Acer Aspire M1100 6o25u
This document was ed by and they confirmed that they have the permission to share it. If you are author or own the copyright of this book, please report to us by using this report form. Report 2z6p3t
Overview 5o1f4z
& View Acer Aspire M1100 as PDF for free.
More details 6z3438
- Words: 20,858
- Pages: 96
Angora AM50/AM30/AM10
Service Guide
Service guide files and updates are available on the AIPG/CSD web; for more information, please refer to http://csd.acer.com.tw
PRINTED IN TAIWAN
ed from www.Manualslib.com manuals search engine
Revision History Please refer to the table below for the updates made on Angora AM50, AM30, and AM10 service guide. Date
ed from www.Manualslib.com manuals search engine
Chapter
Updates
Copyright Copyright © 2007 by Acer Incorporated. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of Acer Incorporated.
Disclaimer The information in this guide is subject to change without notice. Acer Incorporated makes no representations or warranties, either expressed or implied, with respect to the contents hereof and specifically disclaims any warranties of merchantability or fitness for any particular purpose. Any Acer Incorporated software described in this manual is sold or licensed "as is". Should the programs prove defective following their purchase, the buyer (and not Acer Incorporated, its distributor, or its dealer) assumes the entire cost of all necessary servicing, repair, and any incidental or consequential damages resulting from any defect in the software.
Acer is a ed trademark of Acer Corporation. Intel is a ed trademark of Intel Corporation. Pentium 4 and Celeron are trademarks of Intel Corporation. Other brand and product names are trademarks and/or ed trademarks of their respective holders.
ed from www.Manualslib.com manuals search engine
Conventions The following conventions are used in this manual: SCREEN MESSAGES
Denotes actual messages that appear on screen.
NOTE
Gives bits and pieces of additional information related to the current topic.
WARNING
Alerts you to any damage that might result from doing or not doing specific actions.
CAUTION
Gives precautionary measures to avoid possible hardware or software problems.
IMPORTANT
Reminds you to do specific actions relevant to the accomplishment of procedures.
ed from www.Manualslib.com manuals search engine
Preface Before using this information and the product it s, please read the following general information. 1. This Service Guide provides you with all technical information relating to the BASIC CONFIGURATION decided for Acer's "global" product offering. To better fit local market requirements and enhance product competitiveness, your regional office MAY have decided to extend the functionality of a machine (e.g. add-on card, modem, or extra memory capability). These LOCALIZED FEATURES will NOT be covered in this generic service guide. In such cases, please your regional offices or the responsible personnel/channel to provide you with further technical details. 2. Please note WHEN ORDERING FRU PARTS, that you should check the most up-to-date information available on your regional web or channel. If, for whatever reason, a part number change is made, it will not be noted in the printed Service Guide. For ACER-AUTHORIZED SERVICE PROVIDERS, your Acer office may have a DIFFERENT part number code to those given in the FRU list of this printed Service Guide. You MUST use the list provided by your regional Acer office to order FRU parts for repair and service of customer machines.
ed from www.Manualslib.com manuals search engine
ed from www.Manualslib.com manuals search engine
Table of Contents System Specification
1
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Processor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 System Chipset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Onboard Graphics Solution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 HDMI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 PCI Express/PCI Slots . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Floppy Disk Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 SATA Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 LAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 USB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 1394a . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Buzzer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Front I/O Header . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 CIR & IR Blaster . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Onboard Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 Angora AM50 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 Front . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 Rear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 Angora AM30 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 Front . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 Rear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 Angora AM10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 Front . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 Rear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10 Acer Empowering Technology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11 Empowering Technology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11 Acer eRecovery Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11 Acer eDataSecurity Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12 Acer ePerformance Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14 Acer eRecovery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15 Create Backup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15 Restore from Backup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15 Create Factory Default Image CD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15 Re-install Bundled Software without CD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15 Change . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16 Acer Disc-to-Disc Recovery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17 Restore without a Recovery CD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17 Multilingual Operating System Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17 Hardware Specification and Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18 Processor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18 System Main Chipset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18 North Bridge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18 South Bridge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19 Wake-up Event Specification (Default Setting in BIOS) . . . . . . . . . . . . . . . . . . .19 Front LED States . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20 System Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20 Super I/O . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
i ed from www.Manualslib.com manuals search engine
USB Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20 Audio Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21 1394 Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21 Hardware Monitor Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21 BIOS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22 BIOS Hotkey List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22 Environment Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22 Power Management Function (AI Function) . . . . . . . . . . . . . . . . . . . . . . .23 Device Standby Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23 Global Standby Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23 Suspend Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23 AI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
Setup Utility
25
About the Setup Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25 Control Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25 Entering the Setup Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26 Product Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27 Standard CMOS Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28 Date and Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28 SATA Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28 Drive A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28 Halt On . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28 Base Memory, Extended Memory, and Total Memory . . . . . . . . . . . . . . . . . . . .28 Advanced BIOS Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29 Virus Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29 U Internal Cache/External Cache . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29 Quick Power On Self Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30 First / Second / Third Boot Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30 Boot Other Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30 Boot Up Floppy Seek . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30 Boot Up NumLock Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30 Gate A20 Option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30 Typematic Rate Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30 Security Option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30 APIC Mode 30 MPS Version Control For OS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30 OS Select for DRAM > 64 MB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30 HDD S.M.A.R.T Capability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31 Silent Boot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31 Small Logo (EPA) Show . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31 Configuration Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31 Bootblock Write Protect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31 Hard Disk Boot Priority . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32 Advanced Chipset Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33 UMA Frame Buffer Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33 Memory Hole . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33 System BIOS Cacheable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33 Integrated Peripherals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34 South OnChip IDE Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34 South OnChip PCI Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34 Super IO Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34 Init Display First . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34 South OnChip IDE Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35 IDE DMA Transfer Access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35 ii ed from www.Manualslib.com manuals search engine
OnChip IDE Channel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35 IDE Primary/Secondary Master/Slave PIO . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35 IDE Primary/Secondary Master/Slave UltrA . . . . . . . . . . . . . . . . . . . . . . . .35 IDE HDD Block Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35 South OnChip PCI Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36 ATI Azalia Audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36 ATI SATA Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36 ATI SATA Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36 USB EHCI Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36 OnChip USB Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37 OnChip USB KBC Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37 USB Mouse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37 Onboard LAN Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37 Onboard Lan Boot ROM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37 Onboard 1394 Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37 Super IO Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38 Onboard FDC Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38 Onboard Serial Port 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38 Onboard Serial Port 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38 UART Mode Select . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38 UR2 Duplex Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38 Onboard Parallel Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39 Parallel Port Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39 E Mode Use DMA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39 Power Management Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40 AI Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40 AI Suspend Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40 CS2 Disable/Enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41 Power Management Option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41 Video Off Option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41 Video Off Method . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41 Soft-Off by PWRBTN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41 Power On By PCI Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41 USB Wakeup From S1/S2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41 USB Wakeup From S4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41 PS2 KB/MS Wakeup From S1/S2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41 Wakeup By LAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41 HPET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41 PWRON After PWR-Fail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41 RTC Alarm Resume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42 PnP/PCI Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43 Reset Configuration Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43 Resources Controlled By . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43 PCI/VGA Palette Snoop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43 Assign IRQ For VGA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43 Assign IRQ for USB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44 PCI Latency Timer (CLK) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44 Maximum Payload Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44 PC Health Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45 U Shut Down Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45 Frequency & Voltage Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47 Spread Spectrum . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47 SB600 Spread Spectrum . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47 Load Optimized Defaults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48 Set Supervisor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49 iii ed from www.Manualslib.com manuals search engine
Enter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49 Save and Exit Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50 Exit without Saving . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51
Machine Disassembly and Replacement
53
General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53 Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53 Angora AM50/30/10 Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54 Disassembly Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54 Reassembly Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61
Troubleshooting
69
Jumper and Connector Information
71
Introduction to Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71 Main Board Placement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71 Connectors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .73 Jumpers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .77
FRU (Field Replaceable Unit) List
83
Angora AM50 Exploded Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .84 Angora AM30 Exploded Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .85 Angora AM10 Exploded Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .86
iv ed from www.Manualslib.com manuals search engine
Chapter 1
System Specification Overview Size •
240x240mm (9.6"x9.6") 4 Layers
Processor •
Socket type: AMD AM2 socket
•
Socket quantity: one
•
Processor type: Sempron-D, Athlon64, Athlon64+
System Chipset •
North bridge: ATI RS690
•
South bridge: ATI SB600
•
Super I/O: ITE8718F with Hardware monitor
Memory •
Dual Channel DDR2 667/533/400,Unbuffered DIMM
•
4 DDRII DIMM (8 GB Maximum capacity)
Onboard Graphics Solution •
ATI RS690 on-die graphic solution (ATI Radeon® X700-based graphic core) •
ATI AVIVO technology
•
Multiple display features
•
One D-Sub VGA port on the rear side
•
One HDMI port on the rear side (A14)
•
SDVO interface which s hot plug detection
HDMI •
With HD solution
•
Meets HDMI 1.2a specification
PCI Express/PCI Slots •
One PCI Express x16 slot
•
One PCI Express x1 slot
•
Two PCI slots
Floppy Disk Drive •
One slot, 1.44MB/3 mode 3.5” devices
SATA Interface •
Two separate controllers with integrated SATA 2 (Gen1 and Gen2) PHYs
•
Each controller s two drives in master mode for a total of four
Chapter 1 ed from www.Manualslib.com manuals search engine
1
•
Compliant with ATA/ATAPI-7 Volume 3 Serial ATA standards
•
High speed, low voltage, low pin count
•
Each controller s dual channel SATA 2
•
3.0 Gb/s per direction per channel
•
s power-down capabilities
Audio •
Realtek ALC888-GR, colay with ALC883
LAN •
Marvell 88E8056, Gb PHY featuring: •
10/100/1000BASE-T IEEE 802.3 compliant
•
Two-Wire Serial Interface (TWSI) for VPD
•
2.5GHz Signaling,x1 link width, width strapped on reset
•
of up to eight outstanding NP requests as a master
USB •
X10 USB2.0/1.1(Rear 4 ports, Front 6ports)
1394a •
1394 header x 1 and Back I/O *1 (TSB43AB23PDTG4 2-port)
Buzzer •
One onboard buzzer
Front I/O Header
CIR & IR Blaster •
Compliant to ITE’s pin definition to CIR & IR blaster function for Vista home SKU
•
Power-up feature
Onboard Connectors •
Rear I/O connectors: •
VGA port
•
Dual stack USB ports with 1394 connector
2 ed from www.Manualslib.com manuals search engine
Chapter 1
•
•
Dual Stack USB ports with RJ-45 connector
•
Vertical Audio connector with 6 JACKS
•
DVI-I port
•
HDMI port
•
PS2 port
•
Print port
Onboard connectors: •
One U socket
•
Four DDR2 memory sockets
•
One PCI Express x16 slot
•
One PCI Express x1 slot
•
Two PCI slots
•
One FDD slot
•
One PATA slot
•
Four SATAII IDE connectors
•
Three 2*5 pin USB headers, compliant to Intel FPIO standard specification
•
One 2*5 pin front audio header, compliant to Intel FPIO standard specification
•
One 2*5 pin serial port connector
•
One 1*4 pin AUX-In connector
•
One 4-pin U fan connector
•
One 3-pin system fan connector with linear circuit
•
One 24-pin + 4-pin ATX interface PS3/PS2 SPS connector
•
One 2*7 pin front I/O header
•
One 2*5 pin 1394 header
Chapter 1 ed from www.Manualslib.com manuals search engine
3
Block Diagram
4 ed from www.Manualslib.com manuals search engine
Chapter 1
Angora AM50 Front
#
Chapter 1 ed from www.Manualslib.com manuals search engine
Description
1
ODD Door
2
Slide Door
3
LAN LED
4
HDD LED
5
Power Button
6
USB Port
7
MIC Phone
8
Speaker Out
5
Rear
#
Description
#
Description
1
6 audio jacks (7.1 HD audio jack)
8
PS/2 Keyboard
2
LAN Port
9
PS/2 Mouse
3
USB Ports
10
Power Cable Port
4
1394 Port
11
SPDIF Bracket
5
CRT/LCD Port
12
SPDIF Port
6
Parallel Port
13
Recovery Switch Holder
7
HDMI Port
14
Lock Handle
6 ed from www.Manualslib.com manuals search engine
Chapter 1
Angora AM30 Front
#
Chapter 1 ed from www.Manualslib.com manuals search engine
Description
1
Optical Device
2
3.5” Device
3
LAN LED
4
HDD LED
5
Power Button
6
USB Port
7
MIC Phone
8
Speaker Out
7
Rear
#
Description
#
Description
1
6 audio jacks (7.1 HD audio jack)
8
PS/2 Keyboard
2
LAN Port
9
PS/2 Mouse
3
USB Ports
10
Power Cable Port
4
1394 Port
11
SPDIF Bracket
5
CRT/LCD Port
12
SPDIF Port
6
Parallel Port
13
Recovery Switch Holder
7
HDMI Port
14
Lock Handle
8 ed from www.Manualslib.com manuals search engine
Chapter 1
Angora AM10 Front
#
Chapter 1 ed from www.Manualslib.com manuals search engine
Description 1
Optical Device
2
3.5” Device
3
Power Button
4
HDD LED
5
LAN LED
6
Speaker Out
7
MIC Phone
8
USB Port
9
Rear
#
Description
#
Description
1
6 audio jacks (7.1 HD audio jack)
8
PS/2 Keyboard
2
LAN Port
9
PS/2 Mouse
3
USB Ports
10
Power Cable Port
4
1394 Port
11
SPDIF Bracket
5
CRT/LCD Port
12
SPDIF Port
6
Parallel Port
13
Recovery Switch Holder
7
HDMI Port
14
Lock Handle
10 ed from www.Manualslib.com manuals search engine
Chapter 1
Acer Empowering Technology Acer’s innovative Empowering Technology makes it easy for you to access frequently used functions and manage your new Acer notebook. It features the following handy utilities: •
Acer eRecovery Management backs up and recovers data flexibly, reliably and completely.
•
Acer eDataSecurity Management protects data with s and advanced encryption algorithms.
•
Acer ePerformance Management improves system performance by optimizing disk space, memory and registry settings.
For more information, press the key to launch the Empowering Technology menu, then click on the appropriate utility and select the Help or Tutorial function.
Empowering Technology Before using Acer eRecovery Management, you must initialize the Empowering Technology . Right click on the Empowering Technology toolbar and select Setup to do so. If you do not initialize the Empowering Technology , you will be prompted to do so when running Acer eRecovery Management for the first time.
Acer eRecovery Management Acer eRecovery Management is a powerful utility that does away with the need for recovery disks provided by the manufacturer. The Acer eRecovery Management utility s Microsoft Windows XP Home Service Pack 2, Microsoft Windows XP Media Center Edition Wallop 2, Microsoft Windows Vista Home Basic, , Business, and Ultimate. The Acer eRecovery Management utility occupies space in a hidden partition on your system’s HDD. -created backups are stored on D:\ drive. Acer eRecovery Management provides you with: •
protection
•
Recovery of applications and drivers
•
Image/data backup:
•
•
Back up to HDD (set recovery point)
•
Back up to CD/DVD
Image/data recovery tools •
Recovery from a hidden partition (factory defaults)
•
Recovery from the HDD (most recent -defined recovery point)
•
Recovery from CD/DVD
Chapter 1 ed from www.Manualslib.com manuals search engine
11
For more information, please refer to Acer eRecovery Management. Note: If your computer does not come with a Recovery CD or System CD, please use Acer eRecovery Management’s System backup to optical disk feature to burn a backup image to CD or DVD. To ensure the best results when you recover a system by using a CD or Acer eRecovery Management, detach all peripherals (except the external Acer ODD, if your computer has one), including your Acer ezDock.
Acer eDataSecurity Management Acer eDataSecurity Management is a handy file encryption utility that protects your files from being accessed by unauthorized persons. It is conveniently integrated with Windows explorer as a shell extension for quick and easy data encryption/decryption and also s on-the-fly file encryption for MSN Messenger and Microsoft Outlook. Note: The Acer eDataSecurity Management setup wizard will prompt you for a supervisor and default encryption. This encryption will be used to encrypt files by default, or you can choose to enter your won file-specific when encrypting a file. Note: The used to encrypt a file is the unique key that the system needs to decrypt it. If you lose the , the supervisor is the only other key capable of decrypting the file. If you lose both s, there will be no way to decrypt your encrypted file. Be sure to safeguard all related s!
12 ed from www.Manualslib.com manuals search engine
Chapter 1
Chapter 1 ed from www.Manualslib.com manuals search engine
13
Acer ePerformance Management Acer ePerformance Management is a system optimization tool that boosts the performance of your Acer notebook. It provides and expresses optimization method to release unused memory and disk space quickly. The can also enable advanced options for full control over the following option: •
Memory optimization: to releases unused memory and check usage
•
Disk optimization: to remove unneeded items and files
•
Speed optimization: to improve the usability and performance of your Windows XP system
For more information, please refer to Acer eRecovery Management. Note: If your computer does not come with a Recovery CD or System CD, please use Acer eRecovery Management’s System backup to optical disk feature to burn a backup image to CD or DVD. To ensure the best results when recovering your system using a CD or Acer eRecovery Management, detach all peripherals (except the external Acer ODD, if your computer has one), including your Acer ezDock.
14 ed from www.Manualslib.com manuals search engine
Chapter 1
Acer eRecovery Acer eRecovery is a tool to quickly backup and restore the system. s can create and save a backup of the current system configuration to hard drive, CD, or DVD. Acer eRecovery consists of the following functions: 1. Create backup 2. Restore from backup 3. Create factory default image CD 4. Re-install bundled software without CD 5. Change Acer eRecovery
Create Backup s can create and save backup images to hard drive, CD, or DVD. Please follow the steps below to create backup. 1. Boot to Windows XP. 2. Press
+
to open the Acer eRecovery utility. 3. Enter the to proceed. The default is six zeros. 4. In the Acer eRecovery window, select Recovery settings and click Next. 5. In the Recovery settings window, select Backup snapshot image and click Next. 6. Select the backup method: •
Use Backup to HDD to store the backup disc image on drive D:\
•
Backup to optical device to store the backup disc image on CD or DVD. This option is only available on systems that include an optical disc burner.
7. After choosing the backup method, click Next. Then follow the instruction on the screen to complete the process.
Restore from Backup s can restore backup previously created (as stated in the Create Backup section) from hard drive, CD, or DVD. Please follow the steps below to restore from backup. 1. Boot to Windows XP. 2. Press
+
to open the Acer eRecovery utility. 3. Enter the to proceed. The default is six zeros. 4. In the Acer eRecovery window, select Recovery actions and click Next. 5. Select the desired restore action and follow the instructions on screen to complete the restore process.
Create Factory Default Image CD When the System CD and Recovery CD are not available, you can create them by using this feature. Please follow the steps below to create factory default image CD. 1. Boot to Windows XP. 2. Press
+
to open the Acer eRecovery utility. 3. Enter the to proceed. The default is six zeros. 4. In the Acer eRecovery window, select Recovery settings and click Next. 5. In the Recovery settings window, select Burn image to disc and click Next. 6. In the Burn image to disc image, select Factory default image and click Next. 7. Follow the instruction s on screen to complete the process.
Re-install Bundled Software without CD Acer eRecovery stores pre-loaded software internally for easy driver and application re-installation. 1. Boot Windows XP. 2. Press
+
to open the Acer eRecovery Utility. Chapter 1 ed from www.Manualslib.com manuals search engine
15
3. Enter the to proceed. The default is six zeros. 4. In the Acer eRecovery window, select Recovery actions and Next. 5. In the Recovery settings window, select Re-install applications / drivers and click Next. 6. Select the desired driver / application and follow the instructions on screen to re-install. After the first launch, Acer eRecovery prepared all the needed software and may take few seconds to bring up the software content window.
Change Acer eRecovery and Acer disc-to-disc recovery are protected by a that can be changed by s. Follow the steps below to change the in Acer eRecovery. 1. Boot to Window XP. 2. Press
+
to open the Acer eRecovery utility. 3. Enter the to proceed. The default is six zero. 4. In the Acer eRecovery window, select Recovery settings and click Next. 5. In the Recovery settings window, select : Change Acer eRecovery and click Next. Follow the instructions on screen to complete the process.
