Reviewer (7) 3l602z

MACHINE DESIGN PART I

BY: JACSTONE REVIEW CENTER

Chuck used on turret lathe is A. collet chuck B. four jaw self centering chuck C. Magnetic Chuck D. Three jaw independent chuck Answer: D Angle plate is used for A. cutting gears in a shaper B. cutting gears in a milling C. cutting tapers in a lathe D. fixing job cut angles is grinder Answer: A For machining the flange of 90 elbow on a lathe, which of the following device is used? A. Angle plate B. Catch Plate C. Face Plate D. Lathe plate Answer: C Angle Plate is used for A. cutting gears in a shaper B. cutting gears in a milling C. cutting tapers in a lathe D. fixing job cut angles is a grinder Answer

A

A sine bar can not be used without a/ an A. angle gage B. micrometer C. slip gage D. vernier caliper Answer: A The operation of finishing a drilled hole to the correct size is known as A. counting boring B. counter sinking C. reaming D. spot facing

When cutting material in a lathe, the harder the material being cut, the tool bit should have A. less side rake B. more side rake C. more top rake D. no side rake Answer: A On xx heavy pipe the extra metal is added in the A. outside B. inside C. half on the inside, half on the outside D. three quarters on the outside, one quarter on the inside Answer: B Valve seats are usually: A. screwed in B. dropped in C. pressure in D. A or C Answer: D When grinding in valves the disc is secured to the stem by: A. inserting a cotter pin B. placing emery cloth between stem and disc C. welding D. A or B Answer: D A fresh-water tank is located at the top. What will the pressure on it outlet in the engine room 50’ below the tank? A. 20 psi B. 21.7 psi C. 23 psi D. 25 psi Answer: B

Answer: C Carbon steel drill should be operated at A. speed less than that when using a high speed drill B. speed greater than that when using a high speed drill C. the different speed as that when using high speed drill D. the same speed as that when using a high speed drill

In a duplex reciprocating pump: A. the slide valve for the one cylinder is controlled in the piston of the other cylinder B.both slide valves operate simultaneously C. each slide valve is controlled by its own piston rod D. one slide valve operates the other slide valve Answer: A

Answer:

B

The jerky operation of a reciprocating pump may be caused by A. small leaks in the suction line B. suction valve only partially open C. dirty suction valve D. any of the above

The process used to retard compression trust on iron pipe and fitting is called: A. timming B. soldering C. galvanizing D. sulphurizing

Answer: D Answer: C It is used in the production of the flat surface on pieces two large or too heavy to hold in a shaper. A. Grinder B. Planer C. Shaper D. Shaver

The system used for breaking scale from the evaporator coils while the evaporator is in operation is called: A. recirculating B. blowing-down C. cracking-off D. dumping

Answer: B A machine tool used to produce a variety of surface of surfaces by using a circular type cutter with multiple teeth called A. broaching machine B. grinding C. lathe machine D. milling machine

Answer: C

Answer D

Answers: B

Cutting tool used to finish internal and external surfaces by the use of cutter called a broach, which has a series of cutting edges of teeth. A. Broaching machine B. Lathe machine C. Planer D. Shaper

When distilling salt water the cooling – water discharge from the distiller is fed back to the evaporator as feedwater: A. to cut down on the amount of cooling water needed B. to prevent n excess amount of cooling water from being discharge to the bilges C. to supply hot water to the evaporator for more economical operation D. none of the above

The coils in the evaporator are attached to the headers by: A. pipe nipples B. union – type fitting C. welding D. bolted flanges

Answer: A Answer: C Group of thin steel strips used for measuring clearances. A. Tachometer B. Micrometer C. Feeler gage D. Caliper

An “offset” in pipe fitting refers to: A. a cut-off running at right angles to the original piping B. two pipes running parallel to each other C. a bend in the pipe D. two sizes of pipe in the same run

Answer C Answer: C Bind of chuck, which should not be used where accuracy desired called A. collet chuck B. four jaw shuck C. magnetic chuck D. universal chuck

If a piston-type flush valve is not operating properly, the most likely cause would be: A. a plugged by – hole B. a cracked diaphragm C. a stuck pilot valve D. any of the above

