As400 Daily Commands 402a7

AS/400 System Functions (Daily checking) WRKSYSSTS - Work with System Status (Wait at least 5 mins before using any of the values, Pressing the refresh key, PF5) a. % U used. b. % System ASP used, system pool size. Check not over 80%. Would require additional memory. c. Observe page faulting -Fault rate non-DB machine Pool The rate, page faults per second, of non-database page faults against pages other than those designated as database pages. A page fault is a program notification that occurs when a page that is marked as not in main storage is referred to by an active program. d. Active to Wait. (F11). The rate, transitions per minute, of transitions of jobs from an active condition to a waiting condition. (Adjust MAX Active so that 10% of Active->Wait is Wait->Ineligible) DSPMSG MSGQ(*SYSOPR) - Messages from the system operator message queue. Check the "Messages needing a reply" WRKACTJOB - Work with Active Jobs (To check the jobs using the largest amount of U, press the F16" key, while the cursor is over the U heading). (All jobs on the AS/400 run in memory. To determine which pools your jobs are running in use WRKACTJOB) (Press "F11", Elapsed data, to display the pool number) WRKUSRJOB - Work with Jobs WRKUSRJOB (*ALL) STATUS(*ACTIVE) JOBTYPE(*INTERACT) ASTLVL(*BASIC) (Ability to check what jobs are running and, as shown above, to send messages to all interactive s "F10=Send message to all") WRKDSKSTS - Work with Disk Status Check the estimated percentage of time the disk unit is being used during the elapsed time. This estimate is based on the number of I/O requests, the amount of data transferred, and the performance characteristics of the type of disk unit. WRKJOBSCDE - Work with Job Schedule Entries Check the last submission date and time.

WRKSBS - Which subsystems are active. (What types of jobs in each subsystem and how many. Press "F11", to display the number of jobs in each subsystem.) Note: DSPSYSVAL QCTLSBSD - QCTL (Controlling subsystem)

Ask your questions about AS/400 at ITKnowledgeExchange.com DSPMSG

Displays messages in queue

DSPMSGD

Displays description of messages, ie F messages

WRKMSGF QFMSG

Displays contents of MONMSG file

WRKUSRPRF -

Can work with specified 's profile

WRKSBMJOB *JOB

Displays my jobs for the current session

WRKACTJOB

Displays all active jobs

WRKUSRJOB

Displays list of my jobs to work with

WRKOBJ

Work with an object. Use *ALLUSR in qualified name to skip Q libraries

WRKSPLF

Displays spool files

WRKOUTQ

Displays in specified OUTQ

DISPLIB

Displays contents of specified library

EDTLIBL

Allows addition and deletion of libraries to and from list

ADDLIBLE Library Name

Add library to current list

STRPDM

Start PDM

STRDBG

Start Debug

ADDBKP

Add a break point and variables to monitor in debug

RMVBKP

Remove a break point in debug

ENDDBG

End Debug

STRDBU

Start DBU (Database Utility) Look at and make changes to the database

DBU Qualified Name

Runs DBU without the above command. ADDLIBLE DBU41 *LAST before using

STRDFU

Start DFU (Data File Utility) Many of the same functions of DBU

DSPFFD

Displays file field descriptions

DSPFD

Displays file description for specified file

DSPPFM

Displays member of a physical file

DSPDBF

Displays contents of database file. Must add TAATOOL to library list before using this command

DSPPGMREF

Display the files used in a program and which libraries the program was compiled over

PRTRNG

Will allow printing a range of pages from a member in the specified OUTQ. Must add PRTRNG to library list before using this command

OUTQ(PRINTER)

Mark object in spool file with 2 for change. Type this on the command line.

WRKJOBSCDE

Look at scheduled jobs

RUNQRY QRYFILE(LIB/FILE)

Run query on a file with no parameters

DSPDBR LIB/FILE

Shows logicals related to a physical file

Miscellaneous: F4 on a command line will take you to the Major Commands Menu F9 on a command line will retrieve prior commands

F16 Displays Defined Options To compile a program without generating a new source object enter 14 for compile then F4. Press F10 for additional parameters. Under source listing options put *NOGEN To end a job without creating a log. Enter the 4 and press F4, How to end *IMMED, Maximum log entries 0