16 ed from www.Manualslib.com manuals search engine
Chapter 1
Acer Disc-to-Disc Recovery Restore without a Recovery CD This recovery process helps you restore the C:\ drive with the original software content that is installed when you purchase your system. Follow the steps below to rebuild your C:\ drive. Note: The C:\ drive will be reformatted and all data will be erased. It is important to back up all data files before you use this option. 1. Restart the system. 2. While the Acer logo comes out, press
+
to enter the recovery process. 3. The message The system has protection. Please enter 000000: will be displayed. 4. Enter six zeros and continue. 5. The Acer Recovery main page appears. 6. Use the arrow keys to scroll through the items (operating system versions) and press <Enter> to select.
Multilingual Operating System Installation Follow the instructions to choose the operating system and language you prefer when you first power on the system. 1. Turn on the system. 2. Acer’s multilingual operating system selection menu will pop up automatically. 3. Use the arrow keys to scroll to the language version you want. Press <Enter> to confirm your selection. 4. The operating system and language you choose now will be the only option for future recovery operations. 5. The system will install the operating system and language you choose.
Chapter 1 ed from www.Manualslib.com manuals search engine
17
Hardware Specification and Configuration Processor Item
Specification
Type
Sempron-D, Athlon64, Athlon64+ (for desktop U information in detail, please refer to http://www.intel.com/products/desktop/processors/ index.htm?iid=process+desktop)
System Main Chipset Item
Specification
Core logic
ATI RS690 + ATI SB600
Super I/O controller
ITE8718F with Hardware monitor
LAN controller
Marvell 88E8056, Gb PHY
Memory controller
ATI RS690
1394 controller
1394 header x 1 and Back I/O *1 (TSB43AB23PDTG4 2-port)
Serial ATA
Independent DMA operation on 4 ports, Data transfer rates up to 3.0Gbps
Audio subsystem controller
Realtek ALC888-GR, colay with ALC883
VGA controller
ATI RS690
North Bridge Item
Specification
General information
ATI RS690 s Core 2 Duo processors, DDR2 and DDR3 memory, and its graphics subsystem features a new graphics core twice as fast as the older Radeon Xpress 200.
Feature
• • • • • • • • • • •
Integrated a DirectX 9.0 compliant 2D/3D graphics core Integrated an ATI Radeon X700-based graphics engine s LDTSTP interface, U throttling, and stutter mode The RS690 incorporates ATI’s innovative Avivo™ display architecture A new TV encoder, based on design used in ATI’s Xilleon™ products RS690`s SURROUNDVIEW TM up to three independent monitors Integrated 400 MHz DAC for external desktop displays Primary HyperTransport link up to 1.0 GHz to the U One x4 A-link Express II interface (PCI Express 1.1 compliant) PCI Express 16 lane link interface for external graphics processors Dual PCI Express single lane link interface, with dedicated controller for other peripherals • Active power management, s ATI PowerOnDemand™ • 465-FCBGA package 21 mm × 21 mm
18 ed from www.Manualslib.com manuals search engine
Chapter 1
South Bridge Item
Specification
Chipset
ATI SB600
Feature
A-Link Express II interface to the RADEON IGPs: • 1/2/4-lane A-link Express II interface • Dynamic detection of lane configuration PCI Host Bus Controller: • PCI Rev. 2.3 specification • PCI Bus at 33MHz • up to 6 bus master device • 40-bit addressing USB Controller: • 5 OHCI and 1 EHCI Host controller to 10 USB ports • All10 ports are USB 1.1("Low speed", "Full speed") and 2.0("High speed") compatible • AI S1~S5 SMBus Controller: • SMBus Rev. 2.0 compliant • SMBALERT# signal/GPIO DMA Controller: • 2 cascaded 8237 DMA controllers • PC/PCI DMA • LPC DMA • type F DMA
Wake-up Event Specification (Default Setting in BIOS) S1
S3
S4
S5
Power button
Enable (default), Disabled
Enabled (default), Disabled
Enabled (default), Disabled
Enabled (default), Disabled
PS2 keyboard
Enabled, Disabled (default)
Enabled, Disabled (default)
N/A
N/A
USB keyboard
Enabled (default), Disabled
Enabled (default), Disabled
Enabled (default) Disabled
N/A
PME
Enabled (default), Disabled
Enabled (default), Disabled
Enabled (default), Disabled
Enabled (default), Disabled
Modem (ring)
Enabled, Disabled (default)
Enabled, Disabled (default)
Enabled, Disabled (default)
Enabled, Disabled (default)
RTC
Enabled, Disabled (default)
Enabled, Disabled (default)
Enabled, Disabled (default)
Enabled, Disabled (default)
Chapter 1 ed from www.Manualslib.com manuals search engine
19
Front LED States State for a Single Color Power LED (Blue) LED State
Description
AI State
Steady Blue
Running
S0
Blinking Blue
Sleeping
S1, S3
Off
Power Off
S4, S5
State for LAN LED (Blue) LED State
Description
Controller State
Blinking blue
Active
Active
Off
Idle
Idle
State for a Single Color Storage LED (Blue) LED State
Description
Controller State
Blinking blue
Active
Active
Off
Idle
Idle
System Memory Item
Specification
Feature
• Dual Channel DDR2 667/533/400, Unbuffered DIMM • 4 DDRII DIMM (8 GB Maximum capacity)
Super I/O Item
Description
Chip
ITE IT8718F
Feature
• • • • • • • •
Meet LPC Spec 1.1 Compliant with Microsoft PC98/PC2001 Hardware Design Guide PS/2 Keyboard & Mouse up to four 3.5-inch or 5.25-inch floppy disk drives two serial ports, one EPP/E parallel port three fans (5 fan speed monitoring inputs) IrDA 1.0 FIR protocol with maximum baud rate up to 115.2K bps Hardware Monitor ed (External Thermal Sensor Host )
USB Interface Item
Description
Chip
ATI SB600
Feature
• • • •
10 USB 2.0/1.1 ports Dual stack with RJ-45 back connector Dual stack with 1394 back connector 2 header ing 4 USB ports for front cabling and 1 header optional
20 ed from www.Manualslib.com manuals search engine
Chapter 1
Audio Interface Item
Description
Chip
Realtek ALC888 (high definition audio)
Feature
• High-performance DACs with 95dB SNR (A-Weighting), ADCs with 85dB SNR (A-Weighting) • Meets performance requirements for audio on PC2001 systems and Microsoft WLP 2.x • Ten DAC channels 16/20/24-bit PCM format, for 7.1 sound playback, plus 2 channels of independent stereo sound output through the front output. • 2 stereo ADCs 16/20/24-bit PCM format, one for stereo microphone, one for legacy mixer recording. • All DACs s 44.1K/48K/96K/192kHz sample rate • All ADCs 44.1K/48K/96K sample rate • 16/20/24-bit S/PDIF-OUT s 44.1K/48K/96K/192kHz sample rate • 16/20/24-bit S/PDIF-IN s 44.1K/48K/96K sample rate
1394 Interface Item
Description
Chip
TSB43AB23PDTG4
Feature
• Compliant with the IEEE 1394-1995 Release 1.0 and IEEE 1394a P2000 specifications with full 1394a P2000 • Compliant with the PCI V2.2 specification and card bus interfaces • Three 1394a ports enable connections at 100/200/400Mbps • Equipped with an OHCI compliant programming interface and I2C EEPROMs or four-wire serial ROMs
Hardware Monitor Function Item
Description
Feature
• Built-in 8-bit Analog to Digital Converter • 3 thermal inputs from remote thermal resistor or thermal diode or diodeconnected transistor • Provides VID0-VID7 for U Vcore identification • 8 voltage monitor inputs (VBAT is measured internally) • Watch dog comparison of all monitored values
Chapter 1 ed from www.Manualslib.com manuals search engine
21
BIOS Item
Description
BIOS code programmer
Phoenix Award
Version
Phoenix BIOS 6.00 PC
Feature
• ROM type: flash ROM • ROM size: 4MB • Protocol ed: PCIX 1.0, PCI 2.2, APM 1.2, VESA/DPMS (VBE/PM V1.1), SMBIOS 2.3, E-IDE 1.1, AI 1.0b, ESCD 1.03, PnP 1.0a, Bootable CD-ROM 1.0 • Boot from CD-ROM feature: yes • LS-120 FDD drive : yes • BIOS boot block feature: yes • s Microsoft SLP 2.0 for Windows Vista
Note: The BIOS can be overwritten/upgraded by using the flash utility.
BIOS Hotkey List Hotkey
Description
DEL
To enter BIOS Setup Utility: press the DEL key while the system is booting to enter BIOS Setup Utility.
Environment Requirements Item
Specification
Temperature Operating
+5OC ~ +35OC
Non-operating
-20OC ~ +60OC (storage packed), -10OC ~ +60OC (unpacked)
Humidity Operating
15% to 80% RH, non-condensing
Non-operating
10% to 90% RH, non-condensing at 40oC
Vibration Operating
5 ~ 500Hz, 2.20g RMS random, 10 minutes per axis in all three axes
Non-operating
5 ~ 500Hz, 1.09g RMS random, one hour per axis in all three axes
22 ed from www.Manualslib.com manuals search engine
Chapter 1
Power Management Function (AI Function) Device Standby Mode •
Independent power management timer for hard disk drive devices (zero to 15 minutes, time step = one minute).
•
Hard disk drive goes into Standby mode (for ATA standard interface).
•
Disable V-sync to control the VESA DPMS monitor.
•
Resume method: device activated (keyboard for DOS, keyboard & mouse for Windows).
•
Resume recovery time: three to five seconds.
Global Standby Mode •
Global power management timer (two to 120 minutes, time step = 10 minutes).
•
Hard disk drive goes into Standby mode (for ATA standard interface).
•
Disable H-sync and V-sync signals to control the VESA DPMS monitor.
•
Resume method: return to original state by pushing external switch button, modem ring in, keyboard and mouse for APM mode.
•
Resume recovery time: seven to 10 seconds.
Suspend Mode •
Independent power management timer (two to 120 minutes, time step = 10 minutes) or pushing external switch button.
•
U goes into SMM.
•
U asserts STPCLK# and goes into the Stop Grant state.
•
LED on the turns amber color.
•
Hard disk drive goes into SLEEP mode (for ATA standard interface).
•
Disable H-sync and V-sync signals to control the VESA DPMS monitor.
•
Ultra I/O and VGA chip go into power saving mode.
•
Resume method: return to original state by pushing external switch button, modem ring in, keyboard and mouse for APM mode.
•
Return to original state by pushing external switch button, modem ring in and USB keyboard for AI mode.
AI •
AI specification 1.0b
•
S0, S1, S3 and S5 sleep state
•
Onboard device power management
•
Onboard device configuration
Chapter 1 ed from www.Manualslib.com manuals search engine
23
24 ed from www.Manualslib.com manuals search engine
Chapter 1
Chapter 2
Setup Utility About the Setup Utility The computer uses the Phoenix Award BIOS (Basic Input and Output System) with for Windows Plug and Play. The CMOS chip on the main board contains the ROM setup instructions for configuring the main board BIOS. The BIOS Setup Utility displays the system’s configuration status and provides you with options to set system parameters. The parameters are stored in Battery-backed-up CMOS RAM that saves this information when the power is turned off. When the system is turned back on, the system is configured with the values you have stored in CMOS. The BIOS Setup Utility enables you to configure: •
Hard drives, diskette drives and peripherals
•
Video display type and display options
•
protection from unauthorized use
•
Power management features
The settings made in the Setup Utility affect how the computer performs. Before using the Setup Utility, ensure that you understand the Setup Utility options. This Setup Utility should be used: •
when changing the system configuration
•
when a configuration error is detected and you are prompted to make changes to the Setup Utility
•
when trying to resolve IRQ conflicts
•
when making changes to the Power Management configuration
•
when changing the or making other changes to the Security Setup
Control Keys Item
Description
IKLJ
Move to the item you want to select
ENTER
Select the item you want or enter the sub-menu
ESC
Retreat from the current page
Pg Up
Increase the numeric value or make changes
Pg Dn
Decrease the numeric value or make changes
F1
General help
F5
Restore the previous CMOS value from CMOS
F7
Load the factory default setting
F10
Save all the CMOS changes
Exit
Leave the Setup Utility
Chapter 2 ed from www.Manualslib.com manuals search engine
25
Entering the Setup Utility Power on the computer and the system will start POST (Power On Self Test). When the message Press DEL to enter SETUP appears on the screen, press the DEL key to enter the setup menu. Once you enter the Phoenix Award BIOS CMOS Setup Utility, the main menu will appear on the screen. Use arrow keys to select the item you want and press ENTER to confirm the setting or enter the sub-menu.
Phoenix - Award WorkstationBIOS CMOS Setup Utility XProduct Information
XPC Health Status
XStandard CMOS Features
XFrequency/Voltage Control
XAdvanced BIOS Features
Load Optimized Defaults
XAdvanced Chipset Features
Set Supervisor
XIntegrated Peripherals
Set
XPower Management Setup
Save & Exit Setup
XPnP/PCI Configuration
Exit Without Saving
KLIJ :Move Enter: Select +/-/ :Value F10:Save ESC:Exit F1:General Help F9:Optimized Defaults Standard CMOS setup for changing time, date, hard disk type, etc.
26 ed from www.Manualslib.com manuals search engine
Chapter 2
Product Information This page displays product information about your system. You can press ESC to return to the main menu setting page.
Phoenix - Award WorkstationBIOS CMOS Setup Utility Product Information Product Name
Aspire M5188
System S/N Mainboard ID
F690CVM
Help Item Menu Level
X
Asset Tag Number System BIOS Version
6.00PC
SMBIOS Version
2.4
System BIOS ID
721A1D04
BIOS Release Date
03/17/2007
KLIJ :Move Enter: Select +/-/PU/PD :Value F10: Save and Exit ESC:Exit F1: General Help
Chapter 2 ed from www.Manualslib.com manuals search engine
F5: Previous Values
F7: Optimized Defaults
27
Standard CMOS Features This page displays the standard CMOS features. You can press ESC to return to the main menu setting page.
Phoenix - Award WorkstationBIOS CMOS Setup Utility Standard CMOS Features Date (mm:dd:yy)
Thu, Apr 12 2007
Time (hh:mm:ss)
10 : 32 : 39
Help Item Menu Level
X
XIDE Channel 0 Master
[None]
Change the day, month,
XIDE Channel 0 Slave
[None]
year and century.
XIDE Channel 2 Master
[None]
XIDE Channel 2 Slave
[None]
XIDE Channel 3 Master
[None]
XIDE Channel 3 Slave
[None]
Drive A
None
Halt On
[All, But Keyboard]
Base Memory
640K
Extended Memory
1833984K
Total Memory
1835008K
KLIJ :Move Enter: Select +/-/PU/PD :Value F10: Save and Exit ESC:Exit F1: General Help
F5: Previous Values
F7: Optimized Defaults
Date and Time The Date and Time items show the current date and time set on the computer. If you are running a Windows OS, these items are automatically updated whenever you make changes to the Windows Date and Time Properties utility.
SATA Devices This main board features four SATA connectors ing four SATA drives. SATA refers to Serial ATA (Advanced Technology Attachment), the standard interface for the IDE hard drives which are currently used in most PCs.
Drive A This item will identify the type of floppy disk drive A that has been installed.
Halt On This item determines whether the system stops or not if an error occurs during system boot-up. At defaults All, But Keyboard, the boot will be interrupted for all errors except a keyboard error.
Base Memory, Extended Memory, and Total Memory These items are automatically detected by the system at start-up time. You can not make changes to these fields.
28 ed from www.Manualslib.com manuals search engine
Chapter 2
Advanced BIOS Features This page displays advanced BIOS features. You can press ESC to return to the main menu setting page.
Phoenix - Award WorkstationBIOS CMOS Setup Utility Advanced BIOS Features XHard Disk Boot Priority
[Press Enter]
Virus Warning
[Disabled]
U Internal Cache
[Enabled]
External Cache
[Enabled]
Quick Power On Self Test
[Enabled]
First Boot Device
[Hard Disk]
Second Boot Device
[CDROM]
Third Boot Device
[Disabled]
Boot Other Device
[Enabled]
Boot Up Floppy Seek
[Disabled]
Boot Up Num Lock Status
[On]
Gate A20 Option
[Fast]
Typematic Rate Setting
[Disabled]
X Typematic Rate (chars/sec)
6
X Typematic Delay (Msec)
250
Security Option
[Setup]
APIC Mode
Enabled
MPS Version Control For OS
[1.4]
OS Select For DRAM > 64MB
[Non-OS2]
HDD S.M.A.R.T. Capability
[Disabled]
Silent Boot
[Enabled]
Small Logo (EPA) Show
[Disabled]
Configuration Table
[Disabled]
Bootblock Write Protect
[Enabled]
Help Item Menu Level
X
KLIJ :Move Enter: Select +/-/PU/PD :Value F10: Save and Exit ESC:Exit F1: General Help
F5: Previous Values
F7: Optimized Defaults
Virus Warning This item enables or disables the boot sector virus protection.
U Internal Cache/External Cache Cache memory is additional memory that is much faster than conventional DRAM (system memory). Us from 486-type on up contain internal cache memory, and most, but not all, modern PCs have additional (external) cache memory. When the U requests data, the system transfers the requested data from the main DRAM into cache Chapter 2 ed from www.Manualslib.com manuals search engine
29
memory, for even faster access by the U. Disabling the Internal/External Caching may affect processing speeds.
Quick Power On Self Test Use this item to shorten the POST and have the system startup faster. You might like to enable this item after you are confident that your system hardware is operating smoothly.
First / Second / Third Boot Device Use this three items to select the priority and order of the devices that your system searches for an operating system when the system is powering on.
Boot Other Device When enabled, the system searches all other possible locations for an operating system if it fails to find one in the devices specified under the First, Second, and Third boot devices.
Boot Up Floppy Seek This item controls whether the BIOS checks for a floppy drive while booting up.
Boot Up NumLock Status This item defines if the keyboard NumLock key is active when your system is booted.
Gate A20 Option This item defines how the system handles legacy software that was written for an earlier generation of processors. Set this item for the default value.
Typematic Rate Setting If this item is enabled, you can use the following two items to set the Typematic Rate and the Typematic Delay settings for the keyboard. The default setting is
which uses the defaults below: •
Typematic Rate (Chars/Sec): Use this item to define how many characters per second are generated by a held-down key. The default setting is 6.
•
Typematic Delay (Msec): Use this item to define how many milliseconds must elapse before a held-down key begins generating repeat characters. The default setting is 250.
Security Option If you have installed protection, this item defines if the is required at system start up, or if it is only required when a tries to enter the Setup Utility.
APIC Mode This item allows you to enable or disable the APIC (Advanced Programmable Interrupt Controller) mode. APIC provides symmetric multi-processing (SMP) for systems.
MPS Version Control For OS This item specifies which version of MPS (Multi-Processor Specification) this main board will use. Set this item for its default setting.
OS Select for DRAM > 64 MB This item is only required if you have installed more than 64 MB of memory and you are running the OS/2 operating system. Otherwise, leave this item at the default.
30 ed from www.Manualslib.com manuals search engine
Chapter 2
HDD S.M.A.R.T Capability The S.M.A.R.T (Self-Monitoring, Analysis, and Reporting Technology) system is a diagnostics technology that monitors and predicts device performance. S.M.A.R.T software resides on both the disk drive and the host computer.
Silent Boot This item enables or disables the Silent Boot function.
Small Logo (EPA) Show Determines whether the EPA logo appears during boot up.
Configuration Table This item enables or disables the Configuration Table in BIOS setting.
Bootblock Write Protect When enabled, Boot block write protection allows the boot block area to be protected by a write-protect pin.
Chapter 2 ed from www.Manualslib.com manuals search engine
31
Hard Disk Boot Priority Scroll to this item and press ENTER to enter the sub-menu below.
Phoenix - Award WorkstationBIOS CMOS Setup Utility Hard Disk Boot Priority 1. Ch2 M.
: ST3808110AS
Help Item
2. Bootable Add-in Cards
Menu Level
XX
Use
or
to select a device, then press <+> to move it up, or <-> to move it down the list. Press <Esc> to exit this menu.
