at our option at our factory or designated facility any product which shall within 10 years after delivery to the original buyer be returned with transportation charges prepaid, and which our examination and inspection shall show to our satisfaction to have been defective. This warranty is made expressly in lieu of any other warranties, express or implied, including any implied warranty of merchantability or fitness for a particular purpose. The buyer's sole and exclusive remedy shall be for the replacement or repair of defective products as provided herein. The buyer agrees that no other remedy (including but not limited to), incidental or consequential damages for lost profits, lost sales, injury to person or property or any other

Orders accepted cannot be changed or cancelled without our written consent.

incidental or consequential loss shall be available to him/her. Shurt neither assumes nor authorizes any person to assume

Orders for special (non-standard) goods may not be cancelled, nor will we accept return of these goods for credit.

Claims For Shortages:

All claims for shortages must be made within 10 days of receipt of goods. Our responsibility ceases when the goods are delivered to the carrier in good condition. Carriers are responsible for goods lost, damaged or delayed in transit. For your own protection have the transportation company's agent any damage, shortage or delay and note them on the freight bill over his/her signature.

for it any other liability in connection with the sale of such products.

Items purchased by Shurt and resold will have the original

equipment manufacturers warranty extended to Shurt customers where applicable. This warranty shall not apply to any product which has been the subject to misuse, negligence or accident, which has been repaired or altered in any manner outside of Shurt's factory or designated facility or which has been used in a manner contrary to Shurt's instructions, recommendations or generally accepted practices. Shurt shall not be responsible for design errors due to inaccurate or incomplete information supplied by the buyer or his representatives. (Effective July 1, 1998)



www.shurt.com

Catalog 2011

Index Model No.

Page No.

49 . . . . . . . . . . . . . . . . . . . . . 30 55 . . . . . . . . . . . . . . . . . . . . . 51 56 . . . . . . . . . . . . . . . . . . . . . 51 57 . . . . . . . . . . . . . . . . . . . . . 55 58 . . . . . . . . . . . . . . . . . . . . . 55 59 . . . . . . . . . . . . . . . . . . . . . 55 71 . . . . . . . . . . . . . . . . . . . . . 97 79 . . . . . . . . . . . . . . . . . . . . 110 651 . . . . . . . . . . . . . . . . . . . . 85 723 . . . . . . . . . . . . . . . . . . . . 38 726 . . . . . . . . . . . . . . . . . . . . 88 728 . . . . . . . . . . . . . . . . . . . . 89 811 . . . . . . . . . . . . . . . . . . . . . 93 812 . . . . . . . . . . . . . . . . . . . . 93 813 . . . . . . . . . . . . . . . . . . . . 93 814 . . . . . . . . . . . . . . . . . . . . 93 815 . . . . . . . . . . . . . . . . . . . . 94 815 . . . . . . . . . . . . . . . . . . . . 93 816 . . . . . . . . . . . . . . . . . . . . 94 817 . . . . . . . . . . . . . . . . . . . . 94 818 . . . . . . . . . . . . . . . . . . . . 94 819 . . . . . . . . . . . . . . . . . . . . 95 820 . . . . . . . . . . . . . . . . . . . . 95 825 . . . . . . . . . . . . . . . . . . . . 95 827 . . . . . . . . . . . . . . . . . . . . 95 830 . . . . . . . . . . . . . . . . . . . . 96 831 . . . . . . . . . . . . . . . . . . . . 95 832 . . . . . . . . . . . . . . . . . . . . 95 841 . . . . . . . . . . . . . . . . . . . . 96 850 . . . . . . . . . . . . . . . . . . . . 52 851 . . . . . . . . . . . . . . . . . . . . 52 853 . . . . . . . . . . . . . . . . . . . . 52 899 . . . . . . . . . . . . . . . . . . . . 51 901 . . . . . . . . . . . . . . . . . . . . 49 903 . . . . . . . . . . . . . . . . . . . . 49 7041 . . . . . . . . . . . . . . . . . . . 28 7043 . . . . . . . . . . . . . . . . . . . 30 7110 . . . . . . . . . . . . . . . . . . . . 43 7111 . . . . . . . . . . . . . . . . . . . . 43 7112 . . . . . . . . . . . . . . . . . . . . 43 7113 . . . . . . . . . . . . . . . . . . . . 43 7114 . . . . . . . . . . . . . . . . . . . . 53 7120 . . . . . . . . . . . . . . . . . . . 44 7121 . . . . . . . . . . . . . . . . . . . 45 7122 . . . . . . . . . . . . . . . . . . . 53 7125 . . . . . . . . . . . . . . . . . . . 50 7127 . . . . . . . . . . . . . . . . . . . 49 7130 . . . . . . . . . . . . . . . . . . . 44 7133 . . . . . . . . . . . . . . . . . . . 53 7135 . . . . . . . . . . . . . . . . . . . 44 7137 . . . . . . . . . . . . . . . . . . . 48 7150 . . . . . . . . . . . . . . . . . . . 46 7151 . . . . . . . . . . . . . . . . . . . 46