Answer D Answer: A

Before installing a sure that the: A. flange faces are B. isolating valves C. flange faces are D. old gasket is in

new flange gasket be painted are open absolutely clean place

A machine tool, which is very similar to a shaper except the ram reciprocals vertically rather that horizontally A. Lathe B. Grinder C. Planer D. Slotter

Answer: C What is a standard wire gage: A. #10 larger B. #25 is smaller than #20 C. # 1 is smaller than # 2 D. # 30 is larger than # 25 Answer: B Which of the following tools would be most useful when taking leads on bearings A. dividers B. outside calipers C. micrometer D. center gage Answer: C The wrench size for a ¼” nut is: A. 1-1/4. B. 1-1/2 C. 3/4 D. 10/24 Answer: A Which of the following would cause hot bearings? A. improper oil B. dirt in oil C. improper alignment D. all of the above

Answer D The operation of machining the end of a work piece to make a square with the axis. A. Buffing B. Honing C. Lapping D. Squaring Answer: D The operation of enlarging a hole by means of an adjustable cutting tool with only one cutting edge. A. Boring B. Broaching C. Drilling D. Milling Answer: A It is used to true and align machine tools fixtures and works is at and inspect size trueness of finished work, and to compare measurements either heights or depths or many other measurements. A. Dial Gage B. Dial Indicator C. Tachometer D. Speedometer Answer: B

Answer: D Melting point of Babbit is approximately: A. 1000 deg. F B. 650 deg. F C. 750 deg. F D. 500 deg. F

A tool used for measuring diameters. A. Caliper B. Manometer C. Tachometer D. Pyrometer Answer: A

Answer: B What is pouring Babbit in: A.can be poured in several pourings B. must be poured all at one time C. can be done at intervals D. must be done in cool place

A process of forming metals by the use of dies after the metal is forced to its plastic range. A. Casting B. Forging C. Rolling D. Turning

Answer: B Answer: C

Which of the following does not have to be lubricated when drilling? A. Steel B. Brass C. Monel D. Tool Steel

A mechanism, which usually does the indexing in a machine tool is called: A. dividing head B. indexing C. slotter D. universal chuck

Answer: B

Answer: A

The tool to use when cutting a hole in the side of a round piece of metal is called a: A. vine B. jaw holder C. “V” block D. chuck

Recommended best cutting angle of drill for work on steel or cast iron is ______ degrees A. 48 B. 50 C. 59 D. 63 Answer: C

Answer: C When measuring a drill for size measure across the: A. margin B. flutes C. shank D. point

What is the common shop practice to prevent soldering from running away from surface to be ed? A. All of these B. Introduce around the work rolled wet cloth C. Put asbestos sheeting around the work D. Surround the work with clay

Answer: A Answer: A N.C. stands for: A. neutral cut B. national coarse C. national cut D. not center Answers: B N.F. stands for: A. national file B. national fine C. neutral file D. not found Answer: B The tool used in precision work to smooth or enlarge holes is called a: A. round out B. drift pin C. reamer D. protractor

A machinery operation where by done with the work accurately fastened has a reciprocating motion and the tool head is stationary is called: A. planning B. reaming C. shaping D. turning Answer: A What is the difference between the shaper and a planer? A. The shaper can perform slotting operation while the planer cannot B. The shaper handles large pieces while the planer handles only small pieces C. The tool of the shaper moves while the planer is stationary D. The tool of the shaper moves in reciprocating motion while the tool in the planer moves in rotary motion.

Answer: C

Answer: C

Which of the following chisels would be used for cutting oil grooves? A. diamond-point chisel B. cold chisel C. round-nose chisel D. hot chisel

Test sometimes referred to as upsetting test called A. bend B. crush C. flange D. flaring

Answer: C

Answer: A

Valve stem packing is A. O. D. of the valve of the packing gland B. Top of the packing of the gland C. O. D. of the valve of the packing box D. I. D. of the valve bottom of the gland

measured from thin: stem to the bottom

stem to the I. D.