KLIJ :Move Enter: Select +/-/PU/PD :Value F10: Save and Exit ESC:Exit F1: General Help
32 ed from www.Manualslib.com manuals search engine
F5: Previous Values
F7: Optimized Defaults
Chapter 2
Advanced Chipset Features These items define critical timing parameters of the main board. You should set these items for their default values unless you are very familiar with the technical specification of your system hardware. If you change the values incorrectly, you may introduce fatal errors or recurring instability into your system.
Phoenix - Award WorkstationBIOS CMOS Setup Utility Advanced Chipset Features UMA Frame Buffer Size
[Auto]
Current UMA Size
256MB
Memory Hole
[Disabled]
System BIOS Cacheable
[Disabled]
Help Item Menu Level
X
KLIJ :Move Enter: Select +/-/PU/PD :Value F10: Save and Exit ESC:Exit F1: General Help
F5: Previous Values
F7: Optimized Defaults
UMA Frame Buffer Size This option controls the amount of system memory that is allocated to the integrated graphics processor when the system boots up.
Memory Hole You can reserve this area of system memory for ISA adapter ROM. When this area is reserved, it cannot be cached. The information of peripherals that use this area of system memory need to state their memory requirements.
System BIOS Cacheable Selecting [Enabled] allows caching of the system BIOS ROM at F0000h-FFFFFh, resulting in better system performance. However, if any program writes to this memory area, a system error may result. The default setting is [Disabled].
Chapter 2 ed from www.Manualslib.com manuals search engine
33
Integrated Peripherals Phoenix - Award WorkstationBIOS CMOS Setup Utility Integrated Peripherals XSouth OnChip IDE Device
[Press Enter]
XSouth OnChip PCI Device
[Press Enter]
XSuper IO Device
[Press Enter]
Init Display First
Help Item Menu Level
X
[PCIEx]
KLIJ :Move Enter: Select +/-/PU/PD :Value F10: Save and Exit ESC:Exit F1: General Help
F5: Previous Values
F7: Optimized Defaults
South OnChip IDE Device Press Enter to view the South OnChip IDE Device submenu. See “South OnChip IDE Device” on page 35.
South OnChip PCI Device Press Enter to view the South OnChip IDE Device submenu. See “South OnChip PCI Device” on page 36.
Super IO Device Press Enter to view the South OnChip PCI Device submenu. See “Super IO Device” on page 38.
Init Display First Enables or disables the bus PCI Slot or Onboard/AGP.
34 ed from www.Manualslib.com manuals search engine
Chapter 2
South OnChip IDE Device Scroll to this item and press Enter to enter the sub-menu shown as below.
Phoenix - Award WorkstationBIOS CMOS Setup Utility South OnChip IDE Device IDE DMA transfer access
[Enabled]
OnChip IDE Channel 0
[Enabled]
Primary Master PIO
[Auto]
Primary Slave PIO
[Auto]
Primary Master UDMA
[Auto]
Primary Slave UDMA
[Auto]
IDE HDD Block Mode
[Enabled]
Help Item Menu Level
X
KLIJ :Move Enter: Select +/-/PU/PD :Value F10: Save and Exit ESC:Exit F1: General Help
F5: Previous Values
F7: Optimized Defaults
IDE DMA Transfer Access This item allows you to enable the transfer access of the IDE DMA.
OnChip IDE Channel Select Enabled to activate IDE channel.
IDE Primary/Secondary Master/Slave PIO Each IDE channel s a master device and a slave device. These four items let you assign which kind of PIO (Programmed Input/Output) is used by IDE devices. Choose Auto to let the system auto detect which PIO mode is optimal, or select a PIO mode from zero to four.
IDE Primary/Secondary Master/Slave UltrA This main board s UltrA technology, which provides faster access to IDE devices. If you install a device that s UltrA, you can change the item on this list to Auto. You may have to install the UltrA driver supplied with this main board in order to use an UltrA device.
IDE HDD Block Mode Enable this field if the IDE hard drive s block mode. Block mode enables BIOS to automatically detect the optimal number of block read and writes per sector that the drive can and improves the speed of access to IDE devices. Chapter 2 ed from www.Manualslib.com manuals search engine
35
South OnChip PCI Device Scroll to this item and press Enter to enter the sub-menu shown as below.
Phoenix - Award WorkstationBIOS CMOS Setup Utility South OnChip PCI Device ATI Azalia Audio
[Enabled]
ATI SATA Controller
[Enabled]
ATI SATA Type
[Native IDE]
USB EHCI Controller
[Enabled]
OnChip USB Controller
[Enabled]
OnChip USB KBC Controller
[Enabled]
USB Mouse
[Enabled]
Onboard LAN Controller
[Enabled]
Onboard Lan Boot ROM
[Enabled]
Onboard 1394 Controller
[Enabled]
Help Item Menu Level
X
KLIJ :Move Enter: Select +/-/PU/PD :Value F10: Save and Exit ESC:Exit
ATI Azalia Audio ATI Azalia Audio provides superior Audio Onboard, negating the need for 3rd party audio cards. The default setting is [Enabled].
ATI SATA Controller This item appears in the BIOS of motherboards with a secondary Serial ATA controller (separate from the motherboard chipset). When enabled, the secondary Serial ATA controller will function normally. Serial ATA devices connected to it will be accessible to the system. When disabled, the secondary Serial ATA controller will be disabled. Serial ATA devices connected to it will not be accessible to the system.
ATI SATA Type This item sets the SATA Cable Type in use. The default is [Native IDE].
USB EHCI Controller Enables or disables the Universal Serial Bus (USB) controller and Enhanced Host Controller Interface.
36 ed from www.Manualslib.com manuals search engine
Chapter 2
OnChip USB Controller Enables or disables the Universal Serial Bus (USB) controller and any USB peripherals present.
OnChip USB KBC Controller Enables or disables the Universal Serial Bus (USB) controller and USB keyboard if present.
USB Mouse You can enable this item if you want to use a mouse connected through the USB port in a legacy operating system (such as DOS) that does not Plug and Play.
Onboard LAN Controller This item allows s to enable or disable the onboard LAN Controller function.
Onboard Lan Boot ROM Use this item to enable or disable the booting from the onboard LAN or a network add-on card with a remote boot ROM installed.
Onboard 1394 Controller Use this item to enable or disable the onboard VIA 1394 device.
Chapter 2 ed from www.Manualslib.com manuals search engine
37
Super IO Device Phoenix - Award WorkstationBIOS CMOS Setup Utility Super IO Device Onboard FDC Controller
[Enabled]
Onbaord Serial Port 1
[3F8/IRQ4]
Onbaord Serial Port 2
[2F8/IRQ3]
UART Mode Select
[Normal]
X UR2 Duplex Mode
Menu Level
X
Half
Onboard Parallel Port
[378/IRQ7]
Parallel Port Mode
SPP
X E Mode Use DMA
Help Item
3
KLIJ :Move Enter: Select +/-/PU/PD :Value F10: Save and Exit ESC:Exit F1: General Help
F5: Previous Values
F7: Optimized Defaults
Onboard FDC Controller If your system has a floppy disk controller (FDC) installed on the system board and you want to use it, you can select Enabled. If you install an add-in FDC or the system has no floppy drive, select Disabled in this field.
Onboard Serial Port 1 This item allows s to manually set the address for serial port 1.
Onboard Serial Port 2 Use this item to enable or disable the onboard parallel port and to assign a port address.
UART Mode Select Select an operating mode for the serial port. The default is [Normal].
UR2 Duplex Mode This option is only available if an infrared port mode is selected in the UART Mode Select item. Select full or half duplex mode. Full-duplex mode permits simultaneous two-direction transmission. Half-duplex mode permits transmission in one direction only at a time. 38 ed from www.Manualslib.com manuals search engine
Chapter 2
Onboard Parallel Port Select a logical LPT port address and corresponding interrupt for the onboard parallel port.
Parallel Port Mode Use this item to set the parallel port mode. You can select SPP (Standard Parallel Port), E (Extended Capabilities Port), EPP (Enhanced Parallel Port), or EPP & E.
E Mode Use DMA When the onboard parallel port is set for E mode, the parallel port can use (DMA) 3 or (DMA) 1.
Chapter 2 ed from www.Manualslib.com manuals search engine
39
Power Management Setup The system has various power-saving modes including powering down the hard disk, turning off the video, suspending to RAM, and software power down that allows the system to be automatically resumed by certain events. The power-saving modes can be controlled by time-outs. If the system is inactive for a while, the time-outs begin counting. If the inactivity continues so that the time-out period elapses, the system enters a power-saving mode. If any item in the list of Reload Global Timer Events is Enabled, then any activity on that item will reset the time-out counters to zero. If the system is suspended or has been powered down by software, it can be resumed by a wake up call that is generated by incoming traffic to a modern, a LAN card, a PCI card, or a fixed alarm on the system real-time clock.
Phoenix - Award WorkstationBIOS CMOS Setup Utility Power Management Setup AI function
[Enabled]
AI Suspend Type
[S3(STR)]
C2 Disable/Enable
[Disabled]
Power Management Option
[ Define]
HDD Power Down
[Disabled]
Video Off Option
[Suspend -> Off]
Video Off Method
[V/H SYNC+Blank]
Soft-Off by PWRBTN
[Delay 4 sec]
PowerOn by PCI Card
[Enabled]
Modem Ring Resume
[Disabled]
USB Wake Up From S1/S2
[Enabled]
USB Wake Up From S4
[Disabled]
PS2 KB/MS Wake Up S1/S2
[Disabled]
Wake Up by Lan
[Disabled]
HPET
[Enabled]
PWRON After PWR-Fail
[Former-Sts]
RTC Alarm Resume
[Disabled]
X Date (of Month) X Resume Time (hh : mm : ss)
Help Item Menu Level
X
0 0: 0:0
KLIJ :Move Enter: Select +/-/PU/PD :Value F10: Save and Exit ESC:Exit F1: General Help
F5: Previous Values
F7: Optimized Defaults
AI Function This item allows s to enable or disable the AI power management function.
AI Suspend Type You can use this item to define how your system suspends. 40 ed from www.Manualslib.com manuals search engine
Chapter 2
CS2 Disable/Enable Enable or disable the AI C2 mode. Default is Disabled.
Power Management Option This item acts like a master switch for the power-saving modes and hard disk timeouts. If this item is set to Max Saving, power-saving modes occur after a short timeout. If this item is set to Min Saving, power-saving modes occur after a longer timeout. If the item is set to Define, manually define timeouts for the power-saving modes.
HDD Power Down Select the required period of inactivity after which the hard disk drive powers down while all other devices remain active.
Video Off Option This option defines if the video is powered down when the system is put into suspend mode.
Video Off Method This item defines how the video is powered down to save power.
Soft-Off by PWRBTN Under AI (Advanced Configuration and Power Management Interface) you can create a software power down. In a software power down, the system can be resumed by Wake Up Alarms. This item lets you install a software power down that is controlled by the power button on your system. If the item is set for Instant-Off, then the power button causes a software power down. If the item is set for Delay four Sec., then you have to hold the power button down for four seconds to cause a software power down.
Power On By PCI Card Enables PCI activity to wake up the system from a power-saving mode.
Modem Ring Resume Enables Modem activity to wake up the system from a power-saving mode.
USB Wakeup From S1/S2 Enables USB activity to wake up the system from S1 or S2.
USB Wakeup From S4 Enables USB activity to wake up the system from S4.
PS2 KB/MS Wakeup From S1/S2 Enables PS/2 keyboard or mouse activity to wake up the system from S1 or S2.
Wakeup By LAN Enables LAN activity to wake up the system from a power-saving mode.
HPET Enable or disable for the High Precision Event Timer (HPET).
PWRON After PWR-Fail Sets the state to which the computer returns after power failure. Chapter 2 ed from www.Manualslib.com manuals search engine
41
RTC Alarm Resume When set to Enabled, the Date and Resume Time fields become available. Set the date (day of the month), hour, minute and second to turn on the system. When set to 0 (zero) for the day of the month, the alarm will power on your system every day at the specified time.
42 ed from www.Manualslib.com manuals search engine
Chapter 2
PnP/PCI Configurations It configures how PnP (Plug and Play) and PCI expansion cards operate in your system. Both the ISA and PCI buses on the main board use system IRQs (interrupt requests) and DMAs (direct memory access). You must set up the IRQ and DMA assignments correctly through the PnP/PCI Configurations Setup Utility for the main board to work properly. Selecting PnP/PCI Configurations on the main program screen displays the menu below.
Phoenix - Award WorkstationBIOS CMOS Setup Utility PnP/PCI Configurations Reset Configuration Data
[Disabled]
Resources Controlled By
[Auto(ESCD)]
X IRQ Resources
Help Item Menu Level
X
Press Enter
PCI/VGA Palette Snoop
[Disabled]
Assign IRQ For VGA
[Enabled]
Assign IRQ For USB
[Enabled]
PC Latency Timer (CLK)
[64]
**PCI Express relative items** Maximum Payload Size
[4096]
KLIJ :Move Enter: Select +/-/PU/PD :Value F10: Save and Exit ESC:Exit F1: General Help
F5: Previous Values
F7: Optimized Defaults
Reset Configuration Data Select Enabled to reset the Extended System Configuration Data (ESCD) when you exit setup. This option is useful when installing new add-ons. If the computer cannot boot after add-on installation, this option resets the ESCD allowing the computer to reboot. The default setting is disabled.
Resources Controlled By The BIOS can automatically configure all the boot Plug and Play compatible devices. Auto (default) disables IRQ and DMA memory base address fields as they are automatically assigned.
PCI/VGA Palette Snoop This item is designed to overcome problems that can be caused by some non-standard VGA cards. This board includes a built-in VGA system that does not require palette snooping. Default setting is [Disabled].
Assign IRQ For VGA Enable or disable IRQ allocation for the graphics card.
Chapter 2 ed from www.Manualslib.com manuals search engine
43
Assign IRQ for USB Enable or disable IRQ allocation for the USB (Universal Serial Bus).
PCI Latency Timer (CLK) This item controls how long a PCI device can hold the PCI bus before another device takes over. Setting the latency to longer periods enables a PCI device to retain control of the bus longer before handing it over to another device.
Maximum Payload Size This BIOS feature determines the maximum TLP (Transaction Layer Packet) payload size that can be ed by the motherboard chipset's PCI Express controller. The TLP payload size determines the amount of data transmitted within each data packet. When set to 4096, the motherboard chipset's PCI Express controller s the maximum data payload of 4096 bytes within each TLP. This is the maximum payload size currently ed by the PCI Express protocol.
44 ed from www.Manualslib.com manuals search engine
Chapter 2
PC Health Status On the main board that s hardware monitoring, you can monitor the parameters of critical voltage, temperature and fan speed.
Phoenix - Award WorkstationBIOS CMOS Setup Utility PC Health Status U Shutdown Temperature
[90°C/174°C]
U Vcore
[1.34V]
+3.3V
[3.32V]
+5V
[5.08V]
+12V
[11.96V]
+5VSB
[4.94V]
U Temperature
64°C
Ambient Temperature
31°C
U FAN speed
1844 RPM
System FAN speed
1790 RPM
U Temp. Offset
[255]
U Warning Temperature
[Disabled]
U Smart FAN Control
[Enabled]
PWM Start U Temp (°C)
[ 35]
Start PWM Value (0~127)
[ 64]
Slope PWM Value
[ 3]
Delta Temp. (°C)
[ 2]
PWM Start SYS Temp. (°C)
[ 45]
Slope PWM Value 2
[ 2]
Delta Temp. (°C) 2
[ 2]
System Smart FAN Control
[Enabled]
PWM Start U Temp (°C)
[ 45]
Start PWM Value (0~127)
[ 48]
Slope PWM Value
[ 2]
Delta Temp. (°C)
[ 2]
PWM Start SYS Temp. (°C)
[ 42]
Slope PWM Value 2
[ 3]
Delta Temp. (°C) 2
[ 2]
Help Item Menu Level
X
KLIJ :Move Enter: Select +/-/PU/PD :Value F10: Save and Exit ESC:Exit F1: General Help
F5: Previous Values
F7: Optimized Defaults
U Shut Down Temperature Enables you to set the maximum temperature that the system can reach before powering down.
Chapter 2 ed from www.Manualslib.com manuals search engine
45
Component Status The following items display the current status of various components. •
U VCore
•
+3.3V
•
+5V
•
+12V
•
+5VSB
•
U Temperature
•
Ambient Temperature
•
U FAN speed
•
System FAN speed
Scroll to these items and enter values as required to customize the Thermal Profile: •
U Temp. Offset
•
U Warning Temperature
•
U Smart FAN Control
•
PWM Start U Temp
•
Start PWM Value
•
Slope PWM Value
•
Delta Temp.
•
PWM Start SYS Temp.
•
Slope PWM Value 2
•
Delta Temp. (°C) 2
•
System Smart FAN Control
•
PWM Start U Temp (°C)
•
Start PWM Value (0~127)
•
Slope PWM Value
•
Delta Temp. (°C)
•
PWM Start SYS Temp. (°C)
•
Slope PWM Value 2
•
Delta Temp. (°C) 2
46 ed from www.Manualslib.com manuals search engine
Chapter 2
Frequency & Voltage Control It enables you to set the clock speed and system bus for your system. The clock speed and system bus are determined by the processor you have installed in your system.
Phoenix - Award WorkstationBIOS CMOS Setup Utility Frequency/Voltage Control Spread Spectrum
[Disabled]
SB600 Spread Spectrum
[Disabled]
Help Item Menu Level
X
KLIJ :Move Enter: Select +/-/PU/PD :Value F10: Save and Exit ESC:Exit F1: General Help
F5: Previous Values
F7: Optimized Defaults
Spread Spectrum If you enable spread spectrum, it can significantly reduce the EMI (Electro-Magnetic Interference) generated by the system.
SB600 Spread Spectrum Enabling spread spectrum can significantly reduce the EMI (ElectroMagnetic Interference) generated by the south bridge. For maximum system stability and performance this settings should remain at the default setting [Disabled].
Chapter 2 ed from www.Manualslib.com manuals search engine
47
Load Optimized Defaults This option opens a dialog box that lets you install optimized defaults for all appropriate items in the Setup Utility. Press Y and then ENTER to install the defaults. Press N and then ENTER to cancel without installing defaults.
Phoenix - Award WorkstationBIOS CMOS Setup Utility XProduct Information
XPC Health Status
XStandard CMOS Features
XFrequency/Voltage Control
XAdvanced BIOS Features
Load Optimized Defaults
XAdvanced Chipset Features
Set Supervisor
XIntegrated Peripherals
Set
XPower Management Setup XPnP/PCI Configuration
Save & Exit Setup Load Optimized Defaults (Y/N)? Exit Without Saving
KLIJ : Select Item
Esc: Quit F10: Save & Exit Setup
Load Optimized Defaults V02.54 (C) Copyright 1985-2004, American Megatrends, Inc.
48 ed from www.Manualslib.com manuals search engine
Chapter 2
Set Supervisor When this function is selected, the following message appears at the center of the screen to assist you in creating a .
Phoenix - Award WorkstationBIOS CMOS Setup Utility XProduct Information
XPC Health Status
XStandard CMOS Features
XFrequency/Voltage Control
XAdvanced BIOS Features
Load Optimized Defaults
XAdvanced Chipset Features
Set Supervisor
XIntegrated Peripherals XPower Management Setup XPnP/PCI Configuration
Set Enter :Save & Exit Setup
Exit Without Saving
KLIJ : Select Item
Esc: Quit F10: Save & Exit Setup
Change/Set/Disable V02.54 (C) Copyright 1985-2004, American Megatrends, Inc.
Enter Type the , up to eight characters, and press ENTER. The entered here overwrites any previously entered from CMOS memory. You will be asked to confirm the . Type the again and press ENTER. You can press ESC to abort the selection. To disable , just press ENTER when you are prompted to enter . A message will confirm the being disabled. Once the is disabled, the system will boot and you can enter BIOS Setup freely. Supervisor has higher priority than . You can use Supervisor when booting the system or entering BIOS Setup to modify all settings. Also you can use when booting the system or entering BIOS Setup but can not modify any setting if Supervisor is enabled.