Model No.

Page No.

7160 . . . . . . . . . . . . . . . . . . . 47 7170 . . . . . . . . . . . . . . . . . . . 32 7180 . . . . . . . . . . . . . . . . . . . 31 7181 . . . . . . . . . . . . . . . . . . . 31 7705 . . . . . . . . . . . . . . . . . . . 18 7706 . . . . . . . . . . . . . . . . . . . 22 7707 . . . . . . . . . . . . . . . . . . . 19 7721 . . . . . . . . . . . . . . . . . . . 35 7722 . . . . . . . . . . . . . . . . . . . 37 10EP . . . . . . . . . . . . . . . . . . . 58 11EP . . . . . . . . . . . . . . . . . . . 58 20EP . . . . . . . . . . . . . . . . . . . 58 22EP . . . . . . . . . . . . . . . . . . . 58 35EP . . . . . . . . . . . . . . . . . . . 58 650N . . . . . . . . . . . . . . . . . . . 84 7110-B . . . . . . . . . . . . . . . . . . 48 7110DR . . . . . . . . . . . . . . . . . 49 7110LR . . . . . . . . . . . . . . . . . 48 7111LR . . . . . . . . . . . . . . . . . 48 7112G . . . . . . . . . . . . . . . . . . 48 7150F . . . . . . . . . . . . . . . . . . 50 7150M . . . . . . . . . . . . . . . . . . 50 7160H . . . . . . . . . . . . . . . . . . 47 7160P . . . . . . . . . . . . . . . . . . 47 7160T . . . . . . . . . . . . . . . . . . 47 725F . . . . . . . . . . . . . . . . . . . 86 72C . . . . . . . . . . . . . . . . . . . . 98 72R . . . . . . . . . . . . . . . . . . . . 98 7706-T . . . . . . . . . . . . . . . . . . 25 7707L . . . . . . . . . . . . . . . . . . 21 7707N . . . . . . . . . . . . . . . . . . 20 7771-T . . . . . . . . . . . . . . . . . . 25 A10 . . . . . . . . . . . . . . . . . . . 133 A10R . . . . . . . . . . . . . . . . . . 134 A11 . . . . . . . . . . . . . . . . . . . 133 A12 . . . . . . . . . . . . . . . . . . . 133 A13 . . . . . . . . . . . . . . . . . . . 133 A20 . . . . . . . . . . . . . . . . . . . 134 A25 . . . . . . . . . . . . . . . . . . . 134 A50 . . . . . . . . . . . . . . . . . . . 134 A505 . . . . . . . . . . . . . . . . . . 131 A507 . . . . . . . . . . . . . . . . . . 132 A512 . . . . . . . . . . . . . . . . . . 132 A60 . . . . . . . . . . . . . . . . . . . 133 B20 . . . . . . . . . . . . . . . . . . . . 96 B24 . . . . . . . . . . . . . . . . . . . . 96 C10 . . . . . . . . . . . . . . . . . . . 122 C10-W . . . . . . . . . . . . . . . . . 122 C11 . . . . . . . . . . . . . . . . . . . 122 C11-W . . . . . . . . . . . . . . . . . 122 C20 . . . . . . . . . . . . . . . . . . . 122 C20-W . . . . . . . . . . . . . . . . . 122 C21 . . . . . . . . . . . . . . . . . . . 123


