Oscilador De Inverter Bd9897fs m231f

1/4

STRUCTURE

Silicon Monolithic Integrated Circuit

NAME OF PRODUCT

DC-AC Inverter Control IC

TYPE

ＢＤ９８９７ＦＳ

FUNCTION

・ ・ ・ ・ ・ ・ ・ ・ ・ ・

36V High voltage process 1ch control with Full-Bridge Lamp current and voltage sense feed back control Sequencing easily achieved with Soft Start Control Short circuit protection with Timer Latch Under Voltage Lock Out Mode-selectable the operating or stand-by mode by stand-by pin Synchronous operating the other BD9897FS IC’s BURST mode controlled by PWM and DC input Output liner Control by external DC voltage

○Absolute Maximum Ratings（Ta = 25℃） Parameter Supply Voltage BST pin SW pin BST-SW voltage difference Operating Temperature Range Storage Temperature Range Maximum Junction Temperature Power Dissipation *

Symbol

Limits

Unit

VCC

36

V

BST

40

V

SW

36

V

BST-SW

7

V

Topr

-40～+85

℃

Tstg

-55～+150

℃

Tjmax

+150

℃

Pd

950*

mW

Pd derate at 7.6mW/℃ for temperature above Ta = 25℃ (When mounted on a PCB 70.0mm×70.0mm×1.6mm)

〇Operating condition Parameter Supply voltage BST voltage BST-SW voltage difference CT oscillation frequency BCT oscillation frequency

Symbol

Limits

Unit

VCC

7.5～30.0

V

BST

4.0～36.0

V

BST-SW

4.0～6.5

V

fCT

60～180

kHz

fBCT

0.05～1.00

kHz

Status of this document The Japanese version of this document is the official specification. Please use the translation version of this document as a reference to expedite understanding of the official version. If

these

are

any

uncertainty

in

translation

version

of

REV. B

this

document,

official

version

takes

priority.

2/4 ○ Electric Characteristics（Ta=25℃，VCC=24V） Parameter （（WHOLE DEVICE）） Operating current

Symbol

Limits TYP.

MIN.

MAX.

Unit

Conditions

Icc1

－

7.2

13

mA

Icc2

－

13.0

30.0

μA

VstH VstL

2.0 -0.3

－ －

VCC 0.8

V V

VuvloH ⊿VCC_Vuvlo Vuvlo2 ⊿Vuvlo

5.7 0.26 2.179 0.074

6.0 0.35 2.25 0.098

6.3 0.43 2.321 0.122

V V V V

VREG IREG

5.68 20.0

5.80 －

5.92 －

V mA

Iact Ineg VOSCH

1.35/(RT*7) Iact×29 1.8

1.5/(RT*6) Iact×35 2.0

1.65/(RT*5) Iact×41 2.2

A A V

fCT=120kHz

OSC Min voltage Soft start current SRT ON resistance （（BOSC BLOCK））

VOSCL

0.35

0.45

0.60

V

fCT=120kHz

ISS RSRT

0.6 －

1.1 100

1.6 200

μA Ω

BOSC Max voltage

VBCTH

1.94

2.00

2.06

V

BOSC Min voltage BOSC constant current

VBCTL

0.40

0.50

0.60

V

fBCT=0.3kHz

IBCT

1.35/BRT

1.5/RT

1.65/RT

A

VBCT=0.2V

BOSC frequency （（FEED BACK BLOCK））

fBCT

291

300

309

Hz

(BRT=33kΩ BCT=0.048μF)

IS threshold voltage 1

VIS①

1.225

1.250

1.275

V

IS threshold voltage 2

VIS②

－

VREFIN

VIS①

V

VVS

1.220

1.250

1.280

V

IIS1 IIS2 IVS VISCOMP① VISCOMP② VREFIN

－ 32 － 0.90 － 0.6

－ 50 － 0.94 VREFIN×0.73 －

0.9 68 0.9 0.98 － 1.6

μA μA μA V V V

VDUTY-OUTH VDUTY-OUTL RDUTY-OUTSink RDUTY-OUTSouce

2.8 － － －

3.1 150 250

3.4 0.5 300 500

V V Ω Ω

RsinkLN RsourceLN RsinkHN RsourceLN MAX DUTY TOFF FOUT

0.75 2.5 1.25 2.5 46.0 100 58.5

1.5 5 2.5 5 48.0 200 60.0

3.0 10 5.0 10 49.5 400 61.5

Ω Ω Ω Ω % ns kHz

V I

1.94 0.40

2.0 0.55

2.06 0.70

V μA

VCOMPH VCOMP2_H VCOMP_L_1 VCOMP_L_2

2.460 2.460 1.225 0.606

2.485 2.485 1.25 0.625

2.510 2.510 1.275 0.644

V V V V

VCT_SYNCH

2.8

3.1

3.4

V

VCT_SYNCL

－

－

0.5

V

RCT_SYNC_SYNC RCT_SYNC_SOURCE VCT_SYNC_IN_H VCT_SINK_IN_L

－ － 2.0 -0.3

150 370 － －

300 740 3.3 0.6

Ω Ω V V

Stand-by current （（STAND BY CONTROL）） Stand-by voltage H Stand-by voltage L （（UVLO BLOCK））） Operating voltage (VCC) Hesteresis width (VCC) Operating voltage (UVLO) Hesteresis width (UVLO) （（REG BLOCK）） REG output voltage REG source current （（OSC BLOCK）） Active edge setting current Negative edge setting current OSC Max voltage