Chapter 2 ed from www.Manualslib.com manuals search engine
49
Save and Exit Setup You can highlight this item and press ENTER to save the changes that you have made in the Setup Utility and exit the Setup Utility.
Phoenix - Award WorkstationBIOS CMOS Setup Utility XProduct Information
XPC Health Status
XStandard CMOS Features
XFrequency/Voltage Control
XAdvanced BIOS Features
Load Optimized Defaults
XAdvanced Chipset Features
Set Supervisor
XIntegrated Peripherals XPower Management Setup XPnP/PCI Configuration
Set
SAVE to CMOS and EXIT (Y/N)?
Save & Exit Setup Exit Without Saving
KLIJ : Select Item
Esc: Quit F10: Save & Exit Setup
Save Data to CMOS V02.54 (C) Copyright 1985-2004, American Megatrends, Inc. When the Save and Exit dialog box appears, press (Y) followed by ENTER to save and exit, or press (N) followed by ENTER to return to the main menu.
50 ed from www.Manualslib.com manuals search engine
Chapter 2
Exit without Saving You can highlight this item and press ENTER to discard any changes that you have made in the Setup Utility and exit the Setup Utility.
Phoenix - Award WorkstationBIOS CMOS Setup Utility XProduct Information
XPC Health Status
XStandard CMOS Features
XFrequency/Voltage Control
XAdvanced BIOS Features
Load Optimized Defaults
XAdvanced Chipset Features
Set Supervisor
XIntegrated Peripherals XPower Management Setup XPnP/PCI Configuration
Set Quit Without Saving Save(Y/N)? & Exit Setup
Exit Without Saving
KLIJ : Select Item
Esc: Quit F10: Save & Exit Setup
Abandon All Data V02.54 (C) Copyright 1985-2004, American Megatrends, Inc. When the Exit without Saving dialog box appears, press (Y) followed by ENTER to discard changes and exit, or press (N) followed by ENTER to return to the main menu. Note: If you have made changes to settings that you do not want to save, choose the Discard Changes and Exit and press (Y) followed by ENTER to discard any changes you have made.
Chapter 2 ed from www.Manualslib.com manuals search engine
51
52 ed from www.Manualslib.com manuals search engine
Chapter 2
Chapter 3
Machine Disassembly and Replacement General Information This chapter contains step-by-step procedures on how to disassemble and reassemble the Angora AM5610/ AM3610 for maintenance and troubleshooting. In the coming pages, the first part of the disassembly instruction is for Angora AM5610 and the second part is for Angora AM3610. To disassemble the notebook, you need the tools below: •
Wrist ground strap and conductive mat for preventing electrostatic discharge
•
Small Philips screw driver
•
Flat head screw driver
•
Hexagonal driver
•
Tweezers
Note: The screws for the different components vary in size. During the disassembly process, group the screws with the corresponding components to avoid mismatch when putting back the components. When you remove the stripe cover, please be careful not to scrape the cover.
Before You Begin Before proceeding with the disassembly procedure, you have to make sure that: •
The system and all peripherals are powered off.
•
The AC adaptor and all power and signal cables from the system are unplugged.
Note: There are several types of screws used to secure the main unit. The screws vary in length. Please refer to the screws table after the flowchart. Group the same type of screws together during service disassembling. Please also the screw location for each screw type. If you fasten the screws on the wrong location, the long screws may cause irrecoverable damage to the main board.
Chapter 3 ed from www.Manualslib.com manuals search engine
53
Angora AM50/30/10 Procedures Use the following guides to disassemble and reassemble the AM50, AM30, and AM10 models. Note: The only differences between the models are the front bezel and placement of the USB as shown below. Take care when replacing the front bezel to avoid damage to the ports. AM50
AM30
AM10
Disassembly Procedure 1. Place the system unit on a flat, steady and nonskid surface. 2. Release the lock handle then slide the left cover out.
3. Detach the VGA, TV, and Modem cards.
54 ed from www.Manualslib.com manuals search engine
Chapter 3
4. Disconnect the front bezel LED cable.
5. Disconnect the audio cables.
6. Disconnect the USB cables.
7. Disconnect the SPDIF cable.
Chapter 3 ed from www.Manualslib.com manuals search engine
55
8. Disconnect the PA power cable from the MB connector.
9. Disconnect the P1 power and FDD data cables. P1 Power Cable
FDD Data Cable
10. Disconnect the ODD power and data cables. ODD Power Cable ODD Data Cable
56 ed from www.Manualslib.com manuals search engine
Chapter 3
11. Disconnect the HDD power and data cables.
12. Disconnect the System Fan and U Cooler power cable from their MB connectors. U Cooler
System Fan
13. Slide the HDD holder as shown and remove the HDD from the chassis.
Chapter 3 ed from www.Manualslib.com manuals search engine
57
14. Release the three securing latches and remove the front bezel. Note: For the AM50 and AM30, take care not to damage the USB ports at the top of the bezel. Note: For the AM10, take care not to damage the USB ports on the bottom right-hand side of the bezel. AM50
AM30
AM10
15. Slide the ODD holder as shown and remove the HDD from the chassis.
16. Release the four screws as shown and remove the U Cooler from the chassis.
58 ed from www.Manualslib.com manuals search engine
Chapter 3
17. Push the two locking latches away from the memory unit at the same time to release the memory. Repeat as necessary to remove all memory.
18. Remove the four System Fan screws as shown and lift the fan clear of the chassis.
19. Push and release the U latch and remove the U from the motherboard.
Chapter 3 ed from www.Manualslib.com manuals search engine
59
20. Release the 8 screws marked below and remove the main board.
21. Release the four screws marked below and remove the system power supply from the chassis.
60 ed from www.Manualslib.com manuals search engine
Chapter 3
Reassembly Procedure 1.
Insert the system power supply in to the chassis and secure the four screws marked below.
IMPORTANT:FSP and LITEON power supply cabling differ due to size constraints. For FSP power supplies, use a power cable clip to secure the 12V cable. For LITEON power supplies, use a non-cable clip to secure the 12V cable. FSP Power Supply
LITEON Power Supply
2. Insert the main board and secure the 8 screws marked below. Note: Ensure that the I/O Connector is aligned and that the VIA aperture is correctly oriented with the STAND OFF on the chassis.
Chapter 3 ed from www.Manualslib.com manuals search engine
61
3. Insert the U in to the motherboard. Close the U latch.
4. Insert the System Fan in to the chassis as secure the 4 screws as shown.
5. Insert the memory into the slot, taking care to align the locating lug. Push down as shown until the securing latches click into place. Repeat for all memory modules.
62 ed from www.Manualslib.com manuals search engine
Chapter 3
6. Fit the U cooler to the MB and fasten the four screws shown bellow.
7. Connect the System Fan & U Cooler power-cables to the MB connectors. U Cooler
System Fan
8. Insert the ODD in to the chassis and slide the ODD holder as shown to lock it in place.
Chapter 3 ed from www.Manualslib.com manuals search engine
63
9. Insert the FDD in to the chassis and slide the FDD holder as shown to lock it in place.
10. Attach the front bezel as shown. Ensure that access to the USB ports is not restricted as indicated for the three models. AM50
AM30
AM10
11. Insert the SPDIF into the chassis. Ensure that the unit locates correctly as shown.
12. Insert the HDD in to the chassis and slide the HDD holder as shown to lock it in place.
64 ed from www.Manualslib.com manuals search engine
Chapter 3
13. Connect the HDD data cable and HDD power cable.
14. Connect the ODD data cable and power-cable to the rear of ODD. ODD Power Cable ODD Data Cable
15. Connect the P1 power-cable and FDD data cable to the MB connector. P1 Power Cable
Chapter 3 ed from www.Manualslib.com manuals search engine
FDD Data Cable
65
16. Connect the PA power-cable to the MB connector.
17. Connect the USB cables.
18. Connect the SPDIF cable.
19. Connect the audio cables.
66 ed from www.Manualslib.com manuals search engine
Chapter 3
20. Connect the front bezel LED cable.
21. Connect the VGA/TV, and Modem cards.
22. Slide the left cover in and secure the lock handle.
Chapter 3 ed from www.Manualslib.com manuals search engine
67
68 ed from www.Manualslib.com manuals search engine
Chapter 3
Chapter 4
Troubleshooting Please refer to generic troubleshooting guide in the service guide database for information with respect to following items: •
Power-On Self-Test (POST)
•
POST Check Points
•
POST Error Messages List
•
Error Symptoms List
Chapter 4 ed from www.Manualslib.com manuals search engine
69
70 ed from www.Manualslib.com manuals search engine
Chapter 4
Chapter 5
Jumper and Connector Information Introduction to Connectors Main Board Placement 1
11
30 31 32
29
2 3 21 4
26
5 6
33 34
12 13 14
7 8
25
22
15
35
16 9
10
36
17
27 23
18 19 20
24
28
Component
#
Component
1
PS/2 CONN
2
HDMI CONN
3
LPT CONN
4
VGA CONN
5
1394 CONN
6
USB CONNS
7
LAN CONN
8
AUDIO CONNS
9
LAN CHIP
10
AUDIO CHIP
11
4 PIN POWER
12
SYSTEM FAN
13
U FAN
14
COM PORT
15
CLK GEN
16
PCIE 1X SLOT
ed from www.Manualslib.com manuals search engine
39 40
#
Chapter 5
37 38
41
71
17
PCIE 16X SLOT
18
PCI SLOTS
19
FRONT AUDIO HEADER
20
AUX_IN HEADER
21
U SOCKET
22
NORTH BRIDGE
23
1394 CHIP
24
FRONT 1394 HEADER
25
BATTERY
26
DIMM SLOTS
27
SOUTH BRIDGE
28
FRONT USB HEADER
29
SI/O CHIP
30
AS HEADER 2
31
AS HEADER 1
32
INTR HEADER
33
24 PIN POWER
34
FLOPPY CONN
35
IDE CONN
36
BIOS
37
CLR_CMOS HEADER
38
OBR HEADER
39
SPEAKER HEADER
40
SATA CONN
41
FRONT
72 ed from www.Manualslib.com manuals search engine
Chapter 5
Connectors USB Connectors 1394_USBX2(For 1394) Pin
Signal Name
Pin
Signal Name
1, 5
RUSB_VCC1
9
DCOUT_1394
2
USBD0-
11
TPB0-
3
USBD0+
12
TPB0+
4
Ground
13
TPA0-
6
USBD1-
14
TPA0+
7
USBD1+
15 - 22
IO_GND
8,10
Ground
LAN USB_2 Pin
Signal Name
Pin
Signal Name
1,5
RUSB_VCC2(5V)
13
MDI1-
2
SBD2-
14
MDI2+
3
SBD3-
15
MDI2-
4,8
GND
16
MDI3+
6
SBD2+
17
MDI3-
7
SBD3+
18
GND
23 - 30
Ground
19
LAN_LED
9
AVDDL_1D8V
20
LAN_LINK_LED
10
MDI0+
21
LED_100#
11
MDI0-
22
LED_1000#
12
MDI1+
Note: Pins 9-18 for RJ-45 LAN Jack pin definition, 19-22 for LAN LED definition.
Audio Backup Connectors AUDIO1F (Right Side /Light Blue in Color) Pin
Signal Name
61
GND
62
LINE1_L2
63
LINE1-JD
64
GND
65
LINE1_R5
Chapter 5 ed from www.Manualslib.com manuals search engine
73
AUDIO1E (Right Side /FRONT Lime in Color) Pin
Signal Name
51
GND
52
LINE_OUT_L2
53
FRONT-JD
54
GND
55
LINE_OUT_R5
AUDIO1D (Right Side /Pink in Color) Pin
Signal Name
41
GND
42
MIC1_L2
43
MIC1-JD
44
GND
45
MIC1_R5
AUDIO1A (Left Side/Gray in Color) Pin
Signal Name
1
GND
2
SIDESURRBACK_L2
3
SIDESURR-JD
4
GND
5
SIDESURRBACK_R2
AUDIO1C (Left Side, Orange in Color) Pin
Signal Name
31
GND
32
CEN-C
33
CEN-JD
34
GND
35
LFE-C
AUDIO1D (Left Side, Black in Color) Pin
Signal Name
21
GND
22
SURR_L
23
SURR-JD
24
GND
25
SURR_R
74 ed from www.Manualslib.com manuals search engine
Chapter 5
IDE/SATA 40-pin (2x20) PIDE Headers Pin
Signal Name
Pin
Signal Name
1
HD_RST#
2
Ground
3
PDD7
4
PDD8
5
PDD6
6
PDD9
7
PDD5
8
PDD10
9
PDD4
10
PDD11
11
PDD3
12
PDD12
13
PDD2
14
PDD13
15
PDD1
16
PDD14
17
IPDD0
18
PDD15
19
Ground
20
Key
21
PD_REQ
22
Ground
23
PD_IOW#
24
Ground
25
PD_IOR#
26
Ground
27
PD_RDY
28
Ground
29
PD_ACK#
30
Ground
31
IRQ14_R
32
N/C
33
PD_A1
34
PD_DET
35
PD_A0
36
PD_A2
37
PD_CS1#
38
PD_CS3#
39
IDE_LED#
40
Ground
1x7-pin SATA Headers Pin
Signal Name
1
GND
2
SATA_TX0+_C
3
SATA_TX0-_C
4
GND
5
SATA_RX0-_C
6
SATA_RX0+_C
7
GND
8
KEY
9
KEY
Chapter 5 ed from www.Manualslib.com manuals search engine
75
VGA Pin
Signal Name
Pin
Signal Name
1
CONN_RED
9
5V_DVI
2
CONN_GREEN
10
GND
3
CONN_BLUE
11
GND
4
GND
12
CONN_DAC_SDAT
5
GND
13
CONN_HSYNC#
6
GND
14
CONN_VSYNC#
7
GND
15
CONN_DAC_SCL
8
GND
HDMI Pin
Signal Name
Pin
Signal Name
1
HDMI_TXAP2
12
HDMI_TXCAN
2
GND
13
NC
3
HDMI_TXAN2
14
NC
4
HDMI_TXAP1
15
HDMI_DDC_CLK
5
GND
16
HDMI_DDC_DATA
6
HDMI_TXAN1
17
GND
7
HDMI_TXAP0
18
5V_S0
8
GND
19
HDMI_HOT_PLUG_DETECT
9
HDMI_TXAN0
20
GND
10
HDMI_TXCAP
21
GND
11
GND
76 ed from www.Manualslib.com manuals search engine
Chapter 5
Jumpers Jumper/Header Name
Function
Definition
UFAN (3 PIN)
U FAN HEADER
1: GND 2: POWER 3: SENSE
Yellow is symbol, Red is Pin1 of symbol SYSFAN (3 PIN)
SYSTEM FAN HEADER
1: GND 2: POWER 3: SENSE
Yellow is symbol, Red is Pin1 of symbol CLR_CMOS (3 PIN)
CLEAR CMOS HEADER
1,2: CLEAR CMOS (1: Ground, 2: RTC_RSTJ) 2,3: NORMAL (3: VCC_RTC)
Yellow is symbol, Red is Pin1 of symbol OBR
System Recover HEADER
1: SYS_RECOVER 2: GND
Yellow is symbol, Red is Pin1 of symbol
Chapter 5 ed from www.Manualslib.com manuals search engine
77
Jumper/Header Name
Function
Definition
F_USB1, F_USB2, F_USB3
FRONT USB HEADER (2x5)
1: VCC5 2: VCC5 3: D04: D15: D0+ 6: D1+ 7: GND 8: GND 9: KEY 10: GND
Yellow is symbol, Red is Pin1 of symbol
F_AUDIO1
FRONT AUDIO HEADER (2x5)
1: FMIC_L 2: GND 3: FMIC_R 4: 3D3V_S0 5: LINE_OUT_R 6: MIC_JD 7: FRONT-IO-SENSE 8: KEY 9: LINE_OUT_L 10: LINE_JD
Yellow is symbol, Red is Pin1 of symbol IR
IR
1: VCC5 2: KEY 3: IRRX 4: GND 5: IRTX
78 ed from www.Manualslib.com manuals search engine
Chapter 5
Jumper/Header Name
Function
Definition
F_1394_1
FRONT 1394 HEADER
1: TPA+ 2: TPA3: GND 4: GND 5: TPB+ 6: TPB7: POWER 8: POWER 9: KEY 10: GND
Yellow is symbol, Red is Pin1 of symbol FP
Front Header
1: FP_1(PU 5V_S0) 2: LEDP(PU 5V_S5) 3: SATA_LED_L 4: PMSLED(PU 5V_S5) 5: GND 6: SWITCH_ON* 7: FP_RESET*_FP 8: GND 9: FP_9(PU 5V_S0) 10: KEY 11: FP_11(PU 5V_S0) 12: FP_12(PU 5V_S5) 13: ODD_LED* 14: LAN_LED
Yellow is symbol, Red is Pin1 of symbol
Chapter 5 ed from www.Manualslib.com manuals search engine
79
Jumper/Header Name
Function
Definition
COM1, COM2
COM Port Header
1: NDCD 2: NSIN 3: NSOUT 4: NDTR 5: GND 6: NDSR 7: NRTS 8: NCTS 9: NRI 10: KEY
Yellow is symbol, Red is Pin1 of symbol
INTERNAL SPEAKER HEADER
AUDIO INTERNAL SPEAKER HEADER
1: MONO_L 2: GND 3: MONO_R 4: KEY 5: GND 6: GND 7: VCC3 8: VCC5
Yellow is symbol, Red is Pin1 of symbol
80 ed from www.Manualslib.com manuals search engine
Chapter 5
Jumper/Header Name
Function
Definition
TPM
TPM HEADER
1: LCKL 2: GND 3: LFRAMEn 4: KEY 5: LRESETn 6: NC 7: LAD3 8: LAD2 9: VDD (3.3V) 10: LAD1 11: LAD0 12: GND 13: NC 14: NC 15: NC 16: SERIRQ 17: GND
Yellow is symbol, Red is Pin1 of symbol
18: CLKRUNin 19: LPDn 20: NC
Chapter 5 ed from www.Manualslib.com manuals search engine
81
82 ed from www.Manualslib.com manuals search engine
Chapter 5
Chapter 6
FRU (Field Replaceable Unit) List This chapter offers the FRU (Field Replaceable Unit) list in global configuration of Angora AM5610 and AM3610 desktop. Refer to this chapter whenever ordering the parts to repair or for RMA (Return Merchandise Authorization). Please note that when ordering FRU parts, you should check the most up-to-date information available on your regional web or channel. For whatever reasons a part number is changed, it will NOT be noted on the printed service guide. For Acer authorized service providers, your Acer office may have a different part number code from those given in the FRU list of this printed service guide. You MUST use the local FRU list provided by your regional Acer office to order FRU parts for service. Note: To scrap or to return the defective parts, you should follow the local government ordinance or regulations on how to dispose them properly, or follow the rules set by your regional Acer office on how to return it.
Chapter 6 ed from www.Manualslib.com manuals search engine
83
Angora AM50 Exploded Diagram
Number
Description
Number
1
AM50 Bezel
10
Power Supply
2
AM50 USB
11
Fan
3
AM50 USB
12
PCI Bracket
4
FDD Lock Slide
13
Left Slide Door
5
CD ROM Lock Slide
14
Motherboard
6
Chassis
15
HDD
7
USB PCB ASM
16
3.5” Device
8
USB Shielding
17
CD ROM
9
Right Slide Door
18
HDD Lock Slide
84 ed from www.Manualslib.com manuals search engine
Description
Chapter 6
Angora AM30 Exploded Diagram
Number
Description
Number
Description
1
AM30 Main Bezel
11
Fan
2
3_25 Cover
12
PCI Bracket
3
5_25 Cover
13
Left Side Door
4
AM50 USB
14
Motherboard
5
AM50 USB
15
HDD
6
Chassis
16
3.5” Device
7
USB PCB ASM
17
CD ROM
8
USB Shielding
18
HDD Lock Slide
9
Right Side Door
19
FDD Lock Slide
10
Power Supply
20
CD ROM Lock Slide
Chapter 6 ed from www.Manualslib.com manuals search engine
85
Angora AM10 Exploded Diagram
Number
Description
1
AM10 Main Bezel
2 3
Number
Description
10
Power Supply
3_25 Cover
11
Fan
5_25 Cover
12
PCI Bracket
4
AM50 USB
13
Left Side Door
5
AM50 USB
14
Motherboard
6
FDD Lock Slide
15
HDD Lock Slide
7
CD ROM Lock Slide
16
HDD
8
Chassis
17
3.5” Device
9
Right Side Door
18
CD ROM
86 ed from www.Manualslib.com manuals search engine
Chapter 6
Service Guide
Service guide files and updates are available on the AIPG/CSD web; for more information, please refer to http://csd.acer.com.tw
PRINTED IN TAIWAN
ed from www.Manualslib.com manuals search engine
Revision History Please refer to the table below for the updates made on Angora AM50, AM30, and AM10 service guide. Date
ed from www.Manualslib.com manuals search engine
Chapter
Updates
Copyright Copyright © 2007 by Acer Incorporated. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of Acer Incorporated.