The process used to retard corrosion on iron pipe is called: A. soldering B. annealing C. tempering D. galvanizing

stem to the to the

Answer: D

gland to the bottom

Answer: C Tool used to cut threads on pipe is called a: A. pipe tool B. pipe stock C. pipe vise D. pipe cutter Answer: B The pipe fitting which has two opening and provides a turn of 90 deg. Is called: A. an elbow B. a toe C. a coupling D. a union

Which of the following tools does not belong to the group?. A. Divides B. Double VEE block C. Caliper D. Trammel Answer: B In machine shop had forging operation of lengthening a piece of stock while reducing the cross-sectional area of work is called: A. bloating B. draining C. spreading D. upsetting Answer: D

Answer: A A plug cock offers: A. more resistance to flow than a valve B. the same resistance to flow as valve C. less resistance to flow than a valve D. the same resistance to flow as valve

globe a globe

Which of the following services is not considered to be a work of a machinist? A. grinding B. Honing C. Overhauling D. Reboring

globe Answer: C a angle

Answer: C The most common flux to use when soldering brass, copper or tin is: A. hallow B. rosin C. borax D. salt ammonia Answers: B One turn of the screw on a micrometer moves the spindle: A. .25 B. .205 C. .0205 D. .2005

Common defects encountered in the foundry shop steel casting operation and also in welding practices A. Blow / pin holes B. Cold shot C. Cracks D. Parting line Answers: A Lathe operator to remove the taper shank from the taper hole drift. It is also called: A. chuck taper B. Morse taper C. tapered key D. tong Answer: B

Answer: C

Before drilling a hole in a piece of metal, It should be A. mark with chalk B. center-punch C. scribed D. protracted

When turning a piece of round metal in a lathe, the front clearance should be smaller for: A. large-diameter cutting B. small-diameter cutting C. cutting angles D. none of the above

Answer B A tap or die marked ¼-20 indicates: A. ¼ radius – 20 cm. long B. ¼ radian – 20 threads per in. C. ¼ diameter – 20 threads per in. D. ¼ turn – 20 times Answer: C After a piece of piece of pipe has been cut, the hole is cleaned out with a: A. piper reamer B. pipe cleaner C. pipe taper D. hole cleaner Answer: A The tool used for cutting pipe threads is called a: A. pipe cutter B. pipe stock and die C. pipe threader D. pipe ratcher cutter Answer: B The tool used when working with larger sizes of pipe is called a: A. chain pipe wrench B. chain tongs C. chain holder D. A or B Answer: D The tool used when preparing to put fittings on copper tubing is called a: A. tube spreader B. flaring tool C. tube retarder D. tube countersink Answer: B Which of the following is not a standard thread form? A. Square B. American national C. Double Flute D. 60 deg. Sharp V

Answer: B When cutting material in a lathe, the harder the material being cut, the tool bit should have: A. more side rake B. less side rake C. more top rake D. no side rake Answer: B Knurling is done to: A. smooth material B. polish material C. roughen material D. sharpen material Answer: C Removing the sharp edges from a piece of stock is reffered to as: A. knurling B. chamfering C. planning D. turning Answer: B Carbon steel drills should be operated at: A. speeds greater than that when using a high-speed drill B. speeds less than that when using a high-speed drill C. the same speed as that when using a high-speed drill D. none of the above Answer: B When extreme outer corners of the cutting edges of a drill was away too rapidly, it is an indication of: A. not enough speed B. too much rake angle C. too high speed D. B or C Answer: D

Answer: C

It is an operation of stretching or spreading over the metal by means of the plane of the hammer. A. Bending B. Peening C. Swaging D. Upsetting

If the angle on a drill is less than 59 deg.: A. the drill will make a large hole B. the drill will make a smaller hole C. the hole will take longer to drill and more power is required to drive the drill D. the drill will not center properly

Answer: B

Answer: C

The good quality of a measuring tool A. should be easy to handle B. should be easy to read C. should be wear resistance D. all of the above

Soda added to water is used for cooling instead of plain water because: A. it reduces the amount of heat generated B. it improves the finish C. it overcome rusting D. all of the above

Answer: D The flatness of surface can be checked A. by using straight edge B. by using surface plate C. by using dial test indicator D. all of the above

Answer: D If A. B. C. D.

