Bts Commissioning Alcatel Lucent 1h4g5d

Switch OFF the BTS cabinet and disconnect Abis connectors from DDF before offline start

Disconnect the Abis connector from The DDF

Switch ON the BTS cabinet breakers and connect the Laptop with BTS

Name “COMMTE”

“COMMTE”

Communication Port setting

OR

After connecting this window will be appear

Go to Configuration-> BTS-SW -> to BTS software

After BTSSW this window will appear

Go to offline Files and select First File of Master File.

Go to offline Files and select First File of DDL file.

Click ok to start ing SW

BTS software starts to .

All these Files are ed

Go to Configuration BTS commissioning

Click start commissioning

Edit Qmux Address

Edit sector Mapping

Check All Twin TRE’s.

Click End Commissioning

Click << arrow to move selected modules to available modules

All modules Shifted to update modules.

Click No to end

Reconnect the Abis connector at DDF by ing the TX/RX cables properly

Give Hard Reset to BTS cabinet as the OML has established to put the site on ing.

OFF Line Commissioning Completed Successfully.

BTS ON-Line commissioning Procedure using B10 Go to configuration>> Hardware setting>>Begin HW modification

Go to configuration> BTS commissioning

Go to start commissioning> Edit Q1 Address, Edit Sector Mapping and Twin TRA setting as in offline.

Go to configuration> Hardware setting>“End Modification” to end online commissioning

Online commissioning steps  Connect the Abis connector at DDF by ing Tx/Rx cable properly.  OML will be established after primary Abis has

  

 

connected to DDF. Give hard reset to BTS after OML has established. Put site on ing from OMC. O&M will be established as ing completes. Connect Laptop to BTS MMI port. Go to configuration>Hardware setting>Begin Hardware modification.

Online commissioning steps  Go to configuration>BTS commissioning>start       

commissioning. Edit Qmux Address Edit sector mapping Check all Twin TRA setting. Click end commissioning and shift all modules from selected modules to available modules. Go to configuration>Hardware setting>End Hardware modification. Click “yes” when an automatically hardware modification window appears. Hw Audit will be run and all Hardware will be shown after sometime.

ON Line Commissioning Completed Successfully.

Software components combiner

Fan Unit

Hardware Shown in software window Tre’s clock Alarm card

Alarms window

Transceivers Shown in window

Transceivers Types  Four type of Transceivers in Alcatel Equipment  TRAGE>Gsm Single TRE  TRADE>Dcs single TRE  TGT09>Gsm Twin TRE  TGT18>DCS Twin TRE  TAGHE>High power TRE

VSWR Shown in window

Sectors Shown In window

Station units

BSC SBLs (security block levels) BTS OM & Sectors.Sec RSLs can be unlock from local Terminal.

Troubleshooting  If a TRE or combiner is in “Not Operational” or “FOS” state then       

disable it then initialize it by using “init” command. If TRE or combiner can not operational by doing above command then remove it by using the following method. Go to configuration>>Hardware setting>>Begin HW modification. Go to Configuration>>Hardware setting>>Remove. Remove the Hardware from BTS. Window will be appear of Hardware removal, select the module to remove. Go to Configuration>>Hardware setting>>End Modification. Click ”yes” when configuration changes window appears.

Hardware Removal Method Step:1

Hardware Removal Step:2

Hardware Removal Step:3

Troubleshooting cont..  When a module goes in “FOS” state then it must be disable by

using ”disable” command before initializing it by using “init” command otherwise it will not goes to operational state.  When a module is in “Not Operational” state with color white then it means it has not got it’s RSL number still. Reload BTS data by going to “configuration>Reload Bts data” or using a method of “Begin Hardware then End Hardware” as discussed earlier. It will take some time to become operational.  When a module is in “MSD” or “MSA” state then it will not get any command because its maintenance has seized for a while.  When TRE RSL has locked then then its RSL will not be stable, so unlock the TRE from OMC.

Troubleshooting cont..  Sometime there is some faulty hardware in Bts that’s why other

sectors or TRE’s can effect and can not work properly. Due to these faulty hardware other sectors or TRE’s can be down so simply remove this hardware. By this method other hardware become in operational state.  Some time “SUMA” can not work properly that’s why whole Bts effects so change the slot of “SUMA” and give hard reset to Bts.  If modules in a shelf can not powers up then check it’s power cable at the back ports of Bts or check it “RI” cable. Also check the power switch for the concern shelf.  If a “EACB” card is Not operational or “FIT” state then initialize it from software. If it again goes in “FIT” state then Alarm card is faulty.

Troubleshooting cont..  Some time Primary Abis is stable by showing LED on Suma card

but OML can not become stable, It means that Abis LED is fake. So check the Tx/Rx cable from both Bts end and microwave end and make sure that it is correctly connected. Also check Tx/Rx patching on DDF by using LED. Make sure that LED blinks on every pair on DDF. Also check the BNC and Abis connectors. Abis cable which is connected from Suma card to Bts board can be faulty so also it.  If a TRE or combiner can not operational than change its slot then it.  Vswr issues can be resolved by checking connectors from Bts end and feeder end.  The last option for Alcatel equipment to become operational is the “Hard reset of Bts”.

External Alarms of MBO2

ALCATEL GLOSSARY AN

A Antenna Network B

BCB BSII BSS BTS BTSW

BTS Control Bus Base Station Controller Base Station Subsystem Base Station Transceiver BTS-Terminal for Windows C

CCF CDM CLEI CLLK F CRC CU

Cabinet Cooling Fan Configuration Data Message Common Language Equipment Clock Link Configuration Parameter File Cyclic Redundancy Check Carrier Unit

ALCATEL GLOSSARY D DC DMA EQU FIA FIM FIT FLT FOS ICS IT LDA LRA MI MSA MSD

Direct Current Deferred Maintenance Alarm E Equipped F Format Identifier for Application part of RI Format Identifier Manufacturing Faulty In Traffic Faulty Faulty Out of Service Item Change Status In Traffic L Local Defence Action Local Recovery Action M Maintenance Information MSD Auto Maintenance Seized

ALCATEL GLOSSARY N NEQ NOP O&M OMU OMUA OMUB OP OPR PADD PMA

Not Equipped Not Operational O Operation and Maintenance Operation and Maintenance Unit OMU A RIT OMU B RIT Operational Operator P Physical Address Prompt Maintenance

ALCATEL GLOSSARY RA RF RFH Hopping ) RI RIT RX RTC SBL SCFE SOS SUM SUMP SW

R Radio Access Radio Frequency Radio Frequency Hopping ( also known as : Synthesizer Remote Inventory Replaceable Item Receiver or receive ..... Remote Tunable Combiner S Security Block Level Station Unit Control Function Entity RIT System Out of Service Station Unit Module SUM PCM RIT Software

ALCATEL GLOSSARY SBL SCFE SOS SUM SUMP SW TLV TRE TS TX VPMA VSWR

S Security Block Level Station Unit Control Function Entity RIT System Out of Service Station Unit Module SUM PCM RIT Software T Tag, Length, Value Transceiver Module (combined Transmitter / Receiver functionality for base band and RF signals) Timeslot Transmitter or transmit . V Very Prompt Maintenance Alarm Voltage Standing Wave Ratio

ALCATEL GLOSSARY WBC WTC XBCB XCLK XIOB

W Wide Band Combiner Wait Traffic Clear X External BCB External Clock External Input Output Board