VS threshold voltage IS source current 1 IS source current 2 VS source current IS COMP detect voltage ① IS COMP detect voltage ② VREF input voltage range （（DUTY BLOCK）） High voltage Low voltage DUTY-OUT sink resistance DUTY-OUT source resistance （（OUTPUT BLOCK）） LN output sink resistance LN output source resistance HN output sink resistance HN output source resistance MAX DUTY OFF period Drive output frequency （（TIMER LATCH BLOCK）） Timer Latch setting voltage Timer Latch setting current （（COMP CLOCK）） COMP1 over voltage detect voltage COMP2 over voltage detect voltage COMP2 under voltage detect voltage ① COMP2 under voltage detect voltage ② ((Synchronous Block)) High voltage Low voltage CT_SYNC sink resistance CT_SYNC source resistance High voltage input range Low voltage input range

（This product is not designed to be radiation-resistant.）

REV. B

CT_SYNC_IN = OPEN

System ＯＮ System ＯＦＦ

VCC>7.0V

fBCT=0.3kHz

VREF applying voltage

DUTY=2.2V DUTY=0V IS=0.5V VREFIN≧1.25V VREFIN＜1.25V No effect at VREF＞1.25V

VBST-VSW=5.0V VBST-VSW=5.0V FOUT=60kHz (RT=4.7kΩ CT=235pF)

VSS＞2.2V VSS＞2.2V VSS＞2.2V VSS＜2.2V

3/4

〇Package Dimensions

〇Pin Description

Device Mark

BD9897FS

Lot No.

SSOP-A32 (Unit：mm)

〇Block Diagram

REV. B

PIN No.

PIN NAME

1

PGND

Ground for FET drivers

2

LN2

NMOS FET driver

3

HN2

NMOS FET driver

4

SW2

Lower rail voltage for HN2 output

5

BST2

Boot-Strap input for HN2 output

6

CT_SYNC_IN

CT synchronous signal input pin

7

CT_SYNC_OUT

CT synchronous signal output pin

8

SRT

9

RT

10

CT

11

GND

12

BCT

FUNCTION

External resistor from SRT to RT for adjusting the triangle oscillator External resistor from SRT to RT for adjusting the triangle oscillator External capacitor from CT to GND for adjusting the triangle oscillator GROUND External capacitor from BCT to GND for adjusting the BURST triangle oscillator External resistor from BRT to GND for adjusting the BURST triangle oscillator