a drill speed is too great, it will: cut faster lose its temper cut slower not cut

Answer: D A holding device which is used to hold or grip work piece, while filling, chipping or any other bench work or while machining or drilling them A. clamp B. grid C. pressed D. vise

Answer: B

Answer: D

Answer: C

A multi pointed hand anything tool used to removed material from metallic and non-metallic work pieces to match with drawing, shape and size. A. Cold chisel B. File C. Hacksaw D. Hammer

If the cutting edges of a drill are cut at different angles: A. the drill will not cut B. the hole will be larger than the drill C. the hole will be smaller than the drill D. none of the above

Answer: B

Answer: B

A side-cutting tool used for accurately finishing the straight or tapered holes already drilled or bored. A. Peering B. Reamer C. Swaging D. Tapping

The correct cutting angle on a drill for ordinary work is: A. 45 deg. B. 50 deg. C. 59 deg. D. 65 deg.

Answer: B

Answer: C

The lip clearance of a drill should be approximately: A. 20 deg. – 25 deg. B. 5 deg. – 10 deg. C. 12 deg. – 15 deg. D. 15 deg. – 20 deg.

Which of the following gives greater hardness, cutting toughness and dine grain structure? A. Chromium B. Nickel C. Tungsten D. Vanadium Answer: A It is a process to impact maximum hardness to the steel part. A. Annealing B. Hardening C. Normalizing D. Tempering Answer: B The size by which it is referred to as a matter of convenience called: A. actual size B. basic size C. effective size D. nominal size Answer: D The relation between two mating parts with reference to ease the assembly is called A. allowance B. clearance C. tolerance D. fits Answer: D It is an operation of finishing cylindrical surfaces to a fine degree of accuracy buy means of abrasive sticks. A. Honing B. Lapping C. Planing D. Shaping

In referring to threads, “pitch” is: A. the distance of the full length of the thread B. the distance from a point on one thread to a corresponding point on the next thread measured parallel to the axis C. the distance from the top of one thread to the bottom of the next thread D. the distance from the bottom of a head on a bolt to the first thread Answer: B A tool bit for cutting an American National thread should be ground with a: A. 45 deg. angle B. 90 deg. angle C. 60 deg. angle D. 30 deg. angle Answer: C An approximate safe rule for cutting new piston rings for steam pumps is to make the ring: A. .002” between piston and cylindrical for each inch diameter of piston B. .001” between piston and cylinder for each inch diameter C. .010 between piston and cylinder for each inch diameter of piston D. .0001” between piston and cylinder for each inch diameter of piston Answer: B An approximate safe rule for cutting new piston rings for steam pumps is to make the ring: A. 1/32” larger in diameter per inch diameter of cylinder B. 1/16” larger in diameter than that of the cylinder C. 1/16” larger in diameter per inch diameter of cylinder D. .005” larger in diameter per inch diameter of cylinder Answer: C

Answer: A It is device, which hold the job in position and guide the cutting tool. A. clamp B. grip C. jig D. vise Answer: C

The gap clearance for new piston rings for steam pumps should be approximately: A. .003” for each inch diameter of cylinder B. .001” for each inch diameter of cylinder C. .010” for each inch diameter of cylinder D. .050” for each inch diameter of cylinder Answer: A

What does 3/8 – 16 mean to you? A. 16 pieces, 3/8 “ long B. gear with 16 teeth and a 3/8” arbor hole C. 3/8” square, 16” long D. 3/8” diameter. 16 threads per inch

A machine element inserted parallel to the axis of a shaft. A. cutter B. fastener C. key D. reamer

Answer: D

Answer: C

When using a drill press the work should be held with: A. the hand B. a gloved hand C. a vise or clamp D. pliers

A machine element inserted at right angle to the axis of shaft is known as A. clamp B. cutter C. fastener D. key

Answer: C

Answer: B

Tapered shanks are used on large drfill presses so that: A. the drill can be centered more easily B. the drill can be easily forced out of the sleeve with a drift C. the shank will not turn when cutting D. the shank can be reground when worn

The process of extracting iron in a blast furnace is called A. casting B. manufacturing C. smelting D. sintering Answer: C

Answer: B Which of the following is not a common drill shank? A. straight B. taper C. fluted D. bit

Which of the following is a product of blast furnace? A. cast iron B. gray iron C. pig iron D. wrought iron Answer: C

Answer: C The cutting angle on a drill for drilling mild steel should be: A. 39 deg. B. 49 deg. C. 59 deg. D. 69 deg.