Model No.

Page No.

C26 . . . . . . . . . . . . . . . . . . . 123 C305 . . . . . . . . . . . . . . . . . . 119 C306 . . . . . . . . . . . . . . . . . . 120 C307 . . . . . . . . . . . . . . . . . . 121 C341 . . . . . . . . . . . . . . . . . . 121 C50 . . . . . . . . . . . . . . . . . . . 123 C52 . . . . . . . . . . . . . . . . . . . 124 C55 . . . . . . . . . . . . . . . . . . . 124 C55T . . . . . . . . . . . . . . . . . . 125 C60 . . . . . . . . . . . . . . . . . . . 122 C-7 . . . . . . . . . . . . . . . . . . . . . 24 C723 . . . . . . . . . . . . . . . . . . 126 C726 . . . . . . . . . . . . . . . . . . 127 DE30-GG . . . . . . . . . . . . . . . 125 G-28 . . . . . . . . . . . . . . . . . . . 23 H305 . . . . . . . . . . . . . . . . . . 113 H307 . . . . . . . . . . . . . . . . . . 114 H312 . . . . . . . . . . . . . . . . . . 115 L11-3D . . . . . . . . . . . . . . . . . . 56 L11-5D . . . . . . . . . . . . . . . . . . 57 L11-6D . . . . . . . . . . . . . . . . . . 57 L22-3D . . . . . . . . . . . . . . . . . 56 L22-5D . . . . . . . . . . . . . . . . . 57 L22-6D . . . . . . . . . . . . . . . . . 57 L30-3D . . . . . . . . . . . . . . . . . 56 L30-5D . . . . . . . . . . . . . . . . . 57 L30-6D . . . . . . . . . . . . . . . . . 57 L45-3D . . . . . . . . . . . . . . . . . 56 L45-5D . . . . . . . . . . . . . . . . . 57 L45-6D . . . . . . . . . . . . . . . . . 57 L60-3D . . . . . . . . . . . . . . . . . 56 L60-5D . . . . . . . . . . . . . . . . . 57 L60-6D . . . . . . . . . . . . . . . . . 57 L90-3D . . . . . . . . . . . . . . . . . 56 L90-5D . . . . . . . . . . . . . . . . . 57 L90-6D . . . . . . . . . . . . . . . . . 57 M21 . . . . . . . . . . . . . . . . . . . . 34 M22 . . . . . . . . . . . . . . . . . . . . 36 M-7 . . . . . . . . . . . . . . . . . . . . 14 R-88 . . . . . . . . . . . . . . . . . . . 101 R-88 . . . . . . . . . . . . . . . . . . . 103 R88N . . . . . . . . . . . . . . . . . . 102 RCV . . . . . . . . . . . . . . . . . . . . 90 RH-1000 . . . . . . . . . . . . . . . 104 RJ-10 . . . . . . . . . . . . . . . . . . 106 RJ-11 . . . . . . . . . . . . . . . . . . 106 RJ-20 . . . . . . . . . . . . . . . . . . 106 RJ-21 . . . . . . . . . . . . . . . . . . 107 RJ-50 . . . . . . . . . . . . . . . . . . 107 RJ-51 . . . . . . . . . . . . . . . . . . 107 RJ-60 . . . . . . . . . . . . . . . . . . 106 RJ-70 . . . . . . . . . . . . . . . . . . 107 RX-3000 . . . . . . . . . . . . . . . 104

Model No.