13

BRT

14

DUTY

15

DUTY_OUT

16

STB

Stand-by switch

17



External capacitor from to GND for Timer Latch

18

FAIL

COMP2 under voltage protect clock output

19

VREF

Reference voltage input pin for Error amplifier

20

VS

Error amplifier input

21

IS

Error amplifier input

22

FB

Error amplifier output

23

SS

External capacitor from SS to GND for Soft Start Control

24

COMP2

Under, over voltage detect pin

25

COMP1

Over voltage detect pin

26

VCC

Supply voltage input

27

UVLO

External Under Voltage Lock Out

28

REG

Internal regulator output

29

BST1

Boot-Strap input for HN1 output

30

SW1

Lower rail voltage for HN1 output

31

HN1

NMOS FET driver

32

LN1

NMOS FET driver

Control PWM mode and BURST mode BURST signal output pin

4/4

〇NOTE FOR USE １. When deg the external circuit, including adequate margins for variation between external devices and IC. Use adequate margins for steady state and transient characteristics. ２. The circuit functionality is guaranteed within of ambient temperature operation range as long as it is within recommended operating range. The standard electrical characteristic values cannot be guaranteed at other voltages in the operating ranges, however the variation will be small. ３. Mounting failures, such as misdirection or miscounts, may harm the device. ４. A strong electromagnetic field may cause the IC to malfunction. ５. The GND pin should be the location within ±0.3V compared with the PGND pin. ６. BD9897FS incorporate a built-in thermal shutdown circuit (TSD circuit). The thermal shutdown circuit (TSD circuit) is designed only to shut the IC off to prevent runaway thermal operation. It is not designed to protect the IC or guarantee its operation of the thermal shutdown circuit is assumed. ７. Absolute maximum ratings are those values that, if exceeded, may cause the life of a device to become significantly shortened. Moreover, the exact failure mode caused by short or open is not defined. Physical countermeasures, such as a fuse, need to be considered when using a device beyond its maximum ratings. ８. About the external FET, the parasitic Capacitor may cause the gate voltage to change, when the drain voltage is switching. Make sure to leave adequate margin for this IC variation. ９. On operating Slow Start Control (SS is less than 2.2V), It does not operate Timer Latch. １０. By STB voltage, BD9897FS are changed to 2 states. Therefore, do not input STB pin voltage between one state and the other state (0.8～2.0V). １１. The pin connected a connector need to connect to the resistor for electrical surge destruction. This IC is a monolithic IC which (as shown is Fig-1) has P+ substrate and between the various pins. A P-N junction is formed from this P layer of each pin. For example, the relation between each potential is as follows, ○(When GND > PinB and GND > PinA, the P-N junction operates as a parasitic diode.) ○(When PinB > GND > PinA, the P-N junction operates as a parasitic transistor.) Parasitic diodes can occur inevitably in the structure of the IC. The operation of parasitic diodes can result in mutual interference among circuits as well as operation faults and physical damage. Accordingly you must not use methods by which parasitic diodes operate, such as applying a voltage that is lower than the GND (P substrate) voltage to an input pin. １２．This IC is a monolithic IC which (as shown is Fig-1)has P+ substrate and between the various pins. A P-N junction is formed from this P layer of each pin. For example, the relation between each potential is as follows, ○(When GND > PinB and GND > PinA, the P-N junction operates as a parasitic diode.) ○(When PinB > GND > PinA, the P-N junction operates as a parasitic transistor.) Parasitic diodes can occur inevitably in the structure of the IC. The operation of parasitic diodes can result in mutual interference among circuits as well as operation faults and physical damage. Accordingly you must not use methods by which parasitic diodes operate, such as applying a voltage that is lower than the GND (P substrate) voltage to an input pin. Transistor (NPN)

Resistance (PinA)

(PinB)

B E

C

Ｃ

GND P

P＋

N P＋

N

Ｎ

N

Ｎ

P substrate GND Parasitic diode

N

P substrate GND Parasitic diode (PinB)

(PinA) B

CＣ

Ｂ

EＥ

Parasitic diode

GND GND

Other adjacent components

Parasitic diode

Fig-1 Simplified structure of a Bipolar IC

REV. B

Notice

Notes No copying or reproduction of this document, in part or in whole, is permitted without the consent of ROHM Co.,Ltd. The content specified herein is subject to change for improvement without notice. The content specified herein is for the purpose of introducing ROHM's products (hereinafter "Products"). If you wish to use any such Product, please be sure to refer to the specifications, which can be obtained from ROHM upon request. Examples of application circuits, circuit constants and any other information contained herein illustrate the standard usage and operations of the Products. The peripheral conditions must be taken into when deg circuits for mass production. Great care was taken in ensuring the accuracy of the information specified in this document. However, should you incur any damage arising from any inaccuracy or misprint of such information, ROHM shall bear no responsibility for such damage. The technical information specified herein is intended only to show the typical functions of and examples of application circuits for the Products. ROHM does not grant you, explicitly or implicitly, any license to use or exercise intellectual property or other rights held by ROHM and other parties. ROHM shall bear no responsibility whatsoever for any dispute arising from the use of such technical information. The Products specified in this document are intended to be used with general-use electronic equipment or devices (such as audio visual equipment, office-automation equipment, communication devices, electronic appliances and amusement devices). The Products specified in this document are not designed to be radiation tolerant. While ROHM always makes efforts to enhance the quality and reliability of its Products, a Product may fail or malfunction for a variety of reasons. Please be sure to implement in your equipment using the Products safety measures to guard against the possibility of physical injury, fire or any other damage caused in the event of the failure of any Product, such as derating, redundancy, fire control and fail-safe designs. ROHM shall bear no responsibility whatsoever for your use of any Product outside of the prescribed scope or not in accordance with the instruction manual. The Products are not designed or manufactured to be used with any equipment, device or system which requires an extremely high level of reliability the failure or malfunction of which may result in a direct threat to human life or create a risk of human injury (such as a medical instrument, transportation equipment, aerospace machinery, nuclear-reactor controller, fuel-controller or other safety device). ROHM shall bear no responsibility in any way for use of any of the Products for the above special purposes. If a Product is intended to be used for any such special purpose, please a ROHM sales representative before purchasing. If you intend to export or ship overseas any Product or technology specified herein that may be controlled under the Foreign Exchange and the Foreign Trade Law, you will be required to obtain a license or permit under the Law.

Thank you for your accessing to ROHM product informations. More detail product informations and catalogs are available, please us.

ROHM Customer System http://www.rohm.com//

www.rohm.com © 2009 ROHM Co., Ltd. All rights reserved.

R0039A