A product of paddling furnace which contains less than 0.104 carbon, is called A. cast iron B. gray cast iron C. pig iron D. wrought iron

Answer: C

Answer: D

A device used to fix two or more parts. A. clamp B. fastener C. fixtures D. jigs

Which of the following is a property of wrought iron? A. brittle B. can not be forged C. can be easily cast into different shapes D. ductile

Answer: B Answer: D

A piece of stock 8’’ long is 4” diameter on one end and 1” diameter on the other end. The taper per foot is: A. 4” B. 4 -1/2” C. 4 -1/4” D. 4 -1/16”

The type and number of bearings to be used for spindles of machine tool depend on A. type of spindle B. type of machine tool C. load on the ring D. load on the bearing

Answer: B Answer: D A piece of stock 8” long is 3” diameter at ine end and 1 – ½” diameter at the other end. The taper per inch is: A. ½” B. ¼” C. 3/16” D. 5/16”

Which of the following has its angle 30 and is used for dotting after marking the lines on general works? A. center punch B. dot punch C. hollow punch D. prick punch

Answer: C A piece of stock 6” long is 2” diameter at one end and is cut with a taper of ½” to the foot. The diameter of the smaller end will be: A. 1 – ½’ B. 1 – ¾’ C. 1 - ¼’ D. 2”

Answer: D Which of the following has its angle 60 and is used for dotting after marking the lines on general works? A. center punch B. dot punch C. hollow punch D. prick punch

Answer: B If a piston ring is to be made 1/64” larger in diameter per inch diameter of the cylinder which it is to fit, the required diameter for a piston ring to fit an 8” cylinder will be: A. 8 – ¼” B. 8 - 1/8” C. 8 – 3/16” D. 8 – 5/32”

Answer: B Which of the following has its angle 90 and is used to give deep marks for the location of drill? A. center punch B. dot punch C. hollow punch D. prick punch

Answer: B Answer: A When cutting. A drill will “squeal” due to: A. drill being ground improperly B. drill being too hot C. insufficient lubrication D. any of the above

It is used on soft metals and non-metals for making holes. A. center punch B. dot punch C. hollow punch D. prick punch

Answer: D “Center drilling” is the operation of: A. drilling a center in an odd-shaped piece of metal B. drilling and countersinking with one tool C. centering with one tool and drilling with another D. drilling a center in a piece of stock in a drill press

Answer: C

Answer: B

Answer: D

Reason why cast iron selected for the manufacture of surface of surface plate A. it is cheaper B. it is easy for machinery C. it has less wear and tear D. all of the above

The common measuring tools are A. micrometer B. steel rule C. vernier caliper D. all of the above

Which of the following is an unsafe condition in operating a lathe machine? A. operating with safety gloves B. wearing a canvass apron C. wearing denim pants / safety shoes D. wearing safety goggles / hearing aid

Answer: D Answer: B Which of the following is not a kind of mandrel? A. contraction B. expanded C. extended D. taper

The instrument used to remove old packing from packing glands and stuffing boxes are called: A. packing tools B. packing bits C. gland box cleaners D. packing screws

Answer: A Answer: A An act of cutting out a piece of metal at a desired shape and size is known as A. blanking B. broaching C. dinking D. slitting

When working on bearing and checking for high spots, it is customary to apply: A. white lead B. red lead C. dykem blue D. Prussian blue

Answer: A

Answer: D

Safety features that must be placed and maintained at machine, black smith welding and foundry shops called A. safety goggles B. safety notices C. safety notices in markers / boards D. walkway shops

If you wanted to check the face of a pump slide valve or other flat –face valve, you would check for trueness on a: A. flat board B. surface plate C. piece of glass D. bearing plate

Answer: C Answer: B In be A. B. C. D.

cutting tool the cutting end can also generally called back rake end cutting edge nose side rake