Disclaimer The information in this guide is subject to change without notice. Acer Incorporated makes no representations or warranties, either expressed or implied, with respect to the contents hereof and specifically disclaims any warranties of merchantability or fitness for any particular purpose. Any Acer Incorporated software described in this manual is sold or licensed "as is". Should the programs prove defective following their purchase, the buyer (and not Acer Incorporated, its distributor, or its dealer) assumes the entire cost of all necessary servicing, repair, and any incidental or consequential damages resulting from any defect in the software.
Acer is a ed trademark of Acer Corporation. Intel is a ed trademark of Intel Corporation. Pentium 4 and Celeron are trademarks of Intel Corporation. Other brand and product names are trademarks and/or ed trademarks of their respective holders.
ed from www.Manualslib.com manuals search engine
Conventions The following conventions are used in this manual: SCREEN MESSAGES
Denotes actual messages that appear on screen.
NOTE
Gives bits and pieces of additional information related to the current topic.
WARNING
Alerts you to any damage that might result from doing or not doing specific actions.
CAUTION
Gives precautionary measures to avoid possible hardware or software problems.
IMPORTANT
Reminds you to do specific actions relevant to the accomplishment of procedures.
ed from www.Manualslib.com manuals search engine
Preface Before using this information and the product it s, please read the following general information. 1. This Service Guide provides you with all technical information relating to the BASIC CONFIGURATION decided for Acer's "global" product offering. To better fit local market requirements and enhance product competitiveness, your regional office MAY have decided to extend the functionality of a machine (e.g. add-on card, modem, or extra memory capability). These LOCALIZED FEATURES will NOT be covered in this generic service guide. In such cases, please your regional offices or the responsible personnel/channel to provide you with further technical details. 2. Please note WHEN ORDERING FRU PARTS, that you should check the most up-to-date information available on your regional web or channel. If, for whatever reason, a part number change is made, it will not be noted in the printed Service Guide. For ACER-AUTHORIZED SERVICE PROVIDERS, your Acer office may have a DIFFERENT part number code to those given in the FRU list of this printed Service Guide. You MUST use the list provided by your regional Acer office to order FRU parts for repair and service of customer machines.
ed from www.Manualslib.com manuals search engine
ed from www.Manualslib.com manuals search engine
Table of Contents System Specification
1
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Processor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 System Chipset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Onboard Graphics Solution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 HDMI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 PCI Express/PCI Slots . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Floppy Disk Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 SATA Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 LAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 USB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 1394a . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Buzzer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Front I/O Header . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 CIR & IR Blaster . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Onboard Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 Angora AM50 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 Front . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 Rear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 Angora AM30 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 Front . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 Rear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 Angora AM10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 Front . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 Rear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10 Acer Empowering Technology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11 Empowering Technology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11 Acer eRecovery Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11 Acer eDataSecurity Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12 Acer ePerformance Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14 Acer eRecovery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15 Create Backup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15 Restore from Backup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15 Create Factory Default Image CD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15 Re-install Bundled Software without CD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15 Change . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16 Acer Disc-to-Disc Recovery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17 Restore without a Recovery CD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17 Multilingual Operating System Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17 Hardware Specification and Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18 Processor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18 System Main Chipset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18 North Bridge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18 South Bridge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19 Wake-up Event Specification (Default Setting in BIOS) . . . . . . . . . . . . . . . . . . .19 Front LED States . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20 System Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20 Super I/O . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
i ed from www.Manualslib.com manuals search engine
USB Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20 Audio Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21 1394 Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21 Hardware Monitor Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21 BIOS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22 BIOS Hotkey List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22 Environment Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22 Power Management Function (AI Function) . . . . . . . . . . . . . . . . . . . . . . .23 Device Standby Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23 Global Standby Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23 Suspend Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23 AI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
Setup Utility
25
About the Setup Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25 Control Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25 Entering the Setup Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26 Product Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27 Standard CMOS Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28 Date and Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28 SATA Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28 Drive A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28 Halt On . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28 Base Memory, Extended Memory, and Total Memory . . . . . . . . . . . . . . . . . . . .28 Advanced BIOS Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29 Virus Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29 U Internal Cache/External Cache . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29 Quick Power On Self Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30 First / Second / Third Boot Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30 Boot Other Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30 Boot Up Floppy Seek . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30 Boot Up NumLock Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30 Gate A20 Option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30 Typematic Rate Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30 Security Option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30 APIC Mode 30 MPS Version Control For OS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30 OS Select for DRAM > 64 MB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30 HDD S.M.A.R.T Capability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31 Silent Boot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31 Small Logo (EPA) Show . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31 Configuration Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31 Bootblock Write Protect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31 Hard Disk Boot Priority . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32 Advanced Chipset Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33 UMA Frame Buffer Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33 Memory Hole . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33 System BIOS Cacheable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33 Integrated Peripherals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34 South OnChip IDE Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34 South OnChip PCI Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34 Super IO Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34 Init Display First . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34 South OnChip IDE Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35 IDE DMA Transfer Access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35 ii ed from www.Manualslib.com manuals search engine
OnChip IDE Channel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35 IDE Primary/Secondary Master/Slave PIO . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35 IDE Primary/Secondary Master/Slave UltrA . . . . . . . . . . . . . . . . . . . . . . . .35 IDE HDD Block Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35 South OnChip PCI Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36 ATI Azalia Audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36 ATI SATA Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36 ATI SATA Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36 USB EHCI Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36 OnChip USB Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37 OnChip USB KBC Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37 USB Mouse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37 Onboard LAN Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37 Onboard Lan Boot ROM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37 Onboard 1394 Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37 Super IO Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38 Onboard FDC Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38 Onboard Serial Port 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38 Onboard Serial Port 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38 UART Mode Select . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38 UR2 Duplex Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38 Onboard Parallel Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39 Parallel Port Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39 E Mode Use DMA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39 Power Management Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40 AI Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40 AI Suspend Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40 CS2 Disable/Enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41 Power Management Option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41 Video Off Option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41 Video Off Method . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41 Soft-Off by PWRBTN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41 Power On By PCI Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41 USB Wakeup From S1/S2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41 USB Wakeup From S4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41 PS2 KB/MS Wakeup From S1/S2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41 Wakeup By LAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41 HPET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41 PWRON After PWR-Fail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41 RTC Alarm Resume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42 PnP/PCI Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43 Reset Configuration Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43 Resources Controlled By . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43 PCI/VGA Palette Snoop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43 Assign IRQ For VGA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43 Assign IRQ for USB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44 PCI Latency Timer (CLK) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44 Maximum Payload Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44 PC Health Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45 U Shut Down Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45 Frequency & Voltage Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47 Spread Spectrum . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47 SB600 Spread Spectrum . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47 Load Optimized Defaults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48 Set Supervisor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49 iii ed from www.Manualslib.com manuals search engine
Enter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49 Save and Exit Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50 Exit without Saving . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51
Machine Disassembly and Replacement
53
General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53 Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53 Angora AM50/30/10 Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54 Disassembly Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54 Reassembly Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61
Troubleshooting
69
Jumper and Connector Information
71
Introduction to Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71 Main Board Placement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71 Connectors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .73 Jumpers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .77
FRU (Field Replaceable Unit) List
83
Angora AM50 Exploded Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .84 Angora AM30 Exploded Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .85 Angora AM10 Exploded Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .86
iv ed from www.Manualslib.com manuals search engine
Chapter 1
System Specification Overview Size •
240x240mm (9.6"x9.6") 4 Layers
Processor •
Socket type: AMD AM2 socket
•
Socket quantity: one
•
Processor type: Sempron-D, Athlon64, Athlon64+
System Chipset •
North bridge: ATI RS690
•
South bridge: ATI SB600
•
Super I/O: ITE8718F with Hardware monitor
Memory •
Dual Channel DDR2 667/533/400,Unbuffered DIMM
•
4 DDRII DIMM (8 GB Maximum capacity)
Onboard Graphics Solution •
ATI RS690 on-die graphic solution (ATI Radeon® X700-based graphic core) •
ATI AVIVO technology
•
Multiple display features
•
One D-Sub VGA port on the rear side
•
One HDMI port on the rear side (A14)
•
SDVO interface which s hot plug detection
HDMI •
With HD solution
•
Meets HDMI 1.2a specification
PCI Express/PCI Slots •
One PCI Express x16 slot
•
One PCI Express x1 slot
•
Two PCI slots
Floppy Disk Drive •
One slot, 1.44MB/3 mode 3.5” devices
SATA Interface •
Two separate controllers with integrated SATA 2 (Gen1 and Gen2) PHYs
•
Each controller s two drives in master mode for a total of four
Chapter 1 ed from www.Manualslib.com manuals search engine
1
•
Compliant with ATA/ATAPI-7 Volume 3 Serial ATA standards
•
High speed, low voltage, low pin count
•
Each controller s dual channel SATA 2
•
3.0 Gb/s per direction per channel
•
s power-down capabilities
Audio •
Realtek ALC888-GR, colay with ALC883
LAN •
Marvell 88E8056, Gb PHY featuring: •
10/100/1000BASE-T IEEE 802.3 compliant
•
Two-Wire Serial Interface (TWSI) for VPD
•
2.5GHz Signaling,x1 link width, width strapped on reset
•
of up to eight outstanding NP requests as a master
USB •
X10 USB2.0/1.1(Rear 4 ports, Front 6ports)
1394a •
1394 header x 1 and Back I/O *1 (TSB43AB23PDTG4 2-port)
Buzzer •
One onboard buzzer
Front I/O Header
CIR & IR Blaster •
Compliant to ITE’s pin definition to CIR & IR blaster function for Vista home SKU
•
Power-up feature
Onboard Connectors •
Rear I/O connectors: •
VGA port
•
Dual stack USB ports with 1394 connector
2 ed from www.Manualslib.com manuals search engine
Chapter 1
•
•
Dual Stack USB ports with RJ-45 connector
•
Vertical Audio connector with 6 JACKS
•
DVI-I port
•
HDMI port
•
PS2 port
•
Print port
Onboard connectors: •
One U socket
•
Four DDR2 memory sockets
•
One PCI Express x16 slot
•
One PCI Express x1 slot
•
Two PCI slots
•
One FDD slot
•
One PATA slot
•
Four SATAII IDE connectors
•
Three 2*5 pin USB headers, compliant to Intel FPIO standard specification
•
One 2*5 pin front audio header, compliant to Intel FPIO standard specification
•
One 2*5 pin serial port connector
•
One 1*4 pin AUX-In connector
•
One 4-pin U fan connector
•
One 3-pin system fan connector with linear circuit
•
One 24-pin + 4-pin ATX interface PS3/PS2 SPS connector
•
One 2*7 pin front I/O header
•
One 2*5 pin 1394 header
Chapter 1 ed from www.Manualslib.com manuals search engine
3
Block Diagram
4 ed from www.Manualslib.com manuals search engine
Chapter 1
Angora AM50 Front
#
Chapter 1 ed from www.Manualslib.com manuals search engine
Description
1
ODD Door
2
Slide Door
3
LAN LED
4
HDD LED
5
Power Button
6
USB Port
7
MIC Phone
8
Speaker Out
5
Rear
#
Description
#
Description
1
6 audio jacks (7.1 HD audio jack)
8
PS/2 Keyboard
2
LAN Port
9
PS/2 Mouse
3
USB Ports
10
Power Cable Port
4
1394 Port
11
SPDIF Bracket
5
CRT/LCD Port
12
SPDIF Port
6
Parallel Port
13
Recovery Switch Holder
7
HDMI Port
14
Lock Handle
6 ed from www.Manualslib.com manuals search engine
Chapter 1
Angora AM30 Front
#
Chapter 1 ed from www.Manualslib.com manuals search engine
Description
1
Optical Device
2
3.5” Device
3
LAN LED
4
HDD LED
5
Power Button
6
USB Port
7
MIC Phone
8
Speaker Out
7
Rear
#
Description
#
Description
1
6 audio jacks (7.1 HD audio jack)
8
PS/2 Keyboard
2
LAN Port
9
PS/2 Mouse
3
USB Ports
10
Power Cable Port
4
1394 Port
11
SPDIF Bracket
5
CRT/LCD Port
12
SPDIF Port
6
Parallel Port
13
Recovery Switch Holder
7
HDMI Port
14
Lock Handle
8 ed from www.Manualslib.com manuals search engine
Chapter 1
Angora AM10 Front
#
Chapter 1 ed from www.Manualslib.com manuals search engine
Description 1
Optical Device
2
3.5” Device
3
Power Button
4
HDD LED
5
LAN LED
6
Speaker Out
7
MIC Phone
8
USB Port
9
Rear
#
Description
#
Description
1
6 audio jacks (7.1 HD audio jack)
8
PS/2 Keyboard
2
LAN Port
9
PS/2 Mouse
3
USB Ports
10
Power Cable Port
4
1394 Port
11
SPDIF Bracket
5
CRT/LCD Port
12
SPDIF Port
6
Parallel Port
13
Recovery Switch Holder
7
HDMI Port
14
Lock Handle
10 ed from www.Manualslib.com manuals search engine
Chapter 1
Acer Empowering Technology Acer’s innovative Empowering Technology makes it easy for you to access frequently used functions and manage your new Acer notebook. It features the following handy utilities: •
Acer eRecovery Management backs up and recovers data flexibly, reliably and completely.
•
Acer eDataSecurity Management protects data with s and advanced encryption algorithms.
•
Acer ePerformance Management improves system performance by optimizing disk space, memory and registry settings.
For more information, press the key to launch the Empowering Technology menu, then click on the appropriate utility and select the Help or Tutorial function.
Empowering Technology Before using Acer eRecovery Management, you must initialize the Empowering Technology . Right click on the Empowering Technology toolbar and select Setup to do so. If you do not initialize the Empowering Technology , you will be prompted to do so when running Acer eRecovery Management for the first time.
Acer eRecovery Management Acer eRecovery Management is a powerful utility that does away with the need for recovery disks provided by the manufacturer. The Acer eRecovery Management utility s Microsoft Windows XP Home Service Pack 2, Microsoft Windows XP Media Center Edition Wallop 2, Microsoft Windows Vista Home Basic, , Business, and Ultimate. The Acer eRecovery Management utility occupies space in a hidden partition on your system’s HDD. -created backups are stored on D:\ drive. Acer eRecovery Management provides you with: •
protection
•
Recovery of applications and drivers
•
Image/data backup:
•
•
Back up to HDD (set recovery point)
•
Back up to CD/DVD
Image/data recovery tools •
Recovery from a hidden partition (factory defaults)
•
Recovery from the HDD (most recent -defined recovery point)
•
Recovery from CD/DVD
Chapter 1 ed from www.Manualslib.com manuals search engine
11
For more information, please refer to Acer eRecovery Management. Note: If your computer does not come with a Recovery CD or System CD, please use Acer eRecovery Management’s System backup to optical disk feature to burn a backup image to CD or DVD. To ensure the best results when you recover a system by using a CD or Acer eRecovery Management, detach all peripherals (except the external Acer ODD, if your computer has one), including your Acer ezDock.
Acer eDataSecurity Management Acer eDataSecurity Management is a handy file encryption utility that protects your files from being accessed by unauthorized persons. It is conveniently integrated with Windows explorer as a shell extension for quick and easy data encryption/decryption and also s on-the-fly file encryption for MSN Messenger and Microsoft Outlook. Note: The Acer eDataSecurity Management setup wizard will prompt you for a supervisor and default encryption. This encryption will be used to encrypt files by default, or you can choose to enter your won file-specific when encrypting a file. Note: The used to encrypt a file is the unique key that the system needs to decrypt it. If you lose the , the supervisor is the only other key capable of decrypting the file. If you lose both s, there will be no way to decrypt your encrypted file. Be sure to safeguard all related s!
12 ed from www.Manualslib.com manuals search engine
Chapter 1
Chapter 1 ed from www.Manualslib.com manuals search engine
13
Acer ePerformance Management Acer ePerformance Management is a system optimization tool that boosts the performance of your Acer notebook. It provides and expresses optimization method to release unused memory and disk space quickly. The can also enable advanced options for full control over the following option: •
Memory optimization: to releases unused memory and check usage
•
Disk optimization: to remove unneeded items and files
•
Speed optimization: to improve the usability and performance of your Windows XP system
For more information, please refer to Acer eRecovery Management. Note: If your computer does not come with a Recovery CD or System CD, please use Acer eRecovery Management’s System backup to optical disk feature to burn a backup image to CD or DVD. To ensure the best results when recovering your system using a CD or Acer eRecovery Management, detach all peripherals (except the external Acer ODD, if your computer has one), including your Acer ezDock.
14 ed from www.Manualslib.com manuals search engine
Chapter 1
Acer eRecovery Acer eRecovery is a tool to quickly backup and restore the system. s can create and save a backup of the current system configuration to hard drive, CD, or DVD. Acer eRecovery consists of the following functions: 1. Create backup 2. Restore from backup 3. Create factory default image CD 4. Re-install bundled software without CD 5. Change Acer eRecovery
Create Backup s can create and save backup images to hard drive, CD, or DVD. Please follow the steps below to create backup. 1. Boot to Windows XP. 2. Press
Use Backup to HDD to store the backup disc image on drive D:\
•
Backup to optical device to store the backup disc image on CD or DVD. This option is only available on systems that include an optical disc burner.
7. After choosing the backup method, click Next. Then follow the instruction on the screen to complete the process.
Restore from Backup s can restore backup previously created (as stated in the Create Backup section) from hard drive, CD, or DVD. Please follow the steps below to restore from backup. 1. Boot to Windows XP. 2. Press
Create Factory Default Image CD When the System CD and Recovery CD are not available, you can create them by using this feature. Please follow the steps below to create factory default image CD. 1. Boot to Windows XP. 2. Press
Re-install Bundled Software without CD Acer eRecovery stores pre-loaded software internally for easy driver and application re-installation. 1. Boot Windows XP. 2. Press
15
3. Enter the to proceed. The default is six zeros. 4. In the Acer eRecovery window, select Recovery actions and Next. 5. In the Recovery settings window, select Re-install applications / drivers and click Next. 6. Select the desired driver / application and follow the instructions on screen to re-install. After the first launch, Acer eRecovery prepared all the needed software and may take few seconds to bring up the software content window.
Change Acer eRecovery and Acer disc-to-disc recovery are protected by a that can be changed by s. Follow the steps below to change the in Acer eRecovery. 1. Boot to Window XP. 2. Press
16 ed from www.Manualslib.com manuals search engine
Chapter 1
Acer Disc-to-Disc Recovery Restore without a Recovery CD This recovery process helps you restore the C:\ drive with the original software content that is installed when you purchase your system. Follow the steps below to rebuild your C:\ drive. Note: The C:\ drive will be reformatted and all data will be erased. It is important to back up all data files before you use this option. 1. Restart the system. 2. While the Acer logo comes out, press
Multilingual Operating System Installation Follow the instructions to choose the operating system and language you prefer when you first power on the system. 1. Turn on the system. 2. Acer’s multilingual operating system selection menu will pop up automatically. 3. Use the arrow keys to scroll to the language version you want. Press <Enter> to confirm your selection. 4. The operating system and language you choose now will be the only option for future recovery operations. 5. The system will install the operating system and language you choose.
