RICOH AFICIO 3800C error SC385 • LinkBack ○ LinkBack URL ○ About LinkBacks ○ ○ Bookmark & Share ○ Digg this Thread! ○ Add Thread to del.icio.us ○ Bookmark in Technorati ○ Tweet this thread •
Thread Tools ○ Show Printable Version ○ Email this Page… ○ Subscribe to this Thread…
•
Display
○ Linear Mode ○ Switch to Hybrid Mode ○ Switch to Threaded Mode 1.
01-30-2005 #1
SonyaN Guest RICOH AFICIO 3800C error - SC385 Disclaimer: I am not a tech. I am the printer owner who owns her own small home business and can\\\'t afford a printer tech. LOL. I am getting a SC385 error. Can anyone tell my what this error refers to and how to fix it? In laymans , please. I\\\'m pretty handy, I just need some direction. ○
Share
Share this post on
Digg
Del.icio.us
Technorati
Twitter
Reply With Quote 2. 02-13-2005 #2 Mike B Guest Re:RICOH AFICIO 3800C error SC385 Yesterday I spent a little time looking for the information for you. However seems Ricoh holds it pretty close to the vest on this error code business. This seems to be a fairly new forum and maybe you should post it in another as we may not have a
Ricoh technician avialable here yet. I also don\'t know if it is possible for you but they say on there site that you can call there salesman on error codes. Of coarse you know that they will want to send a technician to your door. If you can figure out what the code means we can give you general information on the laser process and tests to check some things and might be able to help you than. I did look in there manual and did not see it listed. Hope this helps ○
Share
Share this post on
Digg
Del.icio.us
Technorati
Twitter
Reply With Quote 3. 02-15-2005 #3
[email protected] Guest Re:RICOH AFICIO 3800C error SC385 SC385: Vsg Adjustment Error The LCD displays SC385 when the output from the ID sensor is found to be outside 1.8 ± 0.05 V during Vsg adjustment. Turning the power off then on resets this condition. However, SC385 is lit again after the end of each copy job even when this SC condition is reset by turning the power off then on. Toner is still
supplied, but using fixed supply mode, until a subsequent Vsg adjustment is successful. For Starters · Dirty ID sensor · Poor connection of connector · Defective ID sensor · Poor cleaning 1. Clean the ID sensor. 2. Check if the sensor connector is properly connected. 3. Replace the ID sensor. 4. Check the drum cleaning unit. ○
Share
Share this post on
Digg
Del.icio.us
Technorati
Twitter
Reply With Quote
4.
02-18-2005 #4
Tonerbomb
Service Manager 250+ Posts Date Feb 2005 Posts 436 Rep Power 18 Re:RICOH AFICIO 3800C error SC385 You could try new pcu\'s for color and black, but I have found that the paper transfer belt is a more likly cause if it is persistant. This is not a replacable part, unless your
real techy and mechanically inclined Post edited by: tonerbomb, at: 2005/02/17 19:16 Post edited by: tonerbomb, at: 2005/02/19 10:26 ○
Share
Share this post on
Digg
Del.icio.us
Technorati
Twitter
Never trust a computer you can't throw out a window!!! Reply With Quote 5.
02-19-2005 #5
been there Guest
Re:RICOH AFICIO 3800C error SC385 hmy: i had a machine with the same code...unplug machine and disconnect the hv connector that supplt bias to dv units and ohm them out...you will find one is shorted to ground...take the grounded bias termenaloff at the dv end and clean real good...toner causing the short ○
Share
Share this post on
Digg
Del.icio.us
Technorati
Twitter
Reply With Quote 6.
04-09-2007 #6
Scott_Lewis
Field Supervisor 500+ Posts
Date Mar 2007 Location Great Falls, Montana Posts 527 Rep Power 15 Originally Posted by SonyaN
Disclaimer: I am not a tech. I am the printer owner who owns her own small home business and can\\\'t afford a printer tech. LOL. I am getting a SC385 error. Can anyone tell my what this error refers to and how to fix it? In
laymans , please. I\\\'m pretty handy, I just need some direction. Try cleaning the toner density sensor. I -think- it is just uphill from the black pcu. Pull out the K pcu and the belt tray and you should be able to see it. Scott