Answers: C A machine shop equipment that can flatter horizontally, vertically or angular plane called A. drill machine B. power saw C. shaper machine D. welding machine

To keep a metal clean while soldering, one would use a: A. flax B. torch C. flux D. insulated Answer: C Before splicing electric wires, they should be: A. tinned B. cleaned and tinned C. soldered D. insulated

Answer: C Answer: B

To check the speed of a motor or other rotary machine, one wold A. speed indicator B. micrometer C. tachometer D. A or C

A lathe with multiple cutting stations called: A. engine lathe B. manual lathe C. semi-manual lathe D. turret lathe

Answer: D

Answer: D

It is the best instrument for measuring a thousandth of an inch A. Caliper B. Micrometer C. Pyrometer D. Tachometer

Device used to measure accurately speed called A. dial gage B. dial indicator C. speedometer D. tachometer

Answer: B

Answer: D

What tool will be used in making wood pattern in the foundry shop? A. Sand saw B. Drill machine C. Hammer D. Saw and chisel

A pipe wrench (Stilleon) is designed for use on: A. hexagonal objects B. round objects C. square objects D. flat objects

Answer: D

Answer: B

Machine tool used for laying straight lines on metal surfaces made of sharp tool steel is called A. divider B. hermaphrodite caliper C. plain scriber D. trammel

Pipe is measured by: A. inside diameter B. outside diameter C. thickness of wall D. wire gage Answer: A

Answer: C A lathe machine threading mechanism is called A. anvil B. changed stud gear C. reverse gear and lever D. spindle gear Answer: D Which of the following is not used to resemble the shape of tool bit? A. center cut B. round nose C. square nose D. thread cutting

Tubing is measured by: A. inside diameter B. outside diameter C. thickness of wall D. wire gage Answer: B “Water Hammer” is caused by: A. hitting water pipe with hammer B. too much water in pipe system C. water in steam line D. steam in water line Answer: C Insulation is used on piping to: A. held in heat B. held in cold C. cut down heat losses D. steam in water line

Answer: A Answer: C

It is a machine used for the testing of very thin steel or surface layers. A. Charpy test B. Description test C. Izod test D. Rockwell test

Which tools does not belong to the group? A. adjustable wrench B. feeler gage C. torque wrench D. vice grip Answer: B

Answer: D It is a test for pipe used for coiling in sizes 2 inches. A. bend B. crush C. flange D. flaring Answer: A Milling machine accessories are used to hold milling cutter in the milling machine called: A. milling machine arbors B. milling machine size C. spindle – nose tooling D. vertical milling attachment Answer: A An important accessories of milling machine. A. cutters B. milling machine vise C. ram D. vertical milling attachment Answer: A The machine, which can flatter surface on horizontal, vertical or angular plane. A. drilling machine B. lathe machine C. power saw D. shaper machine Answer: D Which of the following is not part on a lathe machine? A. carriage B.fan C. headstock D. tail stock

The tool used to cut threads in a hole is called a: A. top B. tap C. bit D. reamer Answer: B Hand taps called: A. taper, B. short, C. taper, D. short,

are provided in sets of three plug and end taper and bottom plug and bottom medium and long

Answer: C Which of the following taps should be used to start a thread? A. plug B. short C. bottom D. taper Answer: D When preparing to tap a hole, the size of the drill will be: A. equal to the size of the tap B. larger than the size of the tap C. smaller than the size of the tap D. none of the above Answer: C Pipe taps are: A. the same size from end to end B. not fluted C. tapered D. not hardened Answer: C When preparing to tap a hole for a pipe fitting the size of the drill will be: A. larger than the tap size B. equal to the size of the tap C. smaller than the tap size D. none of the above

Answer: B Answer: A

A machine tool used to out metal parts a lift, medium and large section using a reciprocating hacksaw blade. A. planer B.power saw C. shaper D. tool grinder

Wiping is the process of A. applying flux during welding process B. cleaning the welded surface after the welding operation is over C. connecting load pipes by soldering alloy D. low temperature welding

Answer: B Answer: C A cold chisel is made of A. cast iron B.german silver C. high carbon silver D. high speed steel