Chapter 1 ed from www.Manualslib.com manuals search engine
17
Hardware Specification and Configuration Processor Item
Specification
Type
Sempron-D, Athlon64, Athlon64+ (for desktop U information in detail, please refer to http://www.intel.com/products/desktop/processors/ index.htm?iid=process+desktop)
System Main Chipset Item
Specification
Core logic
ATI RS690 + ATI SB600
Super I/O controller
ITE8718F with Hardware monitor
LAN controller
Marvell 88E8056, Gb PHY
Memory controller
ATI RS690
1394 controller
1394 header x 1 and Back I/O *1 (TSB43AB23PDTG4 2-port)
Serial ATA
Independent DMA operation on 4 ports, Data transfer rates up to 3.0Gbps
Audio subsystem controller
Realtek ALC888-GR, colay with ALC883
VGA controller
ATI RS690
North Bridge Item
Specification
General information
ATI RS690 s Core 2 Duo processors, DDR2 and DDR3 memory, and its graphics subsystem features a new graphics core twice as fast as the older Radeon Xpress 200.
Feature
• • • • • • • • • • •
Integrated a DirectX 9.0 compliant 2D/3D graphics core Integrated an ATI Radeon X700-based graphics engine s LDTSTP interface, U throttling, and stutter mode The RS690 incorporates ATI’s innovative Avivo™ display architecture A new TV encoder, based on design used in ATI’s Xilleon™ products RS690`s SURROUNDVIEW TM up to three independent monitors Integrated 400 MHz DAC for external desktop displays Primary HyperTransport link up to 1.0 GHz to the U One x4 A-link Express II interface (PCI Express 1.1 compliant) PCI Express 16 lane link interface for external graphics processors Dual PCI Express single lane link interface, with dedicated controller for other peripherals • Active power management, s ATI PowerOnDemand™ • 465-FCBGA package 21 mm × 21 mm
18 ed from www.Manualslib.com manuals search engine
Chapter 1
South Bridge Item
Specification
Chipset
ATI SB600
Feature
A-Link Express II interface to the RADEON IGPs: • 1/2/4-lane A-link Express II interface • Dynamic detection of lane configuration PCI Host Bus Controller: • PCI Rev. 2.3 specification • PCI Bus at 33MHz • up to 6 bus master device • 40-bit addressing USB Controller: • 5 OHCI and 1 EHCI Host controller to 10 USB ports • All10 ports are USB 1.1("Low speed", "Full speed") and 2.0("High speed") compatible • AI S1~S5 SMBus Controller: • SMBus Rev. 2.0 compliant • SMBALERT# signal/GPIO DMA Controller: • 2 cascaded 8237 DMA controllers • PC/PCI DMA • LPC DMA • type F DMA
Wake-up Event Specification (Default Setting in BIOS) S1
S3
S4
S5
Power button
Enable (default), Disabled
Enabled (default), Disabled
Enabled (default), Disabled
Enabled (default), Disabled
PS2 keyboard
Enabled, Disabled (default)
Enabled, Disabled (default)
N/A
N/A
USB keyboard
Enabled (default), Disabled
Enabled (default), Disabled
Enabled (default) Disabled
N/A
PME
Enabled (default), Disabled
Enabled (default), Disabled
Enabled (default), Disabled
Enabled (default), Disabled
Modem (ring)
Enabled, Disabled (default)
Enabled, Disabled (default)
Enabled, Disabled (default)
Enabled, Disabled (default)
RTC
Enabled, Disabled (default)
Enabled, Disabled (default)
Enabled, Disabled (default)
Enabled, Disabled (default)
Chapter 1 ed from www.Manualslib.com manuals search engine
19
Front LED States State for a Single Color Power LED (Blue) LED State
Description
AI State
Steady Blue
Running
S0
Blinking Blue
Sleeping
S1, S3
Off
Power Off
S4, S5
State for LAN LED (Blue) LED State
Description
Controller State
Blinking blue
Active
Active
Off
Idle
Idle
State for a Single Color Storage LED (Blue) LED State
Description
Controller State
Blinking blue
Active
Active
Off
Idle
Idle
System Memory Item
Specification
Feature
• Dual Channel DDR2 667/533/400, Unbuffered DIMM • 4 DDRII DIMM (8 GB Maximum capacity)
Super I/O Item
Description
Chip
ITE IT8718F
Feature
• • • • • • • •
Meet LPC Spec 1.1 Compliant with Microsoft PC98/PC2001 Hardware Design Guide PS/2 Keyboard & Mouse up to four 3.5-inch or 5.25-inch floppy disk drives two serial ports, one EPP/E parallel port three fans (5 fan speed monitoring inputs) IrDA 1.0 FIR protocol with maximum baud rate up to 115.2K bps Hardware Monitor ed (External Thermal Sensor Host )
USB Interface Item
Description
Chip
ATI SB600
Feature
• • • •
10 USB 2.0/1.1 ports Dual stack with RJ-45 back connector Dual stack with 1394 back connector 2 header ing 4 USB ports for front cabling and 1 header optional
20 ed from www.Manualslib.com manuals search engine
Chapter 1
Audio Interface Item
Description
Chip
Realtek ALC888 (high definition audio)
Feature
• High-performance DACs with 95dB SNR (A-Weighting), ADCs with 85dB SNR (A-Weighting) • Meets performance requirements for audio on PC2001 systems and Microsoft WLP 2.x • Ten DAC channels 16/20/24-bit PCM format, for 7.1 sound playback, plus 2 channels of independent stereo sound output through the front output. • 2 stereo ADCs 16/20/24-bit PCM format, one for stereo microphone, one for legacy mixer recording. • All DACs s 44.1K/48K/96K/192kHz sample rate • All ADCs 44.1K/48K/96K sample rate • 16/20/24-bit S/PDIF-OUT s 44.1K/48K/96K/192kHz sample rate • 16/20/24-bit S/PDIF-IN s 44.1K/48K/96K sample rate
1394 Interface Item
Description
Chip
TSB43AB23PDTG4
Feature
• Compliant with the IEEE 1394-1995 Release 1.0 and IEEE 1394a P2000 specifications with full 1394a P2000 • Compliant with the PCI V2.2 specification and card bus interfaces • Three 1394a ports enable connections at 100/200/400Mbps • Equipped with an OHCI compliant programming interface and I2C EEPROMs or four-wire serial ROMs
Hardware Monitor Function Item
Description
Feature
• Built-in 8-bit Analog to Digital Converter • 3 thermal inputs from remote thermal resistor or thermal diode or diodeconnected transistor • Provides VID0-VID7 for U Vcore identification • 8 voltage monitor inputs (VBAT is measured internally) • Watch dog comparison of all monitored values
Chapter 1 ed from www.Manualslib.com manuals search engine
21
BIOS Item
Description
BIOS code programmer
Phoenix Award
Version
Phoenix BIOS 6.00 PC
Feature
• ROM type: flash ROM • ROM size: 4MB • Protocol ed: PCIX 1.0, PCI 2.2, APM 1.2, VESA/DPMS (VBE/PM V1.1), SMBIOS 2.3, E-IDE 1.1, AI 1.0b, ESCD 1.03, PnP 1.0a, Bootable CD-ROM 1.0 • Boot from CD-ROM feature: yes • LS-120 FDD drive : yes • BIOS boot block feature: yes • s Microsoft SLP 2.0 for Windows Vista
Note: The BIOS can be overwritten/upgraded by using the flash utility.
BIOS Hotkey List Hotkey
Description
DEL
To enter BIOS Setup Utility: press the DEL key while the system is booting to enter BIOS Setup Utility.
Environment Requirements Item
Specification
Temperature Operating
+5OC ~ +35OC
Non-operating
-20OC ~ +60OC (storage packed), -10OC ~ +60OC (unpacked)
Humidity Operating
15% to 80% RH, non-condensing
Non-operating
10% to 90% RH, non-condensing at 40oC
Vibration Operating
5 ~ 500Hz, 2.20g RMS random, 10 minutes per axis in all three axes
Non-operating
5 ~ 500Hz, 1.09g RMS random, one hour per axis in all three axes
22 ed from www.Manualslib.com manuals search engine
Chapter 1
Power Management Function (AI Function) Device Standby Mode •
Independent power management timer for hard disk drive devices (zero to 15 minutes, time step = one minute).
•
Hard disk drive goes into Standby mode (for ATA standard interface).
•
Disable V-sync to control the VESA DPMS monitor.
•
Resume method: device activated (keyboard for DOS, keyboard & mouse for Windows).
•
Resume recovery time: three to five seconds.
Global Standby Mode •
Global power management timer (two to 120 minutes, time step = 10 minutes).
•
Hard disk drive goes into Standby mode (for ATA standard interface).
•
Disable H-sync and V-sync signals to control the VESA DPMS monitor.
•
Resume method: return to original state by pushing external switch button, modem ring in, keyboard and mouse for APM mode.
•
Resume recovery time: seven to 10 seconds.
Suspend Mode •
Independent power management timer (two to 120 minutes, time step = 10 minutes) or pushing external switch button.
•
U goes into SMM.
•
U asserts STPCLK# and goes into the Stop Grant state.
•
LED on the turns amber color.
•
Hard disk drive goes into SLEEP mode (for ATA standard interface).
•
Disable H-sync and V-sync signals to control the VESA DPMS monitor.
•
Ultra I/O and VGA chip go into power saving mode.
•
Resume method: return to original state by pushing external switch button, modem ring in, keyboard and mouse for APM mode.
•
Return to original state by pushing external switch button, modem ring in and USB keyboard for AI mode.
AI •
AI specification 1.0b
•
S0, S1, S3 and S5 sleep state
•
Onboard device power management
•
Onboard device configuration
Chapter 1 ed from www.Manualslib.com manuals search engine
23
24 ed from www.Manualslib.com manuals search engine
Chapter 1
Chapter 2
Setup Utility About the Setup Utility The computer uses the Phoenix Award BIOS (Basic Input and Output System) with for Windows Plug and Play. The CMOS chip on the main board contains the ROM setup instructions for configuring the main board BIOS. The BIOS Setup Utility displays the system’s configuration status and provides you with options to set system parameters. The parameters are stored in Battery-backed-up CMOS RAM that saves this information when the power is turned off. When the system is turned back on, the system is configured with the values you have stored in CMOS. The BIOS Setup Utility enables you to configure: •
Hard drives, diskette drives and peripherals
•
Video display type and display options
•
protection from unauthorized use
•
Power management features
The settings made in the Setup Utility affect how the computer performs. Before using the Setup Utility, ensure that you understand the Setup Utility options. This Setup Utility should be used: •
when changing the system configuration
•
when a configuration error is detected and you are prompted to make changes to the Setup Utility
•
when trying to resolve IRQ conflicts
•
when making changes to the Power Management configuration
•
when changing the or making other changes to the Security Setup
Control Keys Item
Description
IKLJ
Move to the item you want to select
ENTER
Select the item you want or enter the sub-menu
ESC
Retreat from the current page
Pg Up
Increase the numeric value or make changes
Pg Dn
Decrease the numeric value or make changes
F1
General help
F5
Restore the previous CMOS value from CMOS
F7
Load the factory default setting
F10
Save all the CMOS changes
Exit
Leave the Setup Utility
Chapter 2 ed from www.Manualslib.com manuals search engine
25
Entering the Setup Utility Power on the computer and the system will start POST (Power On Self Test). When the message Press DEL to enter SETUP appears on the screen, press the DEL key to enter the setup menu. Once you enter the Phoenix Award BIOS CMOS Setup Utility, the main menu will appear on the screen. Use arrow keys to select the item you want and press ENTER to confirm the setting or enter the sub-menu.
Phoenix - Award WorkstationBIOS CMOS Setup Utility XProduct Information
XPC Health Status
XStandard CMOS Features
XFrequency/Voltage Control
XAdvanced BIOS Features
Load Optimized Defaults
XAdvanced Chipset Features
Set Supervisor
XIntegrated Peripherals
Set
XPower Management Setup
Save & Exit Setup
XPnP/PCI Configuration
Exit Without Saving
KLIJ :Move Enter: Select +/-/ :Value F10:Save ESC:Exit F1:General Help F9:Optimized Defaults Standard CMOS setup for changing time, date, hard disk type, etc.
26 ed from www.Manualslib.com manuals search engine
Chapter 2
Product Information This page displays product information about your system. You can press ESC to return to the main menu setting page.
Phoenix - Award WorkstationBIOS CMOS Setup Utility Product Information Product Name
Aspire M5188
System S/N Mainboard ID
F690CVM
Help Item Menu Level
X
Asset Tag Number System BIOS Version
6.00PC
SMBIOS Version
2.4
System BIOS ID
721A1D04
BIOS Release Date
03/17/2007
KLIJ :Move Enter: Select +/-/PU/PD :Value F10: Save and Exit ESC:Exit F1: General Help
Chapter 2 ed from www.Manualslib.com manuals search engine
F5: Previous Values
F7: Optimized Defaults
27
Standard CMOS Features This page displays the standard CMOS features. You can press ESC to return to the main menu setting page.
Phoenix - Award WorkstationBIOS CMOS Setup Utility Standard CMOS Features Date (mm:dd:yy)
Thu, Apr 12 2007
Time (hh:mm:ss)
10 : 32 : 39
Help Item Menu Level
X
XIDE Channel 0 Master
[None]
Change the day, month,
XIDE Channel 0 Slave
[None]
year and century.
XIDE Channel 2 Master
[None]
XIDE Channel 2 Slave
[None]
XIDE Channel 3 Master
[None]
XIDE Channel 3 Slave
[None]
Drive A
None
Halt On
[All, But Keyboard]
Base Memory
640K
Extended Memory
1833984K
Total Memory
1835008K
KLIJ :Move Enter: Select +/-/PU/PD :Value F10: Save and Exit ESC:Exit F1: General Help
F5: Previous Values
F7: Optimized Defaults
Date and Time The Date and Time items show the current date and time set on the computer. If you are running a Windows OS, these items are automatically updated whenever you make changes to the Windows Date and Time Properties utility.
SATA Devices This main board features four SATA connectors ing four SATA drives. SATA refers to Serial ATA (Advanced Technology Attachment), the standard interface for the IDE hard drives which are currently used in most PCs.
Drive A This item will identify the type of floppy disk drive A that has been installed.
Halt On This item determines whether the system stops or not if an error occurs during system boot-up. At defaults All, But Keyboard, the boot will be interrupted for all errors except a keyboard error.
Base Memory, Extended Memory, and Total Memory These items are automatically detected by the system at start-up time. You can not make changes to these fields.
28 ed from www.Manualslib.com manuals search engine
Chapter 2
Advanced BIOS Features This page displays advanced BIOS features. You can press ESC to return to the main menu setting page.
Phoenix - Award WorkstationBIOS CMOS Setup Utility Advanced BIOS Features XHard Disk Boot Priority
[Press Enter]
Virus Warning
[Disabled]
U Internal Cache
[Enabled]
External Cache
[Enabled]
Quick Power On Self Test
[Enabled]
First Boot Device
[Hard Disk]
Second Boot Device
[CDROM]
Third Boot Device
[Disabled]
Boot Other Device
[Enabled]
Boot Up Floppy Seek
[Disabled]
Boot Up Num Lock Status
[On]
Gate A20 Option
[Fast]
Typematic Rate Setting
[Disabled]
X Typematic Rate (chars/sec)
6
X Typematic Delay (Msec)
250
Security Option
[Setup]
APIC Mode
Enabled
MPS Version Control For OS
[1.4]
OS Select For DRAM > 64MB
[Non-OS2]
HDD S.M.A.R.T. Capability
[Disabled]
Silent Boot
[Enabled]
Small Logo (EPA) Show
[Disabled]
Configuration Table
[Disabled]
Bootblock Write Protect
[Enabled]
Help Item Menu Level
X
KLIJ :Move Enter: Select +/-/PU/PD :Value F10: Save and Exit ESC:Exit F1: General Help
F5: Previous Values
F7: Optimized Defaults
Virus Warning This item enables or disables the boot sector virus protection.
U Internal Cache/External Cache Cache memory is additional memory that is much faster than conventional DRAM (system memory). Us from 486-type on up contain internal cache memory, and most, but not all, modern PCs have additional (external) cache memory. When the U requests data, the system transfers the requested data from the main DRAM into cache Chapter 2 ed from www.Manualslib.com manuals search engine
29
memory, for even faster access by the U. Disabling the Internal/External Caching may affect processing speeds.
Quick Power On Self Test Use this item to shorten the POST and have the system startup faster. You might like to enable this item after you are confident that your system hardware is operating smoothly.
First / Second / Third Boot Device Use this three items to select the priority and order of the devices that your system searches for an operating system when the system is powering on.
Boot Other Device When enabled, the system searches all other possible locations for an operating system if it fails to find one in the devices specified under the First, Second, and Third boot devices.
Boot Up Floppy Seek This item controls whether the BIOS checks for a floppy drive while booting up.
Boot Up NumLock Status This item defines if the keyboard NumLock key is active when your system is booted.
Gate A20 Option This item defines how the system handles legacy software that was written for an earlier generation of processors. Set this item for the default value.
Typematic Rate Setting If this item is enabled, you can use the following two items to set the Typematic Rate and the Typematic Delay settings for the keyboard. The default setting is
Typematic Rate (Chars/Sec): Use this item to define how many characters per second are generated by a held-down key. The default setting is 6.
•
Typematic Delay (Msec): Use this item to define how many milliseconds must elapse before a held-down key begins generating repeat characters. The default setting is 250.
Security Option If you have installed protection, this item defines if the is required at system start up, or if it is only required when a tries to enter the Setup Utility.
APIC Mode This item allows you to enable or disable the APIC (Advanced Programmable Interrupt Controller) mode. APIC provides symmetric multi-processing (SMP) for systems.
MPS Version Control For OS This item specifies which version of MPS (Multi-Processor Specification) this main board will use. Set this item for its default setting.
OS Select for DRAM > 64 MB This item is only required if you have installed more than 64 MB of memory and you are running the OS/2 operating system. Otherwise, leave this item at the default.
30 ed from www.Manualslib.com manuals search engine
Chapter 2
HDD S.M.A.R.T Capability The S.M.A.R.T (Self-Monitoring, Analysis, and Reporting Technology) system is a diagnostics technology that monitors and predicts device performance. S.M.A.R.T software resides on both the disk drive and the host computer.
Silent Boot This item enables or disables the Silent Boot function.
Small Logo (EPA) Show Determines whether the EPA logo appears during boot up.
Configuration Table This item enables or disables the Configuration Table in BIOS setting.
Bootblock Write Protect When enabled, Boot block write protection allows the boot block area to be protected by a write-protect pin.
Chapter 2 ed from www.Manualslib.com manuals search engine
31
Hard Disk Boot Priority Scroll to this item and press ENTER to enter the sub-menu below.
Phoenix - Award WorkstationBIOS CMOS Setup Utility Hard Disk Boot Priority 1. Ch2 M.
: ST3808110AS
Help Item
2. Bootable Add-in Cards
Menu Level
XX
Use
KLIJ :Move Enter: Select +/-/PU/PD :Value F10: Save and Exit ESC:Exit F1: General Help
32 ed from www.Manualslib.com manuals search engine
F5: Previous Values
F7: Optimized Defaults
Chapter 2
Advanced Chipset Features These items define critical timing parameters of the main board. You should set these items for their default values unless you are very familiar with the technical specification of your system hardware. If you change the values incorrectly, you may introduce fatal errors or recurring instability into your system.
Phoenix - Award WorkstationBIOS CMOS Setup Utility Advanced Chipset Features UMA Frame Buffer Size
[Auto]
Current UMA Size
256MB
Memory Hole
[Disabled]
System BIOS Cacheable
[Disabled]
Help Item Menu Level
X
KLIJ :Move Enter: Select +/-/PU/PD :Value F10: Save and Exit ESC:Exit F1: General Help
F5: Previous Values
F7: Optimized Defaults
UMA Frame Buffer Size This option controls the amount of system memory that is allocated to the integrated graphics processor when the system boots up.
Memory Hole You can reserve this area of system memory for ISA adapter ROM. When this area is reserved, it cannot be cached. The information of peripherals that use this area of system memory need to state their memory requirements.
System BIOS Cacheable Selecting [Enabled] allows caching of the system BIOS ROM at F0000h-FFFFFh, resulting in better system performance. However, if any program writes to this memory area, a system error may result. The default setting is [Disabled].