Page No.

RX-3770 . . . . . . . . . . . . . . . 105 S35 . . . . . . . . . . . . . . . . . . . 109 SD-28 . . . . . . . . . . . . . . . . . 109 SJ-200 . . . . . . . . . . . . . . . . . . 77 SJ-300F . . . . . . . . . . . . . . . . . 79 SJ-300N . . . . . . . . . . . . . . . . 78 SJ-400 . . . . . . . . . . . . . . . . . . 74 SJ-500L . . . . . . . . . . . . . . . . . 80 SJ-500W . . . . . . . . . . . . . . . . 80 SJ-600L . . . . . . . . . . . . . . . . . 73 SJ-600W . . . . . . . . . . . . . . . . 73 SJ-900 . . . . . . . . . . . . . . . . . . 81 SJ-915 . . . . . . . . . . . . . . . . . . 82 SJ-930 . . . . . . . . . . . . . . . . . . 83 SJ-C300 . . . . . . . . . . . . . . . 128 SS-10 . . . . . . . . . . . . . . . . . . 68 SS-11 . . . . . . . . . . . . . . . . . . . 68 SS-1200 . . . . . . . . . . . . . . . . 66 SS-20 . . . . . . . . . . . . . . . . . . 68 SS-21 . . . . . . . . . . . . . . . . . . 69 SS-28 . . . . . . . . . . . . . . . . . . 67 SS-41 . . . . . . . . . . . . . . . . . . 71 SS-5 . . . . . . . . . . . . . . . . . . . 61 SS-50 . . . . . . . . . . . . . . . . . . 69 SS-60 . . . . . . . . . . . . . . . . . . 68 SS-7 . . . . . . . . . . . . . . . . . . . 62 SS-723 . . . . . . . . . . . . . . . . . 72 SS-726 . . . . . . . . . . . . . . . . . 72 SS-7X . . . . . . . . . . . . . . . . . . 63 SS-8 . . . . . . . . . . . . . . . . . . . 64 SS-80 . . . . . . . . . . . . . . . . . . 71 SS-8X . . . . . . . . . . . . . . . . . . 65 W110 . . . . . . . . . . . . . . . . . . . 54 W110LR . . . . . . . . . . . . . . . . 54 W111LR . . . . . . . . . . . . . . . . . 54 W120 . . . . . . . . . . . . . . . . . . . 54 W121 . . . . . . . . . . . . . . . . . . . 54 W150 . . . . . . . . . . . . . . . . . . . 55 W151 . . . . . . . . . . . . . . . . . . . 55 W160 . . . . . . . . . . . . . . . . . . . 54 WS-10 . . . . . . . . . . . . . . . . . . 70 WS-10L . . . . . . . . . . . . . . . . . 70 WS-11 . . . . . . . . . . . . . . . . . . 70 WS-20 . . . . . . . . . . . . . . . . . . 70 WS-21 . . . . . . . . . . . . . . . . . . 70 WS-50 . . . . . . . . . . . . . . . . . . 70 WS-60 . . . . . . . . . . . . . . . . . . 70 XH-1000 . . . . . . . . . . . . . . . . 17 XH-70EP . . . . . . . . . . . . . . . . 26 Z05 . . . . . . . . . . . . . . . . . . . . 15 Z07 . . . . . . . . . . . . . . . . . . . . 16

www.shurt.com


Shurt 2011 Catalog 3rg5o

Overview 5o1f4z

More details 6z3438

Related Documents c2h70

Shurt 2011 Catalog 3rg5o

2016-2017 Shurt General Catalog 3r5b4p

Catalog 2011 1665j

Catalog 2011 1665j

Thule Catalog 2011 145z5b

2011 Invicta Catalog Lo 426044