Which of the following is not a cut of file? A. smooth B. second cut C. half-round D. bastard

Answer: C Trimming is a process associated with A. electroplating B.forging C. machining of metals D. press work Answer: B A twist drill is specified by A. its diameter and lip angle B. it shank and diameter C. shank, material and diameter D. shank, material and flute size Answer: C The usual value of helix angle of a drill is: A. 30* B. 60* C. 110* D. 120* Answer: A The helix angle on a high-speed steel twist drill for drilling cast iron if of the order of A. 12-22 B. 24-32 C. 35-40 D. 40-45

Answers: C The tool used for cleaning files is called a: A. file cleaner B. file card C. file oilstone D. scraper Answer: B Which of the following is the smallest size drill? A. # 80 B. # 60 C. # 1 D. # 0 Answer: A Which of the following is the largest size drill? A. A B. X C. Z D. XX Answer: C The size of drill is stamped on the: A. point B. shank C. margin D. flute Answer: B

Answer: B

Which of the following safety precautions should be followed when pouring Babbitt? A. operator must wear goggles B. the surface to be babbitted must be free of moisture C. the surface to be babbitted must be clean D. all of the above Answer: D Which of the following safety precaution should be followed when renewing a flange gasket? A. drain the line thoroughly B. isolate the section to be worked on C. tie down isolation valves D. all of the above Answer: D Brazing requires: A. hard solder B. soft solder C. more heat D. A and C

Which of the following is not part of the headstock? A. Anvil B. Back pressure C. Motor D. Spindle Answer: A A machining operation whereby the tool reciprocates and the feed is stationary. A. Planing B. Reaming C. Shaping D. Turning Answer: C The kind of center, which is being attached and meshed to he tailstock spindle, which is also static while the work, is rotating is know as: A. dead center B. focal center C. live center D. work center Answer: A

Answer: D Lead is used in solder because: A. it has a high melting point B. it has a low melting point C. it is cheap D. B and C

A machine tool in which an abrasive wheel is used as a cutting tool to obtain a very smooth finish. A. Broaching machine B. Milling Machine C. Planer D. Tool Grinder

Answer: D

Answer: D

The name of the taper shank used on drills is: A. Miller B. Morse C. Starret D. Stanley

A machine too used principally to machine flat or plane surfaces with a single pointed tool. A. Drill B. Planer C. Power Saw D. Shaper

Answer: B Answer: D The higher the melting point of the solder, the: A. weaker the solder t B. softer the solder t C. stronger the solder t D. harder the solder t

A tool with hardened steel point used for scribing or laying of distances. A. Divider B. Hermaphrodite C. Plain scriber D. Trammel

Answer: C Answer: A

The cylinder of piston type steam engine are counterbored to: A. give a larger head clearance B. prevent piston rings from wearing a groove in the cylinder at the end of the stroke C. give a larger volumetric clearance D. prevent piston rings from slipping on the piston Answer: B When installing packing in a packing box: A. leave one old turn at the bottom of the packing box B. remove one turn and install one new turn of packing C. leave sufficient end clearance on each turn to allow for expansion D. place and cuts directly in line with each other

The operation of enlarging a hole is called A. boring B. counter sinking C. drilling D. reaming Answer: A In A. B. C. D.

up cut milling the work piece is fed against the rotating cutter at an angle of 60* to the cutter at right angle to the cutter in the direction of the cutter

Answer: A Rapping allowance is provided on a patter to take care of A. distortion B. easy withdrawal C. machining D. shrinkage

Answer: C An instrument consisting of a wet – and dry – bulb thermometer (used in air conditioning) is called a: A. hygrometer B. pyrometer C. psychrometer D. A or C Answer: D Sheet A. 12 B. 14 C. 22 D. 16

metal of # 18 gage is heavier than: gage gage gage gage

Answer: C Shims are used to: A. separate fresh – and salt – water lines B. replace fuses C. adjust cylinder liners D. adjust bearing clearances Answer: D Quick return motion is used in a A. drilling machine B. grinder C. lathe D. shaper Answer: D

Answer: B Feeler gage are used for measuring the A. clearance between mating parts B. pitch of screw threads C. radius of curvature D. thickness of plates

Answer: A