Chapter 2 ed from www.Manualslib.com manuals search engine
33
Integrated Peripherals Phoenix - Award WorkstationBIOS CMOS Setup Utility Integrated Peripherals XSouth OnChip IDE Device
[Press Enter]
XSouth OnChip PCI Device
[Press Enter]
XSuper IO Device
[Press Enter]
Init Display First
Help Item Menu Level
X
[PCIEx]
KLIJ :Move Enter: Select +/-/PU/PD :Value F10: Save and Exit ESC:Exit F1: General Help
F5: Previous Values
F7: Optimized Defaults
South OnChip IDE Device Press Enter to view the South OnChip IDE Device submenu. See “South OnChip IDE Device” on page 35.
South OnChip PCI Device Press Enter to view the South OnChip IDE Device submenu. See “South OnChip PCI Device” on page 36.
Super IO Device Press Enter to view the South OnChip PCI Device submenu. See “Super IO Device” on page 38.
Init Display First Enables or disables the bus PCI Slot or Onboard/AGP.
34 ed from www.Manualslib.com manuals search engine
Chapter 2
South OnChip IDE Device Scroll to this item and press Enter to enter the sub-menu shown as below.
Phoenix - Award WorkstationBIOS CMOS Setup Utility South OnChip IDE Device IDE DMA transfer access
[Enabled]
OnChip IDE Channel 0
[Enabled]
Primary Master PIO
[Auto]
Primary Slave PIO
[Auto]
Primary Master UDMA
[Auto]
Primary Slave UDMA
[Auto]
IDE HDD Block Mode
[Enabled]
Help Item Menu Level
X
KLIJ :Move Enter: Select +/-/PU/PD :Value F10: Save and Exit ESC:Exit F1: General Help
F5: Previous Values
F7: Optimized Defaults
IDE DMA Transfer Access This item allows you to enable the transfer access of the IDE DMA.
OnChip IDE Channel Select Enabled to activate IDE channel.
IDE Primary/Secondary Master/Slave PIO Each IDE channel s a master device and a slave device. These four items let you assign which kind of PIO (Programmed Input/Output) is used by IDE devices. Choose Auto to let the system auto detect which PIO mode is optimal, or select a PIO mode from zero to four.
IDE Primary/Secondary Master/Slave UltrA This main board s UltrA technology, which provides faster access to IDE devices. If you install a device that s UltrA, you can change the item on this list to Auto. You may have to install the UltrA driver supplied with this main board in order to use an UltrA device.
IDE HDD Block Mode Enable this field if the IDE hard drive s block mode. Block mode enables BIOS to automatically detect the optimal number of block read and writes per sector that the drive can and improves the speed of access to IDE devices. Chapter 2 ed from www.Manualslib.com manuals search engine
35
South OnChip PCI Device Scroll to this item and press Enter to enter the sub-menu shown as below.
Phoenix - Award WorkstationBIOS CMOS Setup Utility South OnChip PCI Device ATI Azalia Audio
[Enabled]
ATI SATA Controller
[Enabled]
ATI SATA Type
[Native IDE]
USB EHCI Controller
[Enabled]
OnChip USB Controller
[Enabled]
OnChip USB KBC Controller
[Enabled]
USB Mouse
[Enabled]
Onboard LAN Controller
[Enabled]
Onboard Lan Boot ROM
[Enabled]
Onboard 1394 Controller
[Enabled]
Help Item Menu Level
X
KLIJ :Move Enter: Select +/-/PU/PD :Value F10: Save and Exit ESC:Exit
ATI Azalia Audio ATI Azalia Audio provides superior Audio Onboard, negating the need for 3rd party audio cards. The default setting is [Enabled].
ATI SATA Controller This item appears in the BIOS of motherboards with a secondary Serial ATA controller (separate from the motherboard chipset). When enabled, the secondary Serial ATA controller will function normally. Serial ATA devices connected to it will be accessible to the system. When disabled, the secondary Serial ATA controller will be disabled. Serial ATA devices connected to it will not be accessible to the system.
ATI SATA Type This item sets the SATA Cable Type in use. The default is [Native IDE].
USB EHCI Controller Enables or disables the Universal Serial Bus (USB) controller and Enhanced Host Controller Interface.
36 ed from www.Manualslib.com manuals search engine
Chapter 2
OnChip USB Controller Enables or disables the Universal Serial Bus (USB) controller and any USB peripherals present.
OnChip USB KBC Controller Enables or disables the Universal Serial Bus (USB) controller and USB keyboard if present.
USB Mouse You can enable this item if you want to use a mouse connected through the USB port in a legacy operating system (such as DOS) that does not Plug and Play.
Onboard LAN Controller This item allows s to enable or disable the onboard LAN Controller function.
Onboard Lan Boot ROM Use this item to enable or disable the booting from the onboard LAN or a network add-on card with a remote boot ROM installed.
Onboard 1394 Controller Use this item to enable or disable the onboard VIA 1394 device.
Chapter 2 ed from www.Manualslib.com manuals search engine
37
Super IO Device Phoenix - Award WorkstationBIOS CMOS Setup Utility Super IO Device Onboard FDC Controller
[Enabled]
Onbaord Serial Port 1
[3F8/IRQ4]
Onbaord Serial Port 2
[2F8/IRQ3]
UART Mode Select
[Normal]
X UR2 Duplex Mode
Menu Level
X
Half
Onboard Parallel Port
[378/IRQ7]
Parallel Port Mode
SPP
X E Mode Use DMA
Help Item
3
KLIJ :Move Enter: Select +/-/PU/PD :Value F10: Save and Exit ESC:Exit F1: General Help
F5: Previous Values
F7: Optimized Defaults
Onboard FDC Controller If your system has a floppy disk controller (FDC) installed on the system board and you want to use it, you can select Enabled. If you install an add-in FDC or the system has no floppy drive, select Disabled in this field.
Onboard Serial Port 1 This item allows s to manually set the address for serial port 1.
Onboard Serial Port 2 Use this item to enable or disable the onboard parallel port and to assign a port address.
UART Mode Select Select an operating mode for the serial port. The default is [Normal].
UR2 Duplex Mode This option is only available if an infrared port mode is selected in the UART Mode Select item. Select full or half duplex mode. Full-duplex mode permits simultaneous two-direction transmission. Half-duplex mode permits transmission in one direction only at a time. 38 ed from www.Manualslib.com manuals search engine
Chapter 2
Onboard Parallel Port Select a logical LPT port address and corresponding interrupt for the onboard parallel port.
Parallel Port Mode Use this item to set the parallel port mode. You can select SPP (Standard Parallel Port), E (Extended Capabilities Port), EPP (Enhanced Parallel Port), or EPP & E.
E Mode Use DMA When the onboard parallel port is set for E mode, the parallel port can use (DMA) 3 or (DMA) 1.
Chapter 2 ed from www.Manualslib.com manuals search engine
39
Power Management Setup The system has various power-saving modes including powering down the hard disk, turning off the video, suspending to RAM, and software power down that allows the system to be automatically resumed by certain events. The power-saving modes can be controlled by time-outs. If the system is inactive for a while, the time-outs begin counting. If the inactivity continues so that the time-out period elapses, the system enters a power-saving mode. If any item in the list of Reload Global Timer Events is Enabled, then any activity on that item will reset the time-out counters to zero. If the system is suspended or has been powered down by software, it can be resumed by a wake up call that is generated by incoming traffic to a modern, a LAN card, a PCI card, or a fixed alarm on the system real-time clock.
Phoenix - Award WorkstationBIOS CMOS Setup Utility Power Management Setup AI function
[Enabled]
AI Suspend Type
[S3(STR)]
C2 Disable/Enable
[Disabled]
Power Management Option
[ Define]
HDD Power Down
[Disabled]
Video Off Option
[Suspend -> Off]
Video Off Method
[V/H SYNC+Blank]
Soft-Off by PWRBTN
[Delay 4 sec]
PowerOn by PCI Card
[Enabled]
Modem Ring Resume
[Disabled]
USB Wake Up From S1/S2
[Enabled]
USB Wake Up From S4
[Disabled]
PS2 KB/MS Wake Up S1/S2
[Disabled]
Wake Up by Lan
[Disabled]
HPET
[Enabled]
PWRON After PWR-Fail
[Former-Sts]
RTC Alarm Resume
[Disabled]
X Date (of Month) X Resume Time (hh : mm : ss)
Help Item Menu Level
X
0 0: 0:0
KLIJ :Move Enter: Select +/-/PU/PD :Value F10: Save and Exit ESC:Exit F1: General Help
F5: Previous Values
F7: Optimized Defaults
AI Function This item allows s to enable or disable the AI power management function.
AI Suspend Type You can use this item to define how your system suspends. 40 ed from www.Manualslib.com manuals search engine
Chapter 2
CS2 Disable/Enable Enable or disable the AI C2 mode. Default is Disabled.
Power Management Option This item acts like a master switch for the power-saving modes and hard disk timeouts. If this item is set to Max Saving, power-saving modes occur after a short timeout. If this item is set to Min Saving, power-saving modes occur after a longer timeout. If the item is set to Define, manually define timeouts for the power-saving modes.
HDD Power Down Select the required period of inactivity after which the hard disk drive powers down while all other devices remain active.
Video Off Option This option defines if the video is powered down when the system is put into suspend mode.
Video Off Method This item defines how the video is powered down to save power.
Soft-Off by PWRBTN Under AI (Advanced Configuration and Power Management Interface) you can create a software power down. In a software power down, the system can be resumed by Wake Up Alarms. This item lets you install a software power down that is controlled by the power button on your system. If the item is set for Instant-Off, then the power button causes a software power down. If the item is set for Delay four Sec., then you have to hold the power button down for four seconds to cause a software power down.
Power On By PCI Card Enables PCI activity to wake up the system from a power-saving mode.
Modem Ring Resume Enables Modem activity to wake up the system from a power-saving mode.
USB Wakeup From S1/S2 Enables USB activity to wake up the system from S1 or S2.
USB Wakeup From S4 Enables USB activity to wake up the system from S4.
PS2 KB/MS Wakeup From S1/S2 Enables PS/2 keyboard or mouse activity to wake up the system from S1 or S2.
Wakeup By LAN Enables LAN activity to wake up the system from a power-saving mode.
HPET Enable or disable for the High Precision Event Timer (HPET).
PWRON After PWR-Fail Sets the state to which the computer returns after power failure. Chapter 2 ed from www.Manualslib.com manuals search engine
41
RTC Alarm Resume When set to Enabled, the Date and Resume Time fields become available. Set the date (day of the month), hour, minute and second to turn on the system. When set to 0 (zero) for the day of the month, the alarm will power on your system every day at the specified time.
42 ed from www.Manualslib.com manuals search engine
Chapter 2
PnP/PCI Configurations It configures how PnP (Plug and Play) and PCI expansion cards operate in your system. Both the ISA and PCI buses on the main board use system IRQs (interrupt requests) and DMAs (direct memory access). You must set up the IRQ and DMA assignments correctly through the PnP/PCI Configurations Setup Utility for the main board to work properly. Selecting PnP/PCI Configurations on the main program screen displays the menu below.
Phoenix - Award WorkstationBIOS CMOS Setup Utility PnP/PCI Configurations Reset Configuration Data
[Disabled]
Resources Controlled By
[Auto(ESCD)]
X IRQ Resources
Help Item Menu Level
X
Press Enter
PCI/VGA Palette Snoop
[Disabled]
Assign IRQ For VGA
[Enabled]
Assign IRQ For USB
[Enabled]
PC Latency Timer (CLK)
[64]
**PCI Express relative items** Maximum Payload Size
[4096]
KLIJ :Move Enter: Select +/-/PU/PD :Value F10: Save and Exit ESC:Exit F1: General Help
F5: Previous Values
F7: Optimized Defaults
Reset Configuration Data Select Enabled to reset the Extended System Configuration Data (ESCD) when you exit setup. This option is useful when installing new add-ons. If the computer cannot boot after add-on installation, this option resets the ESCD allowing the computer to reboot. The default setting is disabled.
Resources Controlled By The BIOS can automatically configure all the boot Plug and Play compatible devices. Auto (default) disables IRQ and DMA memory base address fields as they are automatically assigned.
PCI/VGA Palette Snoop This item is designed to overcome problems that can be caused by some non-standard VGA cards. This board includes a built-in VGA system that does not require palette snooping. Default setting is [Disabled].
Assign IRQ For VGA Enable or disable IRQ allocation for the graphics card.
Chapter 2 ed from www.Manualslib.com manuals search engine
43
Assign IRQ for USB Enable or disable IRQ allocation for the USB (Universal Serial Bus).
PCI Latency Timer (CLK) This item controls how long a PCI device can hold the PCI bus before another device takes over. Setting the latency to longer periods enables a PCI device to retain control of the bus longer before handing it over to another device.
Maximum Payload Size This BIOS feature determines the maximum TLP (Transaction Layer Packet) payload size that can be ed by the motherboard chipset's PCI Express controller. The TLP payload size determines the amount of data transmitted within each data packet. When set to 4096, the motherboard chipset's PCI Express controller s the maximum data payload of 4096 bytes within each TLP. This is the maximum payload size currently ed by the PCI Express protocol.
44 ed from www.Manualslib.com manuals search engine
Chapter 2
PC Health Status On the main board that s hardware monitoring, you can monitor the parameters of critical voltage, temperature and fan speed.
Phoenix - Award WorkstationBIOS CMOS Setup Utility PC Health Status U Shutdown Temperature
[90°C/174°C]
U Vcore
[1.34V]
+3.3V
[3.32V]
+5V
[5.08V]
+12V
[11.96V]
+5VSB
[4.94V]
U Temperature
64°C
Ambient Temperature
31°C
U FAN speed
1844 RPM
System FAN speed
1790 RPM
U Temp. Offset
[255]
U Warning Temperature
[Disabled]
U Smart FAN Control
[Enabled]
PWM Start U Temp (°C)
[ 35]
Start PWM Value (0~127)
[ 64]
Slope PWM Value
[ 3]
Delta Temp. (°C)
[ 2]
PWM Start SYS Temp. (°C)
[ 45]
Slope PWM Value 2
[ 2]
Delta Temp. (°C) 2
[ 2]
System Smart FAN Control
[Enabled]
PWM Start U Temp (°C)
[ 45]
Start PWM Value (0~127)
[ 48]
Slope PWM Value
[ 2]
Delta Temp. (°C)
[ 2]
PWM Start SYS Temp. (°C)
[ 42]
Slope PWM Value 2
[ 3]
Delta Temp. (°C) 2
[ 2]
Help Item Menu Level
X
KLIJ :Move Enter: Select +/-/PU/PD :Value F10: Save and Exit ESC:Exit F1: General Help
F5: Previous Values
F7: Optimized Defaults
U Shut Down Temperature Enables you to set the maximum temperature that the system can reach before powering down.
Chapter 2 ed from www.Manualslib.com manuals search engine
45
Component Status The following items display the current status of various components. •
U VCore
•
+3.3V
•
+5V
•
+12V
•
+5VSB
•
U Temperature
•
Ambient Temperature
•
U FAN speed
•
System FAN speed
Scroll to these items and enter values as required to customize the Thermal Profile: •
U Temp. Offset
•
U Warning Temperature
•
U Smart FAN Control
•
PWM Start U Temp
•
Start PWM Value
•
Slope PWM Value
•
Delta Temp.
•
PWM Start SYS Temp.
•
Slope PWM Value 2
•
Delta Temp. (°C) 2
•
System Smart FAN Control
•
PWM Start U Temp (°C)
•
Start PWM Value (0~127)
•
Slope PWM Value
•
Delta Temp. (°C)
•
PWM Start SYS Temp. (°C)
•
Slope PWM Value 2
•
Delta Temp. (°C) 2
46 ed from www.Manualslib.com manuals search engine
Chapter 2
Frequency & Voltage Control It enables you to set the clock speed and system bus for your system. The clock speed and system bus are determined by the processor you have installed in your system.
Phoenix - Award WorkstationBIOS CMOS Setup Utility Frequency/Voltage Control Spread Spectrum
[Disabled]
SB600 Spread Spectrum
[Disabled]
Help Item Menu Level
X
KLIJ :Move Enter: Select +/-/PU/PD :Value F10: Save and Exit ESC:Exit F1: General Help
F5: Previous Values
F7: Optimized Defaults
Spread Spectrum If you enable spread spectrum, it can significantly reduce the EMI (Electro-Magnetic Interference) generated by the system.
SB600 Spread Spectrum Enabling spread spectrum can significantly reduce the EMI (ElectroMagnetic Interference) generated by the south bridge. For maximum system stability and performance this settings should remain at the default setting [Disabled].
Chapter 2 ed from www.Manualslib.com manuals search engine
47
Load Optimized Defaults This option opens a dialog box that lets you install optimized defaults for all appropriate items in the Setup Utility. Press Y and then ENTER to install the defaults. Press N and then ENTER to cancel without installing defaults.
Phoenix - Award WorkstationBIOS CMOS Setup Utility XProduct Information
XPC Health Status
XStandard CMOS Features
XFrequency/Voltage Control
XAdvanced BIOS Features
Load Optimized Defaults
XAdvanced Chipset Features
Set Supervisor
XIntegrated Peripherals
Set
XPower Management Setup XPnP/PCI Configuration
Save & Exit Setup Load Optimized Defaults (Y/N)? Exit Without Saving
KLIJ : Select Item
Esc: Quit F10: Save & Exit Setup
Load Optimized Defaults V02.54 (C) Copyright 1985-2004, American Megatrends, Inc.
48 ed from www.Manualslib.com manuals search engine
Chapter 2
Set Supervisor When this function is selected, the following message appears at the center of the screen to assist you in creating a .
Phoenix - Award WorkstationBIOS CMOS Setup Utility XProduct Information
XPC Health Status
XStandard CMOS Features
XFrequency/Voltage Control
XAdvanced BIOS Features
Load Optimized Defaults
XAdvanced Chipset Features
Set Supervisor
XIntegrated Peripherals XPower Management Setup XPnP/PCI Configuration
Set Enter :Save & Exit Setup
Exit Without Saving
KLIJ : Select Item
Esc: Quit F10: Save & Exit Setup
Change/Set/Disable V02.54 (C) Copyright 1985-2004, American Megatrends, Inc.
Enter Type the , up to eight characters, and press ENTER. The entered here overwrites any previously entered from CMOS memory. You will be asked to confirm the . Type the again and press ENTER. You can press ESC to abort the selection. To disable , just press ENTER when you are prompted to enter . A message will confirm the being disabled. Once the is disabled, the system will boot and you can enter BIOS Setup freely. Supervisor has higher priority than . You can use Supervisor when booting the system or entering BIOS Setup to modify all settings. Also you can use when booting the system or entering BIOS Setup but can not modify any setting if Supervisor is enabled.
Chapter 2 ed from www.Manualslib.com manuals search engine
49
Save and Exit Setup You can highlight this item and press ENTER to save the changes that you have made in the Setup Utility and exit the Setup Utility.
Phoenix - Award WorkstationBIOS CMOS Setup Utility XProduct Information
XPC Health Status
XStandard CMOS Features
XFrequency/Voltage Control
XAdvanced BIOS Features
Load Optimized Defaults
XAdvanced Chipset Features
Set Supervisor
XIntegrated Peripherals XPower Management Setup XPnP/PCI Configuration
Set
SAVE to CMOS and EXIT (Y/N)?
Save & Exit Setup Exit Without Saving
KLIJ : Select Item
Esc: Quit F10: Save & Exit Setup
Save Data to CMOS V02.54 (C) Copyright 1985-2004, American Megatrends, Inc. When the Save and Exit dialog box appears, press (Y) followed by ENTER to save and exit, or press (N) followed by ENTER to return to the main menu.
50 ed from www.Manualslib.com manuals search engine
Chapter 2
Exit without Saving You can highlight this item and press ENTER to discard any changes that you have made in the Setup Utility and exit the Setup Utility.
Phoenix - Award WorkstationBIOS CMOS Setup Utility XProduct Information
XPC Health Status
XStandard CMOS Features
XFrequency/Voltage Control
XAdvanced BIOS Features
Load Optimized Defaults
XAdvanced Chipset Features
Set Supervisor
XIntegrated Peripherals XPower Management Setup XPnP/PCI Configuration
Set Quit Without Saving Save(Y/N)? & Exit Setup
Exit Without Saving
KLIJ : Select Item
Esc: Quit F10: Save & Exit Setup
Abandon All Data V02.54 (C) Copyright 1985-2004, American Megatrends, Inc. When the Exit without Saving dialog box appears, press (Y) followed by ENTER to discard changes and exit, or press (N) followed by ENTER to return to the main menu. Note: If you have made changes to settings that you do not want to save, choose the Discard Changes and Exit and press (Y) followed by ENTER to discard any changes you have made.
Chapter 2 ed from www.Manualslib.com manuals search engine
51
52 ed from www.Manualslib.com manuals search engine
Chapter 2
Chapter 3
Machine Disassembly and Replacement General Information This chapter contains step-by-step procedures on how to disassemble and reassemble the Angora AM5610/ AM3610 for maintenance and troubleshooting. In the coming pages, the first part of the disassembly instruction is for Angora AM5610 and the second part is for Angora AM3610. To disassemble the notebook, you need the tools below: •
Wrist ground strap and conductive mat for preventing electrostatic discharge
•
Small Philips screw driver
•
Flat head screw driver
•
Hexagonal driver
•
Tweezers
Note: The screws for the different components vary in size. During the disassembly process, group the screws with the corresponding components to avoid mismatch when putting back the components. When you remove the stripe cover, please be careful not to scrape the cover.
Before You Begin Before proceeding with the disassembly procedure, you have to make sure that: •
The system and all peripherals are powered off.
•
The AC adaptor and all power and signal cables from the system are unplugged.
Note: There are several types of screws used to secure the main unit. The screws vary in length. Please refer to the screws table after the flowchart. Group the same type of screws together during service disassembling. Please also the screw location for each screw type. If you fasten the screws on the wrong location, the long screws may cause irrecoverable damage to the main board.
Chapter 3 ed from www.Manualslib.com manuals search engine
53
Angora AM50/30/10 Procedures Use the following guides to disassemble and reassemble the AM50, AM30, and AM10 models. Note: The only differences between the models are the front bezel and placement of the USB as shown below. Take care when replacing the front bezel to avoid damage to the ports. AM50
AM30
AM10
Disassembly Procedure 1. Place the system unit on a flat, steady and nonskid surface. 2. Release the lock handle then slide the left cover out.
3. Detach the VGA, TV, and Modem cards.
54 ed from www.Manualslib.com manuals search engine
Chapter 3
4. Disconnect the front bezel LED cable.
5. Disconnect the audio cables.
6. Disconnect the USB cables.
7. Disconnect the SPDIF cable.
Chapter 3 ed from www.Manualslib.com manuals search engine
55
8. Disconnect the PA power cable from the MB connector.
9. Disconnect the P1 power and FDD data cables. P1 Power Cable
FDD Data Cable
10. Disconnect the ODD power and data cables. ODD Power Cable ODD Data Cable
56 ed from www.Manualslib.com manuals search engine
Chapter 3
11. Disconnect the HDD power and data cables.
12. Disconnect the System Fan and U Cooler power cable from their MB connectors. U Cooler
System Fan
13. Slide the HDD holder as shown and remove the HDD from the chassis.
Chapter 3 ed from www.Manualslib.com manuals search engine
57
14. Release the three securing latches and remove the front bezel. Note: For the AM50 and AM30, take care not to damage the USB ports at the top of the bezel. Note: For the AM10, take care not to damage the USB ports on the bottom right-hand side of the bezel. AM50
AM30
AM10
15. Slide the ODD holder as shown and remove the HDD from the chassis.
16. Release the four screws as shown and remove the U Cooler from the chassis.
58 ed from www.Manualslib.com manuals search engine
Chapter 3
17. Push the two locking latches away from the memory unit at the same time to release the memory. Repeat as necessary to remove all memory.
18. Remove the four System Fan screws as shown and lift the fan clear of the chassis.
19. Push and release the U latch and remove the U from the motherboard.
Chapter 3 ed from www.Manualslib.com manuals search engine
59
20. Release the 8 screws marked below and remove the main board.
21. Release the four screws marked below and remove the system power supply from the chassis.
60 ed from www.Manualslib.com manuals search engine
Chapter 3
Reassembly Procedure 1.
Insert the system power supply in to the chassis and secure the four screws marked below.
IMPORTANT:FSP and LITEON power supply cabling differ due to size constraints. For FSP power supplies, use a power cable clip to secure the 12V cable. For LITEON power supplies, use a non-cable clip to secure the 12V cable. FSP Power Supply
LITEON Power Supply
2. Insert the main board and secure the 8 screws marked below. Note: Ensure that the I/O Connector is aligned and that the VIA aperture is correctly oriented with the STAND OFF on the chassis.
Chapter 3 ed from www.Manualslib.com manuals search engine
61
3. Insert the U in to the motherboard. Close the U latch.
4. Insert the System Fan in to the chassis as secure the 4 screws as shown.
5. Insert the memory into the slot, taking care to align the locating lug. Push down as shown until the securing latches click into place. Repeat for all memory modules.
62 ed from www.Manualslib.com manuals search engine
Chapter 3
6. Fit the U cooler to the MB and fasten the four screws shown bellow.
7. Connect the System Fan & U Cooler power-cables to the MB connectors. U Cooler
System Fan
8. Insert the ODD in to the chassis and slide the ODD holder as shown to lock it in place.
Chapter 3 ed from www.Manualslib.com manuals search engine
63
9. Insert the FDD in to the chassis and slide the FDD holder as shown to lock it in place.
10. Attach the front bezel as shown. Ensure that access to the USB ports is not restricted as indicated for the three models. AM50
AM30
AM10
11. Insert the SPDIF into the chassis. Ensure that the unit locates correctly as shown.
12. Insert the HDD in to the chassis and slide the HDD holder as shown to lock it in place.
64 ed from www.Manualslib.com manuals search engine
Chapter 3
13. Connect the HDD data cable and HDD power cable.
14. Connect the ODD data cable and power-cable to the rear of ODD. ODD Power Cable ODD Data Cable
15. Connect the P1 power-cable and FDD data cable to the MB connector. P1 Power Cable
Chapter 3 ed from www.Manualslib.com manuals search engine
FDD Data Cable
65
16. Connect the PA power-cable to the MB connector.
17. Connect the USB cables.
18. Connect the SPDIF cable.
19. Connect the audio cables.
66 ed from www.Manualslib.com manuals search engine
Chapter 3
20. Connect the front bezel LED cable.
21. Connect the VGA/TV, and Modem cards.
22. Slide the left cover in and secure the lock handle.
Chapter 3 ed from www.Manualslib.com manuals search engine
67
68 ed from www.Manualslib.com manuals search engine
Chapter 3
Chapter 4
Troubleshooting Please refer to generic troubleshooting guide in the service guide database for information with respect to following items: •
Power-On Self-Test (POST)
•
POST Check Points
•
POST Error Messages List
•
Error Symptoms List
Chapter 4 ed from www.Manualslib.com manuals search engine
69
70 ed from www.Manualslib.com manuals search engine
Chapter 4
Chapter 5
Jumper and Connector Information Introduction to Connectors Main Board Placement 1
11
30 31 32
29
2 3 21 4
26
5 6
33 34
12 13 14
7 8
25
22
15
35
16 9
10
36
17
27 23
18 19 20
24
28
Component
#
Component
1
PS/2 CONN
2
HDMI CONN
3
LPT CONN
4
VGA CONN
5
1394 CONN
6
USB CONNS
7
LAN CONN
8
AUDIO CONNS
9
LAN CHIP
10
AUDIO CHIP
11
4 PIN POWER
12
SYSTEM FAN
13
U FAN
14
COM PORT
15
CLK GEN
16
PCIE 1X SLOT
ed from www.Manualslib.com manuals search engine
39 40
#
Chapter 5
37 38
41
71
17
PCIE 16X SLOT
18
PCI SLOTS
19
FRONT AUDIO HEADER
20
AUX_IN HEADER
21
U SOCKET
22
NORTH BRIDGE
23
1394 CHIP
24
FRONT 1394 HEADER
25
BATTERY
26
DIMM SLOTS
27
SOUTH BRIDGE
28
FRONT USB HEADER
29
SI/O CHIP
30
AS HEADER 2
31
AS HEADER 1
32
INTR HEADER
33
24 PIN POWER
34
FLOPPY CONN
35
IDE CONN
36
BIOS
37
CLR_CMOS HEADER
38
OBR HEADER
39
SPEAKER HEADER
40
SATA CONN
41
FRONT
72 ed from www.Manualslib.com manuals search engine
Chapter 5
Connectors USB Connectors 1394_USBX2(For 1394) Pin
Signal Name
Pin
Signal Name
1, 5
RUSB_VCC1
9
DCOUT_1394
2
USBD0-
11
TPB0-
3
USBD0+
12
TPB0+
4
Ground
13
TPA0-
6
USBD1-
14
TPA0+
7
USBD1+
15 - 22
IO_GND
8,10
Ground
LAN USB_2 Pin
Signal Name
Pin
Signal Name
1,5
RUSB_VCC2(5V)
13
MDI1-
2
SBD2-
14
MDI2+
3
SBD3-
15
MDI2-
4,8
GND
16
MDI3+
6
SBD2+
17
MDI3-
7
SBD3+
18
GND
23 - 30
Ground
19
LAN_LED
9
AVDDL_1D8V
20
LAN_LINK_LED
10
MDI0+
21
LED_100#
11
MDI0-
22
LED_1000#
12
MDI1+
Note: Pins 9-18 for RJ-45 LAN Jack pin definition, 19-22 for LAN LED definition.
Audio Backup Connectors AUDIO1F (Right Side /Light Blue in Color) Pin
Signal Name
61
GND
62
LINE1_L2
63
LINE1-JD
64
GND
65
LINE1_R5
Chapter 5 ed from www.Manualslib.com manuals search engine
73
AUDIO1E (Right Side /FRONT Lime in Color) Pin
Signal Name
51
GND
52
LINE_OUT_L2
53
FRONT-JD
54
GND
55
LINE_OUT_R5
AUDIO1D (Right Side /Pink in Color) Pin
Signal Name
41
GND
42
MIC1_L2
43
MIC1-JD
44
GND
45
MIC1_R5
AUDIO1A (Left Side/Gray in Color) Pin
Signal Name
1
GND
2
SIDESURRBACK_L2
3
SIDESURR-JD
4
GND
5
SIDESURRBACK_R2
AUDIO1C (Left Side, Orange in Color) Pin
Signal Name
31
GND
32
CEN-C
33
CEN-JD
34
GND
35
LFE-C
AUDIO1D (Left Side, Black in Color) Pin
Signal Name
21
GND
22
SURR_L
23
SURR-JD
24
GND
25
SURR_R
74 ed from www.Manualslib.com manuals search engine
Chapter 5
IDE/SATA 40-pin (2x20) PIDE Headers Pin
Signal Name
Pin
Signal Name
1
HD_RST#
2
Ground
3
PDD7
4
PDD8
5
PDD6
6
PDD9
7
PDD5
8
PDD10
9
PDD4
10
PDD11
11
PDD3
12
PDD12
13
PDD2
14
PDD13
15
PDD1
16
PDD14
17
IPDD0
18
PDD15
19
Ground
20
Key
21
PD_REQ
22
Ground
23
PD_IOW#
24
Ground
25
PD_IOR#
26
Ground
27
PD_RDY
28
Ground
29
PD_ACK#
30
Ground
31
IRQ14_R
32
N/C
33
PD_A1
34
PD_DET
35
PD_A0
36
PD_A2
37
PD_CS1#
38
PD_CS3#
39
IDE_LED#
40
Ground
1x7-pin SATA Headers Pin
Signal Name
1
GND
2
SATA_TX0+_C
3
SATA_TX0-_C
4
GND
5
SATA_RX0-_C
6
SATA_RX0+_C
7
GND
8
KEY
9
KEY
Chapter 5 ed from www.Manualslib.com manuals search engine
75
VGA Pin
Signal Name
Pin
Signal Name
1
CONN_RED
9
5V_DVI
2
CONN_GREEN
10
GND
3
CONN_BLUE
11
GND
4
GND
12
CONN_DAC_SDAT
5
GND
13
CONN_HSYNC#
6
GND
14
CONN_VSYNC#
7
GND
15
CONN_DAC_SCL
8
GND
HDMI Pin
Signal Name
Pin
Signal Name
1
HDMI_TXAP2
12
HDMI_TXCAN
2
GND
13
NC
3
HDMI_TXAN2
14
NC
4
HDMI_TXAP1
15
HDMI_DDC_CLK
5
GND
16
HDMI_DDC_DATA
6
HDMI_TXAN1
17
GND
7
HDMI_TXAP0
18
5V_S0
8
GND
19
HDMI_HOT_PLUG_DETECT
9
HDMI_TXAN0
20
GND
10
HDMI_TXCAP
21
GND
11
GND
76 ed from www.Manualslib.com manuals search engine
Chapter 5
Jumpers Jumper/Header Name
Function
Definition
UFAN (3 PIN)
U FAN HEADER
1: GND 2: POWER 3: SENSE
Yellow is symbol, Red is Pin1 of symbol SYSFAN (3 PIN)
SYSTEM FAN HEADER
1: GND 2: POWER 3: SENSE
Yellow is symbol, Red is Pin1 of symbol CLR_CMOS (3 PIN)
CLEAR CMOS HEADER
1,2: CLEAR CMOS (1: Ground, 2: RTC_RSTJ) 2,3: NORMAL (3: VCC_RTC)
Yellow is symbol, Red is Pin1 of symbol OBR
System Recover HEADER
1: SYS_RECOVER 2: GND
Yellow is symbol, Red is Pin1 of symbol
Chapter 5 ed from www.Manualslib.com manuals search engine
77
Jumper/Header Name
Function
Definition
F_USB1, F_USB2, F_USB3
FRONT USB HEADER (2x5)
1: VCC5 2: VCC5 3: D04: D15: D0+ 6: D1+ 7: GND 8: GND 9: KEY 10: GND
Yellow is symbol, Red is Pin1 of symbol
F_AUDIO1
FRONT AUDIO HEADER (2x5)
1: FMIC_L 2: GND 3: FMIC_R 4: 3D3V_S0 5: LINE_OUT_R 6: MIC_JD 7: FRONT-IO-SENSE 8: KEY 9: LINE_OUT_L 10: LINE_JD
Yellow is symbol, Red is Pin1 of symbol IR
IR
1: VCC5 2: KEY 3: IRRX 4: GND 5: IRTX
78 ed from www.Manualslib.com manuals search engine
Chapter 5
Jumper/Header Name
Function
Definition
F_1394_1
FRONT 1394 HEADER
1: TPA+ 2: TPA3: GND 4: GND 5: TPB+ 6: TPB7: POWER 8: POWER 9: KEY 10: GND
Yellow is symbol, Red is Pin1 of symbol FP
Front Header
1: FP_1(PU 5V_S0) 2: LEDP(PU 5V_S5) 3: SATA_LED_L 4: PMSLED(PU 5V_S5) 5: GND 6: SWITCH_ON* 7: FP_RESET*_FP 8: GND 9: FP_9(PU 5V_S0) 10: KEY 11: FP_11(PU 5V_S0) 12: FP_12(PU 5V_S5) 13: ODD_LED* 14: LAN_LED
Yellow is symbol, Red is Pin1 of symbol
Chapter 5 ed from www.Manualslib.com manuals search engine
79
Jumper/Header Name
Function
Definition
COM1, COM2
COM Port Header
1: NDCD 2: NSIN 3: NSOUT 4: NDTR 5: GND 6: NDSR 7: NRTS 8: NCTS 9: NRI 10: KEY
Yellow is symbol, Red is Pin1 of symbol
INTERNAL SPEAKER HEADER
AUDIO INTERNAL SPEAKER HEADER
1: MONO_L 2: GND 3: MONO_R 4: KEY 5: GND 6: GND 7: VCC3 8: VCC5
Yellow is symbol, Red is Pin1 of symbol
80 ed from www.Manualslib.com manuals search engine
Chapter 5
Jumper/Header Name
Function
Definition
TPM
TPM HEADER
1: LCKL 2: GND 3: LFRAMEn 4: KEY 5: LRESETn 6: NC 7: LAD3 8: LAD2 9: VDD (3.3V) 10: LAD1 11: LAD0 12: GND 13: NC 14: NC 15: NC 16: SERIRQ 17: GND
Yellow is symbol, Red is Pin1 of symbol
18: CLKRUNin 19: LPDn 20: NC
Chapter 5 ed from www.Manualslib.com manuals search engine
81
82 ed from www.Manualslib.com manuals search engine
Chapter 5
Chapter 6
FRU (Field Replaceable Unit) List This chapter offers the FRU (Field Replaceable Unit) list in global configuration of Angora AM5610 and AM3610 desktop. Refer to this chapter whenever ordering the parts to repair or for RMA (Return Merchandise Authorization). Please note that when ordering FRU parts, you should check the most up-to-date information available on your regional web or channel. For whatever reasons a part number is changed, it will NOT be noted on the printed service guide. For Acer authorized service providers, your Acer office may have a different part number code from those given in the FRU list of this printed service guide. You MUST use the local FRU list provided by your regional Acer office to order FRU parts for service. Note: To scrap or to return the defective parts, you should follow the local government ordinance or regulations on how to dispose them properly, or follow the rules set by your regional Acer office on how to return it.
Chapter 6 ed from www.Manualslib.com manuals search engine
83
Angora AM50 Exploded Diagram
Number
Description
Number
1
AM50 Bezel
10
Power Supply
2
AM50 USB
11
Fan
3
AM50 USB
12
PCI Bracket
4
FDD Lock Slide
13
Left Slide Door
5
CD ROM Lock Slide
14
Motherboard
6
Chassis
15
HDD
7
USB PCB ASM
16
3.5” Device
8
USB Shielding
17
CD ROM
9
Right Slide Door
18
HDD Lock Slide
84 ed from www.Manualslib.com manuals search engine
Description
Chapter 6
Angora AM30 Exploded Diagram
Number
Description
Number
Description
1
AM30 Main Bezel
11
Fan
2
3_25 Cover
12
PCI Bracket
3
5_25 Cover
13
Left Side Door
4
AM50 USB
14
Motherboard
5
AM50 USB
15
HDD
6
Chassis
16
3.5” Device
7
USB PCB ASM
17
CD ROM
8
USB Shielding
18
HDD Lock Slide
9
Right Side Door
19
FDD Lock Slide
10
Power Supply
20
CD ROM Lock Slide
Chapter 6 ed from www.Manualslib.com manuals search engine
85
Angora AM10 Exploded Diagram
Number
Description
1
AM10 Main Bezel
2 3
Number
Description
10
Power Supply
3_25 Cover
11
Fan
5_25 Cover
12
PCI Bracket
4
AM50 USB
13
Left Side Door
5
AM50 USB
14
Motherboard
6
FDD Lock Slide
15
HDD Lock Slide
7
CD ROM Lock Slide
16
HDD
8
Chassis
17
3.5” Device
9
Right Side Door
18
CD ROM
86 ed from www.Manualslib.com manuals search engine
Chapter 6
Related Documents c2h70
Acer Aspire M1100 6o25u
November 2019 78
Aspire M1100 Specifications b6v2s
December 2019 86
Acer Aspire 1350 2z6q4g
August 2021 0
Acer Aspire 5750_5750g_compal_la-6902p.pdf 15226x
October 2022 0
Manual Acer Aspire R11 1g1c5c
November 2019 59
Acer Aspire Timelinex 5820tg 2n1b5h
November 2019 204More Documents from "Reginald Sosa" n2p5a
Samsung Ps51d550c1wxbt F82a 04 Troubleshooting(map) [sm] 1c3o
December 2019 76
Acer Aspire M1100 6o25u
November 2019 78
Odisseia De Homero Pdf 515v6k
October 2019 65
Evaporative Condenser Design Pdf 5cb2w
December 2019 58
Syllabus Ncm 103 Final 52482f
October 2019 57